Related
Hello all...
Does anyone know how to open a Kaiser? I've got all the tools but I just can't find how to open it to replace the LCD screen.
Thanks.
Regards,
Mario.
Mario_Nissan said:
Hello all...
Does anyone know how to open a Kaiser? I've got all the tools but I just can't find how to open it to replace the LCD screen.
Thanks.
Regards,
Mario.
Click to expand...
Click to collapse
Find some links on this page:
www.mikechannon.net
OR the Kaiser Service Manual
Kaiser Service Manual
Mike
After many hours I got to open the Kaiser without causing any damage.
Tips:
- To remove the screen you just need to remove the 4 screws from behind the moving part.
- Be carefull because when you remove the cover there's a silver tiny screw connected to the speaker that you need to remover or you'll cause damage to the speaker and videoconferencing camera.
- I just used: T6, T4 and Phillips screwdrivers.
I'm posting some pictures.
Hope this helps to someone else...
Regards,
Mario Nissan
www.tecnosinergia.com
currently trying right now (so i can see which connector i have) 4 screws are out but nothing seems to have losened up for removal
After removing the 4 screws you'll need a very thin tool to insert it between the screen cover and the screen casing. You have to be very carefull not to damage the cover, and make sure not to pull the cover too hard because you'll need to remove the speaker board screw first.
To remove the cover with the thin tool I started at the top and bottom of the device and then slided it over the whole device until the cover got loose.
Hope this helps...
Regards,
Mario
Thanks for your help, looking to acquire a plastic tool for that...dont' want to use anything metalic and increase the risk of damaging anything more
I can't tell from the detail of the pictures, but how "integrated" is the front camera? Is it something I can possibly just "snap in" on my Tilt, or does a whole section have to be modified? I don't mind the idea of dremeling in a hole on the front panel.
Anyone know how I can quickly obtain the front camera and required connections/circuitry to apply it to my Tilt?
Hey Mario, Does this mean you didn't send in you Kaiser to HTC? I assume u went thru NJbridges. If so, are you up and running now? (determining what I should do)
I would also like to know how plausible it would be to add a front camera to the tilt.
What kind of connection is it?
Where can we get the part?
Hello all,
When removing the front cover you have to be carefull because the borad that holds the camera and the speaker is scrwed to the cover and if you pull it too hard you'll break the cables.
I went thru njbridges and I'm waiting for the replacement LCD, it's supposed to be here on Monday or Tuesday. I'll let you know the results. IMPORTANT: There are two LCD models differentiated by the color of the cable and connector, make sure you check that before ordering.
I didn't send my device to HTC because I live in Mexico and I needed a US address, plus they said the replacement could cost between $170 and $370 and I think they don't have the replacement LCD's in stock yet.
If you have a Tilt I don't think you'll be able to add a front camera to it.
Hope this helps!
Best Regards,
Mario.
Thanks Mario, still haven't fount a proper tool to open it as of yet. But please keep me posted on if you got you TyTn II working with the new screen, I have the same feeling about HTC US and the screen. got two different answers on two different calls.
Mario_Nissan said:
Hello all,
When removing the front cover you have to be carefull because the borad that holds the camera and the speaker is scrwed to the cover and if you pull it too hard you'll break the cables.
I went thru njbridges and I'm waiting for the replacement LCD, it's supposed to be here on Monday or Tuesday. I'll let you know the results. IMPORTANT: There are two LCD models differentiated by the color of the cable and connector, make sure you check that before ordering.
I didn't send my device to HTC because I live in Mexico and I needed a US address, plus they said the replacement could cost between $170 and $370 and I think they don't have the replacement LCD's in stock yet.
If you have a Tilt I don't think you'll be able to add a front camera to it.
Hope this helps!
Best Regards,
Mario.
Click to expand...
Click to collapse
So there is two LCD models? That explains why my replacement Tilt (which I sent back because I did not like, waiting for another) had a screen with a weired greenish tint to it.
Dude where did you get your LCD screen replacement? What's NJBRIDGES? Googled it but couldn't find a link. I need one badly!
Is this a universal LCD screen? Can I use older LCD screens from Blue Angel? Hermes? Etc?
Mario_Nissan said:
Hello all...
Does anyone know how to open a Kaiser? I've got all the tools but I just can't find how to open it to replace the LCD screen.
Thanks.
Regards,
Mario.
Click to expand...
Click to collapse
search njbridges in the forum its a member here that sells them. Send him a PM.
no its not universal so don't bother trying to connect an older LCD to it.
BeyondtheTech said:
I can't tell from the detail of the pictures, but how "integrated" is the front camera? Is it something I can possibly just "snap in" on my Tilt, or does a whole section have to be modified? I don't mind the idea of dremeling in a hole on the front panel.
Anyone know how I can quickly obtain the front camera and required connections/circuitry to apply it to my Tilt?
Click to expand...
Click to collapse
Hey is it not just cheeper to sell it on ebay and get a kaiser? But i didnt message u to make fun of u lol i was really interested in knowing why you would need a front camera on a tilt? I am assuiming you are using it with ATT (I have a MDA VARIO III which has the front camera and plan to use it with ATT) and I thought they dont support Video Telephony...or do they now?
Hey Mario,
Just checking if you had any progress with this yet.
Hello,
I just came back from my trip and the UPS package with the new LCD was waiting for me...
I replaced the LCD in about 30 minutes and so far I've been using my Kaiser for about 3 hours without any problems.
I got my LCD screen from njbridges.
Happy again!!!!
Regards,
Mario.
Mario_Nissan said:
Hello all,
I didn't send my device to HTC because I live in Mexico and I needed a US address, plus they said the replacement could cost between $170 and $370 and I think they don't have the replacement LCD's in stock yet.
QUOTE]
Mario, I live in Mexico too. Do you the settings for a Telcel data connection? I went into the Telcel office in Merida and they said "we´ll have to take the phone in for two days, and then maybe"...yeah right!!!!!!
It´ll stop the damned annoying message that keeps poping up too!
Click to expand...
Click to collapse
Hello timfoster,
Telcel Settings:
APN: internet.itelcel.com
User: webgprs
Pass: webgprs2002
Domain: <blank>
To stop the message go to Settings-->Connection Setup-->Menu-->Disable Auto Configuration.
Please let me know if it helps.
Regards,
Mario.
perfect i will put my focus on getting the tool to open and then order the screen
what colour was ur connector
Had my Tilt for 1.5 years and I'm actually in a situation where I need some extra cash so I have to part with my phone.
The phone's in great shape, no serious damage. There are some minor scratches on the screen which I've done my best to capture in a picture.
Figure I'd let the community know just in case someone wants to get ahold of one.
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&ssPageName=STRK:MESELX:IT&item=190320560167
is this housing http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=260453968402&ssPageName=ADME:X:RTQ:US:1123 a FURTHER rip-off in quality as the OEM found here http://cgi.ebay.com/OEM-SONY-ERICSS...ries?hash=item2ea6dd8d1e&_trksid=p3286.c0.m14
i want to buy a new housing but i don't wanna buy one with less quality than the original
what are your thoughts on the pics there?
Judging by the pics both fascias seem identical. Although don't know why this big pricing difference. Maybe the first auction is for a replica housing? Don't have large pics as the second auction so we can tell for sure.
Also, at CNN http://cnn.cn/shop/sonyericsson-xperia-c-28_638.html the housings are pricey. For me go for the second auction or buy from CNN, you will be 100% sure that the housing is the OEM.
yeah i was looking at the $24.00 on ebay too... someone should buy it and tell me how it is
i think im gonna let this pass and sell my x1 as it is, im thinking of leaning towards the touch diamond 2 i will miss my keyboard but what the heck
Yo!
I ordered the $24.00 last week... When I receive the housing parts, I will take pictures and spread the message....
Fingers crossed......
Damn the cracks....Its a pity to sacrifice a gd device just now that some gd new things are coming....senseUI....Leo...sure it'll come for d2 too.....but no KeyBoard there.....I have ur very same problem...but I'll try the case !!
Received the housings yesterday.
They're certainly not OEM (maybe the backcover is, the rest not). The outside looks quite nice finished, the set is quite complete (with some tools for the fitting). From the two sets I ordered, one has a large gluestain on the top part of the housing (below the LCD). This gluestain damaged the paint. So I decided to start transferring the phone in the other housing.
After dissecting the phone I started with the assembly of the screen part. The speaker fitted not quite nice, so took some feddling to get mounted. At last it fitted (the print on top of the speaker fitted just). Closing the top part of the housing was a mess. The snap-locks didn't snap (partly) and on one side the housing did not flush fit. The (original) screws did not fit in the thread bushings.... With some fiddling I sort of managed to fit them. Then on with the bottom part. The new chrome buttons do not fit in the new chrome housing part.......
This is were I give up for yesterday. I think I'm going to rebuild the old housing en give up on the new one....
So.....
Decide for yourself if it's worth the trouble.... The housing looks quit neat (not as good as OEM though) but the fitment process is quite troublesome. Delivery was fast and the package is complete (including self-adhesive rubber for screen and speaker fitment). I will get in touch with the guy from Ebay with my findings.... Maybe I'm doing something wrong....
Will post some pictures tomorrow or something....
thnx ur comments were of gr8 benefit to me.....will be gladly w8ing for the pics !
thnx, ur comment were of gr8 benefit to me.....will be gladly w8ing for the pics !
thnx dude, im waiting on mine to be delivered,
looking forward for more reactions...
@Fliptil
From a scale from 0-10, how hard was it to do?
Before starting myself, I want to know if i'm capable of doing this.
To be honest, I know how to fix stuff, but don't know if I can do this trick..
Thanks for sharing anyway
Does anybody know, where i can buy a non branded battery cover for my sliver x1?
It is branded with T-Mobile, but i would like to have it blank or non-branded.
An original one is 25 € in ebay Germany. That's too much. So a cheap one would be fine.
Thanks in advice for all tips!
Best regards
Jog
ebay dude, i purchased one 2 weeks ago for about 10 GBP
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=170363212269
OK guys....
I managed to revive the Xperia tonight.... It has become a hybrid with the metal (original) front and black backside. The middle part is also left original. So the only part I ended up exchanging has been the back cover.
First of all; kudo's to HTC for making the Xperia somewhat sturdy (at least the inside is...). The amount of mechanical havoc tha has been put through the innards of the phone are substantial... And still everything functions!!
After the initial assembly attempt a few weeks ago, I was sure that I had wrecked my phone trying to assemble it with the new housing. Some parts did not fit really well, and the (original) screws did not quite fit the (new) threaded bushings. Halfway through the assembly process I ran into the new chrome buttons not fitting in the new chrome middle part and I gave up on assembly for the time being. After recharging myself for a couple of weeks I forced myself to take up the task of finishing the assembly of the phone tonight...
First I had to disassemble the phone (I was halfway assembling it...) again. I decided to use the original front (had some scratch damage and a very small crack) to surpass the not-fitting thread bushings in the new part. This was a problem... One of the screws had settled in the not-fitting thread bushing and decided to not unscrew, but turn the bushing in the plastic instead. After trying careful and not damaging anything for some time I decided it was time for the hobby knife and screwdriver (as crowbar...). The new front cover did not survive this operation. The screw and the innards of the phone did however!! Reassembly using the old front cover was quite easy, as was reassembly of the back using the original middle part. In the new back part was the thread bushing missing for fixation of the speaker... I used the not-fitting bushing from the front cover as bushing for the speaker fixation. Off course after I made the bushing fitting by forcing the screw in the bushing using a sturdy screwdriver and a set of pliers. This bushing was hammered (carefully...) into the location where the bushing should have been.... This sort of worked. The new back cover does not fit as neat into the original middle part as the original back cover, but it did fit (with some force). The plastic lip that fixes the SIM card was a bit to long, so I had to cut of 0,5mm to make it fit the SIM card. And last but not least only one of the two new battery covers was able to get a grip on the phone...
Then came the thrilling moment to switch on the phone.... Everything worked as if nothing had happened!! So end good all good; I have a phone that looks quite neat (part brushed metal - part black) and functions.
If it was worth the hassle... I doubt it... When you've got a phone that is in pieces and you want spare parts to repair it (as cheap as possible and you like some hobbying) then go ahead and buy this housing. If you want a phone that looks as good as new (and you don't want to risk a heart attack or nervous break down) then I guess you're better off leaving this housing as it is.... For a phone that's worth a few hundred bucks I think this housing is not OK. For a scrapheap phone that needs revitalisation for a small amount of money than it's OK.... If I had to do it all again I think I would have gone for an OEM housing.... After all, I'm happy that my phone functions again so I can leave the TYTN at home. I was to stubborn to buy another housing...
This has become quite a story, hope it will be of any help to somebody. Now I must see if I can post some images....
Grreetz,
Ronald
Some pictures.... try if it works....
Hmm i've dropped my poor x1 on the concrete sidewalk as i got out of my car.
Amazingly it must be good quality because there are a only a couple of scratches on the front and some damage on the rubber around where the
stylus is, but otherwise everything works and is functional.
What this experience did, was got me lookin for spare parts in case I'd
ever need them. As a result I ordered from the same person on eBay 2 days ago
and I just now found this post. Needless to say, I'm damn scared that I've
wasted the money. You tried to fit the black parts on a silver X1, and mine is black,
so I'm crossing my fingers that for some unknown odd fantastical reason, it fits better on the black version. Also may ask whether your model is an x1i or x1a?
I'm guessing b/c its silver its an x1i but u can nvr be to sure. As for me, mine is
a black x1a. I'll post back if i have any updates.
Hi Nick.
I've got a X1i, as you had already guessed.... The mixing of the parts is also a bit of a risk.... The chrome middle part (original) has suffered some damages during my disassembly actions to start with... And has developed some new cracks in the use as a hybrid. Maybe I've overtightened some screws, or maybe the bottom part does not fit well enough so it develops to much tension I don't know...
I've decided to use the X1 till it dies, and to buy something else (no slide keyboard) a little bit more sturdy when it does. I am not going to do any repairwork on it. The design is simply flawed, I have had it repaired at SE once, when it came back it was broken again within two months. These stories can be found al over the internet, so I am not going to repair it again (just to get it broken again). I am not careful enough for a phone like this (however, my colleague also has a X1 that's broken and he is very careful...) I guess.
Just my two cents.
thanks fliptil I'll keep those things in mind.
Before i dropped my x1 for the first time. There was some kind of defect in the silver middle part. At first it was a slight crack so i thought nothing of it, until a piece fell right out of it. Until now i've never needed to go through the process
of getting something fixed and was my experience painful. I got mine through a carrier (Rogers) so I called them on the phone. I was on hold forever, and when I finally got through they told me I had to go to a rogers store to have someone
personally take a look at it.
I got to the store, got on their phone, and was on hold for 20 minutes. When I got through they told me they would connect me to a specific department.
Another 20 minute wait.
I got through and then gave the phone to a rogers employee there. He confirmed that it should be a defect as there were no signs of dropping it and then HE waited 20 minutes while the guy on the line called sony.
I waited all that time to find out that I cannot get it replaced through my carrier but had to go through sony themselves.
I looked up some stories of experiences with SE's services and found that most (if not all) of the time they replace your x1 with a refurbished one, and I wasn't about to trade a perfectly brand new one with a minor ding in it, for
one that could be potentially scratched up and badly treated.
Now that I've dropped it though I fear that whether the defect gets worse or not I cannot get Sony's warranty on it. However, after what you've just told me I don't think I want to. Here's to hoping that i won't have to do x1
surgery anytime soon...
hi everyone so i managed to break my hd2s screen yeah i know it sucks.. right now im in the process of changing the digitizer for a new one i bought off of ebay.. i took the phone apart that was pretty simple but while doing so i removed many glue copper like stickers and also adhesive strips specially the one holding the digitizer and the lcd together.. my question is if anybody knows where i can buy the adhesive strips.. and most important the cooper like tape since it was covering the sides and the back part where the battery goes.. has anyone been successful at fixing their broken hd2 and is the copper-like tape important.. or can i just use some regular hot temperature resistant tape? well thanks in advance for the help
I know this doesn't really help you with your situation in any way but. I broke mine as well, and i just decided to let the insurance company handle it. I know it's expensive 130$ compared to the 50$ you could buy a new screen for. But they send you a brand new sealed in box phone, next day air shipping. I've only seen one video on how to replace the glass, and it was for the euro one, and it required, basically, completely disassembling the entire phone.
Sorry for the non-help. Just my .02c
i broke the one on my blackstone bought one off ebay pretty cheap but i couldn't put it together ,i ended up paying $50 get it installed the right way
Hi, I recently got my HTC One (m7 / at&t) as a graduation present in June. Unfortunately I recently dropped it face down without its case onto the ground and resulted in a large crack(s) on the screen. I can still use the device, text, talk, watch videos etc.. but as you can obviously tell one does not simply enjoy the pleasure of having their phone(s) screen cracked.
So I immediately began looking for a solution and repair shops said 300$ to fix when I purchased my phone for just a little over 300$. So that is out of the question, unless its truely my last resort. So I began looking on how to fix it, youtube failed me the only thing that was helpful were the breakdown videos of the HTC One teaching me how to take apart the phone (The only part I was interested in was on taking out the glass).
The only solution I currently can think of would to repair it myself. So here are my questions.
1) The screen is cracked only, the touch screen works fine etc.. so can someone show me the listing on ebay/amazing (I prefer amazon) of the kit or things I would need to fix it.
I Saw this one:
amazon /HTC-M7-screen-digitizer-replacement/dp/B00CWKGZ5U/ref=sr_1_5?ie=UTF8&qid=1376517625&sr=8-5&keywords=HTC+One+Glass
Because it looks like exactly what I Need, BUT I'm no expert so would that fix my problem? Or is it the wrong thing since all I need is the glass and thats the "Digitizer Outter Glass" or something? I dont know my terms that well but to me it seems like what I need because its the "Outter Glass" haha.
But I'm confused about that because it says Digitizer outter glass and in the picture has the connection cord thing, Would this be replacing every part having to deal with the screen? (i.e I take a suction cup and take out the screen, and unplug the connection from the phone to the screen, would what I having in my phone (cracked screen with cord..) be the same thing as what Ill be ordering from that amazon thing but NOT cracked?)
-----------
2) How would I replace it step by step? I already seen videos of taking the phone apart and replacing iPhone screens but I havent seen any towards the HTC One in regards to replacing the screen. So would someone mind pointing me in the right direction, or giving me a text tutorial on what to do? I can pretty much figure it out by reading it since I have videos n pictures to compare it to sorta.
-----------
3) I never done a repair before but it doesnt seem that hard, just have to be gentle and know what youre doing (Thus why im asking so many questions), is this my best option? Or what should I do...
-----------
4) When I seen videos regarding the iPhone screen replacement it was showing things like Screen Seal / and him literally taking off the glass from the this other thing and replacing just the glass itself instead of the thing below it.
Would I have to also use a type of screen seal / or have to take glass off like you would do in the iPhone or is it a 100% different conecpt / idea?
----------
Remember: I basically need to know what I need to fix the cracked screen of my phone, I think this is what i need:
amazon /HTC-M7-screen-digitizer-replacement/dp/B00CWKGZ5U/ref=sr_1_5?ie=UTF8&qid=1376517625&sr=8-5&keywords=HTC+One+Glass
So if it is, then may someone tell me how to replace my phones cracked screen using that and explain it to me what im actually doing and watch each part is etc.. (like what im buying and whats cracked with my phone, so I know its what I need)
and if not, can someone tell me what I need and how to do it?
PS I understand I cant post outside links, but its amazon and Im not trying to advertise i just need the link as a comparison / example
This is one of the worst phones created when it comes to repair. It is well made, but ease of repair was not their priority. The only thing I can recommend to you would be to go to the Ifixit web site. They do a tear down of the phone to show how hard it is to repair. Maybe that will help you out.
Edit: In your original post, you wrote that you had watched videos on the Iphone. Since this is a different phone with differences in assembly, I suggested a video concerning this specific phone. Not trying to be rude, but if I was taking apart my HTC, I would view specific videos concerning my phone. I thought that the specific video might give you clues as to the parts involved in assembly and what procedures were necessary. The video I was referring to concerned their taking apart an HTC One. Every bit of information might be helpful to you trying to fix your problem.
Wolf said:
This is one of the worst phones created when it comes to repair. It is well made, but ease of repair was not their priority. The only thing I can recommend to you would be to go to the Ifixit web site. They do a tear down of the phone to show how hard it is to repair. Maybe that will help you out.
Click to expand...
Click to collapse
Not being rude but I'm pretty sure I already stated the fact that I seen the videos and tutorials regarding the tear down of the phone. So how do you expect that to "maybe" help me out? If I'm trying ti find out the part(s) I need to replace since I don't know the full termology.
I know how to take my phone apart (For the most part), I Just need to know mainly what I need to replace to fix my cracked screen, or whats my best solution. + The questions i stated in the thread.
Thank you.
Unfortunately you will have to change the whole screen assembly.
This will cost you a little ... http://www.etradesupply.com/oem-htc...itizer-assembly-with-front-housing-white.html
You could try also just the LCD+ digitizer (if the front aluminum parts are still intact: http://www.etradesupply.com/oem-htc-one-lcd-screen-and-digitizer-assembly.html
If you scratched the back of the phone, those guys have the back assembly also ... about 24 USD ... ( http://www.etradesupply.com/oem-htc-one-rear-housing.html )
You could TRY replacing only the digitizer ( http://www.etradesupply.com/oem-htc-one-digitizer-touch-screen.html ) but I would not go there. In between the digitizer (what is actually cracked in your case) and the lcd there is a special "jelly" glue which is VERY hard to remove w/o breaking the LCD. I tried that on a N7 and now I'm waiting for a new LCD to be delivered ...
Good luck!
Thank you, I appreciate the reply.
My casing / housing isnt broken (The cracks start from the top of the screen right below the camera/speakers where the glass is, and the crack(s) end towards the HTC Logo etc..) so should I still buy the white housing with lcd+digitizer or should I just go with the second option and buy the digitizer+lcd without the housing (second link you gave me)
JohnVerde said:
Thank you, I appreciate the reply.
My casing / housing isnt broken (The cracks start from the top of the screen right below the camera/speakers where the glass is, and the crack(s) end towards the HTC Logo etc..) so should I still buy the white housing with lcd+digitizer or should I just go with the second option and buy the digitizer+lcd without the housing (second link you gave me)
Click to expand...
Click to collapse
Let us know how it went. :good:
Not sure if it's worth it. HTC will fix it for you somewhere around $180.
Sent from my HTC One using xda app-developers app
JohnVerde said:
Hi, I recently got my HTC One (m7 / at&t) as a graduation present in June. Unfortunately I recently dropped it face down without its case onto the ground and resulted in a large crack(s) on the screen. I can still use the device, text, talk, watch videos etc.. but as you can obviously tell one does not simply enjoy the pleasure of having their phone(s) screen cracked.
Click to expand...
Click to collapse
Hi,
I posted a lengthy thread on how to do a repair here
http://forum.xda-developers.com/showthread.php?t=2387992
Did it well over a month ago and it is still running fine.
You might want to call you household insurance, and tell them someone in your household (not you) dropped the phone while cleaning for example.
Here in the Netherlands, they will pay the repair even the same day.
I didn't had to send them anything, just tell them on the phone how much the reparations would cost, and they transfered the complete numeber right away!
Too bad I found that out after spending more than $100,- on phone reparations.
It might be worth the shot, since they may reimburse it for you.