Related
Device Information:
ROM version: 1.56.421.1
ROM date: 10/26/07
Radio version: 1.27.15.32
Protocol version: 22.51.88.13H
Phone does not charge from USB port under certain conditions. This happens when the phone is used to connect to the internet (Internet Sharing).
The charge indicator will show that the battery is charging when the phone is first connected to the USB port.
It will still show charging when Internet Sharing is activated and connected.
After a while (I have not managed to establish how long) the charge indicator goes away and the battery drains as if it was not connected to a charger. The drainage also seems to occur quickly (again I have not managed to quantify this).
Unplugging the USB cable and then reconnecting it does not start the charging process again. The phone has to be reset and then reconnected to the USB port for the charge indicator to show again.
Your help will be most appreciated.
i've noticed that it will stop charging when it overheats......esp when doing internet sharing using wmwifirouter. my solution is to take off the battery cover, and place it next to a fan. not the best solution, but it works
You should be grateful, my Kaiser chargers me every day!!!
so how's the solusion then?
morizq said:
so how's the solusion then?
Click to expand...
Click to collapse
check your pins at the USB port.
maybe some pin is ~
get same problem when using tomtom for more tghan an hour. make long car journeys hard. solution : turn on the AC hold battery and phone to it for a time and things start working again.... its an overheating problem for me
I've also had charging issues, my light would be on but it wouldn't actually charge then randomly i plugged it into my 360 and it charges perfectly....im guessing after awhile it requires a higher voltage to charge...so try a 360 or computer hope i was a help
hey ya'll, so for the longest time when I would plug the tilt into the wall charger, the screen would NOT turn on (it would not wake up) - however, suddenly, now it does...
I've tried going through all the settings, but I can't seem to figure out how to get it to not wake up when plugged in (wall charger) -- I know it will turn on when plugged into the computer, that's fine -- any help, as always, would be greatly appreciated
thanks!
Well I'm not sure how to stop it from waking when you plug it in, but you can always tell it to go right back into stand-by.
Check out the settings in Start > Settings > System [tab] > Power > Advanced [tab]
You can tell it to "Turn off device if not used for" X amount of time while "On external power".
Not a fix but I hope it helps.
It's a strange thing. I have both a wall charger and a desktop cradle/charger.
When I plug my Tilt into the desktop cradle (without the usb cable connected to the pc), it turns on. But, when I use the wall charger, it doesn't.
This is very consistant. Maybe the pinout is different between the connectors, or the output voltage is different.
It's just something I've gotten used to and can live with.
The Tilt will not wake if you use the wall charger that came with the Tilt. It will wake if you use other types of usb charger
replay37 said:
The Tilt will not wake if you use the wall charger that came with the Tilt. It will wake if you use other types of usb charger
Click to expand...
Click to collapse
I've noticed that myself and I think it is extremely odd but intelligent.
If your cradle is connected to a PC via USB then it will wake. My Tilt never wakes when I simply plug into the charger, but dropping it into my cradle wakes the PPC and the PC (if it happens to be asleep).
It wakes because there is a sync notification that tells it to on detection of a USB ie. repllog.exe is by default set to run when this key is present "AppRunAtRs232Detect"
Now you can remove this repllog entry, but it means you would have to run repllog manually every time you want to sync.
The following was written for the purpose of replacing repllog entries deleted by mistake. However it will give you some info on what happens when you connect certain Rs232 USB connectors.
http://michael-channon.spaces.live....artqs=cat=Repairing+the+ActiveSync+Connection
Mike
I am using the supplied wall charger that came with the phone and the screen powers on when I plug it in. It used to not do this at one point. I believe some thrid party software I installed is causing this. Also the screen with turn on once the charge is complete. Very annoying at night. I don't want to use the on external power settings to blank the screen after x minutes because this messes with using the GPS function while in my car. I want to see the screen while using GPS and plugged into a power source.
dalavar said:
. I don't want to use the on external power settings to blank the screen after x minutes because this messes with using the GPS function while in my car.
Click to expand...
Click to collapse
It shouldn't, all GPS programs I've tried force backlight on regardless on the system settings while they're running. Which one are you using?
I'm using iGuidance 3.1.
I had to do a hard reset due to an app I installed making my phone go all wonky. After the hard reset and re-installing all my programs I no longer have this problem of the phone waking on external power.
My original Tilt used to do the same thing - screen turned on when plugging into the HTC supplied power cord (even after a H/R with no programs). Eventually, the phone had to be replaced after one day it had a red light after charging a few hours and wouldn't turn on (it had been around 50% when plugged in). My refurbished Tilt mostly does not power on when plugged into the wall charger. Once in a blue moon, it will. It is random enough, I haven't been able to see a common factor as to why.
Any settings to disable wake on USB to computer connection?
A lot of times I plug my Kaiser to PC just to charge it, and I hate to see it connecting every time.
Many thanks!!!
Hi!
I have a strange problem: sometimes when I connect the charger (mains outlet) to the Diamond it does not charge. Sometimes it it also does not indicate that the power is plugged in, other times it indicates charging but the battery level does not increase.
If I go to battery settings, tick then untick the checkbox "Do not charge when USB is..." it suddenly starts to charge but sooner or later the charging stops again.
Soft reset usually helps. Is there any patch for this?
EDIT: I noticed it mostly happens when I use the Diamond as a Bluetooth modem. If I stop the connection it starts to charge. Maybe bluetooth consumes so much power that it cannot get enough from the power adapter?
Honestly, I found I had this exact issue. I was not using any applications though, it was simply a bad charger.
Have you tried to duplicate this with just using a USB cable to PC?
I found out it is due to overheating. I was using the Diamond in my car, plugged into the car charger. However, the device turned itself off and would not charge. It was a hot morning. I put a hat over the phone to prevent the sun from shihing at the phone and directed the air cooler of the car to the phone. After a few minutes it started to charge.
The brand new charger I got with my Diamond was defective, i tried an older usb charger from my TyTN II and its been fine since.
I've read many post where kaiser issues are opposite for what I have.. My htc can connect to activesync with no problem.. but I can charge it no more.. Orange led become up but after a couple of minutes lights is gone.. battery charging icon is up, and charging message is shown but battery keeps going down..
I tried USB-PC cable, Car charger and issue still the same.. yesterday I charged it with wall charger and it worked but i'm affraid it becomes worst..!!
I backed up all my data and did a hard reset.. but still the problem.. Any clue guys..??
my money is on a periodic defect connector where the 5volts and ground connectors don't give a stable consistent connection which is required to charge
as it works one time as the periodic factor
Try looking under Settings - Power - then the advanced tab and looking to see if the do not charge when connected to pc is checked.
This will sometimes keep it from working with third party chargers also.
When I charge my HP Touchpad via either the USB cable or the touchstone dock it will turn itself on after a few minutes displaying the low battery symbol and robot into the default OS. Once in either Android or WebOS it will then open the clock app. Is this normal behaviour? If not then has anyone found a solution?
Thanks
Yeah, its supposed to do that...
Sent from my aokp_tenderloin using xda premium
Ah okay, just thought I'd ask in case it was ruining my battery or something.
ojdon said:
When I charge my HP Touchpad via either the USB cable or the touchstone dock it will turn itself on after a few minutes displaying the low battery symbol and robot into the default OS. Once in either Android or WebOS it will then open the clock app. Is this normal behaviour? If not then has anyone found a solution?
Thanks
Click to expand...
Click to collapse
When I have mine on the Touchstone and power it off it stays off , but if connecting to a charge source while turned off yes it does turn on . Try turning it of while it is still on the touchstone or connected to a power source. I checked mine with a touchstone.
ojdon said:
When I charge my HP Touchpad via either the USB cable or the touchstone dock it will turn itself on after a few minutes displaying the low battery symbol and robot into the default OS. Once in either Android or WebOS it will then open the clock app. Is this normal behaviour? If not then has anyone found a solution?
Thanks
Click to expand...
Click to collapse
It's normal, but once on you can power off and it should stay off while charging.
On earlier versions of the nightly, it used to reboot until powered off, but that problem seems to have been fixed with the recent updates.
Noticed one thing on my CM9 TP... just flashed to CM9 for a day or so... never had problem with the power button menu (Power off, Reboot, Screenshot.. etc) until I plugged it to the charging cable (via A/C -> USB adapter) charging it. Power menu doesn't get call out by holding the power button... anyone?
Mine doesn't turn on while charging if it is charging when I turn it off. If I plug it in, it can randomly restart
I have the same problem...what I did is to connect the charging cable first. then power off the tocuhpad. It stays off and won't reboot during the charging period.