Related
I've been trying to get my old extended rom and new Qtek OS on my Wizard (Vario).
But now it gets stuck in the spash screen (ie the one giving the ROM numbers).
I've tried putting the wizard into bootloader mode and I can flash RUU's but when it resets it still gets stuck on the spash screen and won't go any further !!!????
What can I do ??
Please Help
Cheers
John
I should say that I had flashed using button's ROM RUU_Wizard_1050412_WWE_101_11210_WWE.exe.html
and this worked fine!
I then copied across my T-mobile Extended ROM and again everything seemed OK.
BUT then I tried to restore my new saved OS ROM using aWizard and this caused a freeze on my Wizard. It was after a hard reset that the wizard stopped at the splash screen.
Now of course I'm limited in my options because Activesync won't work until the Wizard has fully booted up.
I have tried setting the Wizard into bootloader mode and tried several ROM's (RUU Installer ones) but every time the correct splash screen comes up with the new ROM numbers but that is as far as it gets.
I also noticed on hard reset that you get the following message
Format FAT partition
Format failed
it then goes to the splash screen as before.
Are there any other things I can try Or will I have to send it back to T-mobile for a replacement??
(It's only 2 months old and I have re-flashed it with the orginal T-mobile ROM - but still won't go past the splash screen!!)
I live in hope
John
I have this EXACT same problem!
I can reflash any ROM but it will not go past the splash screen. Only difference was I wasn't playing with my extended ROM. I flashed the AKU2 QTEK ROM yesterday and have been fine through several soft resets, etc. This last time I was uninstalling phonealarm and after a soft reset I got a "could not find smswakeup.exe" (or something similar) and it's been stuck ever since! I also get the "Format Failed" message. Can anyone help!?
I think I'm going to have to send it back to T-mobile and hope they give me a replacement. Something is wrong, it doesn't seem to make any difference what ROM I used.
I think I'll reload the T-mobile shipped ROM grom the FTP site and send it back - and claim ignorance that it it suddenlt freezed and now won't boot up! - Bummer!!!
Right I've logged a fault and it will be sent back - let's hope T-mobile can't detect it's been unlocked and had several ROM updates - I suspect they will try a ROM update themselves then give up ???
The worrying thing though is that it IS possible to kill your phone with updates - maybe it was when I used aWizard to try and restore a ROM that did it??? I'll be more carefull next time!!
this has just happened to one of the devices im flashing at the moment.... absolulty f**king raging :evil: :evil:
i wish teher was a solution!!? anyone got any ideas?
activesync wont find it, so aWizard wont work.
i can flash between 3 roms without any problems (1.5.x 1.6.x 2.x) but always hangs on the splash screen. i have flashed back to the default rom that it came installed with it so i could just send it back to o2 (only 2 days old!)
i would rather just get it sorted by myself thoough so if anyone has ANY ideas then please let me know.
thank you!
Good luck! after about 3 days of trying different types of firmware, I gave up and sent it to expansys, for repair. And it looks like they've lost the bloody thing now. :evil:
tonym001 said:
Good luck! after about 3 days of trying different types of firmware, I gave up and sent it to expansys, for repair. And it looks like they've lost the bloody thing now. :evil:
Click to expand...
Click to collapse
yup looks like i might have to give up... ohwell, no worries i will just return it back to O2...
looks like one of our sales guys wont be getting a new phone on tuesday :lol:
same problem here.
tryed to write os with awizzard after changing extended_rom.
kills phone.
format failed..
Tryed different os's from win util - failed
upgraded with sd card methode worked.
in short :
you need a working wizzard to make a os dump on sd card.
Connect to wizzard with usbterm or romupdate.exe or simular.
do a rs2all command to dump os to sd card.
stick this card in broken phone.
hold voice comm button while resetting.
On ask press voice comm button again.
it bow restores the sd backup to phone.
saved mine.....
btw sd card backup can be read ad write by pc with util ntrw.exe .
so if you don't have a working dump i can upload one.
just mail me.
grtx , arnold
hard reset your device and hold your Camera Button prior to starting the wizard back on.
when the device turns back on, you will get the boot screen. Plug in your USB cable and load one of the known ROMS like the second to last iMate ROM.
This will allow you to get past the splash screen.
FarSeide said:
hard reset your device and hold your Camera Button prior to starting the wizard back on.
when the device turns back on, you will get the boot screen. Plug in your USB cable and load one of the known ROMS like the second to last iMate ROM.
This will allow you to get past the splash screen.
Click to expand...
Click to collapse
this didn't work for me.
couls flash rom. even splash screen changed to new roms one.
but still stuck at splash...
tried it with about 4 different orgigenal roms
grtx arnold
arnoldl said:
FarSeide said:
hard reset your device and hold your Camera Button prior to starting the wizard back on.
when the device turns back on, you will get the boot screen. Plug in your USB cable and load one of the known ROMS like the second to last iMate ROM.
This will allow you to get past the splash screen.
Click to expand...
Click to collapse
this didn't work for me.
couls flash rom. even splash screen changed to new roms one.
but still stuck at splash...
tried it with about 4 different orgigenal roms
grtx arnold
Click to expand...
Click to collapse
Don't worry, I met the same problem as you before, almost lost my hope, but finally I managed to fix it.
The solution is simple, that is to find an original SD card backup image from your wizard or others, then try to restore it in the bootloader mode. In my case, it said checksum error or sth else after begin restoring, and it gave up. Then I put my wizard into bootloader mode, picked one offical released RUU package, start reflash again. Finnally, I found the wirzrd works again for me after reboot.
I guess the principle is that the SD restore will destroy some import flash data structure before it said wrong, then the RUU package will rebuilt it wholely in the next reflash.
Hope this helpful, and sorry for my bad english.
There is hope
Last week after trying to downgrade to the original Cingular ROM on my 8125 using aWizard I ended up with a device that was close to being a paperweight. At least I thought so until I read and read and finally was able to get it to the bootloader and then plugged in the USB cable and ran the RUU for the new Qtek ROM (2.17). Guess what happened, yeah it worked. To my surprise I had a perfect device after 15 minutes.
For about 3 hours I thought I was a toast. Never will I do that again.
THIS is truly heaven for me !!
I have my O2 XDA MINI S locked on the splash screen .. and i updated some ROMS to it ....BUT IT DOESNT GET THROUGH IT .... please tell me what to do in a little detailed manner .. please so that i can get my phone to work.. there is no warranty on the phone and i stay IN INDIA . SO YOU'LL ARE MY ONLY HOPE .
my email id is - [email protected]
If you have a dump of the O2 XDA MINI S ..please mail it to me
Plese tell me what to do next ? WILL TRULY APPRECIATE HELP
PLEASE SOME ONE ATLEAST MAIL ME the dump of the os SO THAT I CAN TRY THE SD CARD UPGRADING ,.,,, O2 XDA MINI S
Re: There is hope
Dear Friend
I have problem that my xda mini s stuck on O2 screen, could you help me step by step.
Thank you so much
my mail : [email protected]
Thanks friend
hellomoto_25 said:
Last week after trying to downgrade to the original Cingular ROM on my 8125 using aWizard I ended up with a device that was close to being a paperweight. At least I thought so until I read and read and finally was able to get it to the bootloader and then plugged in the USB cable and ran the RUU for the new Qtek ROM (2.17). Guess what happened, yeah it worked. To my surprise I had a perfect device after 15 minutes.
For about 3 hours I thought I was a toast. Never will I do that again.
Click to expand...
Click to collapse
Dear Friend
I have problem that my xda mini s stuck on O2 screen, could you help me step by step.
Thank you so much
my mail : [email protected]
Thanks friend
odyseus said:
I've been trying to get my old extended rom and new Qtek OS on my Wizard (Vario).
But now it gets stuck in the spash screen (ie the one giving the ROM numbers).
I've tried putting the wizard into bootloader mode and I can flash RUU's but when it resets it still gets stuck on the spash screen and won't go any further !!!????
What can I do ??
Please Help
Cheers
John
Click to expand...
Click to collapse
stuck on o2 screen helppp
Dear Friend
I have problem that my xda mini s stuck on O2 screen, could you help me step by step.I see alot of post, so complicated
Thank you so much
my mail : [email protected]
Thanks friend
flexchen said:
arnoldl said:
FarSeide said:
hard reset your device and hold your Camera Button prior to starting the wizard back on.
when the device turns back on, you will get the boot screen. Plug in your USB cable and load one of the known ROMS like the second to last iMate ROM.
This will allow you to get past the splash screen.
Click to expand...
Click to collapse
this didn't work for me.
couls flash rom. even splash screen changed to new roms one.
but still stuck at splash...
tried it with about 4 different orgigenal roms
grtx arnold
Click to expand...
Click to collapse
Don't worry, I met the same problem as you before, almost lost my hope, but finally I managed to fix it.
The solution is simple, that is to find an original SD card backup image from your wizard or others, then try to restore it in the bootloader mode. In my case, it said checksum error or sth else after begin restoring, and it gave up. Then I put my wizard into bootloader mode, picked one offical released RUU package, start reflash again. Finnally, I found the wirzrd works again for me after reboot.
I guess the principle is that the SD restore will destroy some import flash data structure before it said wrong, then the RUU package will rebuilt it wholely in the next reflash.
Hope this helpful, and sorry for my bad english.
Click to expand...
Click to collapse
how to use bootloader
could you tell me how to use mentioned bootloader for restoring the images? where can I get the software?
Please help
Hendrick
flexchen said:
arnoldl said:
FarSeide said:
hard reset your device and hold your Camera Button prior to starting the wizard back on.
when the device turns back on, you will get the boot screen. Plug in your USB cable and load one of the known ROMS like the second to last iMate ROM.
This will allow you to get past the splash screen.
Click to expand...
Click to collapse
this didn't work for me.
couls flash rom. even splash screen changed to new roms one.
but still stuck at splash...
tried it with about 4 different orgigenal roms
grtx arnold
Click to expand...
Click to collapse
Don't worry, I met the same problem as you before, almost lost my hope, but finally I managed to fix it.
The solution is simple, that is to find an original SD card backup image from your wizard or others, then try to restore it in the bootloader mode. In my case, it said checksum error or sth else after begin restoring, and it gave up. Then I put my wizard into bootloader mode, picked one offical released RUU package, start reflash again. Finnally, I found the wirzrd works again for me after reboot.
I guess the principle is that the SD restore will destroy some import flash data structure before it said wrong, then the RUU package will rebuilt it wholely in the next reflash.
Hope this helpful, and sorry for my bad english.
Click to expand...
Click to collapse
Hi Arnold
My O2 cda mini s get stuck at splash scree, I read your post, still not so understand how to solve it, could you be so kind to write me step by step, and send me some software to solve it. Your help will be so much appreciated.
Hendrick
Email: [email protected]
arnoldl said:
same problem here.
tryed to write os with awizzard after changing extended_rom.
kills phone.
format failed..
Tryed different os's from win util - failed
upgraded with sd card methode worked.
in short :
you need a working wizzard to make a os dump on sd card.
Connect to wizzard with usbterm or romupdate.exe or simular.
do a rs2all command to dump os to sd card.
stick this card in broken phone.
hold voice comm button while resetting.
On ask press voice comm button again.
it bow restores the sd backup to phone.
saved mine.....
btw sd card backup can be read ad write by pc with util ntrw.exe .
so if you don't have a working dump i can upload one.
just mail me.
grtx , arnold
Click to expand...
Click to collapse
Hello all,
first, a big thanks to all the rom developers around. You transformed my Diamond in a usable and enjoyable tool.
What happened to me tonight is very frightening. In fact, I cannot believe what happened.
And this is the story: I was at a birthday party and later in the evening I checked my phone : it seemed to have frozen, so I rebooted it as I do sometimes when I have no other choice. But this time something strange happened : I got the following message "this concludes the beta test of this software release. thank you very much for your time and effort in helping make this a great product for our customers" - what the ... ? No way to make a call, the message is impossible to remove... completely blocked !!!
I don't remember exactly the rom I flashed last because I sometimes change. It might be a dutty's release (75%M sure) - anyway I was in a very bad situation because my wife wasn't feeling well and I couldn't call her without finally borrowing a phone from someone.
I will flash a new rom tomorrow and I hope that the message will disappear but I can tell you that it is a very strange feeling when suddenly your phone refuses to operate normally. It's a nightmare.
I hope that someone has an explanation for this because I don't want to go trough this situation ever again, it's just so annoying to have a phone which tells you "No you can't use me; your trial period has expired" when you need it he most.
Thank you for your opinions in advance
Have you tried a hard reset?
Yep same problem here.
Using duttys 1.93 - Can't get to his website either.
Hard rest does not work - had to reflash back to branded (Telstra) ROM
i'm having the exact problem right now, what can i do to fix this? someone told me to reflash it but how? i'm VERY new to the diamond
hardreset does not work
I bought the phone from a person so it's second hand. The seller did mention he updated the ROM, I'm assuming this is the cause of the problem? help please
thanks!
I am getting the exact same problem.I do not know what to do.
Sigh and since my computer will not sync, I cannot reflash it. Hard set is also a no go.
ya I cant sync it with my computer either... i'm searching other sections on this forum and I cant seem to find one that teaches you how to flash without syncing with the computer
OK i got it well kinda sorta. If you hard reset and just use the date taht dutty had then your phone will load. Do not correct the date and you should also change the date on your computer so that it wont sync. Then donwload his new rom or whatever rom you prefer and then flash it. Then change the dates back. It worked for me.
thanks.. do you have the link for the new rom?
I'm going to give it a try
The link it dutt'y new rom is here http://rapidshare.com/files/162091111/Ruu_Signed_duttys_diamond__V2.9_5_2_20275_RTM_Full_MSVC.zip
just a question how do you flash it?
can you help me? i'm very new to this phone
I had the same problem last night- expired beta software. If I do a hard reset I believe I will loose all the info on the phone, is that correct?
I was thinking that changing the date will work, is there another way to change the date without having to loose the info?
Someone has a reliable link to an instruction on how to flash the ROM?
I am also using throy 2.3, to find the latest release please go to WWW.DUTTYTHROY.NET
Any help appreciated.
!everyone! you can flash roms from bootloader. hold volume down and the little red reset button, keep holding vol down untill bootloader. at the tri color screen, run ruu from host pc. everything will be fine with this method. just like activesync.
ok i to change the time and stuff and it actually can sync using active sync.. however.. when tried to install HSPL 1.24 after the part where the phone will turn black.. i click on the DiamondCustomRUU as instructed
but it says this "The application failed to initialize properly (0xc0000135). CLick on OK to terminate the application"
Is there a way I can recover this without losing all that is on my phone?
Do anybody know the password for the latest ROM 2.9 from Dutty? His page is unavailable right now....
Duttys V2.9 RTM Finale
someone please tell me how to flash.. from scratch? i hard reset my phone.. and i cant get HSPL to work. When i install the activesync way, the black screen turns on then i cant open DiamondCustomRUU
if i do i the bootloader way, when i connect from the three colour screen it cant pick up the phone because it says i'm missing Qualcomm CDMA Technologies MSM
please help been stuck for hours already
i won't flash Duttys ROM again!!! Right now i need my phone and it doesn't work! And if i reflash it i lose my data....
never again!
its you have a problem with duttys rom
you need to use his thread to point out your problems....
not this one.
Sorry if I shouldn't be writing a new thread about this, but I couldn't find a thread about bad flashes...
I'm a newbie with this, and I think I just bricked my phone after only my second flash I have a Touch Pro 2 (T-Mobile), and I was able to successfully install HardSPL. I even flashed the EnergyROM LEO with no problems. After a few days of playing around, I tried to flash the AthineOS v2.0 ROM, and now my phone won't boot up... it gets stuck in the Touch Pro 2 black screen with the red lettered version numbers at the bottom. I tried rebooting and pulling the battery out, but I have had no success in being able to boot it back up.
Any ideas on how I can fix this? This sucks I've only had the thing for less than a month...
localcall001 said:
Sorry if I shouldn't be writing a new thread about this, but I couldn't find a thread about bad flashes...
I'm a newbie with this, and I think I just bricked my phone after only my second flash I have a Touch Pro 2 (T-Mobile), and I was able to successfully install HardSPL. I even flashed the EnergyROM LEO with no problems. After a few days of playing around, I tried to flash the AthineOS v2.0 ROM, and now my phone won't boot up... it gets stuck in the Touch Pro 2 black screen with the red lettered version numbers at the bottom. I tried rebooting and pulling the battery out, but I have had no success in being able to boot it back up.
Any ideas on how I can fix this? This sucks I've only had the thing for less than a month...
Click to expand...
Click to collapse
hi if you have done the hardspl then try this
to enter Bootloader
Remove the back cover from the phone.
Hold the Volume Down button.
Use the stylus to press the reset hole.
Or if the device was powered off, press the power button whilst holding down the Volume Down button.
you should see serial at the bottom of the three color screen then plug in the usb cable the serial should change to USB then just flash another rom.
i hope this helps you.
Thank you! Thank you! Thank you! Thank you! That worked! That's a really cool recovery feature from HardSPL... you guys really know what you're doing This is such a huge relief...
localcall001 said:
Thank you! Thank you! Thank you! Thank you! That worked! That's a really cool recovery feature from HardSPL... you guys really know what you're doing This is such a huge relief...
Click to expand...
Click to collapse
only to pleased to help I am glad you got your phone back working
localcall001 said:
Thank you! Thank you! Thank you! Thank you! That worked! That's a really cool recovery feature from HardSPL... you guys really know what you're doing This is such a huge relief...
Click to expand...
Click to collapse
hehehe finally you found solution.. but my rom does not have any problem.. somethings goes wrong
b16b said:
hehehe finally you found solution.. but my rom does not have any problem.. somethings goes wrong
Click to expand...
Click to collapse
idd, this is not ROM related, its just unlucky like hell. See the phone as a PC, where blocks need be written. If a block fails or is corrupt, you get these jokes. Its like a BSOD on a Windows PC.
I gotta admit it is great knowing that once you've done a hardspl you are safe as houses as even if you flashed the most currupted ROM, the bootloader will always allow a reflash.
This is way more stable and safe than any other experience I've had of phone flashing.
b16b said:
hehehe finally you found solution.. but my rom does not have any problem.. somethings goes wrong
Click to expand...
Click to collapse
Funny that, your latest ROM was the only one I had problems with - the same problems as the original poster, in fact. I flashed a different ROM fine, re-downloaded your 2.0 and flashed it again, same problem. Hanging on the boot screen.
b16b said:
hehehe finally you found solution.. but my rom does not have any problem.. somethings goes wrong
Click to expand...
Click to collapse
Probably I think I was just unlucky. My fear (while I was panicking) was that your ROM is European based, and since mine came from T-Mobile, it didn't mesh well. I also didn't unlock my phone so that could be also be a problem...
awesome community
localcall001 said:
That's a really cool recovery feature from HardSPL...
Click to expand...
Click to collapse
well..this is a normal recovery feature for stock spl also
Same Issue
I had the same issue with AthineOS v2.0 ROM it gets stuck on Touch Pro 2 logo
wahida76 said:
I had the same issue with AthineOS v2.0 ROM it gets stuck on Touch Pro 2 logo
Click to expand...
Click to collapse
no one have told me that on my thread... only here i found this issue.. and finally how pass the problem?
I had to re-flash a different ROM.
I'm wondering if it's related to the radio version...
what is your version of radio
can't you flash the latest 23060?
i use radio 3.36
I've used 4.49.25.05 and have just got the same result on 4.49.25.17
I'll try flashing 3.44.25.27 (the oldest in the radio thread) and re-flashing your ROM.
Alas, no luck with that one either.
I have no idea why it doesn't seem to work on my Rhodium :/
I'm sorry if I'm hijacking this thread but it's the only one I've found that's even close to having the same issue I have, though I'm still using the stock rom/os.
I was installing winmo msn messenger. It installed fine and reset my tp2 fine. It goes thru the tp2 splash screen, the verizon splash screen and the winmo splash screen. Then it shows owner information and this is where it gets screwed up. Owner info will stay up forever if I dont touch the screen. After touching the screen the only thing left will be the top bar and the rest of the screen stays black. The only things on the top bar are the signal icon (which always has an x), the wifi icon (which seems to be connected fine lol) and either owner info will still be in the upper left or the start menu will be there. Hitting the screen only causes my tp2 to beep.
Nothing I know how to do (which is basically just hard and soft resetting it) works. Verizon can't fix it (didnt think they would be able to) and I can find no drivers (possibly cause I'm still a noob with winmo) to resolve my issue. I'm not even sure how I'd get them on as it wont even sync up to my computer and my computer cannot find its hd. If I could get a rom for the verizon one I think I can figure it out from there with no issues...but htc website sends me to verizon website for support and vice versa. The htc wiki is the closest I've gotten to an answer...but no rom to download. The only OEM roms I can find anywhere aren't for this phone, unless one of those will work? You guys are the experts.
Does anyone know what I can try? Verizon wants me to return it but cannot tell me when I'll get my new one as they are out of stock...again. Please help lol! Thanks for any and all help.
Mr.Clark said:
I've used 4.49.25.05 and have just got the same result on 4.49.25.17
I'll try flashing 3.44.25.27 (the oldest in the radio thread) and re-flashing your ROM.
Click to expand...
Click to collapse
i using this..
*Change the radio to 3.46.25.30 (Hot Fix For GPS Lock)
and also try the latest release of my rom.. (maybe you have bad file bad download)
b16b said:
i using this..
*Change the radio to 3.46.25.30 (Hot Fix For GPS Lock)
and also try the latest release of my rom.. (maybe you have bad file bad download)
Click to expand...
Click to collapse
Sorry, I tried that one as well yesterday. And I've downloaded your ROM a few times too...
Are you still working on the 6.1 ROM? Maybe a new version will just magically start working for me...
EDIT: Tried a fresh 3.46.25.30 and a fresh download of your ROM. Still nothing
After i flash rom. When my HD phone hang, so take out the battery and put it back to restart it .. the whole phone will reset to default..... just same like brand new phone without setting. it happen many times, what happen on my HD ?
Have you tried using the red reset button next to the SD card slot?
Yes i do , i try many kind of restart , but when my HD hang ... i restart it. it will back to default setting
if it happens always with the same rom, i suggest you try to change rom and see if that happens again. if it happens with different roms, you should flash back your stock default rom and then proceed flashing another custom rom and see if it does it again. Many times reverting to stock rom from time to time has been proven to solve some weird behaviours.
I would suggest flashing stock rom first before following this guide to flash a cooked rom again
crashDebug said:
if it happens always with the same rom, i suggest you try to change rom and see if that happens again. if it happens with different roms, you should flash back your stock default rom and then proceed flashing another custom rom and see if it does it again. Many times reverting to stock rom from time to time has been proven to solve some weird behaviours.
Click to expand...
Click to collapse
Thank you for suggest, i will try to find the original rom to flash and try it, see can solve my nightmare or not
Fallen Spartan said:
I would suggest flashing stock rom first before following this guide to flash a cooked rom again
Click to expand...
Click to collapse
erm.. i have read it.. but a bit confuse on that
natureborn said:
erm.. i have read it.. but a bit confuse on that
Click to expand...
Click to collapse
Did you use either HSPL or USPL before flashing rom? You will need to use one of these or your HD will hang. If you are having difficulty with that guide, post your query in that thread
I have got mine reset to default too.
My rom is Xannytech 2.2
HD Hangs. After a reset, it returns to the setup progress.
The setup progress is the setup progress of installation.
After the installation, calibrate the screen, set time zone.
the rom returns to function!!!
I am lucky I have saved all my data in the SD card, and backup my contact list and sms in Myphone.
It is quite a good auto recovery system.
The only application I installed is chinese font and htc 6.1 chinese input method.
Before the HD phone hangs, it is running opera 9.7.
I have ~ 500 contacts. and 300 sms..
As per Fallen Spartan's question above, have you used either USPL or HSPL before you flashed?
hktotti said:
I have got mine reset to default too.
My rom is Xannytech 2.2
HD Hangs. After a reset, it returns to the setup progress.
The setup progress is the setup progress of installation.
After the installation, calibrate the screen, set time zone.
the rom returns to function!!!
I am lucky I have saved all my data in the SD card, and backup my contact list and sms in Myphone.
It is quite a good auto recovery system.
The only application I installed is chinese font and htc 6.1 chinese input method.
Before the HD phone hangs, it is running opera 9.7.
I have ~ 500 contacts. and 300 sms..
Click to expand...
Click to collapse
Whats your SPL in bootloader? Was USPL or HSPL successful? Did you hard reset after flashing rom?
I had exactly the same problem after using xannys 2.2 rom. I'm using Hardspl. Even reflashed HSPL but it didnt help.
What did help was to flash another rom (Xnors) multiple times. Since that my phone did not hang again.
Z3rO` said:
I had exactly the same problem after using xannys 2.2 rom. I'm using Hardspl. Even reflashed HSPL but it didnt help.
What did help was to flash another rom (Xnors) multiple times. Since that my phone did not hang again.
Click to expand...
Click to collapse
Alternatively flash stock rom before flashing another cooked rom. This method appears to solve a number of reportewd issues
Z3rO` said:
I had exactly the same problem after using xannys 2.2 rom. I'm using Hardspl. Even reflashed HSPL but it didnt help.
What did help was to flash another rom (Xnors) multiple times. Since that my phone did not hang again.
Click to expand...
Click to collapse
I am sure Xannys 2.2 have this problem , i have already flash many many rom for more than one year is no problem.
The same happens to me but with all the roms (Xanny, Sh3lby 1.10/1.9/1.7 (although they were working fine), Xnor and PDAViet).
Do you know where I can find a stock rom?
- Bya -
EDIT: Found on the HTC official website and look here for the method.
EDIT2: Owned by Clyde ^^"
Bya said:
The same happens to me but with all the roms (Xanny, Sh3lby 1.10/1.9/1.7 (although they were working fine), Xnor and PDAViet).
Do you know where I can find a stock rom?
- Bya -
Click to expand...
Click to collapse
You can look here
Actually problems appear when I use Myphone. 2 options:
- Either it finished and then it freezes randomly from then, hard-reset itself, never complete it, reboot and get stuck on the black screen with radio information.
- Either it doesn't finish and when I try to exit/stop the program, it freezes and same than above happens.
Trying to get back to stock rom but battery's still not at 50% charge. So waiting a bit and playing with it without using myphone to see if it get blocked again...
- Bya -
Fallen Spartan said:
Did you use either HSPL or USPL before flashing rom? You will need to use one of these or your HD will hang. If you are having difficulty with that guide, post your query in that thread
Click to expand...
Click to collapse
Yes, i use HSPL (ISO-8859-1''HSPLWrapper_Blackstone_156OliNex ) , then the rom i flash is RUU_Dutty's_HD_WM6.5_5_Leo_R7 .
Well , i try to combine some of the opinion and flash rom again, this is what i do :
Step 1. I flash back the original rom ( RUU_BlackStone_hTC_Asia_WWE_1.18.707.3_Radio_52.49a.25.26_1.09.25.14_Ship ) . then hard reset twice.
Step 2. Then install HSPL (ISO-8859-1''HSPLWrapper_Blackstone_156OliNex ), then reset twice .
Step 3. Flash custom rom ( RUU_Dutty's_HD_WM6.5_5_Leo_R7 ), the reset twice .
Today is my second day after flash... so not sure will have the same old problem happen .... i wish nothing happen and can use smooth
I experienced the same issue with Miri V 14.0 two days ago. I never believe it does happen until it happened to me despite the fact that I always flash a custom rom before flashing any cooked rom.
Mine first came up with a message that I need to reset my device to factory settings because I have installed an application that is not compatible or not signed on my phone, message was when I performed a soft rest after phone freeze.
Hi guys!
I have been trying everything that I could find on XDA to fix my problem.
I got this HTC clone a few weeks ago, and it was working fine.
I decided to install a UI on it and it worked fine. After a while I got bored of the UI, so I decided to uninstall it. After the uninstall, the device indicated that it needed to be restarted. I did that, but after it rebooted, it started to reinstall Windows Mobile 6.1. I was annoyed by this, but was like, whatever, and let it continue.
Where the real problem started was when the device froze up (I left it alone for over an hour, but there was no change).
I then had to pull the battery. After I put the battery back into the T5355 it just keeps getting stuck on the "TOUCH Diamond2" screen.
I tried all the hard reset and soft reset tricks I could find and have no been able to either setting it back to factory or bootloader mode.
I was able to find a post that described how to place the boo.ini, flash.bin, and loader.bin file onto my micro sd card. I was able to to get the boot.ini an flash.bin files, but can't seem to find a loader.bin file (it that the actual OS rom?). I then found a post that showed how to use HiSilicon IDT to force the install of the OS Bin file (C02_HTC_20091102_R2127_英全视角B包.bin).
I followed the instructions on placing the T5355 into "Download" mode and pushing the OS bin fine to it.
I am able get the IDT software to detect the T5355 and start pushing the install, but the damned thing ends up giving an XLDR error.
PLEASE! PLEASE! Somebody help me! This phone is brand new and really want to get it working again.
Model: HTC(?) T5355
Please help me someone!!
Is there anyone out there that can help me???
I am so frustrated and can think of what else to do!
The biggest problem I have is that I can't use ActiveSync. If I could use that I wouldn't have much trouble.
Does anyone know how to use HiSilicon's IDT properly? The instructions I was working off of are in Russian. I think that a need a loader.bin file for the T5355 that I can put on my micro sd card...or maybe not...I don't know.
I just really want to get this device back to factory settings.
Please someone take pity on me!!!
enter bootloader [those orizontal strange colors]
try flashing a new rom. you may search and download the original 6.5 build from HTC
to enter bootloader, press "volume down + shutdown button" and then flash the rom
ATENTION: plug the USB cable, wait a few seconds, you should see USB on the lowest white color, then do the flashing job
I don't think you would be experiencing these problems with an original topaz
Please take care this is a HTC CLONE
Pisca said:
Please take care this is a HTC CLONE
Click to expand...
Click to collapse
oups, I'm high resolution on monitor, I thought it was saying "done" not "clone" ) ... there's a thread dedicated to china clones, look here http://forum.xda-developers.com/showthread.php?t=619643
run with a rom in bootloader, it shud work
enter bootloader [those orizontal strange colors]
try flashing a new rom. you may search and download the original 6.5 build from HTC
to enter bootloader, press "volume down + shutdown button" and then flash the rom
ATENTION: plug the USB cable, wait a few seconds, you should see USB on the lowest white color, then do the flashing job
Click to expand...
Click to collapse
DalvuS, thanks for the reply, but the issue is that I can't seem to get into bootloader mode . I wish I could. The T5355 seems to be stuck in the middle of wm 6.1 install. I need to somehow wipe the install and be able to push a reinstall back to the device.
I don't think you would be experiencing these problems with an original topaz
Click to expand...
Click to collapse
Exca that comment doesn't help me. It just makes me more sad. I was gipped when I bought the phone . I thought I paid for a "real" Diamond 2.
If you can't to catch the bootmode, looks like hardware problem.
You can't to repair it at home, imho. Try the specialized service.
..............
... and: are you sure about key combination for bootloader screen for CLONE?
Hello people, how can i dump my rom from my phone (mfu w71) for backup, because i cannot find any rom in english only in chinese. I started to dump the chinese rom with some chinese kitchen (K3系列ROM工具), but i'm stuck. I do not know to do anymore i have extracted ROM, SYS folder. I think it would be good to start another section on this forum for the chinese phones.
Some help from experienced cookers would me be much apreciated.
My T5355 is up and working!!!
Thanks to everyone who replied to my post!!!
I discovered that the problem was that the PC I was attempting the install from was running an AMD based processor.
I tried on the family laptop (which runs an Intel processor) and the install worked!
I AM SOOOO HAPPY!!!
b0gdi good luck with your issue. Try doing a search here in XDA for "dump my phone".
nothing[switched off] -> press start -> command -> bootloader -> bootloader commands -> system start -> play
checking one by one by interfering would have done the trick
I'm glad to hear that... so now you're ok
NEXT !
help me please
i Have Flash my phone 100 times with IDT for WM6.5 and WM6.1 all the versions my phone is T5355 Hot D2 but in one day i flash a rom that kill my phone the phone are conntinue to work but no screen picture only light i have try some russian Rom that kill my phone
the phone was been on guerant so i send him back to my supplier thay fix the phone but the factory said that thay need to change the screen so now thay really change the screen and the phone back to me with WM6.1 some New version 20.1.2010 some think like this i have made a call but the phone hang up and not make calls so i try to put him Back the WM6.5 English ROM that i use with this phone before i try to Flash Russian ROM that brake me the picture of the phone and block me the Bootloader Combination of SEnd+End+Power so that way i send him to repair .
so i try the English Rom that i have use before he DOwnload the Flash Fine but now the screen are stop to show picture But the Bootloader are work fine
so i try all the Roms that i have and all the same the screen dont want to show picture
some body have a same problem or can help me with this ?