Power button ONLY does restarts - Galaxy S I9000 Q&A, Help & Troubleshooting

I'm wondering if you guys have any fix for my problem
Here it goes :
One click on power button, it does a screen lock.
The problem is that when i hold my power button, it off the phone by itself.
I'm wondering if I want to bring back the menu when you hold the power button down? ( Besides flashing a new rom of course )
ie. Turn Power Off
Enable Flight Mode
Off Data Connection
Silent Mode
on Darkys v4.1 2.2 Froyo

Mine just started to behave like this aswell. Not out of the blue though, something went wrong with a flash and the phone got corrupted. I fixed it by installing a rom again with cwm and restored backups. Phone works fine now (as far as ive tested) except the powerbutton behaves like you describe, it makes the phone vibrate a few times and then reboots, without showing the menu to opt for shutdown and other options. Very frustrating.
Considering the way it happened im pretty sure some sort of corruption is the cause. I think a full flash with odin or heimdall may be needed. Will report back if I find out how to fix it.
Edit: I cwm-flashed extended power menu to restore my powermenu (well, replace it with custom). Still not sure what caused it, I think careless flashing, possibly involving an incompatible package.

Related

Lost Button & Keyboard Functionality

Started experiencing a strange issue with my tilt today..
When I soft reset it loads the Today screen, and then attempts to search for the contact 'wszx' (these keys are located next to each other). After this I can navigate the phone just fine using the touch screen, but the only buttons that work are the directional and center buttons located on the front of the phone, and the arrow keys on the keyboard. I cannot type at all using the keyboard, and pressing any of the other buttons does nothing (except the directional/center/Power). I also cannot Hard reset because the two soft-keys do absolutely nothing. I've hard reset in the past but it no longer works.
So am I SOL? I think I've tried everything.. and now I have a custom rom, etc on the phone and I have no way of getting it back to factory rom without the ability to hard reset.
Thanks for any help.
dam1en said:
Started experiencing a strange issue with my tilt today..
When I soft reset it loads the Today screen, and then attempts to search for the contact 'wszx' (these keys are located next to each other). After this I can navigate the phone just fine using the touch screen, but the only buttons that work are the directional and center buttons located on the front of the phone, and the arrow keys on the keyboard. I cannot type at all using the keyboard, and pressing any of the other buttons does nothing (except the directional/center/Power). I also cannot Hard reset because the two soft-keys do absolutely nothing. I've hard reset in the past but it no longer works.
So am I SOL? I think I've tried everything.. and now I have a custom rom, etc on the phone and I have no way of getting it back to factory rom without the ability to hard reset.
Thanks for any help.
Click to expand...
Click to collapse
Sounds like a hardware issue or simply a bad flash. Have you attempted to reflash the rom? Which rom are you using?
Well...
It wasn't working again this morning, but suddenly - out of nowhere - began to work properly. I'm stumped. If I ever figure out the exact issue I'll be sure to post back.
Thanks
Greetings,
I have same problem on my tytn...
Sometimes it suddenly starts working fine, but shortly it breaks again.
I have tried hard-reseting while it was working, but didnt help.
I think the problem appeared after charging my phone with a motorola v3 charger, so maybe it damaged my phone with over-voltage or something...
Anyway, if someone can suggest something i would be very grateful!
Hi I have exactly the same symptoms with my HTC Tytn II...when you power it on it starts typing letters (in my case CEDF). If the recording button is active it will start recording too. This happened suddenly and I haven't used any other charging apart from the usb and wall socket charger supplied with it.
All buttons (except front center key) and keyboard do not work. Any suggestions would be appreciated very much. This phone is only 8 months old.
Hi,
my Kaiser with dutty's WM6.1WWE ROM did the same this morning Yes I disabled the button 6 and stopped the voice recordings but all the hardware keys but few in the center of the keyboard are not responding. So I cant make or receive calls without taking the stylus out and touching the screen soft buttons andd that's pin in the ... while I am driving. I am using this ROM for almost a year now and I am extremely hapy (up to now) with its performance. When it all happened there were no activities on the phone - I woke up from a SMS notification (Yes I did receive an SMS from my bank) followed by repeting Voice Recordings. Any help will be highly appresiated! Thanks in advance!
keyboard problem
I am experiencing a similar problem with my stock tilt my keyboard does work however none of the text appears on the screen. I have tried hard reset and everything else I could think of, short of a clear storage reload. I would appreciate any help or suggestions from some of you more experienced users.
Bisonwill
anyone ever figure this problem out? im having the same thing happen now.
Same here
I've had it for a couple of weeks now.
I'm running WM6.1 from HTC (rom ver.3.29.422.1 from 2009-01-12) so nothing fancy here.
I even ordered and replaced the D-Pad and I replaced the keyboard (just the sticky part though). I totaly dismantled the phone and didn't find any issues with the cables.
Any ideas would be highly appreciated
Join the club!
This is crazy. My problem is exactly the same. I re-romed to the latest phoenix and it did not change a thing.
Help!
help....
any body here found a solution for the keypad/keyboard yet??? i have the same problem as you guys... any idea, thanks so much...
i have the same problem And there is something else. My Kaiser wakes up every 2 minutes - it's killing the battery. It works only for 6 hours now
Help
bump!!!
No more people with this issue or any solutions?
Pls! Help
ive joined the gang!
I decided to flash my cooked rom ive been working on.
i hadnt changed much in the kitchen and i think the flash has went badly.
it starts booting windows and where it should state "calibrate screen" it goes white and hangs there, buttons seem to respond by lighting up when pressed.
Now when i try to get it into bootloader or even hard reset it just doesnt work.
it just restarts the phone.
before this happened the backspace key hasnt been working for ages.
anybody got any ideas??
(lucky for me i have a backup kaiser!)
I'm having the same problem. Automatic wakeup, applications starting automatically, can't use keyboard, have to to use screen to use phone etc. I've hardreset using the clear storage method, reflashed a couple of times, but nothing helped. So here I am joining the club
If it's not a hardware issue, then try to flash another radio, many of the custom ROMs here doesn't include a radio, so if it's caused by a wrong radio, flash a new ROM without a radio doesn't help.
Check the Sticky for 'how to' if not aware.
PS: Check here for something need to know..
The question is.... how do I flash the device if I cant get it to go to boot loader and the OS wont boot properly !?
I think its an official Brick!
the really odd thing I've discovered is sometimes the OS leaves the loading screen on, and when it does if I press the FN and folder key, I get explorer up but its not responding... I haven't tried inserting a memory card yet to see if I can access that.
Danhargreaves said:
The question is.... how do I flash the device if I cant get it to go to boot loader and the OS wont boot properly !?
I think its an official Brick!
the really odd thing I've discovered is sometimes the OS leaves the loading screen on, and when it does if I press the FN and folder key, I get explorer up but its not responding... I haven't tried inserting a memory card yet to see if I can access that.
Click to expand...
Click to collapse
Try this:
1. Take out the battery from the phone.
2. Take out SIM card and SD card.
3. Press in and hold the CAMERA button.
4. Plugin to your computer using the USB cable, while keep holding press in the CAMERA button.
See does it enter the BOOTLOADER mode.
Once entered the BOOTLOADER mode, you can flash a new radio or rom right from there, in your regular way of running KaiserCustomRUU.exe.(Since you already have a HardSPL flashed on, otherwise a HardSPL is needed to flash first.)
Good luck.
Edit: If the power button and the camera button is still working, you can use the regular way of entering BOOTLOADER mode, and flash from bootloader mode or flash from SD card.
Originally posted by Manpreet @ www.sakajati.com
To enter in bootloader mode:
Simply Switch off your phone. Press and hold camera button and also press and hold the power button..You can remove ur finger from power button when phone is switched on but keep holding camera button until u come to bootloader …Now attach the usb to ur computer and do the flashing you normally do.
Click to expand...
Click to collapse
Thx for your suggestion:
I tried removing battery as sim and sd were already removed due to previous attempts in fixing!
so:
i removed battery (did not put back in), plugged in while holding camera
got nothing, so held power button at same time, the green light came on, then went off, and came back on again. but no bootloader.
i tried same procedure with battery in, and all i get is the OS loading up, no bootloader no matter how long i hold the buttons.
is there any other alternative method to get into bootloader (possibly involving other button presses)?
or any other ideas.
Really want to fix this as it was my "experimental" phone for cooking roms with.
Thanks again.
Suspect you have some hardware issue with the camera button. Can you ever take a photo with it?
Edit: Did you read through every post onthis thread:
MTTY (How to fix a bad ROM flash!)
If you tried that and still no luck, you can post your questions there. There are masters will keep an eye on that thread. And generally they only have time to look into their 'subscribed' threads, chances are they will not look into here.
Edit: Maybe the procedure I told is wrong, since I call from memory, check this:
dwny said:
If you have a bad flash....that's no reason to worry.
I haven't had to use MTTY to recover.
In most cases, if there's no issues with the Rom itself...you can pop out the battery and re-flash the same ROM from BootLoader Mode. This will also work if for some reason your computer crashes or loses power & restart during the FLASH.
If the Rom has issues.....the flash will not complete and the device will be stuck in BootLoader Mode. At this point,you must FLASH a FACTORY ROM!!
Pop the battery off 1st, power up the device, device will power up in BootLoader Mode, connect to pc & FLASH your devices FACTORY ROM. This will restore your device back to it's original out the box settings.
The above only works if the device has been put through the Hard SPL or SuperCID process.
I personally have never tried to flash a cooked ROM without unlocking any of my devices. From what I've read what others have experienced...the flash would just fail and they're stuck in BootLoader Mode.
Myself ... I've experienced bad flashes, bad cooked roms that I've cooked, lost power to a pc & had my pc crash during a flash. Listed above is how I've recovered. There is life after Bootloader Mode.
The only time you have to worry is if your device does not power up at all
As a public chef...it's your responsibility to set the parameters of your ROM! Meaning, Radio, HardSPL, program conflicts, etc.
You are not ultimately responsible if someone bricks their phone but if they pushed the issue, you could be hit with some form of liabilty because you failed on providing a simple Disclaimer that sets the expectation.
I hope I've been helpful.....
Click to expand...
Click to collapse
Edit again:
And try like:
Plug in USB first, and thenn press & hold Camera, Power button etc.
I remember once I read there is a way to enter bootloader without battery, just can not find the original again.

[Q] Nexus One CM7 power button problem

I have an AT&T unlocked Nexus One that I recently flashed to CM-7.0.3-N1 . I have had a problem unlocking the device with the power button both when I was running stock Gingerbread and now that I have installed CM7.
When the screen is off and my N1 is in standby, I push the power button and the screen turns on and then back off almost immediately. Sometimes there is a half second delay before the screen turns on and then off. This usually goes on 2 or 3 times until the screen will stay on and I can unlock my phone.
Has anyone seen or heard of this problem, and maybe knows of a fix? It could be hardware related, but the button definitely sends a signal to the phone and it works fine to shutdown or turn on the device from completely off. Thanks.
ummm the power button on the nexus one has an incredibly high failure rate, all over the forum here. its a design defect from the factory. that's why it has always been recommended to root the device immediately, and use trackball wake, so you avoid using the power button as much as possible. you have to send the device to HTC for repair, that's your only option...
Thanks for the information. I will have to look into repairs.
You are already running a rooted rom with track all wake. Use it. To reboot the the phone use quickboot. At this stage you really don't need the power button on your phone.
pcflet01 said:
... now that I have installed CM7.
I push the power button and the screen turns on and then back off almost immediate
Click to expand...
Click to collapse
This is a problem with CM7. Most advise turning off the screen off animation if it becomes a big problem for you. Make sure you are using the newest nightly and hope for a fix. I don't know if the RC's have this problem, but I would bet it appears on the 7.0.3 release.
At first glance that seems to have helped. Thanks for the advice!
No problem.
Also you can use widget locker to lock the screen then the trackball to wake, with that and quickboot I don't even touch my power button anymore. Although your problem doesn't sound like a broken power button so in your position I would switch ROMs and see what happens.
pcflet01 said:
I have an AT&T unlocked Nexus One that I recently flashed to CM-7.0.3-N1 . I have had a problem unlocking the device with the power button both when I was running stock Gingerbread and now that I have installed CM7.
When the screen is off and my N1 is in standby, I push the power button and the screen turns on and then back off almost immediately. Sometimes there is a half second delay before the screen turns on and then off. This usually goes on 2 or 3 times until the screen will stay on and I can unlock my phone.
Has anyone seen or heard of this problem, and maybe knows of a fix? It could be hardware related, but the button definitely sends a signal to the phone and it works fine to shutdown or turn on the device from completely off. Thanks.
Click to expand...
Click to collapse
I'm experiencing exactly this too on the latest RC. It doesn't seem to be complete button failure but it's acting like I've pressed it twice sometimes. Disabling the screen-on animation does seem to prevent it from popping back on. But it still sometimes goes on-then-off when I wake it with the power button. So now I'm using trackball wake too.
As others have mentioned, this does not sound like a powerbutton issue, because the powerbutton still turns on the screen. The problem is that the screen turns off immediately after it turns on.
When you flashed 7.0.3, did you come from a previous CM verison? From stock? My first suggestion would probably be to wipe the /system partition (in CWM, it is under mounts and storage -- with Amon_RA, you need to find a flashable zip to do it) and reinstall CM and gapps. This will not cause any data loss. Sometimes, if you install a new ROM over an old one, the upgrade script in CM can get confused and carry over files that aren't supposed to be carried over. The system wipe fixes that.
I've been using this RC since it came out in late June. Only this week did it start flipping out on me.
Sent from my Nook Color!
It still can't hurt anything to do a system wipe, just in case something got screwed up (these things can be so temperamental at times). And, like I said, you won't lose any of your data.
bassmadrigal said:
It still can't hurt anything to do a system wipe, just in case something got screwed up (these things can be so temperamental at times). And, like I said, you won't lose any of your data.
Click to expand...
Click to collapse
I'm currently using S2E for apps2ext and some data2ext. How would a system wipe and reinstall interact with that? I'm a bit nervous on that front.
A system wipe shouldn't change any of that. It is one benefit of using S2E as it is a standard app that is stored in the /data partition without any changes to the /system partition.
Anyway, to be safe, it is a good idea to do a nandroid backup anytime you are doing something that involves the majority of the features in recovery.
It's a hardware problem for me. Failed completely as of today.
Sent from my Nexus One using Tapatalk
CM7 7.1.0
My power button seems to be in the process of completely failing. The new CM7 update to 7.1.0 has made it possible for me to lock the screen without using the power button using the "Notification power widget" -> "Go to sleep". Now the only times I have to use the power button are to shut the phone down or wake it up, which seems to be easier when the phone is plugged in to a wall charger. Are there any simple apps for shutting the phone down and maybe waking it up at a set time?
The only reliable trick I found to turn it back on was to plug into the wall and take the battery out/in a few times till it vibrated.
I ended up getting a replacement phone and then I sent the Nexus to HTC. They quoted a $55 repair cost off warranty which my credit card insurance would've covered, but when I asked for an invoice they offered to just waive the charges. Finally over a month later it came back fixed.
The app Easy Reboot can shut the phone down.
Sent from my Nook Color!
I also use an app called Lock Screen, which just locks the screen. I have it stored in my dock, because I don't like the space being used in the notification widget.
CM7 has an option for one of the items in the notification tray widget to be a lock screen button.
cmstlist said:
I'm experiencing exactly this too on the latest RC. It doesn't seem to be complete button failure but it's acting like I've pressed it twice sometimes. Disabling the screen-on animation does seem to prevent it from popping back on. But it still sometimes goes on-then-off when I wake it with the power button. So now I'm using trackball wake too.
Click to expand...
Click to collapse
THANK YOU!!!! This has been driving me crazy. Turning off the screen-off animations did nothing, but turning off the screen-on animation seems to have fixed the issue. My power button is toast (my new power button ribbon cable just arrived... time for surgery), and I've been using the trackball to wake my phone. Before the power button died, it did the same thing. I'm using CM7.2. I installed it after rooting and went straight to cm7.2 from stock, so obviously the cyanogemnod crew haven't fixed the issue since 7.0.3 when this thread started.

[Solved] Hardware issue with power button

Build date 1007 - in service August 2010.
I've been running Pinnacle 1.2 (been on it since v1.0).
Just moments ago I've found the power button to be unresponsive. This happened after I rebooted into recovery, sticking me there for a while.
I was stuck in a recovery loop- pull batt, reinstall batt, automatic boot back into recovery.
Somewhere in the process of trying different combinations of battery pulls with cable installs and volume up/down holds (trying for download mode) I ended up finally launching the ROM, but w/o a power button all I can do is pull the battery, and the moment I do, the phone automatically wakes w/o even touching the power button (which is totally new to me).
Any input would certainly be appreciated.
My first order of business is to flash to stock (JF6, bootloaders and all if all else failed) but being that it automatically boots when the battery is installed I don't think even a jig would help...or is the beer steering me wrong?
I am confused. You can go back to stock or no?
I cannot get into download mode. The only way to power the phone off is via battery pull.
I cant flash anything from recovery because it says the power button is disabled (it is).
As I put the battery back in the phone boots immediately...I mean the at&t screen lights up my palm before I put the cover on or even flip the phone over.
Use an app from market to enter download mode? system toolbox free is one
Used Odin to go back to stock KF1 and still no power button. Now System Toolbox won't work w/o root/busybox. lol
Once my phone falls asleep I can't wake it back up.
It may seem obvious that the power button is physically broken but I don't know why the phone boots up as soon as the battery is installed...that was never the case before this issue came up.
watsa? Anyone?
Can anyone else shed some light on what would make the phone boot when the battery is inserted (happened at the same time the power button became unresponsive), essentially denying me the opportunity to get to download mode.
beyond this point I am consfused myself. I initially blamed Pinnacle and thought going back to stock might fix it which obviosly didn't happen.. It seems like your power button is always "pushed" so as soon as you pop your battery in phone reboots..
watsa said:
beyond this point I am consfused myself. I initially blamed Pinnacle and thought going back to stock might fix it which obviosly didn't happen.. It seems like your power button is always "pushed" so as soon as you pop your battery in phone reboots..
Click to expand...
Click to collapse
On a second thought if it was the case then power button should have messed up functioning of your phone even after powering on. So I am consfused more. Need a hardware expert here
I'm preparing myself to deal with my beloved phone finally letting me down after all the success we've had...it's just really bad timing as I'm currently unemployed, broke and only 13ish months into a 48 month contract.
Ok, so after a physical tear down it seems to be in the external plastic of the button itself?
After removing the outer case and reinserting the battery I noticed it did not automatically boot up. I pressed the actual power switch/button that is connected to the board and the phone then powered up. I let it finish booting and held the power button down and the power options menu popped up. I clicked Power Off and it shut down fine.
This means it certainly isn't Pinnacle ROM (never thought it was, personally), or software related at all. Now to figure out what is going on between the plastic external power button and the power switch on the board.
Edit: Nothing was there? I blew out the dust reassembled the phone and now it works fine. Weird.

Captivate Power button not working and boots with battery automatically!

I got a captivate, over a year old, never had a problem been through many flashes and custom roms etc....
Well it was actually running stock rom (froyo) for a while and suddenly the power button stopped working and the phone automatically booted when the battery was inserted. I read about the camera trick, took a picture and pressed the button a few times and it started working again. A few days later the button stopped responding and also it boots with the battery automatically again but this time the camera trick doesn't work (tried for a while many times), I did the factory update to gingerbread just to try that for the heck of it and still nothing. any ideas, suggestions, or other advice??
I think you have a problem with motherboard. Even the power button is jammed, it won't turn on the device as soon as you put the battery in.
I had same problem with PC and came out the motherboard had problem.
Same problem as well. Just started yesterday/today
Could it be software?
I'm running hacksung v16/17
I tried doing data/cache/system/dalvik reset and then reinstall, but it hasn't changed anything.
I might do an ODIN restore but I thought it was hardware.
Its hardware..check out mobiletechvideos.com they offer a power button replacement service.
sent mine put for the same issue, got it back in a week, works prefect now.
power button not working
... that's a hardware issue ... or so i read
you can take it apart and clean it you find instructions online
or you can use apps (which allow you to use the volume buttons to wake the screen)
i use MIUI .. it has a built in function (to use the volume buttons to wake the screen)
Time to get a new phone. I wouldn't waste money trying to repair it, something else will break and then what? Take a backup of your apps and data.
http://forum.xda-developers.com/showthread.php?t=1193057
Have you tried using odin 1 click to restore back to stock? That worked for me.
I just posted my solution here. See if it works for you, too.

Power button issue

I just discovered yesterday that my power button seem to be not working. Pressing it doesnt lock the screen and long pressing it doesnt bring up the power options. Tried wiping everything and still the issue remains. When I pull my battery and then insert it back the phone boots itself, as if the power button is pressed all the time (even though i can still click it and its not stuck). Ive been using rom toolbox for the power menu but choosing to turn off the phone makes my phone have a screen freeze, all other options work like reboot, fast reboot, reboot recovery etc. Anyone know how to fix this?
Edit: After a couple of days my power button is working again
Kcube989 said:
I just discovered yesterday that my power button seem to be not working. Pressing it doesnt lock the screen and long pressing it doesnt bring up the power options. Tried wiping everything and still the issue remains. When I pull my battery and then insert it back the phone boots itself, as if the power button is pressed all the time (even though i can still click it and its not stuck). Ive been using rom toolbox for the power menu but choosing to turn off the phone makes my phone have a screen freeze, all other options work like reboot, fast reboot, reboot recovery etc. Anyone know how to fix this?
Edit: After a couple of days my power button is working again
Click to expand...
Click to collapse
How did you get it to work? Or did it started working on it's on? Thanks
I've seen that happen on mine, due to a bad USB charge port. Replaced it, problem disappeared.
Any chance your device sometimes thinks it is docked to a docking station?
Inexpensive part to obtain, less than 10 dollars (usd), takes about 15 minutes or less to replace.
In the 2+ years I've had mine, I've gone through 4 of them LOL...I'm hard on charge ports I guess.
Kcube989 said:
I just discovered yesterday that my power button seem to be not working. Pressing it doesnt lock the screen and long pressing it doesnt bring up the power options. Tried wiping everything and still the issue remains. When I pull my battery and then insert it back the phone boots itself, as if the power button is pressed all the time (even though i can still click it and its not stuck). Ive been using rom toolbox for the power menu but choosing to turn off the phone makes my phone have a screen freeze, all other options work like reboot, fast reboot, reboot recovery etc. Anyone know how to fix this?
Edit: After a couple of days my power button is working again
Click to expand...
Click to collapse
It just started working again. When I turned off my phone to place my sim back and it didnt boot up automatically, I knew the power button is working again. Pressed the power button, device booted up and the issue is gone. I dont know if mh device thinks its docked, i dont have a docking station and ive never had problems with my charging port yet.
I've been using my N7000 for 2 years and this thing happened for 3-4 times. The lock button will be like stop working, sometimes it is like being press all the time and the problem will be sorted out by itself. Normally when this happens, the phone will be laggy and will reboot by itself. Is it a common thing for this phone?how do you get your phone fixed Kcube989?

Categories

Resources