Help
I got the Ruu until and the nbh file for both my ROM and also my SPL but when i run the RUU it goes through to update the phone even reboots the phone and brings up the progress bar on phone and screen. BUT it sticks at 0% and then says cannot communicate with phone.
Related
I am having a problem that I hope someone can help me with.
I have an SX-66 with WM5 on it. The other day the device suddenly stopped booting. I can get the device to turn on, soft-reset, hard reset and get into bootloader mode, but whenever I try to boot the operating system it gets stuck on the colored stripe boot screen and just sits there showing the version numbers and nothing else. I have followed the instructions on the Wiki for downgrading but I still have the same problem. I have tried draining the battery fully and recharging but still no dice. I am even able to reflash the device with my laptop and it says it succeeds with the up/downgrade but then it just gets stuck again. If I try to install a 1.40 the device says that the flash is successful but then WM5 tries to boot again and I am stuck at the striped screen.
Can someone please help me out? Do I have a brick?
Hi There,
I installed HardSPL without any issues, but now that i want to install Dutty's ROM v1.1 the following happens:
I extract the files in the .zip to a new folder. I run the DiamonCustomRUU application, and follow the steps. At first i get a black screen on my phone, then i get the tricolor screen. Here it displays the SPL version properly, after a couple of seconds it displays "USB" in the bottom bit, then it goes to a grey screen with an indicator bar. This bar won't go beyond 0%, and after a while i get the message in the update utility that communications have been interrupted, and i'm referred to the "Recovery program"...
Is this a familiar problem? Can anyone help me fix this?
I downloaded your Kaiserunlock utility and, followed your step and when my phone was ready to finished updating ( 95%) i got a message that it disconnected so I went thrh the recovery feature and now my 8925 is stuck in my tricolor screen and I keep trying the recovery PDA recovery ROM utility 3.14 program and nothing happens keeps doing the same over and over the whole process, advice please.
bump
/bump************
What you need to do ,is reflash back to your original rom, found here
http://wiki.xda-developers.com/index.php?pagename=Kaiser_ROMs
And then follow these steps to do it right.
http://forum.xda-developers.com/forumdisplay.php?f=378
Hi, I have an htc touch diamond that will not boot past the splash. It turns on, says htc diamond without red letters. I have tried soft reset & hard reset, doesnt work. also phone does not turn on by power button but only the reset button. Every time I try to flash or unlock it says "Error 262", I've tried soft reset and continuing the setup and the error comes up again. I've tried the whole thing of changing the driver from 2007 to 2003 and completed it and still has not fixed error 262. I've tried many different roms and the only ones that bypass 262 are the .exe file rom setups, but after installed still doesnt boot past splash screen. the farthest ive gotten with one .exe is going through the phone setup, but after the setup the phone turns off. the only way my computer notices the phone and the way i flash the phone is when it is in bootloader. have also tried the bootloader where you press the back button. I've been trying so hard to fix this phone but it just wont happen. please help?
ryan21x5 said:
Hi, I have an htc touch diamond that will not boot past the splash. It turns on, says htc diamond without red letters. I have tried soft reset & hard reset, doesnt work. also phone does not turn on by power button but only the reset button. Every time I try to flash or unlock it says "Error 262", I've tried soft reset and continuing the setup and the error comes up again. I've tried the whole thing of changing the driver from 2007 to 2003 and completed it and still has not fixed error 262. I've tried many different roms and the only ones that bypass 262 are the .exe file rom setups, but after installed still doesnt boot past splash screen. the farthest ive gotten with one .exe is going through the phone setup, but after the setup the phone turns off. the only way my computer notices the phone and the way i flash the phone is when it is in bootloader. have also tried the bootloader where you press the back button. I've been trying so hard to fix this phone but it just wont happen. please help?
Click to expand...
Click to collapse
If this happens, you can just soft-reset the device and run RUU again. The update process will then continue.
Note: At this stage, the Wince is destroyed; instead, it is in upgrade mode.
for official rom you can find at http://www.shipped-roms.com/index.php?category=windows mobile&model=Diamond
Greetings,
This phone will not let me RUU it, it constantly is rebooting even during the RUU process. Then it always ends in some error. It goes thru startup, installs some apk's (always), goes into android OS and after like two minutes, restarts by itself.
Bootloader stays on, though. Can't format it from there. Factory reset does nothing.
anyone???
ruu should work as long as you relock your bootloader. try this file out in this thread
http://forum.xda-developers.com/showthread.php?t=2013122