Hi There,
I installed HardSPL without any issues, but now that i want to install Dutty's ROM v1.1 the following happens:
I extract the files in the .zip to a new folder. I run the DiamonCustomRUU application, and follow the steps. At first i get a black screen on my phone, then i get the tricolor screen. Here it displays the SPL version properly, after a couple of seconds it displays "USB" in the bottom bit, then it goes to a grey screen with an indicator bar. This bar won't go beyond 0%, and after a while i get the message in the update utility that communications have been interrupted, and i'm referred to the "Recovery program"...
Is this a familiar problem? Can anyone help me fix this?
Related
At I was Trinity flash my notebook starts hibernation and now is impossible next flash.
After reset appears only first HTC screen.
Each next flash normal start, but only 2% progress and Trinity go off and in PC appears INVALID VENDER ID 294. I Try 6 different ROM.
If I try flash by SD card, appears NOT ALLOW.
By Active Sync is impossible connect.
CID I have Unlock. I was Flashing before several without problems.
Some Help?
I’m sorry for my English.
When you turn the device on what do you see: No GSM?
How far is it booting (splash screen/windows ce) ?
When you start in 3 color screen what version numbers can you see?
The problem you describe sounds more like you cancelled a ROM update in the middle. (e.g. when it was looking stuck but in fact it wasn't you cancelled the update or you romoved the cable or hibernation prozess stoped your PC)
After first bad flash Boot only to 3 colors screen.
Now (after next flash to 2%) go to Splash screen.
Off device is impossible. Still is on 3 colors screen or splash screen. I must battery take off.
Number in 3 color screen is:
TRIN100
IPL-0-50
TRIN100
SPL-1-07-0000
After the bad flash, you no longer got superCID, so you need to find the right rom for your device.
As long as you just get "invalid vendor id", keep trying different original rom's.
I was try original ROM and still same problem.
Only 2% progress...
I was try 11 type of Rom.
It had a Chinese ROM and I wanted it in English, after flashing the ROM I wanted, it restarted and would not get past the startup screen.
Phone: Dopod s900 with WM6.1
Soft reset: ends up at startup screen and then stops
Hard reset: same thing happens
Bootloader: coloured screen, can't do anything
I tried to flash again in the coloured screen (bootloader?) and when it showed my current image, it was blank. Does this mean I have nothing in my phone right now? None of the flash ROMs I'm trying to install right now are working.
I don't know what to do...is it broken?
salenasg said:
It had a Chinese ROM and I wanted it in English, after flashing the ROM I wanted, it restarted and would not get past the startup screen.
Phone: Dopod s900 with WM6.1
Soft reset: ends up at startup screen and then stops
Hard reset: same thing happens
Bootloader: coloured screen, can't do anything
I tried to flash again in the coloured screen (bootloader?) and when it showed my current image, it was blank. Does this mean I have nothing in my phone right now? None of the flash ROMs I'm trying to install right now are working.
I don't know what to do...is it broken?
Click to expand...
Click to collapse
In the colored screen does it say "serial" or "usb" near the bottom?
If it says serial try to plug in the usb and if it changes and then says "usb" you should be able to re-flash the rom.
Thanks,
It says usb because I have it plugged in but which rom am I supposed to use? Its very original one? The one in Chinese? because I can't even find it..and I want it to be in English. What made it freeze in the first place was because i tried to flash a cooked rom. Will my phone work again after I flash a new ROM?
Thank you! It worked <3
Basically, I follow all directions to flash my new rom (this is my third new flash ) and when the boot loader runs, it starts to run the flashing program, but the programs just flashes "No file found!" then stays at the rgb screen.
Ideas?
Regards
Smith
EDIT: Solved.
Help
I got the Ruu until and the nbh file for both my ROM and also my SPL but when i run the RUU it goes through to update the phone even reboots the phone and brings up the progress bar on phone and screen. BUT it sticks at 0% and then says cannot communicate with phone.
hi guys
i tried to install android on my xperia x1 but some thing went wrong
now when i start my mobile a black screen appear with a blue writing (i think this is fastboot)
I tried to boot a boot.img and now a second black screen with white writing appears (I think this is adb)
when i try to hspl my device (power and volume down) it says (spl 0.72.0000)
I cant go back for a wm rom nor install android rom
I tried many wm rom but nothing is working
i don't know what to do!!!!!!!!!!!!!!!!????
please help guys
I tried to install android following this http://forum.xda-developers.com/showthread.php?t=1329379
first I tried to do hspl 0.78 .... I did it and it was a success
but I couldn't complete everything and android won't run on my mobile
when i power it on a black screen with blue writing appears at first
then i tried to boot an img using fast boot and a new black screen with white writing appears but nothing else
then I give up and I want to get WM back
I tried to go back to the stack spl 0.72 and it was ok but my phone won't run WM it keeps show a black screen with withe writing and stop
when I try to enter boot loader and flash a new rom using sd card (formatting my SD with fat32 and put a rom named kovsimg.nbh on it) it stuck on loading and nothing else
and even when i try to flash a new room using KovskyAdvancedRUU it stop at 0% and won't continue
now i don't have any OS not WM and not Android
I even can't change to hspl like 0.78 or 0.52
thats all I did
I hope you can help me
finally
android worked
when the black screen with white writing appears I connected the phone to the pc and run (adb shell)
and it worked >>>>>>>
thank you very much
but I don't know if I can go back to WM saftly