At I was Trinity flash my notebook starts hibernation and now is impossible next flash.
After reset appears only first HTC screen.
Each next flash normal start, but only 2% progress and Trinity go off and in PC appears INVALID VENDER ID 294. I Try 6 different ROM.
If I try flash by SD card, appears NOT ALLOW.
By Active Sync is impossible connect.
CID I have Unlock. I was Flashing before several without problems.
Some Help?
I’m sorry for my English.
When you turn the device on what do you see: No GSM?
How far is it booting (splash screen/windows ce) ?
When you start in 3 color screen what version numbers can you see?
The problem you describe sounds more like you cancelled a ROM update in the middle. (e.g. when it was looking stuck but in fact it wasn't you cancelled the update or you romoved the cable or hibernation prozess stoped your PC)
After first bad flash Boot only to 3 colors screen.
Now (after next flash to 2%) go to Splash screen.
Off device is impossible. Still is on 3 colors screen or splash screen. I must battery take off.
Number in 3 color screen is:
TRIN100
IPL-0-50
TRIN100
SPL-1-07-0000
After the bad flash, you no longer got superCID, so you need to find the right rom for your device.
As long as you just get "invalid vendor id", keep trying different original rom's.
I was try original ROM and still same problem.
Only 2% progress...
I was try 11 type of Rom.
Hello all,
first let me apologize for the long post, and my noobiness. I'm new to the smartphone world, I've sucessfully flashed my Kaiser (from work). Also, I would like to thank everyone who is cooking!
I have the HTC Mteor, which I'm trying to Flash to WM6.1.
When I got it (used), I did a hard reset, and it went back to WM5 in Russian.
I believe I successfully unlocked it, and can now get to the tri-color screen.
It reads:
BBEE100
IPL-0.90
BREE100
SPL-2.05
Every ROM (including the original from HTC) opens, forces the phone to the tri-color screen, and then dies. Error 260, 262, etc.
I've searched the forums, and read that the SPL should be 1.10, but I can't get that to install either.
Any help/suggestions?
Thanks,
Jeff
jjmorris100 said:
Hello all,
first let me apologize for the long post, and my noobiness. I'm new to the smartphone world, I've sucessfully flashed my Kaiser (from work). Also, I would like to thank everyone who is cooking!
I have the HTC Mteor, which I'm trying to Flash to WM6.1.
When I got it (used), I did a hard reset, and it went back to WM5 in Russian.
I believe I successfully unlocked it, and can now get to the tri-color screen.
It reads:
BBEE100
IPL-0.90
BREE100
SPL-2.05
Every ROM (including the original from HTC) opens, forces the phone to the tri-color screen, and then dies. Error 260, 262, etc.
I've searched the forums, and read that the SPL should be 1.10, but I can't get that to install either.
Any help/suggestions?
Thanks,
Jeff
Click to expand...
Click to collapse
install this official rom from HTC
http://rapidshare.com/files/66085556/RUU_BREE100_1.34.261.1_1.38.00.10_HTCRUS_SHIP.exe
Its for RUS QTEK_AO7.
Then you will have SPL 1.10
I have similar problem
I had ROM 6.1 from Futureshock...still problem with radio (my phone couldn´t accessble but signal icon shows good signal, radio version 1.38.0000), so I decided flash some original ROM. Aftet that my booting stuck on HTC logo or Windows Mobile logo. So I can´t use normal way to flashing. Only from SD card or first turn on phone to boot loader mode and than attach usb cable and start flashing. From SD card (where is renamed ROM BREEIMG.NBH) after enter into bootloader mode start loading and than just turn to trhreecolour menu where is BREE100 - IPL-0.90 and BREE100-1.10.0000 and doesn´t want continue. If I flash ROM via USB cable (first go to threecolour mode, than attach cable) than run ROMUpdateUtility.exe and flash process is being started but always die on 2%, than autoreboot and again stuck on HTC logo.
I tried soft reset, I tried lot of ROM versions HTCRUS, HTCEUR, QTEKEUR, FUTURESHOCK but still same problem during flash ROM stop on 2%...
Any ideas how to back life to my MTeoR?
Can I use application like MTTY? Could me help this program?
Thanks for any help...
hi, can any1 send me a link for a ger version of wm6.0pro ?
Wigo said:
I had ROM 6.1 from Futureshock...still problem with radio (my phone couldn´t accessble but signal icon shows good signal, radio version 1.38.0000), so I decided flash some original ROM. Aftet that my booting stuck on HTC logo or Windows Mobile logo. So I can´t use normal way to flashing. Only from SD card or first turn on phone to boot loader mode and than attach usb cable and start flashing. From SD card (where is renamed ROM BREEIMG.NBH) after enter into bootloader mode start loading and than just turn to trhreecolour menu where is BREE100 - IPL-0.90 and BREE100-1.10.0000 and doesn´t want continue. If I flash ROM via USB cable (first go to threecolour mode, than attach cable) than run ROMUpdateUtility.exe and flash process is being started but always die on 2%, than autoreboot and again stuck on HTC logo.
I tried soft reset, I tried lot of ROM versions HTCRUS, HTCEUR, QTEKEUR, FUTURESHOCK but still same problem during flash ROM stop on 2%...
Any ideas how to back life to my MTeoR?
Can I use application like MTTY? Could me help this program?
Thanks for any help...
Click to expand...
Click to collapse
I'm not sure that I understand well, but if you flash from SD, it finish in 100% and than go to three color boot screen? ....
Hi alebo caf Vašek ;-)
My problem is that always stuck on boot image HTC or Windows Mobile blue screen. I can´t use way copy necesseary files to root of phone memmory and than run sspl etc...I have to turn manualy to three-color mode, than connect USB cable and run upgrade utility but still froze instalation on 2%, If I use SD card methode with BREEIMG file uploading doesn´t start....
p.s.: Ak by si mal dáku radu tak možno lepšie vysvetliť po česky ;-). Moje ICQ 208-393-971
Dík
CZ Rom
I would like to install new ROM into my Mteor, but I have no experience doing it. I do not know which version to try, all I need is to be able to enter czech letters on HW keyboard as with original ROM. Any sugestion? I preffer personal answer in czech language ([email protected])
Hi There,
I installed HardSPL without any issues, but now that i want to install Dutty's ROM v1.1 the following happens:
I extract the files in the .zip to a new folder. I run the DiamonCustomRUU application, and follow the steps. At first i get a black screen on my phone, then i get the tricolor screen. Here it displays the SPL version properly, after a couple of seconds it displays "USB" in the bottom bit, then it goes to a grey screen with an indicator bar. This bar won't go beyond 0%, and after a while i get the message in the update utility that communications have been interrupted, and i'm referred to the "Recovery program"...
Is this a familiar problem? Can anyone help me fix this?
I downloaded your Kaiserunlock utility and, followed your step and when my phone was ready to finished updating ( 95%) i got a message that it disconnected so I went thrh the recovery feature and now my 8925 is stuck in my tricolor screen and I keep trying the recovery PDA recovery ROM utility 3.14 program and nothing happens keeps doing the same over and over the whole process, advice please.
bump
/bump************
What you need to do ,is reflash back to your original rom, found here
http://wiki.xda-developers.com/index.php?pagename=Kaiser_ROMs
And then follow these steps to do it right.
http://forum.xda-developers.com/forumdisplay.php?f=378
Hi there!
I have some trouble with my Kaiser. Each time I try to boot him, it stucks at Bootloader and shows me No image file. I already tried to flash another ROM, to reinstall a SPL, nothing helps. What can I do? Please explain me what to do, if there is a possibility to fix it.
http://forum.xda-developers.com/showthread.php?t=423486
The sticky is a good source of information.