After flashing new rom, phone no longer works. - Touch Diamond CDMA

It had a Chinese ROM and I wanted it in English, after flashing the ROM I wanted, it restarted and would not get past the startup screen.
Phone: Dopod s900 with WM6.1
Soft reset: ends up at startup screen and then stops
Hard reset: same thing happens
Bootloader: coloured screen, can't do anything
I tried to flash again in the coloured screen (bootloader?) and when it showed my current image, it was blank. Does this mean I have nothing in my phone right now? None of the flash ROMs I'm trying to install right now are working.
I don't know what to do...is it broken?

salenasg said:
It had a Chinese ROM and I wanted it in English, after flashing the ROM I wanted, it restarted and would not get past the startup screen.
Phone: Dopod s900 with WM6.1
Soft reset: ends up at startup screen and then stops
Hard reset: same thing happens
Bootloader: coloured screen, can't do anything
I tried to flash again in the coloured screen (bootloader?) and when it showed my current image, it was blank. Does this mean I have nothing in my phone right now? None of the flash ROMs I'm trying to install right now are working.
I don't know what to do...is it broken?
Click to expand...
Click to collapse
In the colored screen does it say "serial" or "usb" near the bottom?
If it says serial try to plug in the usb and if it changes and then says "usb" you should be able to re-flash the rom.

Thanks,
It says usb because I have it plugged in but which rom am I supposed to use? Its very original one? The one in Chinese? because I can't even find it..and I want it to be in English. What made it freeze in the first place was because i tried to flash a cooked rom. Will my phone work again after I flash a new ROM?

Thank you! It worked <3

Related

Dead Trinity after bad flash-Invalid Vender ID 294

At I was Trinity flash my notebook starts hibernation and now is impossible next flash.
After reset appears only first HTC screen.
Each next flash normal start, but only 2% progress and Trinity go off and in PC appears INVALID VENDER ID 294. I Try 6 different ROM.
If I try flash by SD card, appears NOT ALLOW.
By Active Sync is impossible connect.
CID I have Unlock. I was Flashing before several without problems.
Some Help?
I’m sorry for my English.
When you turn the device on what do you see: No GSM?
How far is it booting (splash screen/windows ce) ?
When you start in 3 color screen what version numbers can you see?
The problem you describe sounds more like you cancelled a ROM update in the middle. (e.g. when it was looking stuck but in fact it wasn't you cancelled the update or you romoved the cable or hibernation prozess stoped your PC)
After first bad flash Boot only to 3 colors screen.
Now (after next flash to 2%) go to Splash screen.
Off device is impossible. Still is on 3 colors screen or splash screen. I must battery take off.
Number in 3 color screen is:
TRIN100
IPL-0-50
TRIN100
SPL-1-07-0000
After the bad flash, you no longer got superCID, so you need to find the right rom for your device.
As long as you just get "invalid vendor id", keep trying different original rom's.
I was try original ROM and still same problem.
Only 2% progress...
I was try 11 type of Rom.

Flashing ROM and SPL

Hello all,
first let me apologize for the long post, and my noobiness. I'm new to the smartphone world, I've sucessfully flashed my Kaiser (from work). Also, I would like to thank everyone who is cooking!
I have the HTC Mteor, which I'm trying to Flash to WM6.1.
When I got it (used), I did a hard reset, and it went back to WM5 in Russian.
I believe I successfully unlocked it, and can now get to the tri-color screen.
It reads:
BBEE100
IPL-0.90
BREE100
SPL-2.05
Every ROM (including the original from HTC) opens, forces the phone to the tri-color screen, and then dies. Error 260, 262, etc.
I've searched the forums, and read that the SPL should be 1.10, but I can't get that to install either.
Any help/suggestions?
Thanks,
Jeff
jjmorris100 said:
Hello all,
first let me apologize for the long post, and my noobiness. I'm new to the smartphone world, I've sucessfully flashed my Kaiser (from work). Also, I would like to thank everyone who is cooking!
I have the HTC Mteor, which I'm trying to Flash to WM6.1.
When I got it (used), I did a hard reset, and it went back to WM5 in Russian.
I believe I successfully unlocked it, and can now get to the tri-color screen.
It reads:
BBEE100
IPL-0.90
BREE100
SPL-2.05
Every ROM (including the original from HTC) opens, forces the phone to the tri-color screen, and then dies. Error 260, 262, etc.
I've searched the forums, and read that the SPL should be 1.10, but I can't get that to install either.
Any help/suggestions?
Thanks,
Jeff
Click to expand...
Click to collapse
install this official rom from HTC
http://rapidshare.com/files/66085556/RUU_BREE100_1.34.261.1_1.38.00.10_HTCRUS_SHIP.exe
Its for RUS QTEK_AO7.
Then you will have SPL 1.10
I have similar problem
I had ROM 6.1 from Futureshock...still problem with radio (my phone couldn´t accessble but signal icon shows good signal, radio version 1.38.0000), so I decided flash some original ROM. Aftet that my booting stuck on HTC logo or Windows Mobile logo. So I can´t use normal way to flashing. Only from SD card or first turn on phone to boot loader mode and than attach usb cable and start flashing. From SD card (where is renamed ROM BREEIMG.NBH) after enter into bootloader mode start loading and than just turn to trhreecolour menu where is BREE100 - IPL-0.90 and BREE100-1.10.0000 and doesn´t want continue. If I flash ROM via USB cable (first go to threecolour mode, than attach cable) than run ROMUpdateUtility.exe and flash process is being started but always die on 2%, than autoreboot and again stuck on HTC logo.
I tried soft reset, I tried lot of ROM versions HTCRUS, HTCEUR, QTEKEUR, FUTURESHOCK but still same problem during flash ROM stop on 2%...
Any ideas how to back life to my MTeoR?
Can I use application like MTTY? Could me help this program?
Thanks for any help...
hi, can any1 send me a link for a ger version of wm6.0pro ?
Wigo said:
I had ROM 6.1 from Futureshock...still problem with radio (my phone couldn´t accessble but signal icon shows good signal, radio version 1.38.0000), so I decided flash some original ROM. Aftet that my booting stuck on HTC logo or Windows Mobile logo. So I can´t use normal way to flashing. Only from SD card or first turn on phone to boot loader mode and than attach usb cable and start flashing. From SD card (where is renamed ROM BREEIMG.NBH) after enter into bootloader mode start loading and than just turn to trhreecolour menu where is BREE100 - IPL-0.90 and BREE100-1.10.0000 and doesn´t want continue. If I flash ROM via USB cable (first go to threecolour mode, than attach cable) than run ROMUpdateUtility.exe and flash process is being started but always die on 2%, than autoreboot and again stuck on HTC logo.
I tried soft reset, I tried lot of ROM versions HTCRUS, HTCEUR, QTEKEUR, FUTURESHOCK but still same problem during flash ROM stop on 2%...
Any ideas how to back life to my MTeoR?
Can I use application like MTTY? Could me help this program?
Thanks for any help...
Click to expand...
Click to collapse
I'm not sure that I understand well, but if you flash from SD, it finish in 100% and than go to three color boot screen? ....
Hi alebo caf Vašek ;-)
My problem is that always stuck on boot image HTC or Windows Mobile blue screen. I can´t use way copy necesseary files to root of phone memmory and than run sspl etc...I have to turn manualy to three-color mode, than connect USB cable and run upgrade utility but still froze instalation on 2%, If I use SD card methode with BREEIMG file uploading doesn´t start....
p.s.: Ak by si mal dáku radu tak možno lepšie vysvetliť po česky ;-). Moje ICQ 208-393-971
Dík
CZ Rom
I would like to install new ROM into my Mteor, but I have no experience doing it. I do not know which version to try, all I need is to be able to enter czech letters on HW keyboard as with original ROM. Any sugestion? I preffer personal answer in czech language ([email protected])

After flash, still boots to bootloader..

Hi,
I successfully HardSPL'd my 8125 G4 a few weeks ago, then loaded NBD8.3 rom.. its been awesome.
Yesterday, the phone booted and shows the spash screen, but then boots back into bootloader.
I tried to reflash NBD and a few other roms again, they flash successfully, but it still boots into the bootloader.
I tried to hardSPL flash my phone, but that says it cant connect to the device (but the RUU connects and flashes fine)
Whats my problem??
Thanks
I tried to use mtty1.42, the instructions say to use USB and not COM1 or COM2, but I dont have USB in the drop down box??
please help!
Thanks!
Hello together, maybe someone can give me a hint.
after flashing my wizard it always boot´s into the "red green blue" screen. I tryed different tools and roms and its possible to install a new rom.
the "pda phone rom update utility 2.00.1" always says
congratulations.. update successfull.. etc.
but after reboot the wizard again comes into the red green blue screen. arg
ipl 3.08.001
spl 3.08.0001
thanks for your help
Hello,
Wizard_Love_2.26.10.2_WWE_Novii_CF2 did the Job. The Updater is italian (i guess) but the rom i english.
Thanks to all who post here a lot usefull thinks!!
search, try & error did the job.
how to exit bootloader
I flashed wizard 200 it was succesfull but now it is stuck with bootloader mode. hard reset won't work.
I know that battery died right after flash and now i can't charge it or exit boot loader.
Any idea, except waiting 20 days for new battery?
all the best!
XDAMON said:
I flashed wizard 200 it was succesfull but now it is stuck with bootloader mode. hard reset won't work.
I know that battery died right after flash and now i can't charge it or exit boot loader.
Any idea, except waiting 20 days for new battery?
all the best!
Click to expand...
Click to collapse
Men, it happen to my the same thing.
100% battery charge before start, but it dies after the procedure... No spare battery, No external charger, No charge on boot loader mode... "touchè"
We have a very functional smartphone before, but now we have a beatiful grey brick with a 3 coloured screen.
That`s not all... if you ordered a new Baterry, if it`s not stolen by the postman, when it reaches to you let`s pray that is in good shape...
Men, we cant do anything but wait... and the wait is killing me.
The alternative is a home made battery with 3 AAA batteries, but i will left that to Mc Gyver.
I ordered battery charges as well
Will post result in 2-3 weeks when I get it finally.
Any other (buttons) trick?

Bricked Diamond(can still get to bootloader)

I loaded a Custom ROM on my Diamond using The Active Sync
When the flash finished the Touch Flo screen came up then
The Red text to the bottom right comes up.
After that nothing else happens.
That ROM was the third ROM I flashed because One I got tired of
and the other was messing the phone up.
I have Hard SPL Olinex 1.43 Is there anything I can do to fix it?
I can still put it Hard Reset mode and reset it but it Just shows me the
TOuch FLo Text and the ROM info
How do I restore it with MTTY
This is the bit you need:
http://forum.xda-developers.com/showpost.php?p=4194865&postcount=4

Stuck in Bootloader screen

Hello all,
as the title says, one of my touch diamond's is stuck in bootloader screen.
I didnt do anything in between it working and not working, it was on my desk, put it there working, got it 5mins later, and it was in bootloader screen (tricolor screen).
What i've already done to try and fix it:
flash it with the original HTC rom, flash completes succesfully, phone reboots to tricolor screen, so no solution there.
install mtty and format the phone, this completes, reboot the phone, again goes to the bootloader.
reflash the phone with original rom after cleaning it with mtty, flash again completes succesfully but when it reboots after flashing it just goes to bootloader again.
Tried to flash a Hardspl: stuck at 0% and stays there. so that doesnt work.
BUT! when in mtty i give the "boot" command, it DOES start to boot WM. but then again, when i turn the phone of, and on again, or it reboots because of first start after flash, it goes to bootloader again. The VOLDOWN button is NOT stuck, cause when it boots i can use the vol buttons perfectly fine.
Anyone got an suggestion in how to unbrick it? i have a second, perfectly working diamond here too, if that helps in any way.
Some more info ive just seen in mtty, when i told it to boot, it said ONE BAD BLOCK IN CE, remove block ---- to ---- (dont know the exact numbers anymore)
hi..i had something like that...
just download this.
"RUU_Signed_1_93OliNex_HSPL_UnsignedEdition"
it's only 1.7MB and it's will make it work.. atleast it did the job for me...
Hi,
My T mobile touch diamond stuck in bootloader screen? Any experties to help me please.
Thanks in advance.

Categories

Resources