Hello all,
first let me apologize for the long post, and my noobiness. I'm new to the smartphone world, I've sucessfully flashed my Kaiser (from work). Also, I would like to thank everyone who is cooking!
I have the HTC Mteor, which I'm trying to Flash to WM6.1.
When I got it (used), I did a hard reset, and it went back to WM5 in Russian.
I believe I successfully unlocked it, and can now get to the tri-color screen.
It reads:
BBEE100
IPL-0.90
BREE100
SPL-2.05
Every ROM (including the original from HTC) opens, forces the phone to the tri-color screen, and then dies. Error 260, 262, etc.
I've searched the forums, and read that the SPL should be 1.10, but I can't get that to install either.
Any help/suggestions?
Thanks,
Jeff
jjmorris100 said:
Hello all,
first let me apologize for the long post, and my noobiness. I'm new to the smartphone world, I've sucessfully flashed my Kaiser (from work). Also, I would like to thank everyone who is cooking!
I have the HTC Mteor, which I'm trying to Flash to WM6.1.
When I got it (used), I did a hard reset, and it went back to WM5 in Russian.
I believe I successfully unlocked it, and can now get to the tri-color screen.
It reads:
BBEE100
IPL-0.90
BREE100
SPL-2.05
Every ROM (including the original from HTC) opens, forces the phone to the tri-color screen, and then dies. Error 260, 262, etc.
I've searched the forums, and read that the SPL should be 1.10, but I can't get that to install either.
Any help/suggestions?
Thanks,
Jeff
Click to expand...
Click to collapse
install this official rom from HTC
http://rapidshare.com/files/66085556/RUU_BREE100_1.34.261.1_1.38.00.10_HTCRUS_SHIP.exe
Its for RUS QTEK_AO7.
Then you will have SPL 1.10
I have similar problem
I had ROM 6.1 from Futureshock...still problem with radio (my phone couldn´t accessble but signal icon shows good signal, radio version 1.38.0000), so I decided flash some original ROM. Aftet that my booting stuck on HTC logo or Windows Mobile logo. So I can´t use normal way to flashing. Only from SD card or first turn on phone to boot loader mode and than attach usb cable and start flashing. From SD card (where is renamed ROM BREEIMG.NBH) after enter into bootloader mode start loading and than just turn to trhreecolour menu where is BREE100 - IPL-0.90 and BREE100-1.10.0000 and doesn´t want continue. If I flash ROM via USB cable (first go to threecolour mode, than attach cable) than run ROMUpdateUtility.exe and flash process is being started but always die on 2%, than autoreboot and again stuck on HTC logo.
I tried soft reset, I tried lot of ROM versions HTCRUS, HTCEUR, QTEKEUR, FUTURESHOCK but still same problem during flash ROM stop on 2%...
Any ideas how to back life to my MTeoR?
Can I use application like MTTY? Could me help this program?
Thanks for any help...
hi, can any1 send me a link for a ger version of wm6.0pro ?
Wigo said:
I had ROM 6.1 from Futureshock...still problem with radio (my phone couldn´t accessble but signal icon shows good signal, radio version 1.38.0000), so I decided flash some original ROM. Aftet that my booting stuck on HTC logo or Windows Mobile logo. So I can´t use normal way to flashing. Only from SD card or first turn on phone to boot loader mode and than attach usb cable and start flashing. From SD card (where is renamed ROM BREEIMG.NBH) after enter into bootloader mode start loading and than just turn to trhreecolour menu where is BREE100 - IPL-0.90 and BREE100-1.10.0000 and doesn´t want continue. If I flash ROM via USB cable (first go to threecolour mode, than attach cable) than run ROMUpdateUtility.exe and flash process is being started but always die on 2%, than autoreboot and again stuck on HTC logo.
I tried soft reset, I tried lot of ROM versions HTCRUS, HTCEUR, QTEKEUR, FUTURESHOCK but still same problem during flash ROM stop on 2%...
Any ideas how to back life to my MTeoR?
Can I use application like MTTY? Could me help this program?
Thanks for any help...
Click to expand...
Click to collapse
I'm not sure that I understand well, but if you flash from SD, it finish in 100% and than go to three color boot screen? ....
Hi alebo caf Vašek ;-)
My problem is that always stuck on boot image HTC or Windows Mobile blue screen. I can´t use way copy necesseary files to root of phone memmory and than run sspl etc...I have to turn manualy to three-color mode, than connect USB cable and run upgrade utility but still froze instalation on 2%, If I use SD card methode with BREEIMG file uploading doesn´t start....
p.s.: Ak by si mal dáku radu tak možno lepšie vysvetliť po česky ;-). Moje ICQ 208-393-971
Dík
CZ Rom
I would like to install new ROM into my Mteor, but I have no experience doing it. I do not know which version to try, all I need is to be able to enter czech letters on HW keyboard as with original ROM. Any sugestion? I preffer personal answer in czech language ([email protected])
Today I flashed my device to L26 KaiserDiamond from a WM6.1 Dutty's ROM.
The device rebooted fine, but when I tried to restore contacts/notes/etc.(via Sprite Backup), it performed the operation normally, but after restarting it is now stuck at the HTC logo.
I tried to reset the device via a hard reset, and it doesn't even get to the HTC logo... it just hangs at the L26 flash screen with the version numbers.
Is there anything else I can try, or do I have an excuse to buy an iPhone now?
Have you tried to re-flash it?
I'd put it in bootloader mode and re-flash.
good luck
try taking the battery out of your phone
after several times trying to unsuccessfully install a hard spl. (it installs and on reboot keeps the version 3) i upgraded the radio and now its stuck on the htc loadup sreen with the version listed on the bottom . a hard reset just resets so i cant even run the repair utility
one more thing
Oh and one more thing because it wont boot full or go into hard reset mode the computer will not recognize it.
It had a Chinese ROM and I wanted it in English, after flashing the ROM I wanted, it restarted and would not get past the startup screen.
Phone: Dopod s900 with WM6.1
Soft reset: ends up at startup screen and then stops
Hard reset: same thing happens
Bootloader: coloured screen, can't do anything
I tried to flash again in the coloured screen (bootloader?) and when it showed my current image, it was blank. Does this mean I have nothing in my phone right now? None of the flash ROMs I'm trying to install right now are working.
I don't know what to do...is it broken?
salenasg said:
It had a Chinese ROM and I wanted it in English, after flashing the ROM I wanted, it restarted and would not get past the startup screen.
Phone: Dopod s900 with WM6.1
Soft reset: ends up at startup screen and then stops
Hard reset: same thing happens
Bootloader: coloured screen, can't do anything
I tried to flash again in the coloured screen (bootloader?) and when it showed my current image, it was blank. Does this mean I have nothing in my phone right now? None of the flash ROMs I'm trying to install right now are working.
I don't know what to do...is it broken?
Click to expand...
Click to collapse
In the colored screen does it say "serial" or "usb" near the bottom?
If it says serial try to plug in the usb and if it changes and then says "usb" you should be able to re-flash the rom.
Thanks,
It says usb because I have it plugged in but which rom am I supposed to use? Its very original one? The one in Chinese? because I can't even find it..and I want it to be in English. What made it freeze in the first place was because i tried to flash a cooked rom. Will my phone work again after I flash a new ROM?
Thank you! It worked <3
Hi i get one HTC Touch Diamond blocked on XDP Diamond Logo,i try to reset with hard reset but i cant put in reset mode,so have any method to reflash because i'm new with HTC Phone thanks
Your only solution seems to be flash a new rom.
This guide should help you do just that.
Make sure your device is at the bootloader screen and connected to your computer before you run any of the executables. To boot it in the bootloader screen just turn the device on while holding the volume down button. Then enter the usb cable when the word 'Serial' appears on the screen and open the ROMUpdateUtility executable when the word 'USB' replaces 'Serial'.
Goodluck! Make sure to flash the Hard Spl first if you have never flashed a custom from before. There is no need to flash a radio, so you can skip that step if you want.
Goodluck and be very careful!
EDIT: If you have some problems or questions about the process or anything send me a message! Because if you post it here I probably won't see it.