[Q] Question about cracks - XPERIA X1 Q&A, Help & Troubleshooting

So I know that the X1 is known for having cracks. And unfortunately my x1 is cracking as well.
I was wondering how badly your x1 cracked up. Did anyone's x1 actually crack up to the point that it's not usable?
I'm asking because to cut a long story short I either change to a new phone this winter or wait until summer. And I want to know how much longer my x1 can last.
Thanks for the feedback.

no mine one didn't crack to that point actually I think that it is impossible for it to crack to that point unless you drop it or throw it on purpose xD and only cracks around screws can be a problem because then that point isn't locked down propertly so it can easly fall apart if it cracks around two or more screws but that is impossible because the plastic is to thick around then xD

The thing is mine is cracked and the part where the camera button is seems to be splitting open, it's hard to explain but it's like there's a small gap where if you push the phone together will close the gap. The same thing is happening just below the volume buttons too. I'm worried that this gap may get bigger.

time will tell xD that plastic above the camera button can easely be removed and you'r one isn't secured so you can remove it and place it back again it will fit back better

Related

Question about the sliding mechanism

Hi there,
when my Kaiser is closed there is a gap between the Screen and the keyboard.
Not a big one its 1mm thick.
Is it normal or is it a sign that my sliding mechanism got broken?
and i wuld like to know if there is a way to fix it, or if someone knows a german repair service
Thanks
Mine has a gap but I don't know about a millimeter, how big is that again? As thick as this I? I think that if they where touching then it would create friction and after a while the plastics would grind and wear away.
I have mine about 5 months or so. It has a small gap on both sides of about 1 mm thick but it is still solid in place. I mean there is no friction or so. I think there is nothing to worry about exept when you can twist or move the screen when closed. Then I would check the sliding mechanism.
JeckyllHavok said:
Hi there,
when my Kaiser is closed there is a gap between the Screen and the keyboard.
Not a big one its 1mm thick.
Is it normal or is it a sign that my sliding mechanism got broken?
and i wuld like to know if there is a way to fix it, or if someone knows a german repair service
Thanks
Click to expand...
Click to collapse
I have mine about 5 months or so. It has a small gap on both sides of about 1 mm thick but it is still solid in place. I mean there is no friction or so. I think there is nothing to worry about exept when you can twist or move the screen when closed. Then I would check the sliding mechanism.
Click to expand...
Click to collapse
Thanks same like mine.
is it normal, too that i an whipp the screen a little when its closed.
Not mouch just a little when i tap on the rigth or the left side of the screen.
Mine also has a very small gap (not a mm though)....

Keyboard scratches!

Hello everyone.
I noticed my keyboard gets scratched, more on the right side, keys "del", "enter" and "ok".
Does anybody else have the same problem? I'm not using that keyboard a lot, so probably those who use it every day should get even worse results...
A friend of mine doesnt use it much too but got these scratches also...
i got one on the enter key. dont know where i got that one. maybe i got some little dirt whatever stuff in my pocket and it went into the x1 and when you slide it up it does that scratches :/
Holy crap what the heck do you do to your Xperia!!!!?
lol i use mine 24/7 and mine is like brand new except for the battery cover, had mine for a few months too
alex_mib said:
Hello everyone.
I noticed my keyboard gets scratched, more on the right side, keys "del", "enter" and "ok".
Does anybody else have the same problem? I'm not using that keyboard a lot, so probably those who use it every day should get even worse results...
A friend of mine doesnt use it much too but got these scratches also...
Click to expand...
Click to collapse
The most likely reason for this damage to the keyboard is using acetone or maybe even alcohol to clean the keyboard....
poetryrocksalot said:
The most likely reason for this damage to the keyboard is using acetone or maybe even alcohol to clean the keyboard....
Click to expand...
Click to collapse
Again, I'm almost not using hard keyboard.
I usually keep the phone in front jeans pocket, looks like smth inside scratches it, but i dont wanna disassemble it to find out =)
not only is your x1 scratched but its dirty.
My one is worse!
I will upload some pictures later as I am off out today
What causes this
I use my phone alot but surely it shouldn't happen?
poetryrocksalot said:
not only is your x1 scratched but its dirty.
Click to expand...
Click to collapse
it is not dirty, i tried to remove that, but no luck - those are scratches!
I've got scratches on the windows key and the enter key
Never heard of or saw these types of scratches on the keyboard. Wow.
wash ur fingers before u use it
if u have dust or sand-like stuff on ur hand it will act as a sand paper
and apply less force when sliding ur phone apart
take care
Lol I would never touch your Xperia, it looks ****ing dirty Man, what are you doing with this phone?!? Gardening?
Obviously people don't know how to take care of their stuff. Word of advice, don't have kids.
hey, it looks like a "cracks in the case" case
Manufacturing defect
I don't know what you put in your pockets, but your X1 keyboard looks really dirty (especially with the wood piece under the blue key). I have some dust on my keyboard because it's in my left front jeans pocket the whole day, but this dust just goes away if I blow on the X1. If something don't goes away, use a dry soft tissue, or the humid tissues used to clean camera lenses.
the second pic clearly shows marks that clearly states that your x1 received torture dude, whether it be dropping or rubbing against something rough, it also shows something looking like dirt(mud) including dust on the board surface.
it looks as tho the phone fell many many times whilst the slide was out and possibly dragged on that surface on some kinda object
poetryrocksalot, i have 3 kids ages 6,5,3 lol, and my stuff are in tip top shape
scratches do not appear just like that, its impossible for scratches to appear out of the blue...in other words, your x1 clearly shows bad handling and money wasted on a device that deserves an owner who knows how to care their devices.
the only scratches im gettin is on the battery cover
my x1 got it too but just on the enter button... not as bad as yours but anyway... had mine for 6 or 7 months now... i think i know how the scratches get there and sorry for my swenglish... when i push the i dont know what to call it.. .lets call it the display to reveal the keyboard i put my thumbs on the bottom of the screen and push upwards but at the same time i push it slighty down and therefore i get the scratches try it and you will see how it touches the enter button...
I won't be able to sleep....... ever.......

Mother of fail: battery cover?

I just realized how difficult it is to open the battery cover after you've inserted the battery. Anyone having trouble with it or am I just a huge failure? I don't want to push and wrench away at it in fear of breaking the thing, what with it being plastic.
grainysand said:
I just realized how difficult it is to open the battery cover after you've inserted the battery. Anyone having trouble with it or am I just a huge failure? I don't want to push and wrench away at it in fear of breaking the thing, what with it being plastic.
Click to expand...
Click to collapse
Try applying pressure nearer to the bottom of the phone and push away from you. You scaredy cat
Yeah, you have to apply pressure at the right place (at the center near the bottom) but it can be really difficult to open sometimes. At first I thought I'd get a spare battery to be able to switch when one is empty, but I can't see myself opening the phone every other day, I'm pretty sure I would break it eventually...
Stea1thmode said:
Try applying pressure nearer to the bottom of the phone and push away from you. You scaredy cat
Click to expand...
Click to collapse
Every time I apply pressure it makes this sound like it's about to break. D: And I keep getting the feeling I'm going to crack the screen. I'll flash damn near anything all day long, but breaking the thing physically scares the daylight out of me.
No success, btw. Either I'm not pressing in the right place or not pressing hard enough. Swear to god I opened the thing multiple times the first day I got it (after the battery was in, no less) since I got the SIM card in the wrong way. Now it's tight as... well, very tight. Plastic isn't supposed to expand, damn it.
grainysand said:
Every time I apply pressure it makes this sound like it's about to break. D: And I keep getting the feeling I'm going to crack the screen. I'll flash damn near anything all day long, but breaking the thing physically scares the daylight out of me.
No success, btw. Either I'm not pressing in the right place or not pressing hard enough. Swear to god I opened the thing multiple times the first day I got it (after the battery was in, no less) since I got the SIM card in the wrong way. Now it's tight as... well, very tight. Plastic isn't supposed to expand, damn it.
Click to expand...
Click to collapse
the trick is to handle the phone at its sides, that way you wont risk breaking your screen. So apply preesure at the sides of the battery door and push with both thumbs.
Here's how to do it properly.
Hold the phone, using both hands, between index fingers and thumbs, so that the thumbs are just above the silver (engraveable) strip in the back. Bring the thumbs in toward the center line of the phone.
Angle your index fingers a bit, so that the pressure is applied not at the screen but the edges of the device. Curl the index fingers so that the upper half of the fingers are pointing toward your body and are positioned alongside the edges of the device.
Now, with your thumbs, push in and up. It helps if fingertips are nice and dry
I get the very same feeling of just how fragile it seems to be when trying to pop the cover off
This is not a problem I've ever had. It just slides off; what the heck are you people trying to do to your poor battery covers? ^_^
danguyf said:
This is not a problem I've ever had. It just slides off; what the heck are you people trying to do to your poor battery covers? ^_^
Click to expand...
Click to collapse
Harry, it's only a problem for the original poster
Guess I'm just a clumsy ****. It kind of moved a little bit when I tried what you guys said, but otherwise unless I'm willing to go at it with my nails, I should probably ask someone else to do it.
On the other hand, no dust under my screen! The tightness of the battery cover might as well be why.
I find sticking your fingernail in the little slot where the speaker is and dragging back from there helps. I also get the feeling im going to crack the screen when im pressing hard on the phone, its scary stuff!
Try this, hold your phone in your left hand facing down with your index finger and thumb just on the sides of the phone just above the capacitive buttons. Then place the ball of your right palm on the back of the cover and push up while applying a little force, it should open pretty easily.
nDrg said:
Try this, hold your phone in your left hand facing down with your index finger and thumb just on the sides of the phone just above the capacitive buttons. Then place the ball of your right palm on the back of the cover and push up while applying a little force, it should open pretty easily.
Click to expand...
Click to collapse
YES. This did the trick fantastically. It seems so simple now, I've no idea how I kept doing it wrong.
? You've read P 18 of the user guide ?? Nice wee diagrams... they work for me...
http://www.google.com/googlephone/nexusone-userguide.pdf
(In other words, RTFM ?? - no offence intended ...)
Cheers!
Lodger
I rarely, if ever, read manuals. But it's not as if I had trouble removing the battery cover the first day (especially since I had to do it several times as my SIM card was inserted the wrong way in).

DIY GUIDE TO REPLACING THE 19$ BROKEN GLASS on the galaxy note

hi folks. i managed to replace my galaxy note front glass with a new one i got from ebay for 19$ and i want to make a step by step guide on how it can be done.
i did it using common tools and a s load of pacience and attention.
the tools i used are: heat gun with hi and low settings, exacto knife set,small phillips and flat screwdrivers, goo gone, and optional a screen protector.
first take the phone apart as it's describet in countless of threads and youtube videos. you should end up with the screen assembly shown in the first picture.
now we have to separate the glassscreen from the frame it sits on. for this we fire up the heat gun.
a few words about using the heat gun.
-my gun had 2 settings: low and high. during all this process i used it on low.
-don't put the gun directly and/or close to the thinn plastic wires that hold the two connectors.
- dont hold the gun in the same place more than 3 seconds, instead swipe the gun around the spot and the screen like u would do with a paint brush when painting.
- dont hold the gun too close, that is closer than 3 inch
-concentrate on the spot u working at but try to heat up the whole screen assembly, as it has to give away from all the points kind of at the same time, and not just the point u working at.
- dont overheat the screen as this will damage the amoled. thats how i got the two yellow spots on my screen. first one by accident and second one intentionaly to see if indeed the overheating is what caused it.
A very good rule for this is dont heat the phone more than you can bear to touch it cause afterall you have to hold the phone while working on it...
the way i did it is :
-i heated up the whole screen assembly, back and front, for a minute or two
- than i started to stick the tip of the exacto knife between the glass and the metal edge that sorrounds it. i started from the upper right corner, the side where the front camera is. see photo 2.
the goal is to unstick the glass from the frame. in photo 3 the frame and the screen is shown without the upper glass. this photo was taken after i finished everything, thats why the screen can be seen inside the frame. but i posted it to show the black sticky tape that its used to hold the glass to the frame. i think is the same kind of sticky tape thats used in all the touchphones including iphone to hold the front glass to the rest of the phone. in photo 4 i unsticked some of the tape to show it better. this tape is the main thing that holds the the glass to the frame. the other thing that hold the screen to the frame is some sticky glue on the back of the screen. but this is much softer and thiner glue. this is the reason why i say to heat up the whole screen assemby including the backside, to make it easyer to unstuck the glass and scren thats glued to it.
- once you get a bit of a foothold in the upper corner between and the glassand the frame you continue the folowing procedure again and again until the glass and screen detaches from the frame:
-every 2 minutes or so , when i feel the asemby cooled down, i'd heat up the whole assembly for 5 seconds or so, than concentrate on the spot i worked on for another 5 seconds, than move/push the exacto knife a bit. dont force it. after a while youl get a feel of it. if the exacto knife happend to be out, i would heat up the blade after heating up everything else, and than put the blade in.
prevent the freed parts from sticking back to the frame by using the rest of the exacto knife blades as shims.
once it detaches it should look like photo 5- the glass glued to the screen.
- now we have to detach or unglue the glass from the screen.
procedure is the same: start somewhere, heat, put knife in, etc... i used a second knife as shim folowing the first knife, and after avery couple moves i would get the knife out and wipe off the epoxy glue. heat the blade and put it back in.
when finished you should have something like photo 6 and 7: free screen covered in glue epoxy residue.
- now we have to get rid of the glue residue. i took the bulk of it usinga flat exacto knife blades like the one in photo 8 and 10. just warm the place a bit with the air gun and scrape it off with the blade. to clean what was left i used a bit of goo gone on a pice of cloth or napkin photo 9.
cleaned screen can be seen in photo 11 - sadly out of focus.
if u are like me and r impatient to test the screen you can just connect with just the side connector like in photo 12 and 13. the upper connector is for the s pen digitizer. side connector is for the screen and touch digitizer.
now all that's left is to put the phone back together except leave the new glass for last.
-first thing is to put the screen(without the glass) back on the frame. try to center it just right, so that ther's a little bit of space between the sides of the screen and the frame.
at this point all that will hold the screen to the frameis the thin layer of glue on the back of the screen. after centering and lowering the screen in the frame procede to put the phone back together folowing in reverse order the same steps used to disasambe it. when finished you should end up with the whole functioning phone except the front glass -as seen in photo 14.
now you can chose to trim and put a screen protector on the scree so as to fill the empty space between the screen and the glass - the space where the glue was, or you can just leave it empty. you can put a screen protector anytime after by removing the glass. which should be much easier to remove now that its held in place only by the blach sticky tape on the edges. just use some suction cap to remove it, starting at an age, and remove it like fliping a page. see photo 16. i used the note for 2 weeks without the screen protector in the empty space and it worked without a problem onlt thing was that when i pushed hard the glass would touch the screen and leave a bit of dirt in that place. thats why i decided to put the screen protector to fill the void. in photo 15 i raised the screen protector to make it visible in the photo.
if you are like me and worry that somehow the glass might fall off the phone you can always get a hard plastic case for the phone, like the one in the pics. it's made of 2 parts. one goes on the back one on the front and they snap togeter around the phone. this will hold the glass in place no matter what while it will also protect the phone.the case is in photos 17 and 18. i got this one of ebay for 8$ and free shipping.
the last thing to be done is:
for some reaseon the touch screen became much more sensitive after removing the glue so you need to lover the touch sensitivity. for this get the touchscreentune app from the market. it works with galaxy note and galaxy s2. put the sensitivity from the recomended 25 to 50.
the best thing about this procedure is that i dont have to worry about the f ing glass anymore. if it brakes again i'l just order another one and in under 2 minutes i can replace it. all i have to do is get the phone case off, put a suction cap on , , remove the old glass , and put the new glass. that's it.
because it takes 4 to 8 hours i would recommend the process to be done in 3-4 sessions as people would get tired after 2 hours of work and tend to lose focus, attention, patience and start to push to get it faster done, and that's when bad stuff happens like yellow spot burn on the screen or small scratches. another thing about scratches, even if u manage to scrach the screen dont worry to much as the scratches are almost invisible when the screen turns on. youl see what i mean ....
i do have one question: WHY DID SAMSUNG DECIDE TO GLUE THE SCREEN TO THE GLASS INSTEAD OF HAVING THEM SEPARATE LIKE ALL THE OTHER TOUCHPHONES?
I do the same for Galaxy S. I removed broken pieces of glass from device using guitar pick and carefully glued a new glass on each side. 9$ (free delivery) on ebay.
blank for future use
blank for future use
anonymous572 said:
I do the same for Galaxy S. I removed broken pieces of glass from device using guitar pick and carefully glued a new glass on each side. 9$ (free delivery) on ebay.
Click to expand...
Click to collapse
what kind of glue did you use? where did u get the glue from? how did u do it?
i didnt glue the glass back to the screen. i just put the glass on the frame. to fill the void where the glue was i trimed a regular screen protector and put it inbetween the glass and the screen. but it works same without it.
Very interesting, I didn't think it was possible because the glass is glued to the SAMOLED panel. I'm very glad that I am wrong.
As much as I hate to think about it, a guide like that would probably come in handy for many of us at some point.
*knocks on wood*
pboesboes said:
Very interesting, I didn't think it was possible because the glass is glued to the SAMOLED panel. I'm very glad that I am wrong.
As much as I hate to think about it, a guide like that would probably come in handy for many of us at some point.
*knocks on wood*
Click to expand...
Click to collapse
Nothing is impossible with the right tool and know-how . The glue could probably be uncured with a heat gun, just like ipad. The challenge is not damage the panel and make sure it is dust free after put back the replacement.
It is said impossible because of the difficulty involved. If you can't manage to install a screen protector with perfect alignment and zero dust spike, this task is not for you.
@drevilatwork Thank you for writing this step by step guide!
I dropped my phone last night and it landed face down, cracking the glass.
I'm so upset, but I don't think I have the skills or the tools to do this job myself. I am relieved to learn that the glass can be replaced, but do you know whether the Samsung agents are likely to be able to do this?
they probably wont do it. but you can try showing this thread to some technician or phone repair shop and they might do it for you. they also might charge you a lot to the point where it might be more convenient to just buy a new 260$ screen.
looks scary dude
all im going to say is good luck separating the 2 screens without breaking the lcd or scratching the crap out of it ... this is a 90% epic fail method but thumbs up to the few that may succeed or dont mind their screen looking like its been belt sanded...
Its worth a try, since screen replacement costs 230 euros.
kawgirlval69 said:
all im going to say is good luck separating the 2 screens without breaking the lcd or scratching the crap out of it ... this is a 90% epic fail method but thumbs up to the few that may succeed or dont mind their screen looking like its been belt sanded...
Click to expand...
Click to collapse
actually .. the funny thing is that even if u manage to screch the screen and / or leave dirt behind it doesn't show while the phone is on. it might show when is off but not when is on. i was suprised about that too. and secondly, having to do it again knowing what i know now i would do it without leaving a mark. and in the end is certenly worth a shot before ordering the 260$ screen assembly. the special thing that it requires is pacience and attention.
Why different prices for all the same lenses in this shop ?
drevilatwork said:
actually .. the funny thing is that even if u manage to screch the screen and / or leave dirt behind it doesn't show while the phone is on. it might show when is off but not when is on. i was suprised about that too. and secondly, having to do it again knowing what i know now i would do it without leaving a mark. and in the end is certenly worth a shot before ordering the 260$ screen assembly. the special thing that it requires is pacience and attention.
Click to expand...
Click to collapse
as i said good luck with it and hope you make some money doing it..... ive successfully done the same thing myself but other than it will never look good like a factory screen (not even close), the amount of time it takes to make it look anywhere near acceptable (not like a 10 dollar repair) is big and that makes the repair not really worthwhile doing it for anyone but yourself and even then who spends 700-800 dollars on something and does a repair that makes it look cheap... then theres the whole ordeal of the membrane youre taking the adhesive off of along with the HUGE chance of damaging it.. it is placed with precision and adhered for a reason along with being dust and scratch free... this is a repair that just wont last because things will start functioning improperly for multiple reasons...
im not knocking you or anyone who tries this..im just trying to emphasize the dangers, downfalls and the probability of it being a legit solid repair. also the resale value when the next greatest thing comes along... just beware....
Hmmmm
Well chaps I hate to disagree here, but after speaking to the technical bods at Samsung it appears that the OLED is NOT glued to the glass, but the glass is laminated and bonded in, much like a car windscreen. My screen got broken the other day and I have read the 2 posts on XDA regarding this. Now if you go and have a look at the pics of the other post
http://forum.xda-developers.com/showthread.php?t=1487716
you can clearly see the OLED, although broken, seperated from the glass with no sign of any glue. The reason it broke is that upon heating the glass you will melt the glue, which will then stick to the edges of the OLED and if you pry it at the wrong place/time/too hard/whatever you will break the OLED as it is glued to the bezel itself. So when my glass arrives I am going to attempt to remove the glass using fishing line and pulling it between the glass and the bezel and OLED to release it, the same way as I used to remove car windscreens, and post the results here. I have also been told that the reason for the sticky "epoxy" mess that you encountered in this postis from melting the plastic on the back of the glass (which is the lamination!) by using too much heat.....I mean come on, a heat gun is a bit excessive!! Prying the screen out a bit at a time might work, but will surely end in tears, where as cutting the cold adhesive with a fine nylon cable, which wont scratch the OLED, might just work. I'll keep you posted on my results.
Just throwing an idea out there: maybe the adhesive would be easier to defeat when it's really cold, rather than really hot. I know a lot of adhesives become quite brittle when you put them in the freezer, superglue and epoxy for example. And the electronics/plastics of the display could be relatively fine with the low temps.
pboesboes said:
Just throwing an idea out there: maybe the adhesive would be easier to defeat when it's really cold, rather than really hot. I know a lot of adhesives become quite brittle when you put them in the freezer, superglue and epoxy for example. And the electronics/plastics of the display could be relatively fine with the low temps.
Click to expand...
Click to collapse
this is not one of them...i can guarantee this 100%
learn how a digitizer is made then you might see the light, and not just the light of white trash repair and failure...
ive explained it in great detail many times... and btw just because im a girl doesnt mean what im saying is wrong... 20+ years in the industry gives me sort of a clue as to what im saying..
im trying to help people avoid a long drawn out disaster and to waste $20(which is NOT gorilla glass) plus all of the other things they buy to try to make this a success which will never happen...
and fyi freezers, superglue and epoxys are big no no's...they are not used by any factory so there is another myth busted... they will just add to the destruction... 100% guarantee
kawgirlval69 said:
this is not one of them...i can guarantee this 100%
Click to expand...
Click to collapse
What do you mean? One of what?
learn how a digitizer is made then you might see the light, and not just the light of white trash repair and failure...
Click to expand...
Click to collapse
I know how a digitizer is made.
ive explained it in great detail many times... and btw just because im a girl doesnt mean what im saying is wrong... 20+ years in the industry gives me sort of a clue as to what im saying..
Click to expand...
Click to collapse
I had no idea you were a girl and I don't see why that matters. Experience is the industry is of course relevant, if your particular field in the industry was related to repairs. But I don't know if it is?
im trying to help people avoid a long drawn out disaster and to waste $20(which is NOT gorilla glass) plus all of the other things they buy to try to make this a success which will never happen...
Click to expand...
Click to collapse
The glass on the Note is Gorilla glass: http://www.corninggorillaglass.com/products-with-gorilla/full-products-list
and fyi freezers, superglue and epoxys are big no no's...they are not used by any factory so there is another myth busted... they will just add to the destruction... 100% guarantee
Click to expand...
Click to collapse
I didn't say factories use superglue or epoxy, or freezers for that matter. But the fact that factories don't use them doesn't mean it can't work for DIY repairs. Low temperature brittleness isn't exclusive to epoxy or superglue. Many, many glues (and other materials) have that property.
pboesboes said:
What do you mean? One of what?
I know how a digitizer is made.
I had no idea you were a girl and I don't see why that matters. Experience is the industry is of course relevant, if your particular field in the industry was related to repairs. But I don't know if it is?
The glass on the Note is Gorilla glass: http://www.corninggorillaglass.com/products-with-gorilla/full-products-list
I didn't say factories use superglue or epoxy, or freezers for that matter. But the fact that factories don't use them doesn't mean it can't work for DIY repairs. Low temperature brittleness isn't exclusive to epoxy or superglue. Many, many glues (and other materials) have that property.
Click to expand...
Click to collapse
i mean exactly what i wrote... as per your idea... this wasnt one that would work... my god man do i have to spell everything out for you???
obviously you dont know how a digitizer is made or you wouldnt have spouted the crap you have... bottom line
the girl part..well some dont think women know anything..its a culture thing.. but as for you not knowing if my particular field in the industry was related to repairs my god ive only said it multiple times in multiple posts... but since you dont like to read i'll say it again..20+ years board level factory trained.. motorola, audiovox, nokia, samsung... and this is a samsung forum so i think i have my tech qualifications covered here... again READING IS GOOD... work on that...
again you just dont read or have horrible comprehension because i never said the notes screen wasnt gorilla glass i said the $19 one wasnt... seriously every time you type something you dig yourself a deeper hole...
your superglue and epoxy blather just shows you dont have a clue and dont read... really they dont have any place in the screen/lcd part of diy.. its just trouble looking for a place to happen... now if the plastic housing needs repaired maybe but still not a top ten choice... if you had a clue you would know the proper adhesive to use... and its easily found... you are just too much...
seriously...just give it a rest... i wasnt bashing on you and have said it ive also said all im trying to do is help people not make a bad decision... and THIS IS A BAD DECISION...
you want me to play nice (which i really am..most other forums here would have totally lowered the boom on you for spouting crap... ive been really nice.. to keep it that way just go post somewhere where you can be productive... here youre not... im sure you have some great ideas but nothing you have said in this thread is remotely good.. sorry but it is what it is...
beep beep
kawgirlval69 said:
i mean exactly what i wrote... as per your idea... this wasnt one that would work... my god man do i have to spell everything out for you???
Click to expand...
Click to collapse
The sentence made no sense considering what it was replying to. Not my fault you were unclear/ambiguous.
obviously you dont know how a digitizer is made or you wouldnt have spouted the crap you have... bottom line
Click to expand...
Click to collapse
Ok?
the girl part..well some dont think women know anything..its a culture thing.. but as for you not knowing if my particular field in the industry was related to repairs my god ive only said it multiple times in multiple posts... but since you dont like to read i'll say it again..20+ years board level factory trained.. motorola, audiovox, nokia, samsung... and this is a samsung forum so i think i have my tech qualifications covered here... again READING IS GOOD... work on that...
Click to expand...
Click to collapse
Reading is very good, but you can't assume everyone in a public forum has read every single post of yours and remembers every detail. What isn't helping is the lack of proper punctuation and formatting which make your posts unpleasant to read.
again you just dont read or have horrible comprehension because i never said the notes screen wasnt gorilla glass i said the $19 one wasnt... seriously every time you type something you dig yourself a deeper hole...
Click to expand...
Click to collapse
Replacement screens are generally OEM parts.
It might appear I'm in a hole, but that's only because I live in Holland and am below sea level. I assure you I haven't done any digging.
your superglue and epoxy blather just shows you dont have a clue and dont read... really they dont have any place in the screen/lcd part of diy.. its just trouble looking for a place to happen... now if the plastic housing needs repaired maybe but still not a top ten choice... if you had a clue you would know the proper adhesive to use... and its easily found... you are just too much...
Click to expand...
Click to collapse
I wasn't suggesting to use superglue or epoxy, read it again.
seriously...just give it a rest... i wasnt bashing on you and have said it ive also said all im trying to do is help people not make a bad decision... and THIS IS A BAD DECISION
Click to expand...
Click to collapse
I get that, and appreciate your concern. However, you should understand that some people like to try things even when the chance of success is not very high. You seem to be one of us in that regard (you attempted repairs yourself too, right?), so I don't see why it upsets you so much.
you want me to play nice (which i really am..most other forums here would have totally lowered the boom on you for spouting crap... ive been really nice.. to keep it that way just go post somewhere where you can be productive... here youre not... im sure you have some great ideas but nothing you have said in this thread is remotely good.. sorry but it is what it is...
beep beep
Click to expand...
Click to collapse
I don't care if you play nice or not. I appreciate honesty. Now for some honesty in return: you're not helping in this thread.
All you do is say people's ideas are stupid without giving arguments that aren't arguments from authority. And I would very much appreciate it if you would stop misrepresenting my posts (intentional or not).

Dust under screen - possible to repair or swap screen with another one

Hi,
I ended up buying 3 Droid 4's before I found one I was happy with. So, I now have 2 spare ones:
1) Very nice condition but has dusk under the screen
2) Poor conditon, crackly phone speaker but nice screen
So, I was wondering whether to try and get the dusk from under the screen.
Or maybe I should try and swap the 2 screens around?
Or am I likely to end up ruining both of them, and I'd be better off just selling them both as they are?
Cheers
Once you detach the glue from the glue that's holding the glue in place for the back casing, the phone actually comes apart fairly easily. Though, putting the back casing back on, I've always found that the bottom edge will never sit flush again; easily trimmed off with a razor blade. Otherwise the edge will protrude and catch on things.
The dust might not actually be dust; while shopping for my LG Ally, I bought one that appeared to have dust behind the glass and opened it to clean it, only to find out that the inside facing was actually covered in weird pockmarks. It was the strangest factory defect I'd ever seen.
If it's fairly uniform "dust", you might have the same thing going on. One way to find out. You'll need T5, T4 and possible T3 screwdrivers/bits to break it all the way down to the screen.
The only things I'd say to really look out for:
There are two soft spongey adhesive pads that the keyboard-facing side of the mainboard uses to stick to the rest of the phone. Try not to tear these up when pulling the mainboard out. One is next to the power button, one is the same place on the opposite end. If you do rip up the one on the power button end, the button might not line up properly anymore (it barely does to begin with, thanks Motorola) and it'll be harder to activate.
Don't try to remove the screen glass from the bezel/frame unless you have a solid plan to reattach it. I've heard it's a real nuisance to get it to adhere properly again. Fair enough if the bezel is torn up but the screen is nice, just be aware that things may get really annoying.
I would say just flip the screens around. I replaced a digitizer in a Photon Q and it was a pain (still isn't working for me either).

Categories

Resources