[Q] Need suggestions on repairing silver trim - Galaxy S I9000 Q&A, Help & Troubleshooting

Hello Experts,
I had my phone on the drivers' seat between my legs, and of course, I go to get out of the car and it falls and hits the concrete. I have the zagg protector shield on it so my screen and back are still safe and clean.
The phone fell on the lower left corner of the trim and the upper corner. Both corners has abrasion on the trim and looks like it could chip off. I don't think the damage is worth trying to go about replacing the whole trim but I would like to know if it would be possible to some how sand out the cracked paint to smooth it out while keeping the same glossy sheen? Is there any special paint for this fix? Any other advice?
Thanks in advance.
Samsung Galaxy S GT-i9000M

Rashar said:
Hello Experts,
I had my phone on the drivers' seat between my legs, and of course, I go to get out of the car and it falls and hits the concrete. I have the zagg protector shield on it so my screen and back are still safe and clean.
The phone fell on the lower left corner of the trim and the upper corner. Both corners has abrasion on the trim and looks like it could chip off. I don't think the damage is worth trying to go about replacing the whole trim but I would like to know if it would be possible to some how sand out the cracked paint to smooth it out while keeping the same glossy sheen? Is there any special paint for this fix? Any other advice?
Thanks in advance.
Samsung Galaxy S GT-i9000M
Click to expand...
Click to collapse
Sanding it would dull the paint and it would just look dull grey. If you really want to fix it you should tape off everything but the trim (electrical tape should do the trick), sand the trim down until smooth, and apply two coats of chrome spray paint.
Not sure if all that is worth it for just a little scratch but you could try!
~Gregory

That sounds good. I will have to try that. Thanks.
Sent from my GT-I9000M using XDA App

Related

Scratches! help!

Ok am really! careful with my screen! but some how i have some little hair line Scratches! on my screen.. is there any way i can remove them safe? cheers
Should've put a screen protector immediately when you got it.
Sent from my SGH-I717M using xda premium
you may find adding a protector now will hide the scratches if they are small enough
They may be superficial. Did you try some good rubbing with a lint free cloth. I had no sp for the longest with no scratches
Sent from my GT-N7000 using XDA App
crackster said:
Ok am really! careful with my screen! but some how i have some little hair line Scratches! on my screen.. is there any way i can remove them safe? cheers
Click to expand...
Click to collapse
sadly NO, If it makes you feel any better my Note always has a case on and just once i removed it for 5 minutes, I manage to drop the phone on a concrete now my screen is scratched thank good the glass didn't break.
I have a scratch on my Galaxy Note also :/ I've only just had it for a week. I only noticed the scratch when I was about to put the screen protector on. I think it happened due to me showing my sister my phone, and she gave my phone to my TWO year old niece to draw on :/ I'm so upset and angry about it. I've dropped my HTC Desire HD many times and not a single scratch.
Moved To Q&A​
Please post all questions in the Q&A section​
I have a tiny little scratch on my note as well. Its no big deal because it can't be seen unless you direct it to the light at a certain angle but it still bugs me.
It seems like the scratch was made with the s pen as it has the pattern of something I had drawn when I was trying out the s pen.
I'll be getting a screen film soon to avoid any further scratches.
Sent from my GT-N7000 using Tapatalk
I got a 1mm deep scratch on my screen to
again always had a cover on it and when i took the cover off ... guess what .. it fell on its face and got the scratch.
Now i have the flip cover on it and wouldn't risk taking it off again.
As they mention : Gorilla grass is scratch resistant only.
Look up 'Displex' - it's the best scratch remover there is, and it's cheap too.
Sent from my GT-N7000 using xda premium
This isn't for the faint of heart....
I built scale plastic model airplanes for 30+ years until the bifocals & carpel tunnel made it impossible to hold an airbrush.
The clear plastic "glass" parts, if not packaged in a bag, can get scratched, screwing up a good looking model.
For starters, try some mild toothpaste. DO NOT rub very hard. It's glass, but you don't want to really screw it up...just in case. After toothpaste, try buffing it with a sheep skin cloth (chamois). Now this one will sound silly, but it works on plastic, clear future floor wax. I used it from time to time to fill the spider cracks where they didn't get the mold clean when they injected the plastic.
I haven't had to fix a gorilla glass/hardened glass screen, but I've used these tricks on my old windows phones & pda's after too many uses of the stylus.
I don't use a protector on either my streak, for over a year, or my note for the last 3 months. I don't understand how they are getting scratched.
p51d007 said:
This isn't for the faint of heart....
I built scale plastic model airplanes for 30+ years until the bifocals & carpel tunnel made it impossible to hold an airbrush.
The clear plastic "glass" parts, if not packaged in a bag, can get scratched, screwing up a good looking model.
For starters, try some mild toothpaste. DO NOT rub very hard. It's glass, but you don't want to really screw it up...just in case. After toothpaste, try buffing it with a sheep skin cloth (chamois). Now this one will sound silly, but it works on plastic, clear future floor wax. I used it from time to time to fill the spider cracks where they didn't get the mold clean when they injected the plastic.
I haven't had to fix a gorilla glass/hardened glass screen, but I've used these tricks on my old windows phones & pda's after too many uses of the stylus.
I don't use a protector on either my streak, for over a year, or my note for the last 3 months. I don't understand how they are getting scratched.
Click to expand...
Click to collapse
+1
Clear floor polish works on harder clear plastic. Never tried on glass. WOrth trying for $10 from local supermarket. And then put a cover on it
I'm lucky so far - only scratches have been on the screen protectors. But then I need to replace them - used up two so far, and good quality 6H ones too! Better than a scratched glass though - sorry to hear about that!

Nicks on glass fiber polyamide frame

Hi, i was wondering if you guys have any nicks or little pieces missing the polyamide frame? When i open the flaps i think my nail digs into the frame and acts like a knife and cuts it. There is plastic underneath the rubber layer of the frame. I wonder what i can use to fill that nick up and bring it back to normal it's actually bugging me. What's your Xperience? and any idea's on patching it up? lol Thanks!
if you're a real badass you can use some metal glaze then sand it down till it's flush with the frame again.
but that would take some seriously dextrous fingers.
Same here a little dent or nick, but nothing to write home about luckily. Hope you can make it acceptable for you again.
Sent from my C6603 using xda premium

Screen gap and dust/crud

OK so the top of the phone above the screen the gap there...yeah its full of dust and tiny pocket lint so I thought OK let me stick paper in there and fish that crap out...all it did was smear it and what I got out was minimal. It's just a pain to look at every time I need to look at the screen I can see the dust in between the gap. Anyone else having this problem ?
Note 4
You knew about this issue before you bought the phone. Get a can of dust spray and you good. Avoid sticking it in your pockets. Was pants with pockets pulled out so it clean if you do stick it in
NOTE 4
I wouldn't recommend spraying with air. I may just push dust inside phone and collect on front camera lens. What I did: I rubbed in a clear silicone into this tiny gap around screen and wiped it clean. Now im sure that no dust can enter inside. I was contemplating to use uv glue leftover from my note 2 screen replacement but is a little more messy to clean out than silicone (but is perfectly clear when cured).
BACARDILIMON said:
You knew about this issue before you bought the phone. Get a can of dust spray and you good. Avoid sticking it in your pockets. Was pants with pockets pulled out so it clean if you do stick it in
NOTE 4
Click to expand...
Click to collapse
Oh yeah I didn't even think about that. What if I just cut all the pockets out of my pants and then I won't even be tempted to put anything in there.
Note 4
Is it serious that simple to get dust under the screen do u have pics i debating on this phone hard
vinnyj85 said:
Is it serious that simple to get dust under the screen do u have pics i debating on this phone hard
Click to expand...
Click to collapse
Nothing under the screen just on the sides
NOTE 4
If the screen were fitted with no room for expansion and contraction of the metal frame it would butt against the glass tight and bind and possibly stress crack, most materials need clearance for this reason but I bet if you warmed your screen with a blow dryer and put force upward you could slide the glass on the adhesive, let it cool in place and with the gaps even all the way around it will look more normal to you, it will move I've done it on my s4 but try at your own risk me no responsible if you put too much pressure and break your glass, hope this will help.
My son and i must have gotten lucky i have no gaps anywhere no dust issues can post sreen shots if you want but mine is as tight as a ticks ass.
smccall said:
My son and i must have gotten lucky i have no gaps anywhere no dust issues can post sreen shots if you want but mine is as tight as a ticks ass.
Click to expand...
Click to collapse
No gaps in mine either. Mine is made in Vietnam. Where was yours made?

Yes, the black paint on the bezel will scratch :(

Just in case you were hoping that the body of this watch was a solid piece of black metal, it's not. If you bang the edge of bezel it will expose shiny silver metal. I know this because my desk at work is glass and I banged the bezel against it's edge when standing up. Nothing I couldn't improve with a little black magic marker. Sigh, oh well, nothing stays brand new forever.
P.S., Apparently no metal is black through and through. That being said, whatever they have used to "paint" this black is not very good and comes off easily.
mitchellvii said:
Just in case you were hoping that the body of this watch was a solid piece of black metal, it's not.
Click to expand...
Click to collapse
There is no such thing as "black metal" on this planet, yet. That material does not exist and has not been invented yet. Everything that is made out of metal is PAINTED (with different methodologies, but still, painted). No matter how you will create that paint (melted powder, dissolved material, laser) it will only be a thin layer at the surface of the metal. If you will scratch the coloured layer, the METAL under it will be revealed .
So, the hardness of a color on a metal surface it's given by the paint type and the method of applying it.
Yea.. I went to a shop and the promoter showed me a pretty banged up device.. with liver linings all over.
Does anyone know if the silver version is every gonna come out?
Huh gotta say I find this somewhat discouraging. Barely brushed the metal on the bezel of this watch against another hard surface and the paint came right off. Whatever method they used on this didn't work very well. The Zenwatch is suddenly looking more appealing.
Looked around and this seems to be the best repair item I've seen for fixing scratches on black anodized aluminum.
http://www.amazon.com/Birchwood-Casey-Super-Black-Touch/dp/B00BGH0Y0W/ref=cm_cr_pr_product_top
Of course not everyone loves it but most who know what they were doing seem to. Seems to work better than the old Sharpie solution because that dries very flat and you can see it.
This is why I bought a whole case plus screen protector for it.
You might want to consider doing the same.
wtf.now? said:
This is why I bought a whole case plus screen protector for it.
You might want to consider doing the same.
Click to expand...
Click to collapse
Yes but none of those kits protect the edge of the bezel which is the most likely place to get scratched.
mitchellvii said:
Yes but none of those kits protect the edge of the bezel which is the most likely place to get scratched.
Click to expand...
Click to collapse
Nothing will.
Until they make full case covers and that for sure will look like ****.
wtf.now? said:
Nothing will.
Until they make full case covers and that for sure will look like ****.
Click to expand...
Click to collapse
Actually a little adhesive black rubber ring to go right on that bezel edge would to the trick. Sort of a bump guard. That's really the only place you need to protect.
may be that the bezel can be easily changed
I thought that for the price it has to be DLC coated. The ZenWatch should be better, or at least cheaper to replace.
Hi
Do you know if it is possible to change the bezel ?
I banged my watch bezel against a painted wooden door frame today. It took paint off the door frame. But I wiped off the bezel and it was unphased by the event. You'd have to bang the bezel pretty good against something pretty hard to mess it up.
I rubbed mine on a metal surface, at first I saw a nice streak, rubbed it and my watch was fine.
Beware the edge of glass tables. As glass is very hard it will scratch the paint off your bezel with ease. I have a glass top on my office desk. Since I wear the watch on my left wrist, I've put a piece of black rubber electrical tape above where I tend to rest my hand on my leg. Now if I bang the watch on the glass table edge it is protected.
Darnell_Chat_TN said:
I banged my watch bezel against a painted wooden door frame today. It took paint off the door frame. But I wiped off the bezel and it was unphased by the event. You'd have to bang the bezel pretty good against something pretty hard to mess it up.
Click to expand...
Click to collapse
A dumbel during fitness
i was wondering if it could be replaced...
daigoro76 said:
may be that the bezel can be easily changed
Click to expand...
Click to collapse
Can it be replaced? I want to throw a diamond bezel on it.
klyles said:
Can it be replaced? I want to throw a diamond bezel on it.
Click to expand...
Click to collapse
It can't be replaced. But there's a thread in one of these "R" forums. Where someone shows in detail, how to file down the top part and looks nice.
Sent from my Nexus 10 using Tapatalk
Darnell_Chat_TN said:
It can't be replaced. But there's a thread in one of these "R" forums. Where someone shows in detail, how to file down the top part and looks nice.
Sent from my Nexus 10 using Tapatalk
Click to expand...
Click to collapse
What's so hard about taking a file to it? I just took my wife's nail file and filed the entire top ring off. Some dude, filed the entire thing. too.
Darnell_Chat_TN said:
I banged my watch bezel against a painted wooden door frame today. It took paint off the door frame. But I wiped off the bezel and it was unphased by the event. You'd have to bang the bezel pretty good against something pretty hard to mess it up.
Click to expand...
Click to collapse
I too have had some pretty big brushes with objects and the bezel has faired well in every case.

How to remove Glue from Edges-Frame

Hello gyuz,
As mentioned in another thread in Accessories sub-forum, while Installing the Whitestone Dome Screen Protector (https://www.whitestonedome.com/) on my Samsung Galaxy Note 8, there was UV glue spillage all around the phone & now I have dried (UV cured) glue in the tiniest gap between the screen edges and the metal frame of the phone. Please check attached image, I have circled with red the exact location of the glue, however imagine this almost all around the phone:
Now I need a good UV glue remover to soften the dried glue and an extremely thin blade (or a similar tool) to reach in the gap and remove it. I saw some products on ebay, however I am not sure which will do the job.
First of all which Glue Remover is more suitable? Does it have to be a branded one? Or the unbranded ones will do the job as well? Is there danger that the remover will dry and stay in the gap making it worse? Will it damage the color or consistency of the metal frame? Will it damage the buttons (Power, Volum, Bixby)?
Secondly, which tool should do the job reaching such tiny gap while at the same time not scratching the screen or the metal frame? Metal Blade? Plastic Blade? Wire? Some other tool?
Please advise, as I am nearly desperate. Thank you!
Damn, I'm sorry you're having to deal with this. This is one of the biggest reasons why I don't use screen protectors on my phones. I've used a glass one on my Note 5 but didn't like it. Naked display feels the best and performs the best. Not fuss, no glue, no BS. Eeek!
roaduardo said:
Damn, I'm sorry you're having to deal with this. This is one of the biggest reasons why I don't use screen protectors on my phones. I've used a glass one on my Note 5 but didn't like it. Naked display feels the best and performs the best. Not fuss, no glue, no BS. Eeek!
Click to expand...
Click to collapse
Agree with everything. if i had the chance again I would leave it naked, however I would still feel very uncomfortable without protection.. Actual screen exposed to everything is a little risky!
OP, wish I could advise you, but all I can say is take your time and don't rush this task. Since as you aware, you don't want to use a chemical or item that will damage the frame or buttons. Don't use any metal objects.
Feel for you bro, you go ahead with good intentions to protect your device and now in a predicament.
Sent from my SM-N950U using Tapatalk
Limeybastard said:
OP, wish I could advise you, but all I can say is take your time and don't rush this task. Since as you aware, you don't want to use a chemical or item that will damage the frame or buttons. Don't use any metal objects.
Feel for you bro, you go ahead with good intentions to protect your device and now in a predicament.
Sent from my SM-N950U using Tapatalk
Click to expand...
Click to collapse
Thanks for your understanding mate. Indeed tried for the best and ended up worse.
I am not rushing for now, just conctacted Whitestone themselves asking advise on how to fix it, as well as an ebay seller that sells such equipment/tools. He suggested me these:
http://ebay.eu/2g3RySr
http://ebay.eu/2kATYJV
I am not sure about the quality of the Glue Remover and how thin the tools (blades & spudger) are though. Have to make a little research.
That is why also I opened the thread to ask for opinions from people that may have done this or similar task before and to help others in the future.
Warlord1981 said:
Thanks for your understanding mate. Indeed tried for the best and ended up worse.
I am not rushing for now, just conctacted Whitestone themselves asking advise on how to fix it, as well as an ebay seller that sells such equipment/tools. He suggested me these:
http://ebay.eu/2g3RySr
http://ebay.eu/2kATYJV
I am not sure about the quality of the Glue Remover and how thin the tools (blades & spudger) are though. Have to make a little research.
That is why also I opened the thread to ask for opinions from people that may have done this or similar task before and to help others in the future.
Click to expand...
Click to collapse
Before using any chemicals, I would try and use the finest /thinnest plastic card or tool to scrape the glue out of the edges first. Chemicals would be my last resort. Good luck my friend.:good:
roaduardo said:
Damn, I'm sorry you're having to deal with this. This is one of the biggest reasons why I don't use screen protectors on my phones. I've used a glass one on my Note 5 but didn't like it. Naked display feels the best and performs the best. Not fuss, no glue, no BS. Eeek!
Click to expand...
Click to collapse
I have dropped my phones at least 5 times in the last year and each time it landed screen side down. I broke all 5 glass protectors but never the screen. That is why I must have a full adhesive glass protector on. It is a PITA to get perfect but for me, it's worth it.
Mike02z said:
I have dropped my phones at least 5 times in the last year and each time it landed screen side down. I broke all 5 glass protectors but never the screen. That is why I must have a full adhesive glass protector on. It is a PITA to get perfect but for me, it's worth it.
Click to expand...
Click to collapse
I understand, some people need it. I haven't chipped or broken a display since I had an iPhone. Knock wood. Naked is glorious, though.
Plastic tools and alcohol are your friends.
99% Isopropyl should be able to dissolve the glue, and shouldn't leave a mark on the phone (iso evaporates completely and is not dangerous to plastics or metals). A stiff bristled plastic brush would be ideal, maybe an old toothbrush. The thinner and stiffer the bristles, the better.
The iso will dissolve the glue, but you'll need to mechanically agitate it to remove it completely. Bear in mind that traces of iso having touched the glue will streak glass , so a second/third rinse with iso may be necessary.
I'd be careful about getting iso into the switches, as long term iso can degrade rubber (switch seals etc) but as long as you clean, then dry out effectively there shouldn't be an issue (iso will evaporate at room temp in any case). Covering the switches with tape could help, but iso is so thin it will probably go under the tape, and will likely dissolve the glue on the tape too!
e: Whatever you do don't use acetone or any other stronger solvent. Depending on the plastics used acetone will eat right through them, and may affect the finish on other parts too.
Iso really is a decent cleaning solution for most electronic devices.
e ii: Oh, and if you use an old toothbrush, make sure it's very clean. Getting some toothpaste grit on the screen and rubbing it in with a brush would be tragic. Maybe even buy a brand new brush just for this job? Not too expensive for the job, imho.
Limeybastard said:
Before using any chemicals, I would try and use the finest /thinnest plastic card or tool to scrape the glue out of the edges first. Chemicals would be my last resort. Good luck my friend.:good:
Click to expand...
Click to collapse
Yes I'm trying to find such thin tool made of plastic. Cards are too thick for it. It needs to be so thin that can cut you..like razor blades maybe even thinner.
Warlord1981 said:
Yes I'm trying to find such thin tool made of plastic. Cards are too thick for it. It needs to be so thin that can cut you..like razor blades maybe even thinner.
Click to expand...
Click to collapse
Packaging plastic is often thin and stiff... Cut it into a triangle and see if you can get "under" the glue in the gap.
roaduardo said:
I understand, some people need it. I haven't chipped or broken a display since I had an iPhone. Knock wood. Naked is glorious, though.
Click to expand...
Click to collapse
HAHAH, SNAP! Same here, last phone I ever broke was my last iphone I owned , it was the iphone 4s. That was when I was drinking also,
Nekid, is always glorious, without a shadow of a doubt. But I am too shy and need coverage.
iPhone screens can be so brittle. I got used to changing screens for friends at work. During lunch they'd bring me their replacement display kits that they ordered from Ebay and I'd replace their broken screen for some Subway (as payment).
Warlord1981 said:
Yes I'm trying to find such thin tool made of plastic. Cards are too thick for it. It needs to be so thin that can cut you..like razor blades maybe even thinner.
Click to expand...
Click to collapse
Indeed, but not metal.
What i used after installing the whitedome was a sheet of paper, running the corner around gap. Cleaned it easily this way.
princeasi said:
What i used after installing the whitedome was a sheet of paper, running the corner around gap. Cleaned it easily this way.
Click to expand...
Click to collapse
I think OP needs something as thin but stiffer as his glue is cured fully now.
Sent from my SM-N950U using Tapatalk
Limeybastard said:
I think OP needs something as thin but stiffer as his glue is cured fully now.
Click to expand...
Click to collapse
The glue stays soft. If you run the paper around it, it will come up. After about a half a cycle thru, I would cut the edge of the paper each time so that I can continue with a firm edge. I did this after a week of installation.
princeasi said:
The glue stays soft. If you run the paper around it, it will come up. After about a half a cycle thru, I would cut the edge of the paper each time so that I can continue with a firm edge. I did this after a week of installation.
Click to expand...
Click to collapse
Guyz you won't believe it! For the past 2 hours I was doing exactly that! Actually what worked best was a piece of paper that had the dust removal stickers on it (got it from the Olixar Sentinel Case/Screen Protector kit), which is more firm than plain A4 paper. And I was cutting it all the time to keep its sharpness. At some point it finished and I used just plain A4 paper, which wasn't the same but it kinda worked as well..
I was running it inch by inch around the whole frame, taking out glue (indeed soft) little by little! I think it's much better now, though I think I will do another round in the near future.
well after watching videos.. I could see I never needed ALL of that small tube of glue. I always use some kind of screen protector. I like to sell or give away. And you can ALWAYS tell the used phones that never had a screen protector. Always some kind of scratches.. For me selling it mint.. gets more money.
So use some kind of plastic not metal blade to get the excess glue off. It comes off so easily
Warlord1981 said:
First of all which Glue Remover is more suitable? Does it have to be a branded one? Or the unbranded ones will do the job as well? Is there danger that the remover will dry and stay in the gap making it worse? Will it damage the color or consistency of the metal frame? Will it damage the buttons (Power, Volum, Bixby)?
Secondly, which tool should do the job reaching such tiny gap while at the same time not scratching the screen or the metal frame? Metal Blade? Plastic Blade? Wire? Some other tool?
Click to expand...
Click to collapse
I had the same issue with mine and all I used is the film that you remove from the Glass protector before application.. cut off small squares and I ran that in the tiny gaps but making sure you don't go too deep.. Patience and time is must..
I do have a question though.. What is the best thing to use if I wanted to remove my protector off, clean the cured adhesive and use the 2nd bottle to reapply??

Categories

Resources