hi all
sorry for my english,
I have a HTC Diamond Operator ORANGE, I flashed with the official ROM and I sim unlocked it and since it works flawlessly.
except yesterday when I contact a person with such, it was closed at once and since it does not open but now I have to tweak a little open but I do see lines everywhere in green or red and sometimes a few points across, not a permanent screen always different so I thought that my screen is a grill or any time by removing the battery and leaving the CPP 's Opens and I could see the screen HTC Diamond and the home screen of Windows Mobile but after it freezes over.
while searching on your wonderful forum I found a tutorial and I tried handling but no sign of the fact I had access to the BootLoader flash but nothing impossible (i can't flash my htc)
sometimes I see a gray screen sometimes a black screen with dots sometimes vibrates every 30sec, frankly I do not know what to do
in bootloader i see this informations
security unlocked
DIAM100 MFG 64M
SPL-1.40.OLINEX
MicroP-Diam (led) V11
PSOC-DIAM STAGE_PVT v0*30
usb
but i can't terminate the flash, i have error 270 every time, I'm desperate, I do not know what to do he shows no sign of life and I can not access the internal memory to flash memory or access usb with activsync
Once again I am sorry for my English is so bad (because I have not found a solution in the French forum)
Thank you for help.
try flashing hardspl 1.24 see if that will work mate.
Singelton said:
try flashing hardspl 1.24 see if that will work mate.
Click to expand...
Click to collapse
...
go into Bootloader mode (reset and volume down) the connect to your PC via USB and try flashing a ROM (any).
Im about to flash my ROM from original 1.56 to Duttys new, but when i enter bootloader the white loadingscreen gets stuck in my face. Nothing happens and i need to remove the battery to shut down device. Anyone? Freakin frustratin´.
Before I flashed my first rom, I read wiki.xda-developers.com to make sure I understood what I was doing, and used the search button, instead of risking turning my phone into a paper weight.
Since then, Crackwhore has written a very helpful post at the top of this forum about how to use HSPL and USPL to allow you to flash roms.
yeah i know all that. not my first time flashing a phone but the first time it got stuck loading the bootloader. and specially when i´ve only used the HTC update.
darfor said:
Im about to flash my ROM from original 1.56 to Duttys new, but when i enter bootloader the white loadingscreen gets stuck in my face. Nothing happens and i need to remove the battery to shut down device. Anyone? Freakin frustratin´.
Click to expand...
Click to collapse
you mean you couldn't get to boot loader page?
So you already have HSPL 1.56 installed (or have SPL1.54 and used USPL)?
If you have HSPL you could try renaming the .nbh file to blacimg.nbh and copying it to the SD card and entering bootloader
Same problem here. Stuck in bootloader mode. Loading progress indicator never moves beyond 0%. Have always used the card method (blacimg.nbh), but this time it doesn't work and nothing flashes. No matter what I do the system goes to tricolour bootloader screen and says ROM update error. Have tried 3 microSD cards, all in working order, so this isn't the problem. The full problem description is here. Help!
AFW said:
Same problem here. Stuck in bootloader mode. Loading progress indicator never moves beyond 0%. Have always used the card method (blacimg.nbh), but this time it doesn't work and nothing flashes. No matter what I do the system goes to tricolour bootloader screen and says ROM update error. Have tried 3 microSD cards, all in working order, so this isn't the problem. The full problem description is here. Help!
Click to expand...
Click to collapse
try dnloading the rom again amd try.
the file might be corrupt
Have tried that many times. File is not corrupt. I'm getting really worried this is now a brick...
OK, if you can get phone into bootloader, it is not bricked
What does your SPL say in bootloader? Do you get any errors when trying to flash rom? Are you using USPL or HSPL? If USPL, you have to use it before every flash to new rom or radio. If HSPL, are you using correct version?
Was on Dutty's 3.9 XT, but decided to revert to standard WWE 1.56. I flashed the Std 1.56 ROM successfuly, and then tried to restore the ship SPL 1.54 using the card flash method. This failed, and now I'm stuck on the bootlader screen forever.
No matter what I do the THD always goes to bootloader (red-green-blue-white screen), with following text:
BLAC100 32M
SPL-1.54.0000
MicroP-BlackStone (LED) v6
Upgrade ROM code error
Please try again
USB
Click to expand...
Click to collapse
When I start blac_uspl.exe (USPL 2.5), a window flashes (Vista64) for a split second and then nothing else happens. The Vista64 system's USBs work with THD and have been used to sync over past few months.
When I try to run HSPLWrapper_Blackstone_156OliNex.exe and step through the preliminary screens, the Verify that you want to update ROM version screen has the From Image Version as blank and the To Image Version as 1.56.Olinex. When I click to commit the flash the THD screen switches to white with a progress indicator that always stays at 0% until it times out. Recovery does nothing and the same thing always happens. Using Vista64. .Net installed and fine. I can't use the card method (BLACIMG.NBH) - the system also stays on "Loading .... 0%" and nothing else happens.
When I try to flash anything (have tried HSPL1.56, Dutty's 3.9 ROM, stock 1.54 spl) using the card method, the system says "Loading . . ." and hangs there forever without a progress indicator showing.
Your SPL says 1.54.0000. When you try and run USPL.exe have you remembered to disable your antivirus?
Have you tried usb method instead of card for flashing rom?
I know you have said that youi have used usb for syncing, but when in bootloader does it change from 'serial' to 'usb' when you connect HD to PC?
Fallen Spartan - I want to thank you for taking the time to help me resolve this problem. Very much appreciated!
1. Yes, anti-virus disabled and indeed removed from the PC.
2. Yes, have tried the USB method at least 20 times.
3. Yes, the bootloader changes from Serial to USB. It then goes to the progress indicator screen and hangs on 0%. The progress indicator on the RUU on PC also stays at 0% and eventually times out. I've gone through the Recovery routine at least 20 times, with no luck.
When I try to run SSPL-Manual-TouchHD.exe it says "not a valid Win32 application".
I'm a bit perplexed by this.
You have obviously successfully flashed Duttys V3.9 so drivers are fine, you know how to use USPL, both flashing methods (SD card and usb/pc), disabled anti-virus, phone in bootloader.
Have you tried to reflash 1.56 rom or possibly performing a hard reset before trying to use USPL or HSPL. I doubt this would make a difference though.
Have you tried cRaCKwHoRe's USPL GUI v 2.5 Application?
You don't get any code errors?? I'm struggling to find a solution here.
Yes, this is most vexing. I've flashed innumerable times before and never had an issue. I suspect the SPL is fine, but somehow the actual WM ROM image is corrupted. Will now try to load Std 1.56 ROM image again...
Success! The 3rd attempt at reflashing stock 1.56 ROM worked. I don't know why the system bombed out before. Perhaps one of those inexplicable brain farts..
Anyway, all seems to be fine now. Fallen Spartan, you have my endless gratitude for at least responding. Let me know if you need accommodation at next year's FIFA World Cup in South Africa (though I'm a rugby fan).
AFW said:
Success! The 3rd attempt at reflashing stock 1.56 ROM worked. I don't know why the system bombed out before. Perhaps one of those inexplicable brain farts..
Anyway, all seems to be fine now. Fallen Spartan, you have my endless gratitude for at least responding. Let me know if you need accommodation at next year's FIFA World Cup in South Africa.
Click to expand...
Click to collapse
No accomodation required, just glad you got it sorted
Im still stuck. When i installed HSPLWrapper_Blackstone_156OliNex my screen changed colors but would go back to normal when i would turn the screen off and back on so i didnt see it as a problem. I installed the EnergyROM BLACKSTONE 20090608 Standard an tried to go back stock using RUU_BlackStone_HTC_WWE_1.14.405.0_Radio_52.49a.25.26_1.09.25.14_Ship but it gets to 1% then says this update utility cannot be used for you PDA phone. Please check your update utlity.
Then the phone boots up and at the black smart mobility screen in the bottom corner it says
R 1.09.25.14
G 52.49A.25.26U
D 1.14. 21010
the phone boots up with the funny colors again and goes to align screen but it keeps staying there even after i align it.
The bootloader screen says
BLAC100 32M
SPL-1.54.0000
MicroP-BlackStone (LED) v6
USB
Am i tryin to install the wrong stock ROM. I purchased the HD from phonesource-usa if that helps also
can anybody help me at all
Adamsville: perhaps you're stuck in bootloader mode because the WM ROM image flashed on your system has become corrupted or disabled, ie the only thing the system can boot into is the bootloader.
Try flashing a new compatible WM ROM image and see if that works.
AdamsvillE said:
Im still stuck. When i installed HSPLWrapper_Blackstone_156OliNex my screen changed colors but would go back to normal when i would turn the screen off and back on so i didnt see it as a problem. I installed the EnergyROM BLACKSTONE 20090608 Standard an tried to go back stock using RUU_BlackStone_HTC_WWE_1.14.405.0_Radio_52.49a.25.26_1.09.25.14_Ship but it gets to 1% then says this update utility cannot be used for you PDA phone. Please check your update utlity.
Then the phone boots up and at the black smart mobility screen in the bottom corner it says
R 1.09.25.14
G 52.49A.25.26U
D 1.14. 21010
the phone boots up with the funny colors again and goes to align screen but it keeps staying there even after i align it.
The bootloader screen says
BLAC100 32M
SPL-1.54.0000
MicroP-BlackStone (LED) v6
USB
Am i tryin to install the wrong stock ROM. I purchased the HD from phonesource-usa if that helps also
Click to expand...
Click to collapse
a hardreset followed by a 1.54 base rom will solve all ur probs.
or lower spl to 1.14 cos ur stock rom is a 1.14 base as suggested by th name..
cheers
Hey
My first post - weee
I been reading and learning from this forum for quite some time now. And I have flash my rom a few times succesfully.
But I upgrade recently to wm 6.5 with the original rom for HTC.
Its not as good as my 6.1 rom, so i have tried to install a different ROM with wm 6.5.
My problem is that it starts ok - the tricolor screen comes and it says USB in the bottom of the screen. The screen then turns white and a status bar is shown (and on the screen of my pc as well). It says 0 % and stays there for 5 minuts or so. Then it says Error 262 and the I have take out the battery and start med phone again.
When i remove the battery and starts the phone im back to my old wm 6.5 original rom - so no harm done.
Why cant i flash my phone ?
I have tried (after reading a lot) to
- unlock the CID ?
- Hard reset
- Soft reset
- using a different rom
Am I missing something or ?
Try flashing from the card rather than PC. or from PC but take out the sdcard. Also make sure you have Hard-SPL still.
Pezzie said:
Hey
My first post - weee
I been reading and learning from this forum for quite some time now. And I have flash my rom a few times succesfully.
But I upgrade recently to wm 6.5 with the original rom for HTC.
Its not as good as my 6.1 rom, so i have tried to install a different ROM with wm 6.5.
My problem is that it starts ok - the tricolor screen comes and it says USB in the bottom of the screen. The screen then turns white and a status bar is shown (and on the screen of my pc as well). It says 0 % and stays there for 5 minuts or so. Then it says Error 262 and the I have take out the battery and start med phone again.
When i remove the battery and starts the phone im back to my old wm 6.5 original rom - so no harm done.
Why cant i flash my phone ?
I have tried (after reading a lot) to
- unlock the CID ?
- Hard reset
- Soft reset
- using a different rom
Am I missing something or ?
Click to expand...
Click to collapse
take out sd card
do hard reset
do wipe data
go to step 0 and begin with unlocker
flash stock rom
now flash rom you would like.
worst case, if you have trouble flashing it - key--combo to bootloader and flash/hardspl from there
Thx
I unlocked the phone using HARD SPL after removing the SD card and flashed it.
It works
Thx for the help.
Do you have a HardSPL? If not, then you won't be able to flash. You need to do some more reading.
shannonknable said:
Do you have a HardSPL? If not, then you won't be able to flash. You need to do some more reading.
Click to expand...
Click to collapse
YOU need to do some more reading. Specifically one post above... the OP had fixed his issue with HardSPL...
I had that problem a couple of times actually. For me, it was that my port isn't quite as tight as it used to be. (That's what she said) So I just have to make double sure that my phone doesn't move during the flashing sequence AT ALL. Otherwise the same problem will occur.
Hope this helps!
whoops same problem to me. I don't read so good when it's friday night. I stand by my advice though for future problems
Hi.
today i bricked my kaiser when i tried to install a dutty's rom
been trying to get this fixxed for over 5 hours. nothing worked out.
used kaisdiag.nbh from h ttp://forum.xda-developers.com/showthread.php?t=420683
in both suggested solutions my kaiser wont go further then the Loading page. ( waited atleast 10 mins twice without any success)
used some other RUU installs while in the tricolour screen:
ahmedfikry wm6.5 23549 Tilt UC light rom
KAISER_WM65_OS23547_PP12MB_Sonblack05
RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88.07_1.27.12.11_Ship
RUU_Kaiser_HTC_WWE_3.02.405.0_radio_sign_25.70.30.05_1.58.26.20
Ruu_Signed_Duttys_WM6.1_5.2.19700_Hybrid_V2_1_64.08.21_CubeV2_ <== the one wich bricked my phone
Ruu_Signed_Duttys_WM6.1_5.2.19700_Hybrid_V2_1_65.14.06_No_CubeV2_
RUU_Kaiser_TMO_UK_3.31.110.3_radio_sign_25.83.40.02_1.70.18.02_Ship
some other topic sugested to use MTTY.
but that probram says: usb port cannot open.
long story short: im desperate.
can any of u please help me fix my phone ?
its an MDA vario II. model Kais130 P/N 99hcy063-00
thanks in advance.
i'm no expert at recovering bricked phones...
but what i understand is that IF you have a hard SPL (which hard SPL do you have?), then you should be able to recover your device from nearly any situation.
try this...if RUU is not working well, try to flash using the SD card method.
also, try to flash a stock ROM (using RUU as well as using the SD card method). let us know what happens.
Try putting your phone into bootloader, ( press and hold power and camera buttons while doing a soft reset ) once it is in the " tri-color " screen, let us know what it says on the screen.
thanks for your time and the fast response, to both of you.
@#1
i used Pofs hard spl.
and as mentioned above i tried both the RUU way and with my micro SD card.
the SD way only shows me the 'Loading' screen. over and over.
and with the RUU i get several errors. connection errors at 0% and connection errors some later.
some roms just say they wont work on my phone.
and others just reboot my phone.
@#2
i think my phone gets to the bootloader all the time. cause i c no difference when resetting with camera and power button on.
its the tri color screen with the folowing information that shows up:
RUUNBH
Kais130
SPL-1.56.0000
CPLD-8
serial/USB
______________________
the serial shows up when the phone is not connected.. and the USB shows up when its attached to my pc with usb.
Any other suggestions ?
Thanks in advance .
You don't have hard-spl you still have a stock, flash the stock ROM of your carrier from bootloader.
Then follow the noobs guide to flashing.
Thx guys my phone is working like it used to be.
downoaded the original rom from t-mobile again. and again.
now got one wich is working.
thanks for your help.
i was about to throw the brick trough the window.
I recently purchased a used tilt that was hardspl modified and flashed with the stock rom. It worked fine for like a day or so and then when I was just browsing the phone and playing with the games and stuff it turned off on me. I thought the battery was dead so I let it charge for a while and tried to use it. However, whenever I turned it on the AT&T logo screen would show up and it would vibrate but then the phone would turn off before windows mobile booted. I tried soft and hard resets but they did nothing. One time out of the blue the phone worked again for a few minuted but then shut off on me and continued to have the same booting problems. Since then I have tried different batteries made sure the batteries were fully charged and tried flashing some roms via usb sync. I first tried ahmedfikry's rom but that did nothing so I moved onto flashing the stock rom (yes I realize now I should have flashed the stock rom first). This also did nothing, so I have been flashing various radios that are suppose to work with the phone. Nothing seems to help. The phone can get to the tricolor screen when I do the hold camera+power button thing and this is what it says:
Security Unlocked
KAIS1*0 MFG
SPL-1.0. OliPof
CPLD-8
Even though the phone shows up as mobile sync in my PC tray when I have it at the tricolor screen, I cannot access the device at all. Is that normal? Furthermore even though I have flashed roms successfully (or at least it says it was successful) whenever I go to flash the rom again the CustomRUU program shows previous rom as being blank. What else can I do? I am at my wits end and as a newb it is very hard to find information since the wiki is down.
try reflashing it. If it shows up in activesync I don't think that it is dead, but I could be wrong.
MeteoricManiac said:
I recently purchased a used tilt that was hardspl modified and flashed with the stock rom. It worked fine for like a day or so and then when I was just browsing the phone and playing with the games and stuff it turned off on me. I thought the battery was dead so I let it charge for a while and tried to use it. However, whenever I turned it on the AT&T logo screen would show up and it would vibrate but then the phone would turn off before windows mobile booted. I tried soft and hard resets but they did nothing. One time out of the blue the phone worked again for a few minuted but then shut off on me and continued to have the same booting problems. Since then I have tried different batteries made sure the batteries were fully charged and tried flashing some roms via usb sync. I first tried ahmedfikry's rom but that did nothing so I moved onto flashing the stock rom (yes I realize now I should have flashed the stock rom first). This also did nothing, so I have been flashing various radios that are suppose to work with the phone. Nothing seems to help. The phone can get to the tricolor screen when I do the hold camera+power button thing and this is what it says:
Security Unlocked
KAIS1*0 MFG
SPL-1.0. OliPof
CPLD-8
Even though the phone shows up as mobile sync in my PC tray when I have it at the tricolor screen, I cannot access the device at all. Is that normal? Furthermore even though I have flashed roms successfully (or at least it says it was successful) whenever I go to flash the rom again the CustomRUU program shows previous rom as being blank. What else can I do? I am at my wits end and as a newb it is very hard to find information since the wiki is down.
Click to expand...
Click to collapse
Upgrade your SPL! Newest SPL is 3.56, I recommend 3.xx (xx - whatever you want), because they work perfectly with WM 6.1 and WM 6.5. Older SPLs might cause you some problems...