Database Develop

[SOLVED] Noob needs help! Is my qtek9100 a brick?

Hi!
this is my first post here, so sorry for my bad english or mistakes
i bought a qtek 9100 on ebay, and i'm wondering if it's a brick or not. i received the device 3 days ago. during this time i read through a LOT of threads here, tried a few things and nothing works.
here is some info:
- the phone is a qtek 9100 without branding
- the IPL is now 1.01 (i flashed "CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE" successfully)
- the SPL is 2.18 (because of the missing suffix ".0001" i guess it's a G3)
- GSM is 01.12.10
- OS is 1.5.4.2
- when i start the device (without any button pressed) it stops at the splash screen (which was a qtek logo before flashing, and is now this picture with a beer, that says "some things last forever" )
- i can get into bootloader screen (color screen) by holding camera button while starting
- in bootloader screen a small "USB" appears when i connect cable to usb on pc
- when i press communicate and voice buttons (on the sides) while starting, the "Press send to restore factory default" screen appears, but pressing send prints out "Format FAT Partition Format is Failed"
- the device gets recognized by windows ("Mobile Device" appears on my computer)
- ActiveSync 4.5 does not connect to device, not even as guest.
- when i hit "Connect..." in ActiveSync's connection settings, nothing is found
("Allow USB Connections" is ON)
- the device is CID-locked ("FF" state in Mtty 1.42)
- i can't unlock CID, because i can't get "EnableRapi.cab" onto the device without ActiveSync connection
Ok, these are basically the things i know now. The problem is that i never saw any other screen then the "HTC" boot screen, the "Qtek" splash logo (the one with the clouds) before i flashed with custom ruu wwe, after that i see the new splash logo, and i can get into bootloader (color) screen. I never saw any windows mobile running on this device! I could never establish a connection with ActiveSync!
So i hope that someone here on this nice forum can help me get this device to work (WM5 would even be enough right now) or at least give me a hint!
Thanks in advance!

Put the phone in bootloader mode and flash back to the original ROM.

since i bought it in ebay i don't have the original rom of this device.
but i found "233309-qtek9100_2180707_21807109_20710_qtek_ger_ship.exe" through google, which seems to be an original qtek rom (version 2.18). shall i flash this one?

You can find in the Wiki the latest official roms of every brand for our Wizards .-

ok, thanks.
i found one (Qtek GER 2.18.7) and flashed it. the process was successfull, now the IPL/SPL is both 2.18 . But the device still doesn't start and stops at the splash screen (which is now the original qtek splash again). I can still get into bootloader mode and hard reset results in "Format is failed"! No ActiveSync connection either... how should i proceed now?

i basically narrowed it down to these two problems:
- the splash screen freezes
- hard reset error "Format is failed"
( IPL: 2.18, SPL: 2.18 )
can't anybody help please?
i'm freaking out about this

With everything i’ve read the only people who’ve had any success had CID unlocked devices.

ok, i think that too for what i've read so far...
is there any other way of CID unlocking except lokiwiz (can't copy enablerapi.cab without activesync!)?
would this imei-check service that i've read about work in this case?
meanwhile i've also tried something with mtty (r2sd all) but doesn't work -> "didn't get proper security level"
is this also because of the CID lock? i tried to find out the right password to enter in mtty, but found nothing that worked...
does anybody know the correct password?

I couldent CID unluck my 9100 with lokiwiz so i did it 5min ago with Wizard Service Tool (ha to reboot my computer).

I'm having the exact same problem,
except I can't flash any other ROMS so I'm stuck looking at this incredibly frustrating beer picture, with "some things last forever".
Does anyone have any further ideas?

Look up the orignal rom on the wiki, get into bootloader. And flash it back.
Jodda said:
I'm having the exact same problem,
except I can't flash any other ROMS so I'm stuck looking at this incredibly frustrating beer picture, with "some things last forever".
Does anyone have any further ideas?
Click to expand...
Click to collapse

Jodda said:
I'm having the exact same problem,
except I can't flash any other ROMS so I'm stuck looking at this incredibly frustrating beer picture, with "some things last forever".
Does anyone have any further ideas?
Click to expand...
Click to collapse
Hi Friend!
I have the same problem with my Qtek9100!
Any ideas? have you solved your problem?
I have the frustrating beer picture
Please help me.
Very Thanks

Like I sad before
Get into bootloader, flash back the original rom and try again.
mizobuchi said:
Hi Friend!
I have the same problem with my Qtek9100!
Any ideas? have you solved your problem?
I have the frustrating beer picture
Please help me.
Very Thanks
Click to expand...
Click to collapse

I put the original rom.
But... the problem is the same.
when I started the device (without any button pressed) it stops at the splash screen (which has a qtek logo before flashing)
- i can get into bootloader screen (color screen) by holding camera button while starting, I installed the original and others rom who days before works perfectly... Now... this stopped at splash screen
- when I tryed to format.. = "Format FAT Partition Format is Failed"
Any idea?
I have tried this : http://forum.gsmhosting.com/vbb/showthread.php?t=332143
but... without success.
Could you help me, please?
Very Thanks

i'm still stuck with the same problem with hang up on qtek splash screen, too!
i have IPL 2.18 and SPL 2.18 and i can get in boot loader screen and connect with usb. (but no activesync connection!)
formatting doesn't work either.
does anybody have an idea how to solve this?? it's frustrating... i've tried almost every guide here on the forums.

same proplem here with
ipl 2.16
and spl 2.16

I used this to fix this problem
Hi i had the same problem the other week, installed a dodgy app, went to do a hard reset and wouldn't do a hard reset format failed. Tried updating rom everything worked ok until you booted it up. Wouldn't go past second splash sreen. After a few hours of trawling round i found this thread.
http://forum.xda-developers.com/showthread.php?t=276963&highlight=format+is+failed
worked for me. Hope this helps you out.

Problem in connecting to my PC
Hey ,
I just bought a qtek 9100 a day before ... I tried to connect it with my computer.. instead of connecting my battery gets charging well can u plz help me out !
is there any software that i should install in my pc in order to get it connected to my PC...... please help me fast ! Lot of work is pending !
Thanks
Salman

Ok guys, I finally have this SOLVED.
My QTEK 9100 is working fine now!!!
I'm so happy with it right now
Since nothing I tried worked, I went to imei-check.co.uk and got my phone completly unlocked! It only cost me about 11€ and since it works now I have to admit that it was worth it (no advertising). After the unlocking was done I could do the "r2sd all"-method (Tool: MTTY 1.42) using a miniSD card. You can find a good tutorial on this board somewhere. After that everything was just fine...
-> I never saw it working and Hell Yeah: This baby just kicks a$$ !!! (although it's kinda 'oldschool' these days )

Stuck in bootloader loading screen.

Im about to flash my ROM from original 1.56 to Duttys new, but when i enter bootloader the white loadingscreen gets stuck in my face. Nothing happens and i need to remove the battery to shut down device. Anyone? Freakin frustratin´.

Before I flashed my first rom, I read wiki.xda-developers.com to make sure I understood what I was doing, and used the search button, instead of risking turning my phone into a paper weight.
Since then, Crackwhore has written a very helpful post at the top of this forum about how to use HSPL and USPL to allow you to flash roms.

yeah i know all that. not my first time flashing a phone but the first time it got stuck loading the bootloader. and specially when i´ve only used the HTC update.

darfor said:
Im about to flash my ROM from original 1.56 to Duttys new, but when i enter bootloader the white loadingscreen gets stuck in my face. Nothing happens and i need to remove the battery to shut down device. Anyone? Freakin frustratin´.
Click to expand...
Click to collapse
you mean you couldn't get to boot loader page?

So you already have HSPL 1.56 installed (or have SPL1.54 and used USPL)?
If you have HSPL you could try renaming the .nbh file to blacimg.nbh and copying it to the SD card and entering bootloader

Same problem here. Stuck in bootloader mode. Loading progress indicator never moves beyond 0%. Have always used the card method (blacimg.nbh), but this time it doesn't work and nothing flashes. No matter what I do the system goes to tricolour bootloader screen and says ROM update error. Have tried 3 microSD cards, all in working order, so this isn't the problem. The full problem description is here. Help!

AFW said:
Same problem here. Stuck in bootloader mode. Loading progress indicator never moves beyond 0%. Have always used the card method (blacimg.nbh), but this time it doesn't work and nothing flashes. No matter what I do the system goes to tricolour bootloader screen and says ROM update error. Have tried 3 microSD cards, all in working order, so this isn't the problem. The full problem description is here. Help!
Click to expand...
Click to collapse
try dnloading the rom again amd try.
the file might be corrupt

Have tried that many times. File is not corrupt. I'm getting really worried this is now a brick...

OK, if you can get phone into bootloader, it is not bricked
What does your SPL say in bootloader? Do you get any errors when trying to flash rom? Are you using USPL or HSPL? If USPL, you have to use it before every flash to new rom or radio. If HSPL, are you using correct version?

Was on Dutty's 3.9 XT, but decided to revert to standard WWE 1.56. I flashed the Std 1.56 ROM successfuly, and then tried to restore the ship SPL 1.54 using the card flash method. This failed, and now I'm stuck on the bootlader screen forever.
No matter what I do the THD always goes to bootloader (red-green-blue-white screen), with following text:
BLAC100 32M
SPL-1.54.0000
MicroP-BlackStone (LED) v6
Upgrade ROM code error
Please try again
USB
Click to expand...
Click to collapse
When I start blac_uspl.exe (USPL 2.5), a window flashes (Vista64) for a split second and then nothing else happens. The Vista64 system's USBs work with THD and have been used to sync over past few months.
When I try to run HSPLWrapper_Blackstone_156OliNex.exe and step through the preliminary screens, the Verify that you want to update ROM version screen has the From Image Version as blank and the To Image Version as 1.56.Olinex. When I click to commit the flash the THD screen switches to white with a progress indicator that always stays at 0% until it times out. Recovery does nothing and the same thing always happens. Using Vista64. .Net installed and fine. I can't use the card method (BLACIMG.NBH) - the system also stays on "Loading .... 0%" and nothing else happens.
When I try to flash anything (have tried HSPL1.56, Dutty's 3.9 ROM, stock 1.54 spl) using the card method, the system says "Loading . . ." and hangs there forever without a progress indicator showing.

Your SPL says 1.54.0000. When you try and run USPL.exe have you remembered to disable your antivirus?
Have you tried usb method instead of card for flashing rom?
I know you have said that youi have used usb for syncing, but when in bootloader does it change from 'serial' to 'usb' when you connect HD to PC?

Fallen Spartan - I want to thank you for taking the time to help me resolve this problem. Very much appreciated!
1. Yes, anti-virus disabled and indeed removed from the PC.
2. Yes, have tried the USB method at least 20 times.
3. Yes, the bootloader changes from Serial to USB. It then goes to the progress indicator screen and hangs on 0%. The progress indicator on the RUU on PC also stays at 0% and eventually times out. I've gone through the Recovery routine at least 20 times, with no luck.
When I try to run SSPL-Manual-TouchHD.exe it says "not a valid Win32 application".

I'm a bit perplexed by this.
You have obviously successfully flashed Duttys V3.9 so drivers are fine, you know how to use USPL, both flashing methods (SD card and usb/pc), disabled anti-virus, phone in bootloader.
Have you tried to reflash 1.56 rom or possibly performing a hard reset before trying to use USPL or HSPL. I doubt this would make a difference though.
Have you tried cRaCKwHoRe's USPL GUI v 2.5 Application?
You don't get any code errors?? I'm struggling to find a solution here.

Yes, this is most vexing. I've flashed innumerable times before and never had an issue. I suspect the SPL is fine, but somehow the actual WM ROM image is corrupted. Will now try to load Std 1.56 ROM image again...

Success! The 3rd attempt at reflashing stock 1.56 ROM worked. I don't know why the system bombed out before. Perhaps one of those inexplicable brain farts..
Anyway, all seems to be fine now. Fallen Spartan, you have my endless gratitude for at least responding. Let me know if you need accommodation at next year's FIFA World Cup in South Africa (though I'm a rugby fan).

AFW said:
Success! The 3rd attempt at reflashing stock 1.56 ROM worked. I don't know why the system bombed out before. Perhaps one of those inexplicable brain farts..
Anyway, all seems to be fine now. Fallen Spartan, you have my endless gratitude for at least responding. Let me know if you need accommodation at next year's FIFA World Cup in South Africa.
Click to expand...
Click to collapse
No accomodation required, just glad you got it sorted

Im still stuck. When i installed HSPLWrapper_Blackstone_156OliNex my screen changed colors but would go back to normal when i would turn the screen off and back on so i didnt see it as a problem. I installed the EnergyROM BLACKSTONE 20090608 Standard an tried to go back stock using RUU_BlackStone_HTC_WWE_1.14.405.0_Radio_52.49a.25.26_1.09.25.14_Ship but it gets to 1% then says this update utility cannot be used for you PDA phone. Please check your update utlity.
Then the phone boots up and at the black smart mobility screen in the bottom corner it says
R 1.09.25.14
G 52.49A.25.26U
D 1.14. 21010
the phone boots up with the funny colors again and goes to align screen but it keeps staying there even after i align it.
The bootloader screen says
BLAC100 32M
SPL-1.54.0000
MicroP-BlackStone (LED) v6
USB
Am i tryin to install the wrong stock ROM. I purchased the HD from phonesource-usa if that helps also

can anybody help me at all

Adamsville: perhaps you're stuck in bootloader mode because the WM ROM image flashed on your system has become corrupted or disabled, ie the only thing the system can boot into is the bootloader.
Try flashing a new compatible WM ROM image and see if that works.

AdamsvillE said:
Im still stuck. When i installed HSPLWrapper_Blackstone_156OliNex my screen changed colors but would go back to normal when i would turn the screen off and back on so i didnt see it as a problem. I installed the EnergyROM BLACKSTONE 20090608 Standard an tried to go back stock using RUU_BlackStone_HTC_WWE_1.14.405.0_Radio_52.49a.25.26_1.09.25.14_Ship but it gets to 1% then says this update utility cannot be used for you PDA phone. Please check your update utlity.
Then the phone boots up and at the black smart mobility screen in the bottom corner it says
R 1.09.25.14
G 52.49A.25.26U
D 1.14. 21010
the phone boots up with the funny colors again and goes to align screen but it keeps staying there even after i align it.
The bootloader screen says
BLAC100 32M
SPL-1.54.0000
MicroP-BlackStone (LED) v6
USB
Am i tryin to install the wrong stock ROM. I purchased the HD from phonesource-usa if that helps also
Click to expand...
Click to collapse
a hardreset followed by a 1.54 base rom will solve all ur probs.
or lower spl to 1.14 cos ur stock rom is a 1.14 base as suggested by th name..
cheers

Kaiser bricked nothing worked yet.

Hi.
today i bricked my kaiser when i tried to install a dutty's rom
been trying to get this fixxed for over 5 hours. nothing worked out.
used kaisdiag.nbh from h ttp://forum.xda-developers.com/showthread.php?t=420683
in both suggested solutions my kaiser wont go further then the Loading page. ( waited atleast 10 mins twice without any success)
used some other RUU installs while in the tricolour screen:
ahmedfikry wm6.5 23549 Tilt UC light rom
KAISER_WM65_OS23547_PP12MB_Sonblack05
RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88.07_1.27.12.11_Ship
RUU_Kaiser_HTC_WWE_3.02.405.0_radio_sign_25.70.30.05_1.58.26.20
Ruu_Signed_Duttys_WM6.1_5.2.19700_Hybrid_V2_1_64.08.21_CubeV2_ <== the one wich bricked my phone
Ruu_Signed_Duttys_WM6.1_5.2.19700_Hybrid_V2_1_65.14.06_No_CubeV2_
RUU_Kaiser_TMO_UK_3.31.110.3_radio_sign_25.83.40.02_1.70.18.02_Ship
some other topic sugested to use MTTY.
but that probram says: usb port cannot open.
long story short: im desperate.
can any of u please help me fix my phone ?
its an MDA vario II. model Kais130 P/N 99hcy063-00
thanks in advance.

i'm no expert at recovering bricked phones...
but what i understand is that IF you have a hard SPL (which hard SPL do you have?), then you should be able to recover your device from nearly any situation.
try this...if RUU is not working well, try to flash using the SD card method.
also, try to flash a stock ROM (using RUU as well as using the SD card method). let us know what happens.

Try putting your phone into bootloader, ( press and hold power and camera buttons while doing a soft reset ) once it is in the " tri-color " screen, let us know what it says on the screen.

thanks for your time and the fast response, to both of you.
@#1
i used Pofs hard spl.
and as mentioned above i tried both the RUU way and with my micro SD card.
the SD way only shows me the 'Loading' screen. over and over.
and with the RUU i get several errors. connection errors at 0% and connection errors some later.
some roms just say they wont work on my phone.
and others just reboot my phone.
@#2
i think my phone gets to the bootloader all the time. cause i c no difference when resetting with camera and power button on.
its the tri color screen with the folowing information that shows up:
RUUNBH
Kais130
SPL-1.56.0000
CPLD-8
serial/USB
______________________
the serial shows up when the phone is not connected.. and the USB shows up when its attached to my pc with usb.
Any other suggestions ?
Thanks in advance .

You don't have hard-spl you still have a stock, flash the stock ROM of your carrier from bootloader.
Then follow the noobs guide to flashing.

Thx guys my phone is working like it used to be.
downoaded the original rom from t-mobile again. and again.
now got one wich is working.
thanks for your help.
i was about to throw the brick trough the window.

Diamond won't turn on!

I HAVE A HTC TOUCH DIAMOND. WHEN I TURN IT ON IT DOES NOT START UP IN PHONE MODE. THE SCREEN COMES UP WITH A RED,GREEN,BLUE AND WHITE BANDED SCREEN(BOOT-LOADER) WITH
DIAM130 64M
SPL-1.38.0000
MICROP-DIAM (LED) V11
IN THE RED SECTION
PSOC-DIAM STAGE_PVT V0X32
AND SERIAL IN THE WHITE SECTION.
when i connect to computer its shows usb i have done hard reset and installed new ROM from HTC website din't work for me i also have tried Hard-SPL olinex version but they stop on 0% dn't allow me to upload to the phone for some reason
I HAVE PRESSED THE RESET BUTTON AND REMOVED THE BATTERY. STILL NOTHING WORKS. NOT TOUCH SCREEN OR BUTTONS. IT WONT EVEN TURN OFF from boot loader WITH OUT REMOVING THE BATTERY...
CAN ANYONE TELL ME WHAT to do step by step
PLEASE SOME ONE HELP ME!!!!

You could start with reading the stickies:
http://forum.xda-developers.com/forumdisplay.php?f=430
In particular, this may help you to find the root cause of your problem:
http://forum.xda-developers.com/showthread.php?t=409425
Good luck!

[Q] help!!!htc touch diamond 2(topaz)!!

hello!i have an htc touch diamond 2 and i used hard-SPL in order to put a new rom to my device.i did it successfully(at least pc said so) and then i installed a rom energy topaz successfully too.but when it was done my device restarted on its own and it cant boot.the only thing that it does is to appear the htc green logo in white screen and then restarting again and again and again!!i kept the volume down button and it booted on the red-green-blue-white screen and it says this:
TOPA100 32Μ
SPL-2.51.oliNex ------>on the red part
MicroP-Topaz (led) V10
TURBO HW/TURBO SW
TPMFG DATA
517,557 190,896
186,212 854,214 --------->this one one green part
847,894 calibrated
and on the white part it says usb when its connected with pc and serial when its not!!what can i do now?i tried also some other roms for topaz which were succefully loaded too but the same thing happens again and again.i would apriaciate some help.
thanx.

billyprepo said:
hello!i have an htc touch diamond 2 and i used hard-SPL in order to put a new rom to my device.i did it successfully(at least pc said so) and then i installed a rom energy topaz successfully too.but when it was done my device restarted on its own and it cant boot.the only thing that it does is to appear the htc green logo in white screen and then restarting again and again and again!!i kept the volume down button and it booted on the red-green-blue-white screen and it says this:
TOPA100 32Μ
SPL-2.51.oliNex ------>on the red part
MicroP-Topaz (led) V10
TURBO HW/TURBO SW
TPMFG DATA
517,557 190,896
186,212 854,214 --------->this one one green part
847,894 calibrated
and on the white part it says usb when its connected with pc and serial when its not!!what can i do now?i tried also some other roms for topaz which were succefully loaded too but the same thing happens again and again.i would apriaciate some help.
thanx.
Click to expand...
Click to collapse
Sorry i didn't get back to you sooner and you added the perfect amount of info
ok where to start - firstly have you tried a hard reset after flashing the ROM this isn't always needed but may possibly free something up to make the energy ROM work. You could also try flashing back to a stock ROM from the HTC website and then re-flash the one you want after everything is ok on the stock ROM.
when you say successfully loaded do you mean the screen shows 100% (phone not computer) or does it say complete as it can say 100% on the screen for a little while and not work ? I don't do mine by the PC i use a memory card to flash it and mine always comes up complete when done and then press a key to restart the phone.
failing all of this head back into the hard_spl thread run the spl_relocker in the first post and once relocked flash with hard_spl 1.83 no idea if the newer version is less or more buggy but i use 1.83 and it's smooth sailing.
You could also try flashing from a memory card instead if you have one to hand

thanx warlordxxx!its done!

billyprepo said:
thanx warlordxxx!its done!
Click to expand...
Click to collapse
No problemo