Related
okay so when my n1 is in sleep, it takes like 3 tries to wake it up. The first time I press the unlock button the unlock screen comes and then goes back to sleep instantly. The second time the lights for the back menu home and search light up and that's it. the third time it works. I'm on froyo. anyone else with this problem?
I have a similar issue.
Sometimes just the capacitive buttons light up and not the screen. I have to make 2 or 3 tries to get it to turn on. Its rare, but its there. It only happened on 2.2.
ok good, me too!
was just looking for this topic.
mine doesnt always turn anything on at all. sometimes the light go on, others nothing. Also trying to turn off the phone is hard as it sleeps straight away with out opening up the power menu.
I have a stock N1, which recently updated to Froyo, with the same problem.
any ideas would be great!
cheers,
lorin.bute said:
I have a similar issue.
Sometimes just the capacitive buttons light up and not the screen. I have to make 2 or 3 tries to get it to turn on. Its rare, but its there. It only happened on 2.2.
Click to expand...
Click to collapse
Also happens on CM 5.0.7.1.
i think it may be a hardware button issue.
I have tried turning mine off (had to pull the battery out) and then to turn it on.
It should turn on readily as it has nothing to do with the OS at that point.
any ideas?
No HW button issue described. HW button works - if it didn't, lights wouldn't go on. It's a wrong reaction on the button, at least that's what OP describes (and me too).
Your N1's power button is dying, it's a known HARDWARE issue. I experienced all of that what you may think a software bug, nut dear friends, prepare to meet HTC or Google for warranty. My N1's power button is dead, I couldn't swap for a new one because I bought it in my country where no official distributor for N1 yet. Sad!
ps: you may try to search for "N1 power button" and see there are more and more reports about this problem.
I've read more than one or two threads on power button issues, and I know what I'm talking about. My power button DOES power up the phone when the battery is taken off the first shot, it DOES wake the phone from standby, it DOES register long presses - there was even one time when a second press was long, and suddenly the screen woke up with power menu, while the first press left it dark with touch button light going on.
Doesn't look even a bit like HW to me. HW would leave the phone dead, non-responsive to touches, or create a loose touch which would translate into several touches - none of those would EVER turn into a phone being on with screen off, and suddenly snapping back to screen on when the SCREEN is touched several times.
Could be your cpu was too busy to accept any inputs.
I have a thread about it here:
http://forum.xda-developers.com/showthread.php?t=692874
Take your time! As for me, I'm using my N1 for 3 months now for the power button to completely dead with everyday use (I didn't use any app to trackball-wake).
As I said, all the things you are yelling I have been through. And I, too, thought it was software problem.
I tried both MCR and Cya with no hope.
Good luck!
ps: One of my friend just told me about his N1's power button issue right after hearing me telling about mine.
This sucks
anyone know where i can buy a new button??
Corrupt SD Card
I had the same issue. I'd press the power button, the bottom four buttons would light up but no screen wake. Only way to get out of it was to pull the battery. It would happen maybe 30-40% of the time. (Nexus One Froyo FRF72)
I think it was due to a corrupt MicroSD card. I recently installed a 32gb card and put some music on it using songbird and possibly didn't safely remove. That's when I started getting issues. Removed the SD card completely and it worked fine. Changed back to the old card and no issues. Then formatted the 32gb and tried again, worked fine. Then I tried to transfer more music, there was an error and I got the same problem. (Cheap ebay card from Hong Kong, that'll teach me).
Anyway, I'd be interested to know if that solved anyone else's problem, because all I see on forums are that it's a faulty power button, but that didn't seem to be the case in my situation.
Cheers,
Dylan
-Witty esoteric statement about science/technology.
Mine is doing kinda the same weird thing but a little different.
When I push the power button the screen comes on but is unresponsive to touch. If I press the power button again the screen dims and then turns off, the home keys light up and then the trackball glows white. The phone then does not respond to the power button for around 10 secs and repeats this behavior 4 or 5 times until it actually starts working correctly and I can swipe my finger to get to the home screen.
It usually does this after being inactive for a period of time, like after sitting overnight.
FRF91
LancherPro Beta 0.6.7.2(maybe the problem?)
jimbobalu said:
Mine is doing kinda the same weird thing but a little different.
When I push the power button the screen comes on but is unresponsive to touch. If I press the power button again the screen dims and then turns off, the home keys light up and then the trackball glows white. The phone then does not respond to the power button for around 10 secs and repeats this behavior 4 or 5 times until it actually starts working correctly and I can swipe my finger to get to the home screen.
It usually does this after being inactive for a period of time, like after sitting overnight.
FRF91
LancherPro Beta 0.6.7.2(maybe the problem?)
Click to expand...
Click to collapse
i have almost the same issue, although mine happened twice when i was on EPE54B but it's been far more common on FRF91
the only difference is my power will continue to turn the back light on and off no matter if the screen has already timed out or not
kobecamp2009 said:
okay so when my n1 is in sleep, it takes like 3 tries to wake it up. The first time I press the unlock button the unlock screen comes and then goes back to sleep instantly. The second time the lights for the back menu home and search light up and that's it. the third time it works. I'm on froyo. anyone else with this problem?
Click to expand...
Click to collapse
I have exactly the same issue. Over in the general forum, there's another thread on this issue. Many, myself included, are reporting that this problem started after the FRF91 update. Can you confirm?
rtx101 said:
Your N1's power button is dying, it's a known HARDWARE issue. I experienced all of that what you may think a software bug, nut dear friends, prepare to meet HTC or Google for warranty. My N1's power button is dead, I couldn't swap for a new one because I bought it in my country where no official distributor for N1 yet. Sad!
ps: you may try to search for "N1 power button" and see there are more and more reports about this problem.
Click to expand...
Click to collapse
Read again carefully. Are you sure your hardware problem was identical to what the OP described? I've noticed a lot of people with obvious hardware problems (i.e., the power button is completely unresponsive) posting on threads like this when they actually have a different problem. It's very confusing.
britoso said:
Could be your cpu was too busy to accept any inputs.
I have a thread about it here:
http://forum.xda-developers.com/showthread.php?t=692874
Click to expand...
Click to collapse
This sounds VERY promising -- thank you britoso!
PS: Are you guys getting the unresponsive unlock slider like britoso describes?
I had this problem when I first flashed CM6 yesterday. Even after wiping and reflashing it was the same. Only way to get out of the black screen was to do a soft reset, power + vol down + trackball. I finally found out that my SD card malfunctioned and was corrupt. I tried reformatting the sd card in an microsd card reader but windows said it could not be reformatted. I finally switched back to another microsd card that was working, wipe and reflashed cm6 and the problem went away. Try backing up all the data on your microsd onto your computer then reformat it and wipe then reflash to see if it works
Edit: ughhhh it just happened again, but not as bad as before, turns back on after second try... maybe i didnt press the trackball hard enough
I can not seem to get my NC to power off completly. I have tried holding the power button for 15 seconds and I have tried holding the power button then hitting the power off completly soft button that appear's.
The screen turns off ... but when I go back later to turn on my NC it was only in sleep mode.
Any thoughts ?
Holding just the power button and the home button until it powers down works for me to fully power down. Sometimes I need to hold both again to turn back on.
Could it be that the Nook is powering on by itself after a power down? I've run into this a couple times so far. As well, for the longest time my 2.1 Milestone had this problem. I would do a full power down, and some time after the phone would boot up by itself. This was later addressed in a small update to the 2.1 that I'm running on the phone.
Incriminified said:
Could it be that the Nook is powering on by itself after a power down? I've run into this a couple times so far. As well, for the longest time my 2.1 Milestone had this problem. I would do a full power down, and some time after the phone would boot up by itself. This was later addressed in a small update to the 2.1 that I'm running on the phone.
Click to expand...
Click to collapse
Mmmmm well this situation would suck. Not sure how to fix this then. It does seem like it is powering down and rebooting itself a bit later .. ?
I only have to hold the power button for two or three seconds, then the power off dialog box appears.
my power button is no longer working. I try a lot of apps: nolock, lock 2.0, power off, lock screen widget, anylock .... but almost is turn off display, can't wake up with volume button.
please help me how to do it ? Thanks.
jackma123 said:
my power button is no longer working. I try a lot of apps: nolock, lock 2.0, power off, lock screen widget, anylock .... but almost is turn off display, can't wake up with volume button.
please help me how to do it ? Thanks.
Click to expand...
Click to collapse
I don't know what ROM you're running, but MIUI has the option to do what you're asking. It's in the settings menu (I believe under Lockscreen).
oh, ROM CM7 have it also, but I want separate app. Do you know any apps ?
Widget locker. Like 3 bucks in market enable easy wake
Sent from my Samsung Galaxy S Captivate with ICS and a broken power button.
i just ran into the same problem. golocker is working great for me. and its free in the market.
Also MiLocker.
Fix Broken Power Button by Destil
I found this..
market.android.com/details?id=cz.destil.fixbrokenpb&hl=en
When I tried to download it said it wasn't compatible with captivate but I found the .apk and it ended up working. I attached the .apk I was using to this post.
Another thought, I took my phone apart and cleaned it. I took everything apart down to the motherboard and I poured a little rubbing alcohol on the actual button and pressed it a bunch of times (no battery in of course) and after it dried out it seemed to help get it working again.
Also, when I started having problems again I installed a different kernel and that seemed to help as well. Who knows.. but it has been working ever since.
The Fix Broken Power Button by Destil .apk is below
Thank you topiratiko, I was about to go crazy worrying about not being unable to turn my screen on. But what will I do if the phone shuts off? How will I turn it on? My power button seems to be unable to work.
kbolt said:
Thank you topiratiko, I was about to go crazy worrying about not being unable to turn my screen on. But what will I do if the phone shuts off? How will I turn it on? My power button seems to be unable to work.
Click to expand...
Click to collapse
You can allways go into download mode and flash a kernel for ex and check reboot so it'll boot up, or even better use a jig by inserting it for just a bit to power on and to avoid download mode.
No problems with my Serendipity 7 ROM aside from a few occasional crashes/freezes, on my i897... but then last night, out of no where, my screen wasn't coming on. I thought it had froze again, so I did the Vol up/down+power reboot.
Came back up, then when I tried to turn the screen on again, it wasn't working. I put the cable in for power/USB, and the screen came up no problem. I thought maybe the power button wasn't working, but it reboots with all three buttons down... not sure why. Then I tested just holding the two Vol buttons and no power, but it still rebooted...
Looks like the power button is acting stuck down even though I can clearly hear the button working. Ideas?
Mobile tech videos has a fairly affordable power button replacement service.
sent mine you him, got it back in perfectly working order within a week.
I have a Galaxy S i896 (Rogers captivate model), been running CM9 on it for quite some time now and I never had a problem with it.
Until recently, my lock button stopped working. Thankfully, CM9 allows me to use the volume buttons to turn on the screen, and I can lock the device from the notification bar. However, I sometimes get that screen that pops up when you long press the power button (airplane mode, screen shot, reboot etc...) but I don't know how. Also, whenever I remove and re-insert my battery, the phone turns on by itself! So it would seem that the button is stuck somehow, and once the phone is turned on, it is being ignored.
I read somewhere that this is sometimes caused by rooting the phone, however I wasn't completely sure about how true this information was, and therefore my question is: does anybody know what causes this, and how can I fix it!
Thanks!
mmmboulos said:
I have a Galaxy S i896 (Rogers captivate model), been running CM9 on it for quite some time now and I never had a problem with it.
Until recently, my lock button stopped working. Thankfully, CM9 allows me to use the volume buttons to turn on the screen, and I can lock the device from the notification bar. However, I sometimes get that screen that pops up when you long press the power button (airplane mode, screen shot, reboot etc...) but I don't know how. Also, whenever I remove and re-insert my battery, the phone turns on by itself! So it would seem that the button is stuck somehow, and once the phone is turned on, it is being ignored.
I read somewhere that this is sometimes caused by rooting the phone, however I wasn't completely sure about how true this information was, and therefore my question is: does anybody know what causes this, and how can I fix it!
Thanks!
Click to expand...
Click to collapse
I also have this problem with a stock ROM. The power button doesn't work and i cant even flash another ROM in recovery because of that. It only turns on when putting the charger on or replacing the battery (turns on by itself).
It seems that your power button is busted. I had the same problem, though I manage to have a way to make things alright. If youre on a CM9/C10 youre good. Download button remapper at remap the capacitive search button and make it act as a power button. So, if you're waking up the phone you will use the volume rockers and if you want to sleep and lock, use the search soft key.
takeoutttt said:
It seems that your power button is busted. I had the same problem, though I manage to have a way to make things alright. If youre on a CM9/C10 youre good. Download button remapper at remap the capacitive search button and make it act as a power button. So, if you're waking up the phone you will use the volume rockers and if you want to sleep and lock, use the search soft key.
Click to expand...
Click to collapse
Where do you get button mapper?
Sent from my SPH-D710 using xda app-developers app
DaMan90 said:
Where do you get button mapper?
Sent from my SPH-D710 using xda app-developers app
Click to expand...
Click to collapse
You can search in this forum, use the search button above. I got mine by downloading in BlackMart app.