Ignore this thread.... Duplicate - Captivate Q&A, Help & Troubleshooting

Recently, I had a very long discussion with some helpful users regarding how my market disappeared in the Android Themes section. After never recovering my stock market application, I finally just flashed to the cognition rom that is built for 2.1.
This was a huge risk for me because for some reason my phone is not found in Odin when it is in download mode. I have already tried everything to get it recognized, but nothing was able to get it recognized. If I were to brick my phone, I don't think I could fix it. I soft bricked it during the problem with the Market, but luckily I was able to get the phone working again through recovery.
I am thinking of flashing to the new cognition so that I can get my phone running on a 2.2 based rom and then quit flashing until I get a better phone or figure out my Odin problems.
I just have a few questions. I know a lot of people recommend flashing to stock first (which I can't do), while others don't flash stock. I should be able to just disable Voodoo and hopefully flash successfully to a new rom, correct? Also, what are the chances of a permanent brick? As long as I could get into recovery I could probably get the phone back up again without the use of Odin, right?

Well, first, this belongs in Q&A but...
It sounds like you have nothing to lose at this point. A lot of people flash roms without going back to stock, myself included. Disabling lagix is recommended though. I've seen a few people have issues going from 2.2.1 to 2.2 so keep that in mind if you're currently running 2.2.1.
As far as bricking your phone, it's always a possibility. Proceed with caution.
As a side, did you try to battery pull method to get Odin to recognize your phone?

lrs421 said:
Well, first, this belongs in Q&A but...
It sounds like you have nothing to lose at this point. A lot of people flash roms without going back to stock, myself included. Disabling lagix is recommended though. I've seen a few people have issues going from 2.2.1 to 2.2 so keep that in mind if you're currently running 2.2.1.
As far as bricking your phone, it's always a possibility. Proceed with caution.
As a side, did you try to battery pull method to get Odin to recognize your phone?
Click to expand...
Click to collapse
Is 2.2.1 the same as 2.1update-1? Thats what I have...
What is the battery pull method? I may have tried it, but I can't remember.

yentlequible said:
Is 2.2.1 the same as 2.1update-1? Thats what I have...
What is the battery pull method? I may have tried it, but I can't remember.
Click to expand...
Click to collapse
Sounds like your running eclair. Do this to get into download mode.
Open stock Odin.
Power off the phone.
Remove the battery.
Connect your phone to your computer via USB.
While holding down the volume up and down buttons simultaneously re-insert the battery.
Odin should now recognize your phone and allow you to flash back to stock.
I haven't done that in a while.
Sent from my liberated Captivate via XDA App.

lrs421 said:
Sounds like your running eclair. Do this to get into download mode.
Open stock Odin.
Power off the phone.
Remove the battery.
Connect your phone to your computer via USB.
While holding down the volume up and down buttons simultaneously re-insert the battery.
Odin should now recognize your phone and allow you to flash back to stock.
I haven't done that in a while.
Sent from my liberated Captivate via XDA App.
Click to expand...
Click to collapse
Ok, ill try this out.
Also, I apologize for making this in the wrong forum. I got confused and thought that it would be a good place if I was discussing a roms.

yentlequible said:
Ok, ill try this out.
Also, I apologize for making this in the wrong forum. I got confused and thought that it would be a good place if I was discussing a roms.
Click to expand...
Click to collapse
Good luck . Their friendly in q&a too
Sent from my liberated Captivate via XDA App.

lrs421 said:
Good luck . Their friendly in q&a too
Sent from my liberated Captivate via XDA App.
Click to expand...
Click to collapse
Wasn't recognized....
Ill go take this over to the Q&A section...

Related

Build 1010 Will Not Go Into DL Mode!!!

Few days ago I rooted and put Serendipity 2.0 on my Build 1010 with no problems.
I want to try Cognition 3.01.
So I followed the SAME method used in the MobileTechVideos and I cannot figure out how to get it into download mode
I have tried the 3 button method several times and it just takes me to the battery charging icon.
------
Would I be able to just pull up Odin3 (I897UCJF6-final-OCD-REV0) .exe as administrator, plug in USB, turn on phone, and go to DL mode through the phone via that way? Would it recognize it on my computer so I can just go back to stock and do the entire process over again for a ROM?
Or is this easier: http://forum.xda-developers.com/showthread.php?t=818439
Would going to download manager through my phone while having Odin3 pulled up on the computer and my USB of course plugged in, work???
Please, someone, anyone!!! Wanting to try a new ROM so bad!!!
I would flash back to stock and start fresh
Have you used odin before?
I can get you into download mode and going with odin if your phone is working and recognized by your computer but with your build you don't want to use the odin you linked I am pretty sure.
crupp said:
I would flash back to stock and start fresh
Click to expand...
Click to collapse
That's what I'm trying to do!!! I just need to get into download mode first. My phone is not bricked or anything; it's working great. I just need to get into download mode so I go back to stock and put a new ROM on!!!
I think it's because of my build, 1010.
Can anyone confirm C3POs (Odin3) method works?
xThe Enforcer said:
Few days ago I rooted and put Serendipity 2.0 on my Build 1010 with no problems.
<snip>
Would I be able to just pull up Odin3 (I897UCJF6-final-OCD-REV0) .exe as administrator, plug in USB, turn on phone, and go to DL mode through the phone via that way? Would it recognize it on my computer so I can just go back to stock and do the entire process over again for a ROM?
Click to expand...
Click to collapse
You would probably end up with a brick.
See: http://forum.xda-developers.com/showpost.php?p=10056254&postcount=36
And, BTW, there is no need to flash stock before flashing Cognition, but it's still good to find a reliable way in case you ever have a real need to do so. Also, I'm pretty sure Cognition still includes and sbl.bin that will fix your button combos (that's not normally a good thing, but in your case it is).
xThe Enforcer said:
That's what I'm trying to do!!! I just need to get into download mode first. My phone is not bricked or anything; it's working great. I just need to get into download mode so I go back to stock and put a new ROM on!!!
I think it's because of my build, 1010.
Can anyone confirm C3POs (Odin3) method works?
Click to expand...
Click to collapse
I also have 010 and have flashed half a dozen rooms and used 3 button for all of them including Cog 3
opcow said:
You would probably end up with a brick.
See: http://forum.xda-developers.com/showpost.php?p=10056254&postcount=36
And, BTW, there is no need to flash stock before flashing Cognition, but it's still good to find a reliable way in case you ever have a real need to do so. Also, I'm pretty sure Cognition still includes and sbl.bin that will fix your button combos (that's not normally a good thing, but in your case it is).
Click to expand...
Click to collapse
Thanks for the link.
So bottom line; just use a different Odin3. Just like I originally posted:
http://forum.xda-developers.com/showpost.php?p=10056254&postcount=36
Same concept.
crupp said:
I also have 010 and have flashed half a dozen rooms and used 3 button for all of them including Cog 3
Click to expand...
Click to collapse
Every phone is different. I've read of someone with 1008 not having 3 button.
opcow said:
You would probably end up with a brick.
See: http://forum.xda-developers.com/showpost.php?p=10056254&postcount=36
And, BTW, there is no need to flash stock before flashing Cognition, but it's still good to find a reliable way in case you ever have a real need to do so. Also, I'm pretty sure Cognition still includes and sbl.bin that will fix your button combos (that's not normally a good thing, but in your case it is).
Click to expand...
Click to collapse
And also, I disagree. Every ALWAYS says to flash to stock no matter what...
xThe Enforcer said:
And also, I disagree. Every ALWAYS says to flash to stock no matter what...
Click to expand...
Click to collapse
Not everyone. It's apparently mainly confined to the Captivate forums and not universally recommended even here (Darky's instructions say nothing about it, for example). There is no benefit to doing so, believe it or not. Of course I don't care how anyone does it. It's up to you. If you tell people it's safer, however, you're misinforming people based on something that got started months ago and just became the status quo.
http://forum.xda-developers.com/showpost.php?p=10056254&postcount=36
I believe this is what im looking for. I couldn't find the pit nor tar files any where. Im a vibrant owner so not to familiar with the files. Thanks. Will let you know.
Sent from my SGH-T959 using XDA App
Well bottom line, I think the easiest method for me to get into download mode every time I want to root/flash is by using the 99 cent jig. Thanks everyone for there info.
So I got into download mode by installing a 3buttonfix.zip via CWM.
I used Odin3 exactly like your supposed to. Went to stock, master cleared. Everything passed and completed.
My phone is now back to stock but still showing all files on my SD card. I even tried a factory reset and it still shows them.
Any ideas?
Blah, still no one?
*2767*3855#
This is the code you can enter in the dialer to wipe the phone internal memory. Does not ask for confirmation so make sure you have already done a backup of what you want.
newter55 said:
*2767*3855#
This is the code you can enter in the dialer to wipe the phone internal memory. Does not ask for confirmation so make sure you have already done a backup of what you want.
Click to expand...
Click to collapse
Outstanding. It worked and did actually delete everything on my SD card. It's odd how Master Clear and factory reset through the phone did not but this way did. Build 1010 is bipolar.
Appreciate all the help everyone!
(I gave you a 'thanks' Newter)

[Q] Brick

I am wondering how easy it is to brick my Captivate. Also, how easy is it to brick the phone, with the only solution being to use a JIG?
Is the only way to brick if you do something stupid? If you follow all instructions (flash to stock, etc.) is it even possible to brick it? I've upgraded my phone to 2.2 using Kies; does the fact that I've upgraded once make it muc less likely to fail and brick later?
I'm wondering this because all the ROM makers must flash constantly, so I'm thinking there must be a way to avoid bricks.
Thank you!
AmandeepG said:
I am wondering how easy it is to brick my Captivate. Also, how easy is it to brick the phone, with the only solution being to use a JIG?
Is the only way to brick if you do something stupid? If you follow all instructions (flash to stock, etc.) is it even possible to brick it? I've upgraded my phone to 2.2 using Kies; does the fact that I've upgraded once make it muc less likely to fail and brick later?
I'm wondering this because all the ROM makers must flash constantly, so I'm thinking there must be a way to avoid bricks.
Thank you!
Click to expand...
Click to collapse
Depends on your Captivate. In general, it's a bad idea to flash back to stock unless absolutely necessary. Bad Odin flashes are one of the biggest causes of bricked Captivates. Bad flashes through other methods (like CWM) usually leave you with boot problems, but working button combos for download mode. You should also check beforehand that your button combos work, since some Captivates are without them out of the box.
Also, wrong forum. This belongs in Q&A.
GGXtreme said:
Bad Odin flashes are one of the biggest causes of bricked Captivates.
Click to expand...
Click to collapse
Isn't the accepted way (as in the stickied thread) to always flash to stock?
GGXtreme said:
You should also check beforehand that your button combos work, since some Captivates are without them out of the box.
Click to expand...
Click to collapse
"Hold down both volume buttons and while holding them down plug the phone in." works for me
I have bricked my phone to the point of needing a jig 3 times now all because of odin. But the jig is 99 cents and is easy to use
sent from my captivate running a kitchen rom and hardcores 256hz k12n
kschumake83 said:
But the jig is 99 cents and is easy to use
Click to expand...
Click to collapse
Can you buy it, or do you have to make it from components?
Flashing back to stock is only needed when you have to, but no you do not have to flash to stock every time you flash a rom, a bad odin flash is usually the main cause in a bricked phone.. But as long as you can get to recovery or download mode, then its not bricked, you can usually get something flashed either way
existz said:
Flashing back to stock is only needed when you have to, but no you do not have to flash to stock every time you flash a rom, a bad odin flash is usually the main cause in a bricked phone.. But as long as you can get to recovery or download mode, then its not bricked, you can usually get something flashed either way
Click to expand...
Click to collapse
But the stickied thread says the exact opposite. I'm a little confused.
nbs11 said:
Here is the rule of thumb: if it does not specifically say anything about being able to not use ODIN in the original thread for the ROM you MUST you ODIN.
Click to expand...
Click to collapse
AmandeepG said:
But the stickied thread says the exact opposite. I'm a little confused.
Click to expand...
Click to collapse
Sometimes personal habit becomes the correct way to do something. For instance one teacher teaching how to count with pictures of apples and the other using oranges.
GGXtreme said:
Bad Odin flashes are one of the biggest causes of bricked Captivates. Bad flashes through other methods (like CWM) usually leave you with boot problems, but working button combos for download mode.
Click to expand...
Click to collapse
Do these "bad" flashes occur do to doing improper things, like pulling the cable mid-update, or forgetting to unlagfix before, or stuff like that? Or are they purely random?
Normally The bad flashes from odin are due to the fact the the phone being flashed did not have the 3 button combo by default. I personally have flashed ALOT and always odin and master clear before a new rom, the only time I bricked and needed a jig was when I had my old phone (got it replaced) that didnt have the 3 button and used the wrong odin.
zelendel said:
Normally The bad flashes from odin are due to the fact the the phone being flashed did not have the 3 button combo by default. I personally have flashed ALOT and always odin and master clear before a new rom, the only time I bricked and needed a jig was when I had my old phone (got it replaced) that didnt have the 3 button and used the wrong odin.
Click to expand...
Click to collapse
Thanks! I'm gonna check if my Captivate has this 3 button recovery mode.
If it does, is the 3 button way just as effective as a JIG? And how effective is the 3 button and JIG at recovering from bricks (like I mean, how possible is it that they will not work)
AmandeepG said:
Can you buy it, or do you have to make it from components?
Click to expand...
Click to collapse
you can buy jigs online people sell for 20$ or so...but it's actually very simple to make and so cheap as well so buying one is slightly pointless. also, i have flashed too many roms i've lost track, my phone shutdown in the middle of an odin, etc etc, and i always manage to get out of it so i wouldn't be concerned. having 3button enabled helps tho
AmandeepG said:
Thanks! I'm gonna check if my Captivate has this 3 button recovery mode.
If it does, is the 3 button way just as effective as a JIG? And how effective is the 3 button and JIG at recovering from bricks (like I mean, how possible is it that they will not work)
Click to expand...
Click to collapse
I am guessing that you are concerned with bricking yours. You must be thinking about flashing a rom for the first time. I needed the jig yesterday for the first time. From what I understand, the jig method is almost a guarantee fir download mode, making the captivate nearly unbrickable. Can it be bricked... I am sure it can, but you are part of a community full of resources to keep you from doing so. You trepidation is not unique... I too was slow to flash my captivate. Now that I have, I have a phone that I love. I have been able to contribute to the community. And... I have a new found addiction.
Hi. My username is NunHugger and I am a flashaholic.
Sent from my SGH-I897 using XDA App
NunHugger said:
I am guessing that you are concerned with bricking yours. You must be thinking about flashing a rom for the first time.
Click to expand...
Click to collapse
You are completely right there!
I think I'll hold off doing my first flash until I can go out and get the parts for the jig, make and test it, so I can be sure nothing bad will happen
zelendel said:
Normally The bad flashes from odin are due to the fact the the phone being flashed did not have the 3 button combo by default. I personally have flashed ALOT and always odin and master clear before a new rom, the only time I bricked and needed a jig was when I had my old phone (got it replaced) that didnt have the 3 button and used the wrong odin.
Click to expand...
Click to collapse
Same here...corrupted data is corrupted data..and will cause problems...no matter how it gets loaded ...I've have been using Odin since I came to the Captivate..and is the only way I have been able to actually enjoy a new rom..A new rom...a fresh install..less problems for me.
Mac
A question about download mode:
I want to test if my captivate can get into download mode by the 3-button combo. However, I don't have any zips to update or anything to download or anything like that.
How do I enter download mode and then exit without making any modifications?
I thought I could just power the phone off, but in big letters it says "Do not power off target" (in videos I've watched).
AmandeepG said:
Isn't the accepted way (as in the stickied thread) to always flash to stock?
Click to expand...
Click to collapse
Accepted, yes.
Stupiud, yes.
You don't need anything to flash to get into DL mode
Just follow the instructions as it says and if it comes up you can just reboot the phone. Although you have to pull the battery. Although I've heard that holding just the Vol Up and Power for 10 secs also works. I've never tried it though
AmandeepG said:
Do these "bad" flashes occur do to doing improper things, like pulling the cable mid-update, or forgetting to unlagfix before, or stuff like that? Or are they purely random?
Click to expand...
Click to collapse
Depends on a lot of factors. It could be that your Captivate doesn't support flashing back to earlier than JH2 (JF6 one-click will brick), that your Captivate is already missing button combos (requires C3P0LOL's fixed Odin or AT&T's OTA JH7 update), a bad USB cable, problems with Windows, using the wrong USB port, etc. (all on top of user error). Lagfix won't affect Odin flashes.
AmandeepG said:
Do these "bad" flashes occur do to doing improper things, like pulling the cable mid-update, or forgetting to unlagfix before, or stuff like that? Or are they purely random?
Click to expand...
Click to collapse
I wouldn't say they are random. They are probably mostly caused by user error or some fault in the USB chain (port, cable, driver interactions). Whatever the root cause, from what I can see almost all bricks/semibricks are the result of using odin (I include cases such as where a cwm flash results in a boot loop and the user can recover because he used one-click and has no button combos).

[Q] Flashing to Cognition 3 without flashing stock?

Recently, I had a very long discussion with some helpful users regarding how my market disappeared in the Android Themes section. After never recovering my stock market application, I finally just flashed to the cognition rom that is built for 2.1.
This was a huge risk for me because for some reason my phone is not found in Odin when it is in download mode. I have already tried everything to get it recognized, but nothing was able to get it recognized. If I were to brick my phone, I don't think I could fix it. I soft bricked it during the problem with the Market, but luckily I was able to get the phone working again through recovery.
I am thinking of flashing to the new cognition so that I can get my phone running on a 2.2 based rom and then quit flashing until I get a better phone or figure out my Odin problems.
I just have a few questions. I know a lot of people recommend flashing to stock first (which I can't do), while others don't flash stock. I should be able to just disable Voodoo and hopefully flash successfully to a new rom, correct? Also, what are the chances of a permanent brick? As long as I could get into recovery I could probably get the phone back up again without the use of Odin, right?
yentlequible said:
Recently, I had a very long discussion with some helpful users regarding how my market disappeared in the Android Themes section. After never recovering my stock market application, I finally just flashed to the cognition rom that is built for 2.1.
This was a huge risk for me because for some reason my phone is not found in Odin when it is in download mode. I have already tried everything to get it recognized, but nothing was able to get it recognized. If I were to brick my phone, I don't think I could fix it. I soft bricked it during the problem with the Market, but luckily I was able to get the phone working again through recovery.
I am thinking of flashing to the new cognition so that I can get my phone running on a 2.2 based rom and then quit flashing until I get a better phone or figure out my Odin problems.
I just have a few questions. I know a lot of people recommend flashing to stock first (which I can't do), while others don't flash stock. I should be able to just disable Voodoo and hopefully flash successfully to a new rom, correct? Also, what are the chances of a permanent brick? As long as I could get into recovery I could probably get the phone back up again without the use of Odin, right?
Click to expand...
Click to collapse
<<< this might not be helpful, but I will tell you my situation... >>>
I have tried to Rom my JI6 (unoffical froyo) version of captivate, with Cog v2.3b8, using ROM manager.
But after installation, my screen went blank and the battery started to heat up...
After that I was lazy to fix it myself, so I went to exchange shop, and changed it...
- if your phone bricks (forever) try this : http://forum.xda-developers.com/showthread.php?t=775911
peurocs4 said:
<<< this might not be helpful, but I will tell you my situation... >>>
I have tried to Rom my JI6 (unoffical froyo) version of captivate, with Cog v2.3b8, using ROM manager.
But after installation, my screen went blank and the battery started to heat up...
After that I was lazy to fix it myself, so I went to exchange shop, and changed it...
- if your phone bricks (forever) try this : http://forum.xda-developers.com/showthread.php?t=775911
Click to expand...
Click to collapse
I tried that same method and it still did not show up in odin.
Sent from my SAMSUNG-SGH-I897 using XDA App
yentlequible said:
I tried that same method and it still did not show up in odin.
Sent from my SAMSUNG-SGH-I897 using XDA App
Click to expand...
Click to collapse
Main problem with your Captivate is that you cannot connect to your PC???
Did you tried using different computer, or using different version of Windows/Mac?
<Sorry, if I'm not really helping you...>
peurocs4 said:
Main problem with your Captivate is that you cannot connect to your PC???
Did you tried using different computer, or using different version of Windows/Mac?
<Sorry, if I'm not really helping you...>
Click to expand...
Click to collapse
Back when I was really trying to figure the problem out (about 2 months ago), I was trying everything mentioned. I tried different versions of odin, 3 separate computers, windows xp/vista/7, front and back usb ports, multiple drivers, etc... The weird thing is that the phone is recognized in odin when it is on, which is how I was able to do a master clear on it. It is just when it is in download mode that it does not recognize it.
I eventually just gave up thinking that it was just a problem my phone has. The only thing I have not been able to test is using a different cable. I have been using the original OEM one, but I guess it could be the problem.
When did you bought the device?
if its within a year... you can exchange it... this looks like easy way out.
Sent from My Captivate
삼성 겔렉시에서 보냄
peurocs4 said:
When did you bought the device?
if its within a year... you can exchange it... this looks like easy way out.
Sent from My Captivate
삼성 겔렉시에서 보냄
Click to expand...
Click to collapse
Unfortunately, It was purchased off contract and used from someone who lived near me. It is less than a year old, I just don't have the receipt for it. I would say that I bought it around the beginning of last August. They guy who sold it said he only used it for 2 weeks.
Ok, im just going to risk it... Phone should be flashed within the next 10 minutes or so.
yentlequible said:
Ok, im just going to risk it... Phone should be flashed within the next 10 minutes or so.
Click to expand...
Click to collapse
I had the same prob at first and what i found is that I had to remove the drivers and then let windows 7 reinstall the drivers on its own again after turning debugging on, then used Odin to activate DL mode and let those drivers install as well
zelendel said:
I had the same prob at first and what i found is that I had to remove the drivers and then let windows 7 reinstall the drivers on its own again after turning debugging on, then used Odin to activate DL mode and let those drivers install as well
Click to expand...
Click to collapse
How do you use Odin to activate DL mode? I was unaware that it could do that...

no longer get in download or recover

I recieved a replacement captivate today. It was a 1011 build. Recovery and download worked fine. It was running 2.2.
I used the one click odin to flash to stock 2.1 and now I can no longer get in download mode or recovery with any key combo.
What can I do to fix this? Kinda freaked out, been flashing roms for months and months with zero issues so I am not real sure how to resolve this one.
To clarify, I can use adb to get into download or recovery I am sure and thats what I am going to do. Then flash the 3 button combo fix with Odin that C3P0LOL put together.
My question is I never had this on my 1007 build. What did I do wrong and what can I do to prevent this from every happening in the future? If the fix works and I avoid the one click odin, I should be good to go from now on right? Sucks. I tested everything before I flashed one click to 2.1 which is kinda stupid I guess.
what about holding vol up and down and inserting usb?
maybe your 3button was killed by the odin 1 click... but it still shouldve rebooted...
try the steps in this thread...
http://forum.xda-developers.com/showthread.php?t=775911
B-Naughty said:
what about holding vol up and down and inserting usb?
try the steps in this thread...
http://forum.xda-developers.com/showthread.php?t=775911
Click to expand...
Click to collapse
That is what I was doing and does not work. On my old captivate, I couldnt even count the times I did this so it's not user error. Guess its good I had such good success for so long as this is the time you learn stuff! I really dont want to learn today I just want it to work?!!
gocats7 said:
That is what I was doing and does not work. On my old captivate, I couldnt even count the times I did this so it's not user error. Guess its good I had such good success for so long as this is the time you learn stuff! I really dont want to learn today I just want it to work?!!
Click to expand...
Click to collapse
yea it's a little wierd the odin finsihed and didnt reboot the phone... and now 3button won't work... some phones just wanna act wierd... ive done everything in the world to mine including yank the cord during a bad flash... never lost 3 button or download... 1011 build...
tried holding the vol buttons and hookin usb then insert batt? hope u get it goin... keep us posted...
Flashed back to stock using the loader I referenced earlier and now I have both download and recovery key combinations.
I am speculatiing that coming from 2.2 to 2.1 with the one click was a bad idea. All I had done was root the phone to that point. If anyone knows 100% what the deal was I would like to know. I went from 2.2 to 2.1 because I couldnt get clockwork to work and I read that was an issue on 2.2. I am sure there was a better way but thats what came to me.
I would guess that using the thread below to go back to stock from now on to not risk screwing up my 3 button combos would be the best idea, anyone?
http://forum.xda-developers.com/showthread.php?t=995143
One question, if I want to go back to stock 2.2 as the phone came with is there a thread for that? I looked and so far didnt find it. Probably need to just keep looking but thought what the heck, would ask since I came this far.

Someone please help newb with brick

I have been looking through the threads, and havent seen what I am looking for. So hopefully i will not get flamed to bad. I tried to install mikeymikes GR12, I got through the first stage of downloading the gingerbread rom to the phone through odin, but then it went south. I lost root and was unable to get back to the download screen. I then tried to use the all in one tool to root the phone, and that put me to the recovery screen where i could not use the ok button, just the volume up and down buttons. I just managed to get the download screen to come back, but i cant get anything else to work. Any suggestions on what to do, where to go from here.
Thank you for your help
I would go back to stock first. I believe your problem lies in the bootloaders. There are two bootloaders in the beginning and if you don't have the gingerbread ones installed, you won't install gingerbread properly.
I would use DesignGears One Click Odin to go back to stock and load the Froyo drivers. http://forum.xda-developers.com/showthread.php?t=731989. Make sure you open up Odin first before plugging in your phone, then hit the Start button.
Once that is done, you can try again, but read about getting the GB bootloaders installed properly before you try to flash a GB ROM. Any of the GB ROM instructions should get you there. Just make sure you know all the steps before you try it again.
Good Luck!!
I don't see why you would be flamed for your question. That is what Q&A is for and you are in a bad spot. The biggest thing to remember is to be as specific as possible when you post a question. This includes what you were trying to do, what steps you took, what was the result, when did the problem occur (which step) and what you have tried to do, if anything to fix it.
One more thing. It is always possible that the USB cable is bad or that the USB port you are plugging into (on the computer) isn't working properly. You might also want to plug into a different USB port.
Sorry these posts are broken up, but as I'm coming up with ideas, I'm posting.
Here's something you should try:
(I wrote this for Team Phoenix, hence the sig.. But it works the same with every ROM. There's a link to a very nice tutorial I suggest you follow).
http://forum.xda-developers.com/showpost.php?p=13503747&postcount=2
Hope it helps
You guys are awesome, Odin one click worked, It's on eclair, but it works! Thank you again
donkeyboy said:
You guys are awesome, Odin one click worked, It's on eclair, but it works! Thank you again
Click to expand...
Click to collapse
Glad it worked!
Make sure you read and understand before going forward with flashing
Otherwise... well.. I'll still be in here ready to help lol
BWolf56 said:
Glad it worked!
Make sure you read and understand before going forward with flashing
Otherwise... well.. I'll still be in here ready to help lol
Click to expand...
Click to collapse
Me too. If we can ... Remember not all things can be recovered from so please read everything twice before ever touching your phone.
10-4. My next question is: where do I get froyo from. Kies sees my eclair version as unregistered, so it wont update. And my ota sees an update is needed, but when i tried, the area im in has crappy signal, so the update failed and now i have to wait 24 hours to do it.
Any suggestions?
Thanks again
are you planning on flashing a custom rom?
if so updating to official froyo is A HUGE WASTE OF TIME
EDIT:are you Canadian by chance? if so check this thread:http://forum.xda-developers.com/showthread.php?t=979133
I only plan to root the official froyo right now, that is what I had before I jacked it up. I am not Canadian.
donkeyboy said:
I only plan to root the official froyo right now, that is what I had before I jacked it up. I am not Canadian.
Click to expand...
Click to collapse
Going on official froyo will get you the signature failed error (which you need the 3e recovery fix if you ever want to flash a custom ROM).
So, basically, if you want more than 2.2 official release. We suggest you don't update. If you're perfectly fine staying on 2.2 Froyo, then there's no problem lol
As for Kies, you shouldn't have any problem using Kies mini. Other than that, there is a 2.2 flash around here. I'm sure you'll find it doing a little search
I had root on my official froyo for a couple of months without a problem. Right now i cant get my phone to go into download mode, it only goes to the battery screen. If i can get to download i can make some headway
donkeyboy said:
I had root on my official froyo for a couple of months without a problem. Right now i cant get my phone to go into download mode, it only goes to the battery screen. If i can get to download i can make some headway
Click to expand...
Click to collapse
If the battery pull way isn't working. You could always go read on abd. It send SU commands and you could get your phone in downlaod mode that way.
Is there an easy way to get adb without getting the sdk. I downloaded the sdk and it keeps saying i need java, when i download the java crap it says the same thing.
donkeyboy said:
Is there an easy way to get adb without getting the sdk. I downloaded the sdk and it keeps saying i need java, when i download the java crap it says the same thing.
Click to expand...
Click to collapse
Did you reboot your pc?
Yes i did, no change
i believe you need microsoft .net framework installed also...
easy adb setup link in my sig.
files and everything needed to get going.
you may want to build a jig yourself or buy one online just in case:
MOD EDIT: No links to commercial products please.

Categories

Resources