Database Develop

[Q] ROM Manager Signature Verification Failure

A few weeks ago I flashed the Cognition V2.2 ROM and everything was fine until it started getting twitchy a few days ago. I tried to use the ROM Manager to restore the backup that was created during the flash but I keep getting the same error message and the phone does not seem to go into the Clockwork Mod Recovery but stays in the Android system recovery. The message says that the whole-file signature has failed to verify and that the installation was aborted. Does anyone have any idea how I can get my phone back to normal?

gtcochran said:
A few weeks ago I flashed the Cognition V2.2 ROM and everything was fine until it started getting twitchy a few days ago. I tried to use the ROM Manager to restore the backup that was created during the flash but I keep getting the same error message and the phone does not seem to go into the Clockwork Mod Recovery but stays in the Android system recovery. The message says that the whole-file signature has failed to verify and that the installation was aborted. Does anyone have any idea how I can get my phone back to normal?
Click to expand...
Click to collapse
Common knowledge that the version of Cognition you are running is not supported by ROM Manager, it is 3e recovery and Clockwork needs 2e. You can update to the newer Cognition which has 2e recovery. I recommend you read the facts sheet befor flashing, the method you should use is Odin one click back to stock http://forum.xda-developers.com/showthread.php?t=731989, then master clear so that nothing is lingering from your previous setup, backup everything from your internal storage to your pc first, this will wipe everything from your internal, replace it after you finish Master clear. you should only replace the update.zip, ClockworkMod and your music, photo's and that stuff. Backup your apps using Titanium Backup.
Here's the link for the new Cognition http://forum.xda-developers.com/showthread.php?t=786532

So I tried what you recommended and got my phone back to the stock condition but I'm still not able to use ROM manager or flash another ROM. After I root the phone I install ROM Manager, flash it to the current edition and then try to reboot into recovery but when it gets to recovery it gives the following error message...
--Installing from package...
Finding update package...
Opening update package...
E:Can't open /cache/update.zip
(bad)
Installation aborted
Also the header of the screen states that I am in Android system recovery <2e>. If I am not mistaken, shouldn't I be in recovery <3e>? If so how do I get there? I've tried flashing the stock Kernel but that didn't work and I even installed the internal betas correctly but no cigar.

gtcochran said:
Also the header of the screen states that I am in Android system recovery <2e>. If I am not mistaken, shouldn't I be in recovery <3e>? If so how do I get there? I've tried flashing the stock Kernel but that didn't work and I even installed the internal betas correctly but no cigar.
Click to expand...
Click to collapse
did you really read Rhi's post?
in order to use rom manager (clockwork mod) you must be using 2e!
my brain hurts from all the lack of searching people in this forum seem to have a problem with

Pirateghost said:
did you really read Rhi's post?
in order to use rom manager (clockwork mod) you must be using 2e!
my brain hurts from all the lack of searching people in this forum seem to have a problem with
Click to expand...
Click to collapse
LOL, +1

Touche, but the error still remains. Does anyone have any positive ideas? Like I stated before, I still cannot put my phone into clockwork mod recovery.

gtcochran said:
Touche, but the error still remains. Does anyone have any positive ideas? Like I stated before, I still cannot put my phone into clockwork mod recovery.
Click to expand...
Click to collapse
so put it in download mode, and use ODIN one click back to stock...then leave it the hell alone....

Like I said, I've already used Odin. Everything is back to stock except for the Kernel and a stock kernel install with Odin doesn't seem to work. Odin says that the install passed but nothing changes on the phone itself. All things considered, the phone is stock but not capable of going into Clockwork Mod recovery.

gtcochran said:
Like I said, I've already used Odin. Everything is back to stock except for the Kernel and a stock kernel install with Odin doesn't seem to work. Odin says that the install passed but nothing changes on the phone itself. All things considered, the phone is stock but not capable of going into Clockwork Mod recovery.
Click to expand...
Click to collapse
When you go into stock recovery now is it version 2e or 3e?

gtcochran said:
Like I said, I've already used Odin. Everything is back to stock except for the Kernel and a stock kernel install with Odin doesn't seem to work. Odin says that the install passed but nothing changes on the phone itself. All things considered, the phone is stock but not capable of going into Clockwork Mod recovery.
Click to expand...
Click to collapse
if you used the one click back to stock then you are on the stock kernel.....what makes you think you are not on the stock kernel?

The recovery is 2e
I believe that the kernel is not stock because when I look at the phone information it says that the kernel is
2.6.29
[email protected] #2
I'm not sure that it is stock or not but my gut tells me that it isn't.

gtcochran said:
The recovery is 2e
I believe that the kernel is not stock because when I look at the phone information it says that the kernel is
2.6.29
[email protected] #2
I'm not sure that it is stock or not but my gut tells me that it isn't.
Click to expand...
Click to collapse
Rom manager will work just fine with 2e recovery. Just delete any update.zip files you have in your home directory - then open rom manager and reflash clockworkmod the cappy - then you should be good to go.
As for whether or not that is the stock kernel I am not sure, but how can you tell just by looking at it if you don't know which kernel is the stock one?

I've mounted my internal and external sd cards and removed any updates but it still gives the same error. After I used the odin one-click to flash the stock rom I used the master clear as recommended. Now, if I am not mistaken, shouldn't that erase all of my user data? I reinstalled my espn app so I could follow my football team and the app still remembered my preferences and favorites. This makes me think that the master clear did not finish the job. Thoughts?

gtcochran said:
I've mounted my internal and external sd cards and removed any updates but it still gives the same error. After I used the odin one-click to flash the stock rom I used the master clear as recommended. Now, if I am not mistaken, shouldn't that erase all of my user data? I reinstalled my espn app so I could follow my football team and the app still remembered my preferences and favorites. This makes me think that the master clear did not finish the job. Thoughts?
Click to expand...
Click to collapse
Master clear should've done that. If you are restoring your apps and settings using Titanium Backup then you are restoring user data which you should not do.
When you Master Clear is your device on and on the home screen, it needs to be. Don't Master Clear in Recovery mode or Download mode or it does nothing. Also you need to have debugging on.
2.6.29
[email protected] #2
That is the stock kernel. Just so you know if you are running stock with root you can simply place the update.zip from the Clockwork folder, you should have backed up before flashing and Master clear, back into your internal. ClockworkMod does fail on first attempt to flash sometimes, it happenned to me the first time I flashed it, the second time worked like a charm. Are you rooted? You need root to use ROM Manager and debugging should be on.

gtcochran said:
I've mounted my internal and external sd cards and removed any updates but it still gives the same error. After I used the odin one-click to flash the stock rom I used the master clear as recommended. Now, if I am not mistaken, shouldn't that erase all of my user data? I reinstalled my espn app so I could follow my football team and the app still remembered my preferences and favorites. This makes me think that the master clear did not finish the job. Thoughts?
Click to expand...
Click to collapse
After you deleted the update.zip then opened rom manager and flashed clockworkmod it should of put a new update.zip on your phone in your home directory - can you confirm that this is the case?
Also you may not have had a successful master clear - you may want to do it again then redo odin3 one click. Also if I am remembering correctly I believe you have the option to clear cache or user data or both in stock recovery you may want to try that as well.

It all works now. The issue was with the master clear. I guess that I did try to run it in the download mode. Thanks a million guys, i really appreciate it.

Maybe I was a bit premature on that. ROM Manager works beautifully but I cannot install updates or flash a custom ROM. The Manager was able to backup the system correctly and enter clockwork mod recovery but it cannot install the update. If the update is on the internal SD it says that...
E:Can't open /sdcard/update.zip
(bad)
and if the update is on the external SD it says that there is no such file or directory. Am I doing it wrong or is there still an underlying issue?

gtcochran said:
Maybe I was a bit premature on that. ROM Manager works beautifully but I cannot install updates or flash a custom ROM. The Manager was able to backup the system correctly and enter clockwork mod recovery but it cannot install the update. If the update is on the internal SD it says that...
E:Can't open /sdcard/update.zip
(bad)
and if the update is on the external SD it says that there is no such file or directory. Am I doing it wrong or is there still an underlying issue?
Click to expand...
Click to collapse
/sdcard/update.zip should only boot into clockwork recovery from stock recovery or boot to stock recovery from clockwork recovery if you flashed clockworkmod correctly from rom manager - and so long as you are not renaming any other files as update.zip after you flash clockworkmod recovery.
Which custom rom are you attempting to install?

I got it. The zip file was corrupted. Now, should I be able to boot into normal clockwork mod recovery with the Cognition 2.2 Beta 7 cuz when I try clockwork recovery it boots into normal recovery? I'm still a little hazy about all this.

gtcochran said:
I got it. The zip file was corrupted. Now, should I be able to boot into normal clockwork mod recovery with the Cognition 2.2 Beta 7 cuz when I try clockwork recovery it boots into normal recovery? I'm still a little hazy about all this.
Click to expand...
Click to collapse
When you first boot into recovery it should be stock recovery. While in stock recovery when you select reinstall packages it will reboot into clockwork recovery - if you flashed clockworkmod recovery correctly from rom manager and it put the appropriate update.zip into your home directory.
And just to note: don't be renaming any files as update.zip if you are using clockwork recovery to flash something.

Darky's ROM Resurrection Edition 9.2 Help! can't get in cwm mode why?

1. Open the Market, and search for 'darky' and download the DarkyROM Configurator
app and install it.
2. After it is installed, open Darky ROM from the App Menu. Select all the options that
you want to install, and deselect the ones you don't want. DO NOT select Wipe as we
have already done that before using ODIN.
3. After selecting and deselecting the options according to your needs, press back to
save and exit Darky ROM app.
4. Copy the file resurrection.zip (extracted from the ROM’s ZIP file you
downloaded at the start) to your internal sd card.
5. Now shut down the phone, and boot into Recovery again. [Vol UP+Home+Power
key]
6. Now select "Install zip from SDCARD
i'm up to step 5, i can't get in cwm mode, i only get in recovery 2e instead, why? pls help me

i can't continue step 6~~ can't install resurrection.zip......... pls help me

somebody pls help me ~~~~~~~~~~~

you need a kernel with cwm to be able to flash this rom.
**DamianGTO Ultimate kernel. 350MB Ram. 600HZ. all ext2. Steam Rom. Js5**

http://forum.xda-developers.com/showthread.php?t=806195
or this http://forum.xda-developers.com/showthread.php?t=823300
flash that then you have cwm

DamianGto said:
you need a kernel with cwm to be able to flash this rom.
**DamianGTO Ultimate kernel. 350MB Ram. 600HZ. all ext2. Steam Rom. Js5**
Click to expand...
Click to collapse
nah~ the thing is this one do not need cwm to flash, they use odin instead(see the link http://forum.xda-developers.com/showthread.php?t=940671). i did successfully install the base rom. the problem is i can't get in voodoo kenel's cwm which is cwm 2.5.1.3 with voodoo lagfix, all i can get in is recovery 2e, and i try apply update.zip, it says no file exist. now how can i be able to get in voodoo's cwm............? i try the quandrant to test the system, and i get 1320, which means the lagfix is on. but i can't get in cwm to turn it off. what can i do now pls help me!~~~ thank u

I would ask Darky its his rom .
jje

Consan said:
http://forum.xda-developers.com/showthread.php?t=806195
or this http://forum.xda-developers.com/showthread.php?t=823300
flash that then you have cwm
Click to expand...
Click to collapse
i flashed this Voodoo-stable-5.4.1-Froyo-2.2.1-GT-I9000-odin-pda.tar, it's still not working, i can not enter the cwm with voodoo, do i need delet any file in my internal sd card before i flash?
the other thing is i found out is i can enter clockworkmod recovery v2.5.1.2 by copying update.zip(the original cwm) file to the internal sd card.

no you should not need to remove anything before. odd that its not working. have you de-bugging mode on!

Consan said:
no you should not need to remove anything before. odd that its not working. have you de-bugging mode on!
Click to expand...
Click to collapse
it's on, but it's not the issue, i use odin to flash it in download mode.....

Did you find a solution yet? I have exactly the same problem. Here's the story:
Brand new SGS, used a few hours stock. Fully charged, then followed the steps darky wrote in his resurrection topic.
HOWEVER, the only thing I did wrong was use Odin from the Samsung site instead of from the package, which caused some problems when I later tried to flash the old way (from a jm9 explaination by richthofen). The PIT would have to be flashed first, but it crashed on this and said do not remove!!!
I had to, because it crashed. I couldnt access recovery, only download. Then I entered download and tried it with the right odin (included in the package by darkyy) and i could flash the phone again following darkyy's steps.
Now the phone works again, with the base rom, but i cannot install the .zip because clockwork does not work properly (as in the beginning). It still has blue text and it misses all the extra options.
Please let me know if you found a solution thanks

Take a look at and follow the steps
http://forum.xda-developers.com/showthread.php?t=734166
Notice that CWM is not permanently installed on the SGS, you should leave the CWM update.zip in you internal card since you will need it everytime you want to use CWM the easiest way is to install rom manager, if you don't and want to do it manually [Up Vol + Home + Power] you will see stock recovery from there you must flash the CWM update.zip which will load CWM and restart the phone into CWM recovery then you can flash any zip using "apply zip from sd card" something like that, hope this helps

[Q] Trying to flash Serendipity 6.3...

I've never flashed a rom before. I currently have stock froyo with the paragon kernel i flashed using the app sgs kernel flasher. I have clockwork mod rom manager, I created a backup of my current rom. So then I tried installing the serendipity rom from the sd card but i get an error message. I read on the sticky on how to flash a custom ROM you need to use ODIN and flash back to stock 2.1 then do a master wipe and re root it and stuff.
Their link to download ODIN is broken so I don't know how to get it. And is there really no other way to flash it besides doing a master wipe and using ODIN?

flash to stock and master clear is not needed. what IS needed are specifics on WHAT error message you get when trying to flash the rom you want

The error message is
"E: failed to verify whole-file signature"
"E: signature verification failed"
"Installation aborted"
Then it brings be to the blue menu so i just select reboot system now

bad download, re-download rom.

May be completely off, but it doesn't sound like you're actually in clockwork mod recovery, but rather stock recovery.
But here's the post with the one click odin with mirrors and I personally would suggest useing it since I generally like to stick to as clean a flash as I can:
http://forum.xda-developers.com/showthread.php?t=731989
Second, I don't know if you've ever seen MobileTechVids tutorial on how to flash custom roms, but I suggest you watch the full series first if you haven't already.
here: http://www.youtube.com/watch?v=MsafJ-9uRqk
I watch the series and try and stick as close to the tut as I can when I'm unsure (or the one provided by the Rom maker as they know what's best for their rom)...
One suggestion, when flashing Serendipity disconnect your phone from cable right before the actual flashing (gave me a glitch in which I couldn't mount storage via usb). Other than that, read read read. I feel it's all I do when it comes to this stuff, but proper research is indispensible.

thresherhorn said:
May be completely off, but it doesn't sound like you're actually in clockwork mod recovery, but rather stock recovery.
Click to expand...
Click to collapse
+1
Is the text on Recovery mode blue or green? If its blue, you're on stock recovery.

+2
Sent from my SGH-I897 using XDA Premium App

Ok I got the stock rom flashed back and rooted it using one click. Now for some reason I can't reboot into clockwork recovery mode. I flashed it successfully. So i click on reboot into recovery and nothing happens. I try clicking on install room from sd card and that doesnt work either

Power off, hold 3 buttons att screen will come on. Keep holding. Screen will go off. Keep holding. Screen comes on again let off the power button but keep the volumes held, this will boot you into stock recovery, since you said you flashed cwm already I'm assuming you mean with rom manager, so the update.zip should be on your sdcard, so just reinstall packages twice and you should boot into cwm.

AIO tools work well and make flashing roms for new people easy and painless
use a search for it

steph2 said:
AIO tools work well and make flashing roms for new people easy and painless
use a search for it
Click to expand...
Click to collapse
+1.
AIO and superoneclick for root/flashing roms makes the process much easier.

crag11 said:
Ok I got the stock rom flashed back and rooted it using one click. Now for some reason I can't reboot into clockwork recovery mode. I flashed it successfully. So i click on reboot into recovery and nothing happens. I try clicking on install room from sd card and that doesnt work either
Click to expand...
Click to collapse
On serendipities main "download" page they have instructions to install. In those instructions is a link to a file you can download. Place that file along with the serendipity 6.3.zip file in the root of your sd card. Use the " 3 button" technique or Rom managers "reboot to recovery" option to get into stock recovery. Hit "reinstall packages" once/possibly twice. That will put you into clockwork mod recovery. Select install zip from sd card, find the serendipity6.3.zip and click power to flash. Confirm. And after it does some stuff it will ask you to reboot. Upon reboot it will as if you want to enable lagfix. Hit plain "Yes". Watch it do its thing and viola...
You have the "dirty" way of how to flash serendipity... But first I please ask you to spend atleast a day reading this forum or others and understanding these instructions and the reasons behind them.

followed instructions off the website and still doesn't work
I was running 2.2 and have done a lot of reading a video watching (thanks Mobile Tech videos) and finally conjured the guts to flash serendipity.
I flashed stock using odin...that went great. Copied the update.zip to sd card. Installed zip twice in 2e recovery. Copied Serendipity.zip file to sd card. started in recovery mode, selected "install from sdcard" selected serendipity.zip file and it seemed to go through that process rather quickly. Then I selected reboot and then everything just started FCing all over the place. Can't even load the stock that I had on there. I don't know what to do. Help please. I can get it back into recovery mode. Tried doing the wipe data/factory reset. That did help either. Help please. I really want to try serendipity. Thanks again in advanced.

Did you run a restore using TiBu at all? Or was it just a straight flash from stock to Serendipity?
Plus, were you running a phone that came with 2.2 out of the box? Or did you upgrade to stock Froyo yourself?

m3thods said:
Did you run a restore using TiBu at all? Or was it just a straight flash from stock to Serendipity?
Plus, were you running a phone that came with 2.2 out of the box? Or did you upgrade to stock Froyo yourself?
Click to expand...
Click to collapse
I did run TB and I had originally flashed up to froyo (took me all night one night) and then went through the process I explained and hit the dead end. I finally was able to get odin to read the phone and flash back to stock. It was a learning process. I realized that I needed not only the Serendipity_6.3.zip file but ALSO the kitchen file to included with it. That wasn't in the directions I don't think. Finally got it all on there. I love it now. I appreciate everyone's help. Any word on a how-to for Bluedipity?

Need help with SGS Looping Issues

Essentially I am at a lost of what to do.
I have tried everything to no prevail which leads to me to my defeat post here for a cry for help.
I DO NOT believe I have bricked it yet because I can still get into download mode and CVM but it doesn't look like this image: http://blog.laptopmag.com/wpress/wp.../Clockwork-Mod-Boot-Screen-e1279545586372.jpg
which is what I wanted. My original plan was to install a new ROM however, I do not have that option "install zip from sdcard". Therefore I had to install the Speedmod Kernel which is why
ANYWAYS moving on, I have tried Heimdall and Odin. I have been able to bootup the phone. HOWEVER it doesn't load a ROM because the Samsung Galaxy GT i9000 logo just keeps looping. Like I said, I am able to get into Download mode and CVM with the new menu. However, when I click anything the screen goes blank and nothing happens. I am at a complete loss of what to do. I have tried everything and I'm looking to advice.
Thanks and hope to hear from you all.

If I remember correctly the Speedmod Kernel uses the power button to select options and if you click the home button the screen will go black.
If this is not the issue then reverting to a stock Rom is probably your best option.
Find a stock Rom at: http://www.sammobile.com/firmware/?page=3&t=1&o=1&m=GT-I9000&r=-1#modelsa (this link is for international version) just select your country. from the links just above Firmwares for GT-I9000 .
From here you want to get a pit 512 & make sure you have a firmware with 3 files (PDA, Phone, CSC) . From here there are plenty tutorials on how to install a stock ROM.
If your issue is not pressing the wrong button in speedmod let me know and I'll be happy to provide a basic list of what to do... or provide a link.

Thanks for the quick reply, I have done that. I have installed the best one I could find: I9000XXJVQ
I put the following 4 files in Odin:
s1_odin_20100512 (PIT)
CODE (PDA)
CSC (CSC)
MODEM (PHONE)
It brings me to Android system recover <3e>. From there I'm at a lost at what to do. I see when it says
Code:
Copying media file
E:failed to mount. /sdcard (File exists)
E:copy_dbdata_media:Can't mount /sdcard you storage not prepared yet. please use UI menu for format and reboot actions.
Media files copy failed.
# MANUAL MODE #
Appling Multi-CSC...
Installing Multi-CSC
Can't access to '/system/csc/BMC/system/'.
Successfully applied multi-CSC.
From there I do not know what to do. When I click reboot system now; nothing occurs, the SGS image at the beginning still continues to loop. I'm looking at how to install the CVM so I can install my custom ROM.
I believe in the past I managed to do it (I installed the Dark Knight mod; but when it booted it said Encryption Unsuccessful and it only happened once. Was never able to get past that screen).
Anyways, that's the instruction from what I did above. What next (It's still looping at the SGS text at the startup).
EDIT:
From this post: http://forum.xda-developers.com/showpost.php?p=9336821&postcount=2
I then followed the install instructions for Root XXJVQ
The thing installed, it still has the issues. Opens the SGS start screen and doesn't go anywhere.
Further EDIT:
I then restarted the phone with following combination. (Power + Vol Up + Home). It then launched in CVM. I cleared partition and cache. I then installed the .zip ROM file (http://forum.xda-developers.com/showthread.php?t=1510940&highlight=cyanogen) from SD card. Rebooted system. It launches. Says "Encryption Unsuccessful" Please restart phone. I click the restart phone button. It restarts, I then get the android looking icon dead on the ground with it's chest open with a "Red triangle !" above it. Stuck from here.

Wish I could help further. In my experience I had to flash stock twice. Once with with pit file and repartition selected. Once without pit file and repartition unchecked.
From there to flash a custom ROM you need to get rid of 3e recovery by flashing something like CF-roof. Then once you have cf-root you can instal custom ROM.
Here is link for cf-root
http://forum.xda-developers.com/showthread.php?p=8238938
Sent from my GT-P7500 using xda premium

I did the above. It boots into CVM. I install the custom ROM. It counts down Waiting for SD Card to mount (20s, 19s, 18s....). Then it just restarts and keeps looping like that. Suggestions?

Unfortunately that is the end of what I know still fairly new to all this. Hourly someone else can help.
Sent from my GT-P7500 using xda premium

Dorianking said:
I did the above. It boots into CVM. I install the custom ROM. It counts down Waiting for SD Card to mount (20s, 19s, 18s....). Then it just restarts and keeps looping like that. Suggestions?
Click to expand...
Click to collapse
HOw long did it take for the ROM to install?
Have you tried removing the battery, battery back in recovery and reflash the ROM.
ICSSGS 4.2 has a requirement to be flashed twice. (different rom but may be similar issue)
Once to update the bootloader which will result in a boot loop when coming from a Gingerbread ROM and again to fully install the rom
Lastly download the ROM again checking the MD5 checksum before flashing
I trust that this will assist

Does it matter if it is installed from the External SD or Internal SD because when I try to install from the internal SD it says "Can't mount /emmc/" so I'm only able to install from the external SD.
I tried installing it twice. I still get the encryption unsuccessful screen. I also re-downloaded the ROM.

OK ii think what you need to do now is try to get the phone to boot successfully into a stock rom for your region.
You mentioned in the first 2 or 3 posts that you did download from SamFirmware a stock rom.
It is probably a Odin flashable ROM
Is it a 3 file or 1 file?
Flash and then boot up the phone to be able to use it.
If successfull move on to the next step.
If you have been able to do this before i would suggest to try a different ROM.
I can personally recomend the ICSSGS 4.2 ROM following the instructions on the opening post for that ROM
If this works then try Dark Knight or other ROM
If this post has helped please use the Thanks Button

Lexrsk said:
OK ii think what you need to do now is try to get the phone to boot successfully into a stock rom for your region.
You mentioned in the first 2 or 3 posts that you did download from SamFirmware a stock rom.
It is probably a Odin flashable ROM
Is it a 3 file or 1 file?
Flash and then boot up the phone to be able to use it.
If successfull move on to the next step.
Click to expand...
Click to collapse
Unfortunately, it does not boot into stock ROM. It just loops.
I tried to do it over again. I used a different firmware: I9000XXJVU_I9000OXAJVU_OXA
So let's begin by retracing everything I did.
1) I essentially did this: http://www.androidegis.com/how-to/learn-how-to-install-xxjvu-firmware-on-galaxy-s-i9000/ (so it had the 4 files: pit, PDA, Code & CSC)
2) After I did that, I went into Odin and Put this as PDA "CF-Root-XX_OXA_JVU_2.3.6-v4.3-CWM3RFS" and clicked start
3) It then loaded but it keep looping. I had a feeling it didn't have a ROM installed. I erased data, cache and etc. Then I installed the Dark Knight 3 ROM. Install by external SD because I couldn't get the internal SD to work "Can't mount /emmc/" error.
4) I then reboot. I get the ROM loading screen. Then boom, stuck on Encryption Unsuccessful.
5) I put it back in recovery mode and repeat step 3 again.
6) I get the encryption error again.
Pretty much stuck at there.

so what you are saying is that no matter what firmware you flash it will boot loop?
I personally would not be trying a ICS ROM until you can boot a gingerbread rom successfully.
I have personally softbricked my phone once where i then was able to get into 3BR but was unable to boot due to a bad flash reflashing a gingerbread rom a couple of times with odin worked for me.
Try reflashing your JVU rom 2 times in a row.
I assume that you are able to get into 3BR if so what happens if you try to mount /system is there a error message?
When the phone is boot looping what is displayed on the screen?

Dorianking said:
Unfortunately, it does not boot into stock ROM. It just loops.
I tried to do it over again. I used a different firmware: I9000XXJVU_I9000OXAJVU_OXA
So let's begin by retracing everything I did.
1) I essentially did this: http://www.androidegis.com/how-to/learn-how-to-install-xxjvu-firmware-on-galaxy-s-i9000/ (so it had the 4 files: pit, PDA, Code & CSC)
2) After I did that, I went into Odin and Put this as PDA "CF-Root-XX_OXA_JVU_2.3.6-v4.3-CWM3RFS" and clicked start
3) It then loaded but it keep looping. I had a feeling it didn't have a ROM installed. I erased data, cache and etc. Then I installed the Dark Knight 3 ROM. Install by external SD because I couldn't get the internal SD to work "Can't mount /emmc/" error.
4) I then reboot. I get the ROM loading screen. Then boom, stuck on Encryption Unsuccessful.
5) I put it back in recovery mode and repeat step 3 again.
6) I get the encryption error again.
Pretty much stuck at there.
Click to expand...
Click to collapse
from what you are doing it seems like you aren't doing what we say. Sorry if this is not the case.
1. Follow steps from your link above.
2. Attempt to reboot. Most likely you will be stuck in boot.
3. Flash again steps as link above. This time do not use pit and make sure repartition is unchecked.
4. Now boot. This time you should boot into stock.
5. Once in stock set USB debugging on and connect phone to PC and copy ROM you want to flash to internal sd card .
6. Flash CF-root with Odin.
8. Restart phone in to recovery and flash ROM on sd card.
Sorry to repeat this but none of what you say mentions flashing stock twice once with and once without repartition checked. You need to do this right after each other.
Sent from my GT-P7500 using xda premium

So your suggestion is to keep doing JVU flashing until I can get it to work? Do I just follow that instruction and do the flash once with the PIT file (and repartition) and do it again without the PIT file? If it still doesn't boot, what then?
The phone boot looping. RIGHT when you turn on the phone. It has that Samsung Galaxy I9000 screen. It just has that, goes black for like 2-3 seconds then resets itself over and over again.
There is no issue with mount /system. I believe when I try to mount /emmc, there is an error. This is important because this is what lets me access the internal SD.

scubadude said:
from what you are doing it seems like you aren't doing what we say. Sorry if this is not the case.
1. Follow steps from your link above.
2. Attempt to reboot. Most likely you will be stuck in boot.
3. Flash again steps as link above. This time do not use pit and make sure repartition is unchecked.
4. Now boot. This time you should boot into stock.
5. Once in stock set USB debugging on and connect phone to PC and copy ROM you want to flash to internal sd card .
6. Flash CF-root with Odin.
8. Restart phone in to recovery and flash ROM on sd card.
Sorry to repeat this but none of what you say mentions flashing stock twice once with and once without repartition checked. You need to do this right after each other.
Sent from my GT-P7500 using xda premium
Click to expand...
Click to collapse
After step number 1, I get this in the Android system recover <3e>
Code:
Copying media file
E:failed to mount. /sdcard (File exists)
E:copy_dbdata_media:Can't mount /sdcard you storage not prepared yet. please use UI menu for format and reboot actions.
Media files copy failed.
# MANUAL MODE #
Appling Multi-CSC...
Installing Multi-CSC
Can't access to '/system/csc/BMC/system/'.
Successfully applied multi-CSC.
I proceed to step 2. It doesn't boot so I do the 3BR.
I do step number 3, but step number 4 doesn't happen; I tried what you just said and it won't boot into the stock. It just goes into Android system recovery <3e> and the copying media files fails (both times I flash it). Just an error, still can reboot system and etc but I don't think anything happens.
This error on the second flash is
Code:
E:failed to mount /sdcard (file exists)
E: copy_dbdata_media: Can't mount /sdcard your storage not prepared yet. Please use UI menu for format and reboot actions.
Media files copy failed
#MANUAL MODE#
-- Applying Mutli-CSC...
Installing Multi-CSC
Can't acces to '/system/csc/BMC/system/'
Successfully applied multi-CSC.
Click Reboot Now is <3e>. Nothing happens, it boots up. Shows the first Samsung Galaxy S screen, does nothing. About to boot stock ROM but doesn't. Loops it back to the SGS screen once more. Then it just shuts off and a picture of a battery shows up?

If you are flashing through Odin twice all three files 1st time with pit and repartition checked, second time without pit and repartition unchecked and still have issues then I would say problem may be with phone but I am new to this myself. Only commenting and given suggestions as I had similar issues which I resolved with steps I mentioned.
Options would be to download another stock ROM and do a checksum to ensure it is fine, download a different version of Odin (i use odin 1.85) and a new 512 pit file, reinstall the drivers for the phone, try it all on a different PC. Also make sure kies is not running when you do this (kill any background services.for kies) and try disable your antivirus on your PC. Also remove external as card and Sim.
If these suggestions don't help try search google for those errors you are getting. That's what I have done and managed to sort every issue so far.
Sent from my GT-P7500 using xda premium

Ok lots of reading in past posts here's what I would do and it works everytime. Google links to xxjvu firmware and and use those three files plus pit 512 repartition checkedand flash. Then to root your phone simply go to darky website. But before you do any of that tell me what rom you were on before you flashed new kernel and what exactly were you trying to accomplish out of your phone. ie.end result and who your service provider is. If you pm me I can walk you through it no problem.
Sent from my GT-I9000 using Tapatalk

It was 2.3.3 I believe before I did it.
My goal is to put a nice custom ROM (looking towards Dark Knight 3).
I have no idea what the specific darky rom I need.
Service provider was Virgin Canada.

Been thinking. Have you tried using heimdal. Try search for a tutorial that flashes a stock ROM with heimdal.
Sent from my GT-P7500 using xda premium

What did you have before the problems? Was it a lagfixed rom with ext4 partitions?
I've had strange problems when I tried to flash stuff with a lagfix, try to flash your stock base, and then flash a kernel that supports ext4. See if it boots up. If it does, disable lagfix and then change to whatever you want

[Q]Unable to flash Cyanogenmod from rooted I9000XXJW4

Hi,
I'm having a major issue with not being able to flash roms using clockworkmod for some strange reason.
I decided to move from MIUI rom because every time I gave it a chance when new versions came out, it constantly let me down with countless bugs and such. So, I've decided to go back to modified stock ROMs as they seem more reliable.
When I attempted to flash using clockworkmod (that comes with MIUI) it failed to apply the new (non-MIUI) ROM and forced it to go into a bootloop which knackered up going into recovery, so my only other option was to go into download mode and flash a stock ROM (I chose the latest, I9000XXJW4), root it, flash cyanogenmod and try again.
But unfortunately this did not work and now I'm stuck on the stock ROM.
I've taken a video of the exact moment it all goes wrong. Also, below is each step taken of the process.
youtube.com/watch?v=EmZAZ3DeL2U
1) Download Samsung Value Pack (I9000XXJW4) and CF-Root-XX_OXA_JW4-v4.4-CWM3RFS
2) Galaxy S rebooted to download mode
3) Used Odin3 1.85 to apply JW4_JW4_JW4.TAR file to the PDA section. Re-Partition is not checked.
4) Allowed the device to reboot to the home screen.
5) Powered off the device and booted back to download mode
6) Used Odin3 1.85 to apply CF-Root-XX_OXA_JW4-v4.4-CWM3RFS.TAR to the PDA section. Re-Partition is not checked.
7) Allowed the device to reboot to the home screen (The video begins now).
8) Launched the CWM application (with root permissions) and rebooted to Recovery.
9) Wipe data/factory reset selected and confirmed
10) Wipe Dalvik Cache selected and confirmed
11) Format /system selected and confirmed
12) Install zip from SD Card, Choose Zip from sdcard and update-cm-7.1.0-GalaxyS-signed.zip selected and confirmed.
13) Here is an extract from the log that follows before rebooting:
- Finding update package...
- Opening update package...
- Installing update...
- Checking state of BML/MTD...
14) Self-Rebooted
15) Boot-loop
Any help is greatly appreciated!
Thanks,
Andy

when it bootloops it does it cause it just flashed the kernel and its trying to run the stock rom on the cynogen kernel. so pull the battery, put it back in. reboot into recovery and flash the rom again. it should work the second time cause its using the cynogen mods version of cwm recovery. let it boot it will take a while. but that should work.
dont forget to hit thanks!

taz0697 said:
when it bootloops it does it cause it just flashed the kernel and its trying to run the stock rom on the cynogen kernel. so pull the battery, put it back in. reboot into recovery and flash the rom again. it should work the second time cause its using the cynogen mods version of cwm recovery. let it boot it will take a while. but that should work.
dont forget to hit thanks!
Click to expand...
Click to collapse
Genius!
Thank You!
Cannot believe the solution was staring at me the entire time!!