Captivate Replacment Question - Captivate Q&A, Help & Troubleshooting

I just had my captivate replaced due to the shutoff issue. The new phone does not have the standard sticker under the battery but rather a generic white sticker with little info.
This is straight frm the ATT store and does include the IMEI however it does not show the hardware version. I remember reading a few times there was something with the newer models in regards to flashing. Can any link me to the right post or give me an idea if there is anythign i neeed to be worried about.
Thanks

Check to see if you can do the three button method to get into recovery mode and also check that you can get into download mode using 2-button + usb cable. If you can do that you are in good shape to the best of my knowledge. I got two replacements (same time, one mine & one wife's) and did this check and everything has been going great. We have had zero shutdowns and great GPS with stock or most of the many ROMS I have ran since the "new' phones arrived.

Yea tried those first thing. Hope this phone works out the shutdown thing was evil.

Related

New P3600i sticks at splash screen

Bought it 5 days ago. When the battery went dead last night, I plugged it in to charge and switched it on .It did not go past the Windows Mobile splash screen. I took the battery out as well as the sim and memory cards, to no avail. I left it plugged in overnight and got the battery fully charged (battery indicator light is now green) and the network status green light would (at least sometimes) start flashing on boot, even though the phone would not completely boot up. I CAN get it into bootloader. What I want to know is, should I go to www.htc.com and download and install an official ROM from there, or should I leave all that alone and take it back to where I got it from before I screw it up? Additionally, the phone shows up as a Dopod D810 when registered on www.htc.com, and the radio and ROM versions appear to be lower/older than what came pre-installed in the phone. Advice anyone? I am fairly new and in the process of learning all this wonderful stuff you guys have to teach.
it seems like its already been fiddled with (correct me if i'm wrong people), i would visit the HTC club site and if you can upgrade using your serial number do that, as if you look in the trinity WIKI in "Trinity" forum (Not Trinity 6 forum, here) it states there is a different way to flash the p3600i as its setup different than the standard p3600.
This is exactly what happened to my phone when the battery died (after installing FInixNOver) Is there a problem with these ROMS, or something that happens when the phone dies!... My phone was also 'sticking/frozen/crashed' on the splash screen.
I just reflashed it with a new ROM after fully charging it again.
Thanks VISTAR. And WIZZKID - your phone works perfectly now after the flashing? And do you think it's because of the stuff you installed? BTW my ROM was an official HTC ROM. I actually got called out early this morning to do a flight to the island where I bought the phone (I am a commercial pilot flying Caribbean routes) and I packed it's backside back in the box and sent it to be exchanged. I don't have the new one yet, but I am beginning to wonder if I shouldn't try something else because of this problem of sticking at the splash screen - however I only have a choice of the Kaiser and the S730 at the moment. The P3600/P3600i is among my favourite WM phones of all times, but I don't wanna have to go thru this again. What do you guys think? By the way - I only just realized that I started this post in the wrong section, so please forgive me anyone whom is not pleased by that.
iF YOU HAVE THE CHANCE OF A KAISER I WOULD GO WITH THAT, ITS THE BEST OUT THERE AT THE MOMENT..
Yeah I know but I just don't like it the way I like the P3600i and some of the others. Besides I prefer no sliding hardware keyboard. Moving parts is an issue for me as I am very fussy about wear and tear/looseness. Thanks again for your help. I am gonna move over to WIZZKID's thread on this P3600/P3600i non-starting issue since I am in the wrong section of the forum. Thanks to all those who assisted...
Got a second P3600i and it did the same thing - a hard reset fixed the problem.

Is my USB port busted?

Tried connecting my kaiser to 2 different pc's and it won't get detected. The device will charge but activesync won't pick it up. Also its not listed in device manager! I tried disabling/renabling advanced network functionality as well has soft reset the device several times. I'm on the verge of hard reseting BUT when i put my device in bootloader mode it only says serial.. will not say USB as its supposed to
any help would be appreciated.. i'm on death v4 rom btw.
thanks in advance!
fone_fanatic said:
The device will charge but activesync won't pick it up.
Click to expand...
Click to collapse
Can you get an activesync connection via Bluetooth? When you inspect the extUSB connection can you see anything which looks wrong (such as a wire sticking out/in more than the others? What happened preceding this problem?
If you hard reset the device I don't see the relevance of the bootloader. It'll just restore the original image from where it's tucked away in the devices ROM. If it was working fine straight after you installed the ROM thats on it now and doesn't work after a hard restore then that points towards a hardware failure. If you have to go down the path of restoring to a different (original) ROM for returning purposes, there are ways of doing this with a microSD card - although I've not tried. I think the wiki would help there.
bluetooth activesync is working, i did a hard reset and nothing. Flashed to romeos via microsd and now its acting all strange.
After it completed the flash from microsd, i soft reset the device and it rebooted backinto bootloader.. i removed the microsd and soft reset several times and it kept going to bootloader. I attempted to hard reset as well and same thing, would go to bootloader. Removed the battery for a couple minutes and still same thing. Plugged it into USB with it off and it turn on by itself and go straight to bootloader. Unplugged the USB cable, took out the battery and put it back in, then plug the USB cable back in and this time the orange light came on as if charging and it finally booted up. The above has happened to me previously on my hermes but that was when the battery was extremely low, my battery level is currently at 97%!
now its booted into the freshly flashed rom and still same thing... charging but not being recognized by the PC... i've checked the usb port on the device and everything looks fine.
I'm lost at what to do now....
This might be a stupid reply but I had the same problem. My cable was busted so you could try another cable.
I am in the same situation here
Tried it with 3 different PCs with 3 different cables.
It's charging, Active sync pickes it up and trying to connect but fails to connect.
The only think I can come up with, I used new charger in the car. May be it killed the port
Is there any way to find out for sure?
i tried 2 cables with 2 different pcs... its only charging it and the computer won't detect the device at all. Nothing under usb in device manager.. even in bootloader, it only says serial not usb. I've downgraded to a shipped AT&T rom and Radio through the storage card but i still need to downgrade the SPL before i attempt to get a warranty exchange. IS that possible to do with through microsd yet?
I'm having the same issue. The usb port charges the phone fine with the USB cable, but teh computer does not detect the device. I also tried the headphones and they work fine as well. Help!
Update: I just tried a different usb cable, and now the computer recognizes the device, but as an unknown device.!!!!!
fone_fanatic said:
bluetooth activesync is working, i did a hard reset and nothing. Flashed to romeos via microsd and now its acting all strange.
After it completed the flash from microsd, i soft reset the device and it rebooted backinto bootloader.. i removed the microsd and soft reset several times and it kept going to bootloader. I attempted to hard reset as well and same thing, would go to bootloader. Removed the battery for a couple minutes and still same thing. Plugged it into USB with it off and it turn on by itself and go straight to bootloader. Unplugged the USB cable, took out the battery and put it back in, then plug the USB cable back in and this time the orange light came on as if charging and it finally booted up. The above has happened to me previously on my hermes but that was when the battery was extremely low, my battery level is currently at 97%!
now its booted into the freshly flashed rom and still same thing... charging but not being recognized by the PC... i've checked the usb port on the device and everything looks fine.
I'm lost at what to do now....
Click to expand...
Click to collapse
Have you tried these steps?
http://www.microsoft.com/windowsmobile/en-us/help/synchronize/activesync-usb.mspx
ajay6780 said:
Have you tried these steps?
http://www.microsoft.com/windowsmobile/en-us/help/synchronize/activesync-usb.mspx
Click to expand...
Click to collapse
Thanks for that suggestion but still no dice
The computer isn't detecting the device at all! Usually when a usb device is plugged in you can go to device manager and look under USB and see it there, but its not showing up. I've scanned for hardware changes several times and nothing.
I've now tried on 3 different computers (2 pc's and 1 mac) with 2 different USB-MiniUSB cables and nothing!!
i guess i'll just go to the at&t device support center tomorrow and hope they'll replace it on the spot and notice that i've changed the SPL...
can i ask for the people that are having this problem to do the following.
With your device unplugged from the PC open device manager. (Right click My Computer -> Properties -> Hardware (3rd tab) -> Device manager) Then expand the last tab (Universal Serial Bus Controller) and plug in your device.. if it doesn't show up then click actions -> scan for hardware changes..
I just want to make sure if your computer is detecting your device or not..
just an update with my situation. i went into the att device service center today and told them my problem... the guy behind the counter had no clue what he was doing. he just looked at it like a monkey for minutes then swapped it out for a new one. no questions asked even though it was hard spl'd, cid unlocked, and sim unlocked.
but now this device's vibration is really weak and i lost my invsishield protection on the front (kept the battery cover and my ppctechs scren protector)
Busted? or just won't work
Hi all,
I have been coming to these forums for a little while and only posted a couple of times. I felt this was important. I was having the same problem. Tried the cables, resets, ROM changes the works. I have had my at&t tilt htc 8925 for 36 days when I reported the problem to them. But it actually started about 10 days before. At&t tech support was very rude and accusatory when it came to them "helping" me. I, like probably all owners of a phone like this treat it like gold. It is very important to me. So when I contacted tech support and was told it was probably abuse or I had "buyers remorse" (I don't want to return the phone I just want it fixed!?)
The best they can do and they do not budge on this is for me to return the phone for an exchange. BUT, and this is a BIG AT&T but, the phone they exchange it with is refurbished. Something someone has returned. I do not want a phone that has been returned. I want mine fixed. "This is my phone, there are many like it but this one is mine" Know what I mean? When I bought the phone the guarantee was "we'll just replace it with a new phone" and I like 1000's of others did not ask if that "new phone" was refurbished. It is. Now advocates will tell you as they did me, refurbished is actually BETTER than new. Huh? Then why aren't all phones sold refurbished ones? And if they are so great, take mine back, give me one of those "crappy" new phones and give mine to someone who wants a sweet refurb. I am outraged by the whole mess.
I have searched forums and complaint sites. The bad usb port problem is NOT an isolated incident. There are a lot of people with the same "it charges but won't sync" problem. This is a known problem they refuse to address. Their stand, send in for refurb.
Personally I would like to see a recall fix class action against at&t. It can be fixed but they just don't want too. I thought I would be relatively safe buying for a huge company. They spend millions on advertising to simply leave their customers twisting in the wind after 30 days. Very bad business.
That's the rant. So I decided that if the warranty was useless anyway I'd take a shot at it myself before sending out for repair myself. There is a place in California PPC Tech http://www.pocketpctechs.com/main.asp?area=home that will fix the usb for $79 and ship it back to you in a few days. They seem to be reputable and a lot of people are opting to fix this problem themselves.
How did I fix mine? by altering the mini usb end of the sync cable. I tried other cables and connectors but I think it has something to do with the contact points. The only way mine would work was if I plugged it in, wiggled it slowly and with a little bit of pressure at times, around until the screen brightens. That means it has made a connection, then don't move. Hold very still. It took both my hands. Wait for what seems like 2 mins and it would start to sync. Based on this. my repair (before I send it to California for repair, which I may end up doing anyway) is make sure the plug on the phone is straight and not damaged. If you can get the phone to sync this way you may be able to crimp the mini end of the usb very very slightly to make the connection you are manually doing by wiggling it around. It took a lot of small tweaking but it now syncs about 29 out of 30 times. That's about as good as it gets.
So good luck to us all. If you can't get it to work yourself send it out west to PPC Tech. In this economy the phone companies like at&t better start getting their customer service back on track before they have no customers to service, It has happened to the biggest before. Wake up AT&T! The days of the business model of massive turnover and new signups is coming to an end as people tighten their belts. Treating current and future users poorly is a sure fire way to put yourself out of business.
here is my gift to you all..
http://forum.xda-developers.com/showthread.php?t=362679
read this post and check EVERY SINGLE LINK in the first post...i had this issue and i ended bending my usb plug every which way until finally i broke the plastic seperator off and in turn smashing the second pin from the left on the top off (the one in charge of activesync) over and over until it broke...i didnt really care i could still flash by sd but then i smashed the + power pin and so i was on the phone with att for many many hours explaining to them that its a known issue to users but not to the company and they finally sent me a replacement..i should have just searched my butt off before trying to deal with a problem/fox it myself (yes i dissasembled it and soldered the pin back on and it broke off multiple times causing me to dissasemble it many many times and smashing it again and i ended up getting alcohol on the water damage void pad which i replaced) learn from me...if you ever have ANY problems that are significant..dont try fixing JUST GET A REPLACEMENT...who cares if its a refurb..if the refurb sucks then send it back until they send you a new kit...after 5 returns you get a new kit soo just keep sendin back them refurbs until your happy
oh and to make it easy on yourself because if you tell att you have a usb problem its NOT covered under warranty and will take you many many hours like me to convince them otherwise (which someone eventually will understand because certain people ARE familiar with this problem at ATT it just depends who you get and how many times youve been elevated in support)..what you need to do is IF YOU CAN return your spl back to stock (if you manage to get a long enough connection with activesync) but if not dont worry too much att doesnt really check spl just that you have the shipped rom on there so load the shipped rom (found on here) on your sd and flash back and just make up some excuse that it isnt working right and youl get a replacement or if you can get the spl revrted jus throw your device in bootloader by a failed flash (pull the usb out during flash) and say its stuck in the funny colored screen lol
jaysjob, i've been dealing with ppctechs for a long time (probably since '03-'04) they're very reputable and highly recommended. They actually got the contract to be the authorized repair center for I-Mate about a year ago.
But why would you pay $79 for something where u can get a complete replacement? Yah it might be a refurb but my device that i turned in was all scratched up from drops.. the images on the start, ie, and messaging buttons by the d-pad had scratched off.. and now the device i got looks brand new (i actually think it is a new one but i never asked if it was a refurb or not)
pazookie, what your saying is true.. always take advantage of the warranty if you have it. If you dont and you want to repair it yourself, know what your doing! I'm very handy and have done many lcd replacements and other various repairs on cellphones (nokias, HTCs, sony ericsson, samsung, motorola, u name it!)
My little brother has the n82 and he bought the black case, I told him to wait for me and i'd help him do it but he got impatient and he thought it was gonna be a simple swap. He ended up breaking his LCD doing it which set him back $80!
anyways i'm happy now with a new device but i'm gonna go back tomorrow and get it replaced again because the vibrate is extremely weak!
fone_fanatic said:
jaysjob, i've been dealing with ppctechs for a long time (probably since '03-'04) they're very reputable and highly recommended. They actually got the contract to be the authorized repair center for I-Mate about a year ago.
But why would you pay $79 for something where u can get a complete replacement? Yah it might be a refurb but my device that i turned in was all scratched up from drops.. the images on the start, ie, and messaging buttons by the d-pad had scratched off.. and now the device i got looks brand new (i actually think it is a new one but i never asked if it was a refurb or not)
pazookie, what your saying is true.. always take advantage of the warranty if you have it. If you dont and you want to repair it yourself, know what your doing! I'm very handy and have done many lcd replacements and other various repairs on cellphones (Niki's, HTCs, sony ericsson, samsung, motorola, u name it!)
My little brother has the n82 and he bought the black case, I told him to wait for me and i'd help him do it but he got impatient and he thought it was gonna be a simple swap. He ended up breaking his LCD doing it which set him back $80!
anyways i'm happy now with a new device but i'm gonna go back tomorrow and get it replaced again because the vibrate is extremely weak!
Click to expand...
Click to collapse
Hi fone
Thanks for the reply.
Yes, I agree with you. If the phone has something else that is messed up like you were saying a scratched screen or buttons. It's just that I am as careful as I can be to keep the phone in nice condition just to send it back for maybe one that someone didn't take the same care of.
Mine works good now. I think it has something to do with when I crimped the cable end. It make a tighter fit. I think that may be the key to mine and others problems. For sure it is becoming more and more clear that there is a design flaw whether att wants to acknowledge it or not.
Thanks for your input about PPC too. If I do end up having to fix it that's probably the way I'll go if that is still the only thing wrong. Otherwise it's in for the warranty as you suggested. I KNOW I'm not that smart.
Im having this same issue and it is definately not a cable problem.
tayloryork said:
Im having this same issue and it is definately not a cable problem.
Click to expand...
Click to collapse
if u think its a hardware problem then take it to a service center. The guys there just follow step by step guides on how to diagnose phone issues. For me he saw a crack in the usb jack on my device and just replaced it. If you send it in to HTC i think theres a higher risk of them figuring outu the device is hard spl'd and wont honor your warranty.
tayloryork said:
Im having this same issue and it is definately not a cable problem.
Click to expand...
Click to collapse
taylor, I'm not saying it is a cable problem. I am saying it is a hardware port problem. I "fixed" mine, probably temporarily, by crimping my usb cord so that it holds more firmly in the port. I did say if you have the same problem and you use the same test I did ie: move it slightly, Gently, not like others I have heard stories of where they ram it from side to side until it snaps off, that you might be able to do what I did. I thought others with the same problem might be able to use this workaround until at&t figures out it is not an isolated incident with thousands of people having the same problem thats all. Hope this helps.
jj
I had a similar problem. Phone would charge fine, but windows didnt even recognise anything was plugged in. Interestingly the bootloader changed to USB when the cable was connected, and Serial when unplugged.
As it turns out (thanks Flying Kiwi for suggesting the obvious I had overlooked) the middle top pin was recessed too much into the plastic guide, so I stabbed it a bit with a scapel and all is well.
So it seems that the Serial/USB section of the bootloader cant even be trusted.

Dimaond Gets Hot and Screen Alignment Goes Out

I have done a reasonable amount of searching on this and have not found anything specific to my problem so figured I should post a question.
I have an issue with my Dimaond when it gets hot generally either using Wifi or Phone Data connection that the screen goes out. Basically everything goes to the left side of the phone so if you hit the Task Icon in the top right corner you get the Start Menu. Phone is basically useless at this point and you have to wait for it to cool down. Has happened since day one and is generally worse when using it when charging. I was watching Utube on it the other night 5min video while on AC charge and it went out. I am running Dutty 2.5 Rom and 25.07 radio have tryed 25.08 and 25.05 no difference was happening when the phone had orginal HTC ROM as well. Also will happen on a long call if the screen is on.
Basically feel issue is hardware related and maybe faulty screen still under warrenty so wanted to know peoples opinion on weather I should send back. Problem is will take a couple of weeks and I don't really wnat to wait that long if I can help it. Also assume it would be best to flash standard ROM back, should I do anything with HARDSPL eg should this be changed back as well if I send it back.
And before anyone says it I have tryed searching this topic and have found lots about HOT dimaonds but nothing related to screen going out at the same time :-(
Thanks
I had this issue in my JasJam (Hermes) whre the screen would simply go white after a while of use and I would have to leave it for a while for it to work again.
Unfortunately it sa hardware issue and you should claim a warranty repair on it
I can't see how this could be a software problem so I figured it must be the screen eg hardware related. Would be nice to know if anyone has had the same issue with a dimaond... Seems we may be spending some time apart, just hope it doesn't take long to fix..
I've had the same issue
http://forum.xda-developers.com/showthread.php?t=428976
My first device had been replaced recently (i.e. today) by my network provider (o2) and the new device seems to work without any problems now even if it's "hot".
(i.e. default screen adjustment + creating heat by activating the phone, wlan, bt + recharging it)
I sent an email to HTC regarding the fault and they said it would have to go back for a warrenty repair. I brought it through a resellar so has to go back to HK from NZ so will be away three weeks uurggghhh... Just seems odd I don't have any physical damage on the screen but hte problem has been around since day one as I remember having the problem the first day I got it. Juyst seems to be getting worse and is easily reproduced by usiung utube over wifi gets hot and it is all over. Just wondering if I should put an offical ROM from HTC back on the device before I send it back as I currenty am running Dutty ROM, what do you think....
i put the original rom back on and they still found out the the rom had been flashed, and would not repair on warranty
yep, i also asked about this problem
http://forum.xda-developers.com/showthread.php?t=438733
there are some youtube video's of how the phone behaves
my phone seems to do it less frequently since stopping using panosha's rom
im using alpha zero 7 at the moment..
i've also noticed that it isnt necessarily a heat issue, my phone does it completely at random
yesterday i found though, that when the phone did the alignment issue, i gave it a good shake.. and hey.. its all aligned again?!
maybe it was just a fluke, it hasnt freaked out since..
holding thumbs
Hey,
I also have the same screen problem, but my Alignment goes to right.
If I press on the left side, a press on the right side is recognized.
Good to know that Im not the only one with this problem.
greets doena
I got my phone back a week ago replaced the screen has been away for over two months, complete disaster, anyway all sorted now and I have not had the problem since....
I had this exact same issue (out of the box).
It was a hardware fault and I exchanged it for another one.
Haven't had any problems since.
Minus-1 said:
I had this exact same issue (out of the box).
It was a hardware fault and I exchanged it for another one.
Haven't had any problems since.
Click to expand...
Click to collapse
Hardware's fault ? Most likely not. I will give u an example of why I think it was software related. My device ran hot as well but I simply switched roms and now it's the complete opposite. Your most recent device most likely come with a different Rom in the phone.

HELP?!?!? Returning to stock without a screen?

Hi all,
having only had my phone for around 2 weeks tonight the inner screen of my phone has decided to crack whilst sat on the side doing nothing (Yes, I know, likely story but in my case it is true). Luckily Orange have been very good and are sending out a replacement handset tomorrow as it is still under warranty.
All good I thought, but I am now worried that I have to also send the handset back. It is currently running Darkys firmware and wondered if this is likely to be an issue. Also, the phone is configured for my work email and would like to remove this info before hand.
Any suggestions on how I quicky (and without a screen) return a phone to stock would be very much appreciated!
Cheers,
Michael
It is currently running Darkys firmware and wondered if this is likely to be an issue
YES its broken the warranty depends upon how close they inspect the phone etc .
Post on a similar topic within the last two months re no screen
Normal method of returning to stock is .
http://forum.xda-developers.com/showthread.php?t=818556
jje
Pull the Battery and reinsert it.
Get into the Download Mode.
Flash it with a Custom Kernel.
Unplug the USB during the Flashing Procedure
You will end up with a bricked phone which will force Orange to reinstall the firmware.
And as JJEgan said, it all depends upon how they inspect the phone. If they agree for a replacement, then its well and good. Orelse, you can try my method
by your post I gather you don't see anything on the screen. If this is true, why worry. Orange techs will not be able to see what firmware you are running if the screen does not work.
They are not going to install a new screen to see what stuff you have on your phone.
I bought my phone off of the online classifieds, so I thought there was no warranty.
I was having a problem with the USB port not working properly as I got some mushroom soup (Don't ask) in the port. I figured since I do not have any warranty I will take the phone apart and see what I can do. I cut the top of the metal shield off with a Dremel tool and cleaned the USB port out really well. It did work after this, but about two weeks later my internal SC card died.
I brought the phone into Samsung service center and to my disbelief, they replaced the phone, no questions asked. I guess they didn't even open the phone.
I wouldn't worry.
Ian

QHSUSB_DLOAD, Dead Phone, Stock OS

My GFs HTC One, for the second time now (two different phones), has gone dead out of nowhere.
The first time she plugged it in and went to bed. All was well with it when it was plugged in. Woke up and nothing worked. No charging lights, nothing. Sent it in for warranty repair and T-Mobile/HTC said that the LCD screen was broke and that it was due to user damage (basically trying to say the phone was dropped, which it wasn't). They sent out a new phone, we sent back the broken one. A week later they charged our bill for the repairs and I had to call in 3 times in order to get them to finally waive those charges.
Now, a few months later, this new phone does the same thing. In the middle of using it, while it had plenty of battery, the screen went black. Same exact thing, would not power back on. Now we are in the process of waiting for the next phone to be shipped so we can ship this one back. And I'm fairly certain that they're going to try and use the same excuse again.
The only response that we get from the phone is when it is plugged into a computer and it asks to install the QHSUSB_DLOAD driver (which does nothing upon trying to install). After searching these forums, and Google, I noticed that everyone with this exact problem was trying to install a custom ROM. That is not the case with us. The OS on the phone's were never altered. The phone's were never unlocked. Nothing like that at all.
I don't really have a question that I'm asking here. From what I've read, it looks like the phone is basically bricked and there's nothing that can fix it. I just wanted to make this post so others know that this can happen to non-rooted phones too.
I'll follow up here once T-Moble/HTC give me the outcome of this second phone.
Exact same problem here.
Edge611 said:
Exact same problem here.
Click to expand...
Click to collapse
QHSUSB_DLOAD = hard brick, needs motherboard to be replaced
Had same thing with HTC Sensation. Need to replase the main memory chip where OS stored.
Time for a new girlfriend, not a new phone.

Categories

Resources