Hi guys,
Hoping someone can help me.
I attempted to flash my ROM with Darkys, but my Galaxy S didn't play ball and stopped booting.
So I followed the usual steps to get it back via odin.
Procedure:
1.Open ODIN. (And close Kies, if you have it open. It is important to have ODIN open BEFORE connection the phone via USB!)
2.Select the PDA/Modem/CSC/.PIT files in Odin. (.PIT and PDA are required. CSC and Modem are HIGHLY recommended. They may be necessary depending on the PDA! Try flashing all three BEFORE reporting bugs, if you only used one initially!)
3.Check the "Re-Partition" checkbox.
4.Turn the phone into the download mode by pressing and holding VolumeDown+Home+Power.
5.Connect your phone with your computer and wait until the drivers are installed.
6.When the drivers are installed, click Start.
7.The phone will be flashed and once it’s finished, it will boot up. (Do NOT disconnect the usb-cable, remove the battery or otherwise interrupt this process!)
8.You have successfully flashed your phone.
Now, It worked yesterday and all was good, but as you know Eclair is powerfully S*%t So I tried reflashing darkys from the Clockworldmod, and this also killed the phone preventing it from booting.
After this I could not access recovery mode.. only Download mode.
Rinse and repeat the steps above... Sadly now once my phone goes to reboot after reflash in Odin, it freezes on the white rotating circles.. and doesn't progress. as mentioned above, I can only get into Download mode.
My Galaxy is a GT-i9000 (Australian Optus).
Can someone please help?? I've looked around but can't find a fix.
If you can help me out that would be Awesome..
Since you are using eclair, I would suggest first upgrading to a stock froyo (there is a froyo upgrade guide in general) and if that works try darkyys rom.
Sent from my GT-I9000 using Tapatalk
Flashed xx rom twice and it broke your phone . Lesson learnt ???.
Go to Rom Kitchen and download a rom to your build and flash .
http://romkitchen.org/sgs/?s=home
http://forum.xda-developers.com/showthread.php?t=817703
First you may need to flash a clean setup
Block 2 Odin method .
http://forum.xda-developers.com/showthread.php?t=818556
jje
Related
So here't the full background, it's not long, please read:
http://www.darkyrom.com/community/i...-bricked-my-sgs-wonder-what-i-did-wrong.2032/
Long story short, it looks like I bricked my SGS when trying to flash with Odin, even though I followed the tutorial very closely. When I power up the phone, it just gives me the image with phone, exclamation mark and PC on it. It does, however, go into download mode when powered up with VolDown and center button.
How do I save it? Do I need the JIG (God, please say no! )
Have you tried reflashing with odin.
Jig is only needed when you cant get into download mode.
Also i just looked inside the darky rom topic.
Have you flashed the jvk rom first with the bootloaders?
Edit: as said below. If you gonna reflash, flash a stock rom. Not the darky rom. First priority is to make your phone work.
Sent from my GT-I9000 using XDA Premium App
Yeah, you have download mode.
Now, fire up Odin and load a few rom files into it, connect the phone and see if the PC still recognises it. (Do not flash, Just a test)
If so...
Flash a stock rom.
Somehow, I was able to flash it with Odin in Download Mode this time. Phew! I read somewhere that the flash might fail if You're using wrong USB port. At first I connected my phone to a eSATA/USB combo port, and for the second time (after brick) I tried a normal USB 2.0 port in my laptop. Maybe that's what made the difference, I have no idea.
Anyway, I'm running stock Samsung 2.3 rom and am trying to install Darky's 10.0 RC3 on it - I am running into some problems, but thankfully they're much less serious than the brick that I was able to fix.
Thanks for Your help!
I ran into similar problems last week. A rom wouldn't flash, so I gave it an hour and it proceeded nowhere. Had to pull the plug on it.
Sometimes it just takes a few times plugging and unplugging repeatedly until it just happens to get detected by Windows. Maybe just a bit of luck too
Congrats on your recovery.
Just wondering which stock 2.3 rom did you use and which Odin setting you used to get your phone up and working again.
Here is my post / problem, seems similar to yours
http://forum.xda-developers.com/showthread.php?t=1020223
Thanks
I had the same issue like warnec on my first darkyy flash, finally everything went fine...don't worry!
just try to reflash with odin (maybe going for a stock version first is a good idea), be sure to do everything as mentioned in the guides out there. and be sure your computer works stable, maybe you want to quit some tasks in the background (however it should work even without but something crashed my odin once...)
Reflash with Odin to make your phone work again. I suggest using a stock 2.2.1/2.3.3 ROM. It is important that it consists of the 512.pit file, a PDA file, a Phone file and a CSC file. The ROM must have bootloaders included!
Now, disconnect your phone and turn it off.
Start Odin and load all the files. Tick 'Repartition'.
Start your phone in Download Mode by pressing Vol-Down, Home and Power.
Connect it to your PC and wait for Odin to say 'Added!'.
Now hit Start, wait 2-3 minutes until it is done and your phone should succesfully reboot!
Sent from my GT-I9000 using XDA Premium App
Thanks I tried this and my phone just keeps flashing i9000m screen, then blank and then back to the i9000m screen. Looks like the phone is unusable.
chriszak said:
Thanks I tried this and my phone just keeps flashing i9000m screen, then blank and then back to the i9000m screen. Looks like the phone is unusable.
Click to expand...
Click to collapse
does not sound very good...could you solve your problem yet?
Had to take the phone into Bell. Waiting on return of it and currently using a loaner HTC Desire Z from Bell.
Hi team!
Im new to this, may i ask..
Am i able to go from stock 2.1 straight to 2.3.3 by following this guide....
http://www.theandroidsoul.com/how-to-install-xxjvo-android-2-3-3-gingerbread-rom-on-your-galaxy-s/
Or will i encounter problems? do i need to go to 2.2 first?
Has anyone got the skills to give me some answers? if so thanks!
I didn't look at that guide in particular, it's like when someone does your homework for you... but it is possible to go straight to 2.3.. If your worried just go to 2.2 first...
that is all
Yeah, sure! With Odin, you can goo from any version to any version back and forth - a lot of people even use stock 2.1 to get a clean install before flashing something new, so don't worry. Just use a stock JVO version with bootloaders (there should be "Sbl" in the name of the PDA file). I alway flash stock ROMs with pit file and checked repartition - just 1) get in Odin and mount PDA (with bootloaders), Phone and CSC,also mount the pit file and check repartition, 2) turn off you phone and after that get in Download mode (Volume up+menu button+Power button), 3) connect the phone to your pc and hit start button in odin
Do not forget to take out sim card and memory card before flashing
[email protected]
To TS:-
I just brought Galaxy S with 2.2 Froyo , try to read in XDA forum and it help me a lot , you may refer to this thread http://forum.xda-developers.com/showthread.php?t=846913 download stock firmware 2.3.3
Instrcution on ODin1.3
1.take out all the sim card n memory card , turn off your phone and had USB cable on you pc/laptop without the KIES program running as well.
2.Double click to extract I9000XXJVO<--Example
3.Open ODIN. (And close Kies, if you have it open. It is important to have ODIN open BEFORE connection the phone via USB!)
4.Select the PDA,pit,Modem,CSC file in Odin.
5.Turn the phone into the download mode by pressing and holding VolumeDown+Home+Power.
6.Connect your phone with your computer and wait until the drivers are installed.
7.When the drivers are installed, click Start.
8.The phone will be flashed and once it’s finished, it will boot up. (Do NOT disconnect the usb-cable, remove the battery or otherwise interrupt this process!)
9.You have successfully flashed your phone.
hope this helps
Thanks guys, gona flash darks JVH rom (Ficeto_Deodexed_JVH_I9000_ODIN.zip)
as a base rom...
then flash Darkys 10.1
I was on Darkys 10.1 EE
I made sure voodoolagfix is off. I reset the phone to factory.
I wanted to move to the latest MIUI so I begun by flashing to EZrom by following these instructions.
http://www.theandroidsoul.com/ezbase-ezrom-for-android-2-2-install-revert-back/
I download all files proplery (using flashget)
selected the files using instructions.
Hit start, and nothing happening. Been like this for 15 min.
Uploaded with ImageShack.us
Should I turn of teh phone and try again or, while I am in download more try reflash 10.1 so as to not brick the phone?
EDIT: FFS phone is bricked. It is displaying the Phone ! Computer logo
sigh..now what?
Remove and reinsert your battery after some time. Don't turn your phone on. Directly use the 3 button combo to enter download mode. Connect USB cable. Flash new firmware using ODIN. Avoid EZOdin.
Did that, GOt back to Darkys again.
Do how do I flash a froyo 2.2 Base without EzOdin
I meant avoid EZOdin, use regular ODIN. On the safe side, use the newer ODIN3 1.82 or the trusty old ODIN3 1.31
Hi,
could anyone help!
my device is galaxy ace s5830i
i have already rooted my device and used CW Recovery and taken a copy of my original system .oki
i wanted to set up a custom rom i restarted and reset and deleted the cash then installed the rom.
i think it was Retribution beta
then i wanted to update to that custom rom (MindCR ICS)
all i did i restarted my phone of course went into R mode and reset and deleted the cash then installed that next custom rom .
after installing completed when i rebooted it only gave me (samsung galaxy ace s5830i) logo and doesn't open the system when i restart it doesn't go into recovery or download mode it only gives me again the same logo.
even when i press long power button it shuts down and opens automatically.
is there any help knowing that i have already taken a copy of my system.
dana25 said:
After installing completed when i rebooted it only gave me (samsung galaxy ace s5830i) logo and doesn't open the system when i restart it doesn't go into recovery or download mode it only gives me again the same logo.
even when i press long power button it shuts down and opens automatically.
is there any help knowing that i have already taken a copy of my system.
Click to expand...
Click to collapse
I think you have a hard brick.....
Maybe JIG / JTAG can help.
Sent from my GT-S5830i using xda premium
RubenStauttener said:
I think you have a hard brick.....
Maybe JIG / JTAG can help.
Sent from my GT-S5830i using xda premium
Click to expand...
Click to collapse
would you provide me with that or tell me how?
dana25 said:
Hi,
could anyone help!
my device is galaxy ace s5830i
i have already rooted my device and used CW Recovery and taken a copy of my original system .oki
i wanted to set up a custom rom i restarted and reset and deleted the cash then installed the rom.
i think it was Retribution beta
then i wanted to update to that custom rom (MindCR ICS)
all i did i restarted my phone of course went into R mode and reset and deleted the cash then installed that next custom rom .
after installing completed when i rebooted it only gave me (samsung galaxy ace s5830i) logo and doesn't open the system when i restart it doesn't go into recovery or download mode it only gives me again the same logo.
even when i press long power button it shuts down and opens automatically.
is there any help knowing that i have already taken a copy of my system.
Click to expand...
Click to collapse
I have this problem before and i managed to use ODIN3 v1.83 (can use Odin3 v3.07) to detect my phone and flash a stock rom onto the device. I followed the advice given on this excellent thread by Supermini.
http://forum.xda-developers.com/showthread.php?t=1071970
As mentioned on his thread make sure you have the latest stock firmware from the sammobile site or by using Check Fus Downloader as per the guide in Rafael thread http://forum.xda-developers.com/showthread.php?t=1551156, a working samsung USB driver to detect your mobile on your PC and a copy of ODIN3 v1.83 (or v1.84, v1.87, v3.07 run ODIN in administrator mode if using in windows). Ultimately if this this fails you could always try a USB jig which can be purchased from ebay, etc. to get the phone into download mode.
Good luck and if this helps make sure you send a thank you to Supermini.
Viprdxd said:
I have this problem before and i managed to use ODIN3 v1.83 (can use Odin3 v3.07) to detect my phone and flash a stock rom onto the device. I followed the advice given on this excellent thread by Supermini.
http://forum.xda-developers.com/showthread.php?t=1071970
As mentioned on his thread make sure you have the latest stock firmware from the sammobile site or by using Check Fus Downloader as per the guide in Rafael thread http://forum.xda-developers.com/showthread.php?t=1551156, a working samsung USB driver to detect your mobile on your PC and a copy of ODIN3 v1.83 (or v1.84, v1.87, v3.07 run ODIN in administrator mode if using in windows). Ultimately if this this fails you could always try a USB jig which can be purchased from ebay, etc. to get the phone into download mode.
Good luck and if this helps make sure you send a thank you to Supermini.
Click to expand...
Click to collapse
thanks and sorry for late but as i told you i cant go into rev or download mode i tried to use odin 1.8 and the latest version but it doesn't recognize my phone shall i lose hope!
bro i think u most probably bricked ur phone but dont worry try opening download mode. then using the odin u install ur stock rom. Then u can access ur r mode. but try to read the entire procedure..of flashing the rom.
dana25 said:
thanks and sorry for late but as i told you i cant go into rev or download mode i tried to use odin 1.8 and the latest version but it doesn't recognize my phone shall i lose hope!
Click to expand...
Click to collapse
So . . . last thing to rescue your phone is buy on e-bay or in other place JIG if it isn't help you then try in phone service and say you tried install new ROM with Kies and your phone is brick (maybe it'll work).
Say to Service Centre Representatives that you kept your at charging last night
And when you woke up
It was not booting up
Pretend as if you dunno anything about root or ROM
They fixed my bricked phone
I am not sure if I am breaking any forum rule by telling this
Hey bro sorry for the late reply also, please before you do anything else try following my instructions.
1) download Odin v3.07
2) source the stock firmware you want to flash from sammobile.
3) make sure you have the Samsung mobile driver.
4) open and run Odin as administrator and load the single file in the PDA and highlight the tick box.
5) shut the phone down and take out your Sim card.
6) put the mobile into download mode as normal (press both up/down vol keys +power)
7) connect the phone to the PC and check in Odin to make sure its com port is detected.
8) then flash through Odin as normal.
I understand what your saying about no download screen appearing, I have found through experience that custom kernels can cause no download screen to appear. Normally with stock kernel this is not a problem but with custom kernels sometimes all you get is a black screen. Ignore this and just make sure that Odin is detecting the phone and try to flash, chances are it will flash the stock ROM and kernel. If you get the setup connection error in Odin and the fail 0\1 just try another USB port on your PC and keep persevering.
Please keep us updated so we can help you if you need it.
Sent from my Nexus 7 using xda app-developers app
Why will it be hardbricked if the custom roms are based on s5830i stock roms?
But it is probable that we did I not flash the rom properly as per procedure..so is there a chance that it be bricked? Else the rom may have some problem... just telling the probability
Sent from my GT-S5830i using xda premium
Help me .
help me on fixing my ace s5830i , my problem is after flashing it with RazoDroiD my phone seems to be ok , i decided to change my firmware by a stockrom using Odin mode or the Volume Up+Down+On off it stays on blank screen . Can you help me on fixing this ? and what do you call this problem .
Try following my instructions.
1) download Odin v3.07
2) source the stock firmware you want to flash from sammobile.
3) make sure you have the Samsung mobile driver.
4) open and run Odin as administrator and load the single file in the PDA and highlight the tick box.
5) shut the phone down and take out your Sim card.
6) put the mobile into download mode as normal (press both up/down vol keys +power)
7) connect the phone to the PC and check in Odin to make sure its com port is detected.
8) then flash through Odin as normal.
I understand what your saying about no download screen appearing, I have found through experience that custom kernels can cause no download screen to appear. Normally with stock kernel this is not a problem but with custom kernels sometimes all you get is a black screen. Ignore this and just make sure that Odin is detecting the phone and try to flash, chances are it will flash the stock ROM and kernel. If you get the setup connection error in Odin and the fail 0\1 just try another USB port on your PC and keep persevering.
Follow this and don't worry about black screen just make sure Odin detects your PC com port.
Sent from my Nexus 7 using xda app-developers app
Hi,
I have Samsung Galaxy S I9000 running Ginger Bread.
I wanted to upgrade my phone to Ice Cream Sandwitch or Jelly Beans. In order to do it, I started with below steps to root my mobile.
1. Installed latest Clockwise Mode application into my phone.
2. Installed Odin3 v1.7 in my laptop.
3. Downloaded CF-Root-XX_XEU_JPY-v1.3-BusyBox-1.17.1.tar on my laptop.
4. Started Odin first.
5. Disconnected mobile and started in download mode with Volume Down + Home Button + Power Key.
5. After starting the download mode, connected mobile to laptop using the USB.
6. Keep all the default values in Odin3 i.e. Re-Partition option unchecked, Auto Reboot and F-Reset Time option enabled. Selected tar file CF-Root-XX_XEU_JPY-v1.3-BusyBox-1.17.1.tar in PDA option.
7. Connected mobile and it detected ID Comm [Highlighted in Yellow].
8. Finally click on Start button.
After starting the process was completed and Yellow color changed to Green one, phone was auto reboot.
But after reboot it is just stuck on start of screen and not going ahead. I wait for 2 hours but still not working.
Could you please help me how I can solve this issue now?
Did you try to pull battery out and restart the phone again?
Do you still can go in CWM with 3 button combo again?
If yes then try to flash a ICS or JB kernel (depending on what ROM you finally want to have on your phone) via CWM and then go in advanced and restart recovery (if available), otherwise just try to flash the rom.zip on top.
If CWM is not possible, the go in download mode an falsh a tar version of kernel via ODIN.
Here are different semaphore kernels for each android version:
http://78.46.194.137/downloads/gt-i9000-ics
http://www.semaphore.gr/downloads/gt-i9000-jb
For ics it should work after 1. flash, but for JB you have to flash it 2 or even 3 times, if after restart phone does not boot. Then battery out again, start in recovery and flash zip again.
Good luck and good success .
I think, at this position, installing a new gingerbread stock ROM will be preferable. Try installing XXJVU. Then root with cwm and install any slim bean version in case you are interested to use jelly bean.
Sent from my GT-I9000 using xda app-developers app
Sure that will be the best way....but my suggestions do not take much time, so why not give them a try .
But if its not going, then a restock is the best you are right:
What I always do for restock is using slappys rescue kit.
Unzip it and flash the Rom via Odin. There is everything, also a txt file with a guide included.
http://forum.xda-developers.com/showpost.php?p=29114573&postcount=2
If you want to have slim rom then its recommended to flash CM9 first or flash a modem afterwards via cvm, because slim does not have a modem included.
And/Or just follow the installation guides/recommendations from the single ROM Threads.
Thanks Guys for your help.
My issue is resolved with below post.
http://forum.xda-developers.com/showthread.php?t=1809098
phone not starting
guys i cant start my phone....even the three buttons ar not working...it is just loading and loading....help please
model-gt-s5830i
viral1999 said:
guys i cant start my phone....even the three buttons ar not working...it is just loading and loading....help please
model-gt-s5830i
Click to expand...
Click to collapse
You are here in totally wrong section: this is a i9000 help thread section. Hopefully you didn't flash a i9000 rom, otherwise your phone is hard bricked.
tetakpatalked from Nexus 7 flo
Me 2: It was from low battery in my case
I had similar problem when rooting my Samsung Galaxy S5 smartphone with Odin3. After rooting with a success message my phone was showing just the Samsung Logo each time I was trying to turn it on without loading OS. I googled and directed here and connected my phone to the charger as its mentioned in a link you provided which solved your problem. It turned on automatically after a few minutes while of charging and when turned on it was charged approximately 40%.
As I was very afraid my phone got serious harm at first I hope this maybe a sedative probability for duds really worry about what happened to their smartphone.
I rooted my phone le tv without pc bt after rooting it is not starting pls help me how to start my mobile again
Imbhavya said:
I rooted my phone le tv without pc bt after rooting it is not starting pls help me how to start my mobile again
Click to expand...
Click to collapse
What exactly did you do, which phone model and what does it display now?
Sent from my A0001 using Tapatalk