Hi,
could anyone help!
my device is galaxy ace s5830i
i have already rooted my device and used CW Recovery and taken a copy of my original system .oki
i wanted to set up a custom rom i restarted and reset and deleted the cash then installed the rom.
i think it was Retribution beta
then i wanted to update to that custom rom (MindCR ICS)
all i did i restarted my phone of course went into R mode and reset and deleted the cash then installed that next custom rom .
after installing completed when i rebooted it only gave me (samsung galaxy ace s5830i) logo and doesn't open the system when i restart it doesn't go into recovery or download mode it only gives me again the same logo.
even when i press long power button it shuts down and opens automatically.
is there any help knowing that i have already taken a copy of my system.
dana25 said:
After installing completed when i rebooted it only gave me (samsung galaxy ace s5830i) logo and doesn't open the system when i restart it doesn't go into recovery or download mode it only gives me again the same logo.
even when i press long power button it shuts down and opens automatically.
is there any help knowing that i have already taken a copy of my system.
Click to expand...
Click to collapse
I think you have a hard brick.....
Maybe JIG / JTAG can help.
Sent from my GT-S5830i using xda premium
RubenStauttener said:
I think you have a hard brick.....
Maybe JIG / JTAG can help.
Sent from my GT-S5830i using xda premium
Click to expand...
Click to collapse
would you provide me with that or tell me how?
dana25 said:
Hi,
could anyone help!
my device is galaxy ace s5830i
i have already rooted my device and used CW Recovery and taken a copy of my original system .oki
i wanted to set up a custom rom i restarted and reset and deleted the cash then installed the rom.
i think it was Retribution beta
then i wanted to update to that custom rom (MindCR ICS)
all i did i restarted my phone of course went into R mode and reset and deleted the cash then installed that next custom rom .
after installing completed when i rebooted it only gave me (samsung galaxy ace s5830i) logo and doesn't open the system when i restart it doesn't go into recovery or download mode it only gives me again the same logo.
even when i press long power button it shuts down and opens automatically.
is there any help knowing that i have already taken a copy of my system.
Click to expand...
Click to collapse
I have this problem before and i managed to use ODIN3 v1.83 (can use Odin3 v3.07) to detect my phone and flash a stock rom onto the device. I followed the advice given on this excellent thread by Supermini.
http://forum.xda-developers.com/showthread.php?t=1071970
As mentioned on his thread make sure you have the latest stock firmware from the sammobile site or by using Check Fus Downloader as per the guide in Rafael thread http://forum.xda-developers.com/showthread.php?t=1551156, a working samsung USB driver to detect your mobile on your PC and a copy of ODIN3 v1.83 (or v1.84, v1.87, v3.07 run ODIN in administrator mode if using in windows). Ultimately if this this fails you could always try a USB jig which can be purchased from ebay, etc. to get the phone into download mode.
Good luck and if this helps make sure you send a thank you to Supermini.
Viprdxd said:
I have this problem before and i managed to use ODIN3 v1.83 (can use Odin3 v3.07) to detect my phone and flash a stock rom onto the device. I followed the advice given on this excellent thread by Supermini.
http://forum.xda-developers.com/showthread.php?t=1071970
As mentioned on his thread make sure you have the latest stock firmware from the sammobile site or by using Check Fus Downloader as per the guide in Rafael thread http://forum.xda-developers.com/showthread.php?t=1551156, a working samsung USB driver to detect your mobile on your PC and a copy of ODIN3 v1.83 (or v1.84, v1.87, v3.07 run ODIN in administrator mode if using in windows). Ultimately if this this fails you could always try a USB jig which can be purchased from ebay, etc. to get the phone into download mode.
Good luck and if this helps make sure you send a thank you to Supermini.
Click to expand...
Click to collapse
thanks and sorry for late but as i told you i cant go into rev or download mode i tried to use odin 1.8 and the latest version but it doesn't recognize my phone shall i lose hope!
bro i think u most probably bricked ur phone but dont worry try opening download mode. then using the odin u install ur stock rom. Then u can access ur r mode. but try to read the entire procedure..of flashing the rom.
dana25 said:
thanks and sorry for late but as i told you i cant go into rev or download mode i tried to use odin 1.8 and the latest version but it doesn't recognize my phone shall i lose hope!
Click to expand...
Click to collapse
So . . . last thing to rescue your phone is buy on e-bay or in other place JIG if it isn't help you then try in phone service and say you tried install new ROM with Kies and your phone is brick (maybe it'll work).
Say to Service Centre Representatives that you kept your at charging last night
And when you woke up
It was not booting up
Pretend as if you dunno anything about root or ROM
They fixed my bricked phone
I am not sure if I am breaking any forum rule by telling this
Hey bro sorry for the late reply also, please before you do anything else try following my instructions.
1) download Odin v3.07
2) source the stock firmware you want to flash from sammobile.
3) make sure you have the Samsung mobile driver.
4) open and run Odin as administrator and load the single file in the PDA and highlight the tick box.
5) shut the phone down and take out your Sim card.
6) put the mobile into download mode as normal (press both up/down vol keys +power)
7) connect the phone to the PC and check in Odin to make sure its com port is detected.
8) then flash through Odin as normal.
I understand what your saying about no download screen appearing, I have found through experience that custom kernels can cause no download screen to appear. Normally with stock kernel this is not a problem but with custom kernels sometimes all you get is a black screen. Ignore this and just make sure that Odin is detecting the phone and try to flash, chances are it will flash the stock ROM and kernel. If you get the setup connection error in Odin and the fail 0\1 just try another USB port on your PC and keep persevering.
Please keep us updated so we can help you if you need it.
Sent from my Nexus 7 using xda app-developers app
Why will it be hardbricked if the custom roms are based on s5830i stock roms?
But it is probable that we did I not flash the rom properly as per procedure..so is there a chance that it be bricked? Else the rom may have some problem... just telling the probability
Sent from my GT-S5830i using xda premium
Help me .
help me on fixing my ace s5830i , my problem is after flashing it with RazoDroiD my phone seems to be ok , i decided to change my firmware by a stockrom using Odin mode or the Volume Up+Down+On off it stays on blank screen . Can you help me on fixing this ? and what do you call this problem .
Try following my instructions.
1) download Odin v3.07
2) source the stock firmware you want to flash from sammobile.
3) make sure you have the Samsung mobile driver.
4) open and run Odin as administrator and load the single file in the PDA and highlight the tick box.
5) shut the phone down and take out your Sim card.
6) put the mobile into download mode as normal (press both up/down vol keys +power)
7) connect the phone to the PC and check in Odin to make sure its com port is detected.
8) then flash through Odin as normal.
I understand what your saying about no download screen appearing, I have found through experience that custom kernels can cause no download screen to appear. Normally with stock kernel this is not a problem but with custom kernels sometimes all you get is a black screen. Ignore this and just make sure that Odin is detecting the phone and try to flash, chances are it will flash the stock ROM and kernel. If you get the setup connection error in Odin and the fail 0\1 just try another USB port on your PC and keep persevering.
Follow this and don't worry about black screen just make sure Odin detects your PC com port.
Sent from my Nexus 7 using xda app-developers app
Related
Ok so i decided to root my phone using this method darkys installation-guide-for-first-time-users after doing the first step for root using odin.Now after reboot it gets stuck on the initial screen were it says galaxy s gt i9000 and vibrates after intervals.What im able to do at the moment is go into recovery which seems to be 2e now prior to the root it was 3e and i can also start the phone in download mode.Please help me out or let me know what needs to be done.I really appreciate any feedback.
Thanks!
Wich Version of Darky´s ROM did you tried to flash?
One ask Darky its his rom his instructions you followed .
Two remove Darky rom flash back to stock.
http://forum.xda-developers.com/showthread.php?t=723596
jje
xivv1 said:
Wich Version of Darky´s ROM did you tried to flash?
Click to expand...
Click to collapse
JJEgan said:
One ask Darky its his rom his instructions you followed .
Two remove Darky rom flash back to stock.
http://forum.xda-developers.com/showthread.php?t=723596
jje
Click to expand...
Click to collapse
I have not flashed the rom yet this issue started exactly after rooting which is the first step i suppose.
These are the steps i followed:
For Froyo (2.2 and 2.2.1)
You need to grant yourself superuser access to system files on the phone. You also need Recovery 2e. You do that by installing CF-Root using the Odin flashing software.
1.1 - Pick the CF-Root matching your Firmware Version here
(take the v1.17 Busybox Version).
1.2 - Download Odin for Windows here.
1.3 - Install the needed USB drivers.
1.4 - Connect your phone to the computer and make sure that your phone has been recognized by Windows. You may need to do this several times before all drivers are configured correctly (unplug-plug-wait-unplug-plug until no more "Installing drivers" occurs).
1.5 - Unzip the downloaded file on your desktop.
1.6 - Make sure that your phone is NOT connected to your computer!
1.7 - Run Odin and make sure that that Partition and Clear EFS is not checked.
Just click on the PDA button and select the .tar file from your unzipped CF-Root file.
1.8 - Turn off your phone completely.
Restart it in Download Mode (Keep pressing both Volume Down + Home, press Power until the screen goes on). The phone will show a yellow logo and the word 'Downloading'.
1.9 - Connect your phone via the USB cable.
Odin should now recognize your phone (a COM port lightens up in yellow).
1.10 - Click on the Start button and wait while Odin flashes the CF-Root kernel.
1.11 - Your phone will automatically reboot when the flashing is complete.
The phone got stuck after the reboot and vibrates.Hope this helps for you guys to figure out the issue.
Thanks!
Download this Update.zip : http://www.multiupload.com/6OU2AGRSOD
Get into recovery mode and mount your sdcard. Connect your Phone via usb and open a command line window from your adb directory and enter this command : adb push Update.zip /sdcard Update.zip
Wait some sec and reboot your phone into recovery mode and apply sdcard: Update.zip
Try to root like this and tell me if it worked.
xivv1
Sent from my GT-I9000 using XDA App
First of thanks for the reply and i'll try my best what you told me to do and certainly get back to you!
BTW could you plz tell what is adb directory and how do i go about it?
Ill help you when Im back at home. Got some download links for you at my pc .Ill be at home at 17:00. Cya
Sent from my GT-I9000 using XDA App
rocky6 said:
First of thanks for the reply and i'll try my best what you told me to do and certainly get back to you!
BTW could you plz tell what is adb directory and how do i go about it?
Click to expand...
Click to collapse
I think you should use Odin to flash back to older firmware and start from scratch.
https://www.wuala.com/Samsung Galax...al Firmwares/Europe/October/?key=AfzUZSU4SpKU
Download the JPM firmware, put it into PDA in Odin (make sure re-partition is unchecked) and flash again.
xivv1 said:
Ill help you when Im back at home. Got some download links for you at my pc .Ill be at home at 17:00. Cya
Sent from my GT-I9000 using XDA App
Click to expand...
Click to collapse
splish2010 said:
I think you should use Odin to flash back to older firmware and start from scratch.
Download the JPM firmware, put it into PDA in Odin (make sure re-partition is unchecked) and flash again.
Click to expand...
Click to collapse
Really appreciate all the help i am getting from you guys.Ok so i flashed the firmware that you told me with odin everything went fine the phone started up fine.Now as i sweep the screen i get this messege "Sorry! the process android.process.media has stopped unexpectedly.please try again" below is an option for force when i click on it closes.Below it there is another messege "sorry! the application logsprovider(process com.sec.android.provider.logsprovider)has stopped unexpectedly.please try again" not able force the previous messege pops up.Not able to do anything on the phone.
Heres what i did turned off the phone started in recovery mode did a factory reset,wipe cache and formatted the sdcard and restarted the phone everything went fine no more messeges and i am able to use my phone thanks to u guys.Actually i am in luv with guys for helping me through this great work.I appreciate all the effort thanku once more u made my day!
No problem mate, hf using your phone
Sent from my GT-I9000 using XDA App
Firmware upgrade encountered an issue. Please select recovery mode in kies & try agai
i was trying to root my note something happen now i cant do nothing!!!in the screen say'''
Firmware upgrade encountered an issue. Please select recovery mode in kies & try again even kies cant conect to the phone
PSYCHOBOY18 said:
i was trying to root my note something happen now i cant do nothing!!!in the screen say'''
Firmware upgrade encountered an issue. Please select recovery mode in kies & try again even kies cant conect to the phone
Click to expand...
Click to collapse
what have you tried to do to fix this already?
ICS Bad Idea!!!
I wouldnt recommned updating to ICS especially through kies i had my phone stuck at "firmware upgrade encountered an issue please select recovery mode in kies and try again" for 2 days It was a disaster. So i came across a website called http://androidromupdate.com/2012/09...-firmware-upgrade-official-kiesota-stock-rom/
I then downloaded the the I927UCLH2 ICS 4.0.4 Original Stock ROM using ODIN... FOLLOW DIRECTIONS THROUGH THE SITE NOT KIES!! BUT THE ORIGINAL STOCK ROM!
***After you have successfully completed the stock rom with ODIN***
Get a rom from http://forum.jakar.co/android-hack/1345758298/ Choose the ROM called Bio360 its almost the same Replica of Gingerbread its Version 2.3.5
VERY IMPORTANT!! Make sure you put the ZIP FILE (ROM) in your INTERNAL STORAGE NOT THE EXTERNAL!!! (SD CARD SLOT) BIG MISTAKE!!
Go to google and type in "CWM captivate glide new" click the first link beggining with www.theandroidsoul.com........ FOLLOW DIRECTIONS THROUGH THE SITE!
After you have downloaded the Rom (ZIP FILE) and CWM put your phone into Recovery mode by powering off the device. hold power button and the volume down button until you see clockwork recovery, from here you are going to look for install from sd card and look for the zip file/Rom Bio360 and you should be set!
*******THE Bio360 Rom is also Rooted so there is no need to do an extra step************
*** I HOPE THSI HELPS ANY PROBLEMS FEEL FREE TO INBOX ME ANY QUESTIONS*** I WILL TRY MY BEST TO HELP......
Sorry guys wrong post this is for Samsung captivate glide! , my mistake..
Sent from my SAMSUNG-SGH-I927R using xda premium
Firmware upgrade encountered an issue. Please select recovery in Kies and try again
This is for Samsung Galaxy Note 2 (Sprint SPH-L900) Is the website for the stock rom
rwilco12.com
stock rom: [ROM][ODIN][TAR]SPH-L900 MA7 (MA7 Modem/Kernel/ROM - Stock
Odin 3 v 1.85 (You Can Google and find it)
ok sweet so I have done this successfully. i really believe you should put this on ur first post so people dont have to do searching and can feel at ease.
1. Start ODIN 3v1.85
2. Enter Download Mode
a. Power the phone off.
b. Plug the usb cable into the computer (not the phone)
c. Hold both sides of the volume rocker down (vol up + vol down)
d. While holding those buttons down, insert the usb cable into your phone.
It may take a second or two for the screen to display with a warning. Press the Volume UP key to download a custom ROM.
3. In ODIN, click PDA and select the PDA.tar file you extracted
4. DO NOT check re-partition, Flash Lock, Phone EFS Clear, Phone bootloader update
5. CHECK Auto Reboot and F.Reset Time
6. Click Start
At the end of the process ODIN's first block will show up as YELLOW with the words PASS and your phone will reboot.
Unplug USB from your phone after first boot.
It worked for me perfectly you don't have to F.Reset
Perhaps you should try the Note 2 forums for a more informative response?
I have the same problem with my tmobile galaxy s ii, T989
Firmware upgrade encountered an issue. Please select recovery mode in kies & try again
and whenever I start installing a stock room using Odin 1.85 it force close and the phone stays in the same page saying
Firmware upgrade encountered an issue. Please select recovery mode in kies & try again
Please help!
Tried everything I know and still not working
I tried two computers and everytime I start odin it forces stop
The screen is still in Firmware upgrade encountered an issue. Please select recovery mode in kies & try again
and I guess this is the download mode because I restarted it with volume up and down and pluged the usb and it turns to this screen
I downloaded odin again to make sure it runs ok and also tried it in my wifes phone and it runs with no problem
It is one of two cases, ether the phone is completely dead or the files I am using to be installed are not the correct ones
I tried the files on this post:
http://forum.xda-developers.com/showthread.php?t=1414341
Please tell me what to do
I really need the phone...
this is d screen i get wen i try to restart d fone..... please help
Turn it in download mode after removing battery once and then flash new rom using odin. ...
Thats only solution i think as i have experienced same problem several times
sent from heaven
arpitkh96 said:
Turn it in download mode after removing battery once and then flash new rom using odin. ...
Thats only solution i think as i have experienced same problem several times
sent from heaven[/ive tried it.. but odin is not working.. it s force closing.. as u can see from my screen image that download from pc to mobile is disabled..
Click to expand...
Click to collapse
I've gotten this before. I think it's caused by a failed flash in a rom, either interrupted or something else. The way I solved this was to pluck out the battery, put it back in, boot into download mode (power+home+vol down buttons). Then make sure u have Samsung usb driver installed and then run Odin as administrator. Continue to flash the stock firmware.
Sent from my GT-S5570 using xda app-developers app
take it as second download mode
just connect it with Odin and flash the firmware
this normally happens when flashing process is interrupted
as u can see from my screen image that download from pc to mobile is disabled..
Click to expand...
Click to collapse
Also, the exclamation mark (!) between the computer and phone icons do not symbolise unable to connect to pc. It means something like "the phone needs to be connected to the computer to flash another firmware."
dheeraj (dhlalit11) said:
take it as second download mode
just connect it with Odin and flash the firmware
this normally happens when flashing process is interrupted
Click to expand...
Click to collapse
i ve tried that earlier.. but it says..' odin has stopped working'.... after clicking start in odin
use different firmware or odin
dheeraj (dhlalit11) said:
use different firmware or odin
Click to expand...
Click to collapse
it happened to me last week,,, try another usb port,,, or another computer,,,
vinup dasari said:
this is d screen i get wen i try to restart d fone..... please help
Click to expand...
Click to collapse
Bro, Don't worryYou can have it working. The exact scenario happened with me too. It happens when you enter in download mode & then due to some reason, you try to switch it on normally. In such case, it won't open either normally or in recovery, but only in Download Mode. So, remove battery, insert it again & press the Download Mode combo keys to enter download mode (Download mode works in such cases) & follow these guidelines:-
1. If odin is crashing, try another pc.
2. If odin is not recognizing your device even when correct drivers are installed, Then check the name of OPS file. For MINI it should be "Tass_v1.0.ops" (without quotes). Note that, device model number appears in Odin's Title Bar.
3. After that If Odin is hanging in btw (for ex: in setup connection), try another USB port.
5. If still problem persists, try another stock firmware.
6. If firmware update is successful and phone bootloops, remove battery, go to stock recovery mode & wipe data/factory reset. Then, wipe cache.
If you implement these correctly, it's 100% gauranteed that your phone should be normal.
Your problem should be solved by then.
Sent Via XDA™ Premium
Hi,
I have Samsung Galaxy S I9000 running Ginger Bread.
I wanted to upgrade my phone to Ice Cream Sandwitch or Jelly Beans. In order to do it, I started with below steps to root my mobile.
1. Installed latest Clockwise Mode application into my phone.
2. Installed Odin3 v1.7 in my laptop.
3. Downloaded CF-Root-XX_XEU_JPY-v1.3-BusyBox-1.17.1.tar on my laptop.
4. Started Odin first.
5. Disconnected mobile and started in download mode with Volume Down + Home Button + Power Key.
5. After starting the download mode, connected mobile to laptop using the USB.
6. Keep all the default values in Odin3 i.e. Re-Partition option unchecked, Auto Reboot and F-Reset Time option enabled. Selected tar file CF-Root-XX_XEU_JPY-v1.3-BusyBox-1.17.1.tar in PDA option.
7. Connected mobile and it detected ID Comm [Highlighted in Yellow].
8. Finally click on Start button.
After starting the process was completed and Yellow color changed to Green one, phone was auto reboot.
But after reboot it is just stuck on start of screen and not going ahead. I wait for 2 hours but still not working.
Could you please help me how I can solve this issue now?
Did you try to pull battery out and restart the phone again?
Do you still can go in CWM with 3 button combo again?
If yes then try to flash a ICS or JB kernel (depending on what ROM you finally want to have on your phone) via CWM and then go in advanced and restart recovery (if available), otherwise just try to flash the rom.zip on top.
If CWM is not possible, the go in download mode an falsh a tar version of kernel via ODIN.
Here are different semaphore kernels for each android version:
http://78.46.194.137/downloads/gt-i9000-ics
http://www.semaphore.gr/downloads/gt-i9000-jb
For ics it should work after 1. flash, but for JB you have to flash it 2 or even 3 times, if after restart phone does not boot. Then battery out again, start in recovery and flash zip again.
Good luck and good success .
I think, at this position, installing a new gingerbread stock ROM will be preferable. Try installing XXJVU. Then root with cwm and install any slim bean version in case you are interested to use jelly bean.
Sent from my GT-I9000 using xda app-developers app
Sure that will be the best way....but my suggestions do not take much time, so why not give them a try .
But if its not going, then a restock is the best you are right:
What I always do for restock is using slappys rescue kit.
Unzip it and flash the Rom via Odin. There is everything, also a txt file with a guide included.
http://forum.xda-developers.com/showpost.php?p=29114573&postcount=2
If you want to have slim rom then its recommended to flash CM9 first or flash a modem afterwards via cvm, because slim does not have a modem included.
And/Or just follow the installation guides/recommendations from the single ROM Threads.
Thanks Guys for your help.
My issue is resolved with below post.
http://forum.xda-developers.com/showthread.php?t=1809098
phone not starting
guys i cant start my phone....even the three buttons ar not working...it is just loading and loading....help please
model-gt-s5830i
viral1999 said:
guys i cant start my phone....even the three buttons ar not working...it is just loading and loading....help please
model-gt-s5830i
Click to expand...
Click to collapse
You are here in totally wrong section: this is a i9000 help thread section. Hopefully you didn't flash a i9000 rom, otherwise your phone is hard bricked.
tetakpatalked from Nexus 7 flo
Me 2: It was from low battery in my case
I had similar problem when rooting my Samsung Galaxy S5 smartphone with Odin3. After rooting with a success message my phone was showing just the Samsung Logo each time I was trying to turn it on without loading OS. I googled and directed here and connected my phone to the charger as its mentioned in a link you provided which solved your problem. It turned on automatically after a few minutes while of charging and when turned on it was charged approximately 40%.
As I was very afraid my phone got serious harm at first I hope this maybe a sedative probability for duds really worry about what happened to their smartphone.
I rooted my phone le tv without pc bt after rooting it is not starting pls help me how to start my mobile again
Imbhavya said:
I rooted my phone le tv without pc bt after rooting it is not starting pls help me how to start my mobile again
Click to expand...
Click to collapse
What exactly did you do, which phone model and what does it display now?
Sent from my A0001 using Tapatalk
Hello, this is my first post, but no one cares. Right?
I have a little story... Today I tried to Upgrade from CM 10.1 to CM 10.2 but I had a little problem. Because I wanted to have a fresh instalation I first tried to flash with ODIN 3.0.4 official 2.3.6. In the middle of instalation... I had a power outage for 5 seconds. Now my problem is:
1. It can't enter Recovery;
2. It can't enter Download Mode;
3. It can't boot System.
When i plug the usb cable, it shows me this message: "Firmware upgrade encountered an issue. Please select recovery mode in kies and try again. ", but that's a little strange because I don't even have Kies installed on PC. This is the only scree I can see.
I don't know how, but somehow I entered Download Mode for 5-10 seconds, but my PC doesn't recognize my phone. After that the phone just shuted down.
I already browse all topics about soft brick, but nothing helped me...
Before take my phone to a service, what are my other choices?
DanuTzCarbon said:
Hello, this is my first post, but no one cares. Right?
I have a little story... Today I tried to Upgrade from CM 10.1 to CM 10.2 but I had a little problem. Because I wanted to have a fresh instalation I first tried to flash with ODIN 3.0.4 official 2.3.6. In the middle of instalation... I had a power outage for 5 seconds. Now my problem is:
1. It can't enter Recovery;
2. It can't enter Download Mode;
3. It can't boot System.
When i plug the usb cable, it shows me this message: "Firmware upgrade encountered an issue. Please select recovery mode in kies and try again. ", but that's a little strange because I don't even have Kies installed on PC. This is the only scree I can see.
I don't know how, but somehow I entered Download Mode for 5-10 seconds, but my PC doesn't recognize my phone. After that the phone just shuted down.
I already browse all topics about soft brick, but nothing helped me...
Before take my phone to a service, what are my other choices?
Click to expand...
Click to collapse
Sorry my friend only samsung can help you!!!
Sent from my GT-S5570 using xda premium
uninstall your kies. then install samsung usb driver.
then odin your phone.
dzeig said:
uninstall your kies. then install samsung usb driver.
then odin your phone.
Click to expand...
Click to collapse
I can't enter Download Mode and I haven't KIES installed.
Since you had a power outbreak during Odin flashing, it might not fully flash the bootloader (boot.img file), or the fat.bin file, both of them are essential for proper phone operation.
Install Kies, and try the recovery mode in it, see if it works.
Also, try to charge your battery, maybe this will help somehow.
If nothing works, service is your only option, as you cannot manually repair a partially flashed boot.img or fat.bin.
boot.img is not bootloader,
Boot.img is kernel
Tapnięte z mojego mini 2
MrMateczko said:
Since you had a power outbreak during Odin flashing, it might not fully flash the bootloader (boot.img file), or the fat.bin file, both of them are essential for proper phone operation.
Install Kies, and try the recovery mode in it, see if it works.
Also, try to charge your battery, maybe this will help somehow.
If nothing works, service is your only option, as you cannot manually repair a partially flashed boot.img or fat.bin.
Click to expand...
Click to collapse
Well, I installed Kies.
I can't use "Emergency firmware recovery" because my PC doesn't recognize my phone.
I can't use "Firmware Upgrade and Initialisation". When I enter the details about my phone I get "'GT-S6500D' does not support initializing.".
I don't think I have other option in Kies...
Another problem:
My phone is absolutely unresponsive.
Maybe because of battery.
I can't charge it. I have a friend with S6500D...
I will try with he's battery.
Maybe I could try some tricks to enter in Download Mode. (God, please help me!!)
Instal drivers and go to download mode !
Tapnięte z mojego mini 2
hheelloo said:
Instal drivers and go to download mode !
Tapnięte z mojego mini 2
Click to expand...
Click to collapse
I have drivers. Isn't that the problem. And I said I can't enter Download Mode.
Sorry but your phone is hard bricked so you can't fix your phone yourself.You have to send it to samsung to fix it.The hard brick was caused by failed bootloader update.But if you have power surges i recommend you to flash your phone from a laptop.
darkshadow1997 said:
Sorry but your phone is hard bricked so you can't fix your phone yourself.You have to send it to samsung to fix it.The hard brick was caused by failed bootloader update.But if you have power surges i recommend you to flash your phone from a laptop or flash stock rom with bootloader removed link:http://forum.xda-developers.com/showthread.php?t=1551586
Click to expand...
Click to collapse
Thanks for the advice.
Please ignore the link to stock firmware without bootloader because i did not know your phone was galaxy mini 2 because sometimes mini 2 questions are posted in mini 1.And i have both mini and mini 2.
If boot.img is not the bootloader (it's the kernel, I'm sorry for telling you wrong before), then why the Download Mode does not work?
darkshadow1997 said:
Please ignore the link to stock firmware without bootloader because i did not know your phone was galaxy mini 2 because sometimes mini 2 questions are posted in mini 1.And i have both mini and mini 2.
Click to expand...
Click to collapse
It doesn't matter... I saw it was for Mini... Anyway download mode still not working so don't worry.
Thanks for the idea of stock firmwares without bootloader... maybe i could edit stock firmwares for my phone.
You can edit stock rom without the risk of hardbrick.just upack your stock rom then delete bootloader then download a software to create tar do not use tar editor because just deleting the bootloader doesn't mean odin will load it maybe because of md5.So did you send your phone to samsung.
darkshadow1997 said:
You can edit stock rom without the risk of hardbrick.just upack your stock rom then delete bootloader then download a software to create tar do not use tar editor because just deleting the bootloader doesn't mean odin will load it maybe because of md5.So did you send your phone to samsung.
Click to expand...
Click to collapse
Well... my brother know a guy who know another guy. This guy have a service or something like that. I sent the phone to him. Maybe he could do something. If not... I will try to find the famous Usb Jig for my model of mini. I found for GT-S5570 but still searching for GT-S6500D
Fixed
Well... I sent my phone to a service but there they could only fix download mode. LOL. They tried to install firmware update, but the phone was stuck in bootloop. From there, I fixed by myself.
I will ask them how did they fix it.