Related
I am not sure what I have done. I have a cingular 8125 G4. Downloaded the Risidioro g4 rom upgrade and my phone was not probably CID unlocked. Thought that did not matter cause I was able to install Mr Clean ROM couple of months back. I read some users in the forum who successfully upgraded from Mr Clean.
Everything went nice and smooth, the upgrade completed 100% and when it finished and rebooted it stopped at the blue, red screen and got stuck there. I did soft reset, hard reset but every time that blue, red screen comes up and gets stuck.
Has my phone become a "nice but dead piece of furniture" ? Oh! man..that would devastating!
Please help!
BigMonty
All right, no response yet but it is only a hour since I posted but for me it seems eternity already. I did something further reading and got some hope. My phone might not be dead yet. Somebody said, if I can get to the bootloader mode, I still have some hope.
I did some trick on hard resetting found here
http://forum.xda-developers.com/showthread.php?t=268836&highlight=dead
but to no avail.
Any other idea?? Cry!! Cry!! Cry!!!
Got another guy who successfully got out of the jail by having a SD image. Do you think it would work for me too? If it works where can I find it? I already e-mailed the guy, seems like a nice guy, let's see if he replies.
http://forum.xda-developers.com/showthread.php?t=274471&highlight=dead
Do you see a USB connection if you connect it to Active sync, normally it is showing in the lower left or right corner, I'm not sure.
If so, you should be able to re-flash again, best would be to do this with your previous installed ROM.
Btw,
Spl 2.25.0001
Ipl 2.25.0001
Can somebody suggest what would be most suitable ROM to go for once I am in the bootloader screen?
Vilem said:
Do you see a USB connection if you connect it to Active sync, normally it is showing in the lower left or right corner, I'm not sure.
If so, you should be able to re-flash again, best would be to do this with your previous installed ROM.
Click to expand...
Click to collapse
Thanks a lot Vilem for your reply. Yes I see a USB connection..but I guess we can't get to activesync because the OS did not load yet. I had the Mr Clean ROM installed and I tried to go for it but failed. What should I do now? Go for the original shipped Cingular ROM?Anybody knows which version it was and where can I find it?
bigmonty said:
I see a USB connection..
Click to expand...
Click to collapse
Means connected, try it. Mine crashed a couple of times like that and managed to get it going again.
You mean I should run the Mr Clean update utility which is the last successful ROM update or the orginial Cingular shipped ROM?
bigmonty said:
You mean I should run the Mr Clean update utility which is the last successful ROM update or the orginial Cingular shipped ROM?
Click to expand...
Click to collapse
try the last succesful.
bigmonty said:
All right, no response yet but it is only a hour since I posted but for me it seems eternity already. I did something further reading and got some hope. My phone might not be dead yet. Somebody said, if I can get to the bootloader mode, I still have some hope.
I did some trick on hard resetting found here
http://forum.xda-developers.com/showthread.php?t=268836&highlight=dead
but to no avail.
Any other idea?? Cry!! Cry!! Cry!!!
Click to expand...
Click to collapse
Bigmonty - after getting into allsorts of issues after trying to upgrade my G4 to various 3.2 based ROMS, i also got to the bootloader screen with the USB indicator in the righthand corner.
This worked for me - take the battery out for an hour or so, put back in and soft reset. make sure you have a good charge. reboot the PC and plug in the device.
Now the only ROM i can recover a working device from isto use the latest ROM from the phone supplier. in my case from the club i-mate site (my device is SIM unlocked).
hope it helps
Thanks AirWol. I was able to go back to Mr Clean successfully, which was a great relief. What I was doing wrong was, I was using the wrong update utility of Mr Clean. I should have used the one which was modified according to Risidioro guide for use in g4 chips. But I was using the original Mr Clean instead.
BTW, anybody knows whether it is possible to update g4 phones to the latest Risidioro or Cingular 2.26 ROMS? That is, can I modify according to Rididioro guide for use in g4? Anybody?
Probably I haven't learned enough lessons yet!
So, you've decided that your shiny new toy isn't very well setup by default. You flashed a ROM and lo and behold, you missed some instruction somewhere and now you think it's bricked.
Here's the good news:
It's not bricked!!
Bricked means that it's dead and it's in no way or shape recoverable.
There is still a chance. (As long as you didn't try to hardSPL with another Device's SPL...)
All you have to do is:
For the WING:
Hold the Camera button and WHILE holding it, soft reset the device (that means press the little hole above the memory card with the stylus.) That will bring you to the bootloader. Now download the appropiate RUU and run that program. A few minutes later and your new shiny toy is back to it's crappy OEM but working self!
I'll put in links for those who can't find them...
Here's tmobile's ROM.
WOW! That´s all??
Ok - then provide us a link to a XDA Terra RUU!!!!!!
hahahaha. Thanks for this help. Maby for some people it is usefull - but written 1000 times before.
ivanmmj said:
So, you've decided that your shiny new toy isn't very well setup by default. You flashed a ROM and lo and behold, you missed some instruction somewhere and now you think it's bricked.
Here's the good news:
It's not bricked!!
Bricked means that it's dead and it's in no way or shape recoverable.
There is still a chance. (As long as you didn't try to hardSPL with another Device's SPL...)
All you have to do is:
For the WING:
Hold the Camera button and WHILE holding it, soft reset the device (that means press the little hole above the memory card with the stylus.) That will bring you to the bootloader. Now download the appropiate RUU and run that program. A few minutes later and your new shiny toy is back to it's crappy OEM but working self!
I'll put in links for those who can't find them...
Click to expand...
Click to collapse
papamopps said:
WOW! That´s all??
Ok - then provide us a link to a XDA Terra RUU!!!!!!
hahahaha. Thanks for this help. Maby for some people it is usefull - but written 1000 times before.
Click to expand...
Click to collapse
I know it has been stated a million times. I'm just tired of the same question being asked over and over again and so here we are...
Too bad it'll be stated a million more times afterwards too.
falconeyez said:
Too bad it'll be stated a million more times afterwards too.
Click to expand...
Click to collapse
If we sticky it and threatened their lives if they don't read it... lol
ivanmmj said:
For the WING:
Hold the Camera button and WHILE holding it, soft reset the device (that means press the little hole above the memory card with the stylus.) That will bring you to the bootloader. Now download the appropiate RUU and run that program. A few minutes later and your new shiny toy is back to it's crappy OEM but working self!
Click to expand...
Click to collapse
It will not help!
ASerg said:
It will not help!
Click to expand...
Click to collapse
And we hold their pet's hostage?
ivanmmj said:
And we hold their pet's hostage?
Click to expand...
Click to collapse
Or better yet, tell them to send us their phones, then we "unbrick" them and sell them on eBay.
falconeyez said:
Or better yet, tell them to send us their phones, then we "unbrick" them and sell them on eBay.
Click to expand...
Click to collapse
Might work out, I get 10% of the over all sold
Ghostrider
Ghostrider said:
Might work out, I get 10% of the over all sold
Ghostrider
Click to expand...
Click to collapse
Fine, but I get 15% because it's my thread.
The instructions to do this are actually in my newbie thread. Which is a sticky.
TylerC161 said:
The instructions to do this are actually in my newbie thread. Which is a sticky.
Click to expand...
Click to collapse
I know, but most people don't search. I figured, maybe if it says "How to fix your bricked phone" on the title, they might get the idea.
It was actually done mostly as a joke...
help
I used the hardSPL from this thread..
http://forum.xda-developers.com/showthread.php?t=358225
It worked successfully and I was able to restart into WM6. Then I tried loading the TouchIT 4.4 and it installed cleanly with no errors. But when I went to restart it, my Wing just sits there at the CanonYang boot screen and never changes.
I tried using the steps here to restore the tmo default rom, but it after 1% on the progress bar, the screen goes blank and the CanonYang screen comes back. Is there anything I can do?
edit: I can get to the bootloader screen with the color bars. I'm not sure if this additional info will be of any help.
IPL 4.10.0002
SPL 4.70.Yang
gumbico said:
I used the hardSPL from this thread..
http://forum.xda-developers.com/showthread.php?t=358225
It worked successfully and I was able to restart into WM6. Then I tried loading the TouchIT 4.4 and it installed cleanly with no errors. But when I went to restart it, my Wing just sits there at the CanonYang boot screen and never changes.
I tried using the steps here to restore the tmo default rom, but it after 1% on the progress bar, the screen goes blank and the CanonYang screen comes back. Is there anything I can do?
edit: I can get to the bootloader screen with the color bars. I'm not sure if this additional info will be of any help.
IPL 4.10.0002
SPL 4.70.Yang
Click to expand...
Click to collapse
SPL 4.70.yang!!! your device is HARD-SPL!!
So going back to stockrom--> delete the SPL.nbh from EVERY RUU you are running.
Then it shouldn´t stop......
Big Thanks papa! That did the trick. My Wing is happy once again and running Open Touch. But I still want to give TouchIt another try.
And what if i cant find stock RUU mine came with some arabic keyboard and spl was 1.08 , thanks to Oli he didnt mention that SPL should be 4 or higher , so device is bricked since first Olis release and no way to find this arabic stock RUU.
Any Help ?????
Hitec
If the device had an spl of 1.08 prior to HardSPLing it, then you'll have to bring the device to your nearest repair center. There isn't a way around that. Oli doesn't know everything and that's the risk we take when we try new and experimental things that people create but have no way of testing. But, we live and learn. If it wasn't for that issue, you could always cook your own ROM and if the HardSPL was working, you could've easily flashed any ROM. But the keyboard wouldn't been wrong until you could find someone who had the correct keyboard and you extracted the ROM from it and cooked that keyboard driver into your ROM.
Oh noooo!!
Hi ivanmmj,
I used your guide to flashing my HTC P4350 at http://forum.xda-developers.com/showthread.php?t=358615.
It was in French and I wanted it in English. So I downloaded one of the official HTC ROMs "HTC_P4350_WWE_4.17.405.2_4.1.13.44_02.94.90_Ship.exe" assuming this was the English one because all the others couldn't have been.
I copied the "RUU_signed.nbh" from the above HTC ROM and put it into the RUU folder as instructed by yourguide (I didn't copy the SPL.nbh file). I then ran the herald-uspl.exe and everything went fine until the RUU utility stopped with the error "invalid vender ID".
The RUU exited without completing, now all I get when the device boots is the screen giving my IPL (1.08.001) and SPL (1.08.001). How do I flash another ROM from this state? I can't do it the "normal" way because ActiveSync can't see the device. When I try to use the RUU tool that comes with your tool, the progress bar shows then it says the tool can't be used with my device.
Someone please help!
foo_bar_baz said:
Hi ivanmmj,
I used your guide to flashing my HTC P4350 at http://forum.xda-developers.com/showthread.php?t=358615.
It was in French and I wanted it in English. So I downloaded one of the official HTC ROMs "HTC_P4350_WWE_4.17.405.2_4.1.13.44_02.94.90_Ship.exe" assuming this was the English one because all the others couldn't have been.
I copied the "RUU_signed.nbh" from the above HTC ROM and put it into the RUU folder as instructed by yourguide (I didn't copy the SPL.nbh file). I then ran the herald-uspl.exe and everything went fine until the RUU utility stopped with the error "invalid vender ID".
The RUU exited without completing, now all I get when the device boots is the screen giving my IPL (1.08.001) and SPL (1.08.001). How do I flash another ROM from this state? I can't do it the "normal" way because ActiveSync can't see the device. When I try to use the RUU tool that comes with your tool, the progress bar shows then it says the tool can't be used with my device.
Someone please help!
Click to expand...
Click to collapse
Oh wow. I'm so sorry. I think I may have forgotten to put up a warning for people that have an SPL lower than 4.0. Was your SPL lower than 4.0? If it was, you cannot use the USPL OR the HardSPL and they end up writing part of the ROM over your current SPL and brick the device. This, unfortunately, needs to be fixed by your local repair center. I'll talk to the Mods about unlocking that thread so that I can update it.
ivanmmj said:
Oh wow. I'm so sorry. I think I may have forgotten to put up a warning for people that have an SPL lower than 4.0. Was your SPL lower than 4.0? If it was, you cannot use the USPL OR the HardSPL and they end up writing part of the ROM over your current SPL and brick the device. This, unfortunately, needs to be fixed by your local repair center. I'll talk to the Mods about unlocking that thread so that I can update it.
Click to expand...
Click to collapse
Oh deary me! I am so dead now - I live in Tanzania, East-Africa. My "local" repair center is several hundred thousand miles away across The Big Blue. What exactly do the repair center folks do to fix the device? Perhaps I can soldier out myself with some guidance...
Thank you,
foo_bar_baz.
Hi all i`m always changing my roms and radio`s like you do lol i had duttys rom installed and hard spl olinex 1.93 also. my problem is and like a true div i used the wrong program on the diamond cos i have the tytn aswell so put that program on my diamond and now it is bricked lol the program was hard spl for the tytn or something can`t remember exactly what. can`t get into bootloader or reset as nothing at all and wont start up or vibrate etc can`t get active sync to find phone so i would say 100% bricked lol i am sending the diamond tomorrow for repairs to htc.
what i want to know is as it has a cooked rom and olinex installed and i bought it new from someone who was selling their upgrade will they be-able to tell whats on the phone if it is bricked and then refuse to fix it or cos it is bricked they`ll never be-able to see what rom etc is installed on it??? it was originally on the orange network uk so would that affect the repair??
any help would be much appreciated keep up the good work to all xda-developers and forum user`s cheers tony
karaduke said:
Hi all i`m always changing my roms and radio`s like you do lol i had duttys rom installed and hard spl olinex 1.93 also. my problem is and like a true div i used the wrong program on the diamond cos i have the tytn aswell so put that program on my diamond and now it is bricked lol the program was hard spl for the tytn or something can`t remember exactly what. can`t get into bootloader or reset as nothing at all and wont start up or vibrate etc can`t get active sync to find phone so i would say 100% bricked lol i am sending the diamond tomorrow for repairs to htc.
what i want to know is as it has a cooked rom and olinex installed and i bought it new from someone who was selling their upgrade will they be-able to tell whats on the phone if it is bricked and then refuse to fix it or cos it is bricked they`ll never be-able to see what rom etc is installed on it??? it was originally on the orange network uk so would that affect the repair??
any help would be much appreciated keep up the good work to all xda-developers and forum user`s cheers tony
Click to expand...
Click to collapse
If you flashed the Tytn SPL to a Diamond, you can forget it, it is a shiny paperweight...
Unless the JTAG points for the device are found it is most definitely a brick.
lol thought as much lol thats what happens when you have more than one phone lol would they know it has a cooked rom installed when they investigate why it bricked? cheers
karaduke said:
lol thought as much lol thats what happens when you have more than one phone lol would they know it has a cooked rom installed when they investigate why it bricked? cheers
Click to expand...
Click to collapse
If they unbrick it, then yes, they will know it has a custom ROM flashed to it. However, they will still fix it and just bill you.
damn lol is there a way of blagging it so if i say i bought the phone with the cooked rom installed already and thought that was the original rom from new?? just play dumb lol is it expensive if they unbrick it?? cheers
just to add that dutty`s rom was great and had nothing to do with me bricking my phone. just incase people interpret me the wrong way and think its a rom problem
morning all my phone is being picked up today and was just wondering if they do fix or reflash my phone will it be back to being locked to the orange uk network again even though i unlocked it??? cheers
karaduke said:
morning all my phone is being picked up today and was just wondering if they do fix or reflash my phone will it be back to being locked to the orange uk network again even though i unlocked it??? cheers
Click to expand...
Click to collapse
HTC will flash the most recent ROM available for your device. If your phone is Orange branded, then that is the ROM they will flash to it.
thanks for that mate but i need to know if it will be locked back to orange uk meaning can i use any sim card or will it be on orange uk only cheers
anyone else with any suggestions please cos i`m getting a bit worried that htc will refuse to repair and if they do how much the cost will be. has anyone from the uk had the same problem and bricked there phone? and how much does it cost for them to repair?? thank you
just an update about my repair got my diamond back today and they replaced the main board cos i bricked the diamond so i have a new imei number and life time call counter is back to zero i never got charged for this repair and now i can even hard reset the phone where before it wouldn`t work so have faith if you have bricked your diamond
Hi, I have been reading this forum for some weeks and I am thinking of unlocking my Touch 3G by using this Hard-SPL thing which is available here.
However I am still hesitating because I have never done such an "intervention" in the past, so please allow me to ask you if you did it and if yes if it worked without problems (from the thread I wasn't able to understand if more that 2-3 people have really succedded!)
Thanks, lila
I actually tried few times yesterday and today, but I am getting "Server is down" message .
i manage to solve it. how? i have exit my antivirus, then, go to control panel/windows firewall and put it on off, and will work. each time, i have install enablerapi.cab on device memory.
I disabled firewalls and antivirus software. I tried on three different computers with different (working) access to internet. Still no joy . I guess I will try later.
I've unlocked my Jade without any problem, but to be honest i didn't flash another ROM yet because i want to be sure i can go back to original one (just in case of waranty), and i don't know how to rebuild my dumped original ROM.
I'm still trying to figure this out, gonna succeed as long as i keep reading this excellent forum.
Anyhow, flashing a new ROM isn't that difficult, but you have to follow the guidelines very well and keep on your reading glasses..)
Hi. I am very happy Thank you OLINEX. I have HTC 3G (Jade 100) I make HARD SPL and I install http://rapidshare.com/files/15981107...30.09_Ship.exe
rom. It is very good rom and stable. Now I have english language and my phone rings best. Thank you OLINEX.
fenikso said:
I disabled firewalls and antivirus software. I tried on three different computers with different (working) access to internet. Still no joy . I guess I will try later.
Click to expand...
Click to collapse
So, I finally got it to work. I will post my "story" to Hard-SPL thread .
i did it with the first attempt with v3, no problem and i'm really happy
Hard-SPL
With hard-spl you will not unlock your jade . It´s only necesary to upload others roms to device.
estancolaplaza said:
With hard-spl you will not unlock your jade . It´s only necesary to upload others roms to device.
Click to expand...
Click to collapse
Oh yes you are right, however that's what I meant; in fact I have a Jade with French ROM and I want to change it to English.
for me dont work the hard spl....
I've been trying for the past 3 days to Hard SPL my jade without any luck. always the phone restart without entering to tri color mode.
I even tried to exit the antivrus and disable the firewall but always same error.
Any suggestions here please?
fenikso said:
So, I finally got it to work. I will post my "story" to Hard-SPL thread .
Click to expand...
Click to collapse
Ca you post your story please maybe you can give us a little help.
Thank you
no luck with the one i tried, just restarts. dont know why this phone is so special, every other one ive done is so easy.
stock loader version is 1.40.707.2 tried using windows xp sp3 .net3.5, tried using hardspl v2 and v3 (tried v2 just in case that worked)
the link is dead!!
lots of problem, the HardSPL from Oli doesnt work, but the radio update from HTC works
keep trying and win
SPL does work. But you must keep trying. I got "server down"
and so on. After a week and hundred times try, I got unlocked the phone.
Now I can enjoy any wm6.5 roms. It is free software and not perfect.
But It does the job . well done Olipro and Cmonex.
Which phone do I have ?
My phone is supposed to be a Touch 3G but the processor is a Marvell PXA310 @ 624 MHZ.
The phone says it's a T3238, can someone tell me which phone I have please?
It's a clone I think.
When I boot holding the volume key I get a white screen saying USB update model
Hi,
I have a TOUCH 3G and I did the HARD-SPL. The better thing in here is that developers and always available to help you. For example, i had some problems doing hard-spl to my Jade but with the help of cmonex(developer) i've done it without any problems. You have a lot of support in here. SO, If I were you, I would do it.
it works like a charm
hi
Yes i did my HSPL today and it worked like a charm it was so easy and
i had a gene(P3400i) and the HSPL for this phone was so difficult
compare to the HSPL for Jade
the Jade HSPL took only around 10-15 mins
now i need to flash some cooked rom will do it today right now downloading ironegles ROM
Note : u need to off ur Firewall or it wont work OK
A few days ago I could not boot my X1 after flashing to a new rom. It came up with "Loading" and no image found. I was able to recover it with MTTY using a windows XP machine. I am now trying to flash to the newest version of CHristian's rom but I can't even hard SPL without getting stuck at the "loading page" again. I am able to pull the battery out and place it back in to boot back up to the OS. I also tried to do the SD card method and that didnt work.
I think something is wonky as last time I hard SPL'd it was a "success" but it just reloaded an old version of Christians Rom.
Please help. I have searched high and low on the forums and all i can find is people with the problem but no answers.
Thank you!
hey im nt no expert but have you tryied hard reseting the device to default settings, then formatting your memory card and then trying to port the rom across? i wonder if that would help!
confusedtadpole said:
hey im nt no expert but have you tryied hard reseting the device to default settings, then formatting your memory card and then trying to port the rom across? i wonder if that would help!
Click to expand...
Click to collapse
I did and it loads to Christians rom...
Please help...not sure if a moderator should move this to another thread or not
Shameless bump here. I still have not been able to resolve this. I can not seem to Hard SPL.
Answer:
I used the SSPL method from http://forum.xda-developers.com/showthread.php?t=431218 to finally get Hard SPL to work.
Hope this helps other people