Related
Hey everyone,
I am trying to flash a new rom (http://forum.xda-developers.com/showthread.php?t=418320), but I think I have run into a problem along the way. Please forgive me, but I am a very beginner at this stuff.
I was following the steps from this page (http://forum.xda-developers.com/showpost.php?p=2707841&postcount=4035). I have reached step 6, but in stead of a menu appearing, I only get the "loading..." on a gray screen appearing, and it has been like this for the last 15 minutes.
Any idea of what can be wrong? I have Olinex 1.30 Hard SPL.
Any help apprechiated.
Daniel
Need more info. What kind of device do you have? Are you trying to flash a GMS ROM on a CDMA device?
One more thing: what format is your internal storage. I'm not positive, but I think it has to be formatted as FAT32, and it comes as plain FAT. If you didn't reformat it, it might not be able to read your ROM file, and thus you won't be able to flash it that way. You'll have to use a Windows PC and try to flash it that way.
I have the Touch Diamond. I assume it is a CDMA device? I do not know what a GMS rom is really? Please forgive me if I have started something im really not qualified to do. After having read through several guides here, I assumed that flashing a ROM was pretty general as long as I stuck to the right device section?
Who is your phone carrier?
I have a windows PC (vista). However, I chose to follow the steps Suiller (post linked above) explained, as I got the impression it was safer (and faster).
My phone carrier is Network Norway. The phone was bought in Australia in october, but it is unlocked.
Ok, you have a GSM phone (that's the type of radio it uses). I believe you pointed to a GSM ROM, so it should be Ok.
It's probably the formatting. Can you still boot into the phone with the old ROM, or does it only go to the bootloader screen? If you can boot in, try formatting the internal memory (this will destroy all the data, so back it up). If that still doesn't work, try downloading another ROM file. That will let you know if you just got a bad copy of the ROM you want or if there is something wrong with the way you're trying to install it.
Thanks for your help!
Hello,
first of all I searched all around the internet, also here and found very contradicting informations, that's why I made this thread.
Since two days I'm proud owner of a German T-Mobile G1 (HTC Dream) and want to root it. However my phones information is as follows:
Firmware Version: 1.1
Baseband Version: 62.33.20.08U_1.22.12.29
Kenel Version: 2.6.25-01843-gfea26b0 [email protected] #6
Build Number: 123099
DREA110 PVT 32B
HBOOT-0.95.0000
CPLD-4
RADIO-1.22.12.29
Every tutorial I found mentioned RC Builds and that one would need different measures if the phone has a 123099 build. On one site I read that I need to make a so called Goldcard, on a different site someone recommend me to simply follow this guide:
http://forum.xda-developers.com/showthread.php?t=442480
Although this one also mentions RC builds and I also read a phone can easily full brick a phone due to mismatching SPL and Radio versions.
I'm new to Android and all this stuff so could anyone please tell me which guide I should follow?
Everyone here seems to be very knowledgeable so I figured this would be the best place to ask.
I'm only asking this much because this phone is a big financial burden for me and I don't want to full brick after a mere two days.
I have access to a Windows and Linux (Ubuntu) installation and a spare external Card Reader.
Thanks for any help in advance!
You need to follow the goldcard method. you can try to flash the RC7 image, but if it gives you the "Not Allowed" error, then you will need to use the goldcard method. The only difference between the two guides is how you downgrade the phone..
as per the SPL/radio incompatibility
you should flash the HardSPL as its safer than the haykuro (1.33.2005) spl
Make sure you update the Radio to 26I BEFORE you flash the haykuro spl. you have the old 29 radio so make sure you update. since you have a pvt board, as long as you update the radio before flashing the spl, you should be fine
Thanks for the reply!
I tried to flash the RC7 Image and got the "not allowed" error.
I wanted to flash the HardSPL anyway, but I guess I would need to do this after I downgraded my Firmware and gained root?
Also, could you maybe link me to a Goldcard tutorial that uses a method without a Windows Mobile Device?
http://forum.xda-developers.com/showthread.php?t=547557
Thank you!
No problem. If you need any help, you can pm me or respond here.
And to answer your other question, yes you will need root before you flash the HardSPL
You could probably use the one click method, but trust me, doing it the way in that will help you understand everything much better than you would by clicking one button. It makes a huge difference
Thanks, you're really helpful! I guess it's better to learn everything like you said^^'
I followed the Goldcard guide but I'm stuck at this step:
- go to the removable disk tab and select offset 00000000 till offset 00000170 go to "edit" and then past write.
- save it
- now copy dreaming.nbh to the root off your memorycard.(RC7) <-- RC7 works best for DREA110
I tried it with a 512mb SanDisk MicroSD and a 2GB SanDisk Micro SD but whenever I apply the HEX values from the goldcard.img to the SD Card and try to access it afterwards Windows 7 says that the Filesystem is damaged and cannot be accessed
so I can't put the image for flashing on it.
Any idea what I'm doing wrong? I use a generic USB Multi Card Reader and a MicroSD to SD adaptor to access my MicroSD cards, could that be the problem?
EDIT: Tried it with the G1 as a card reader and also with a requested Goldcard Image without changing the first 2 bytes to 00, no success....
well ive never created a goldcard so im not sure...but did you completely wipe the sd card and start over?
Yes, I full formatted the cards multiple times. Gotta try the Linux method now, any other suggestions would be greatly appriciated.
You can also try the one click method if your rom is compatible. making that goldcard is a hassle
Well I have a Goldcard now and completed these steps:
What To Do Now That You Have Root
Now that you have root, you will want to apply "Hard SPL" to your phone. HardSPL is what will allow you to apply flash images from other regions (like UK on US phones, and vice versa), create full backups of your phone, install the latest build from the Android source, and usually resurrect your phone if it is "bricked". You have already downloaded the file to your SD card, so now you can apply it.
1. Power off your phone.
2. Start up in recovery mode by holding home and pressing power.
3. You will now enter recovery mode. You should see an exclamation.
4. If you do not see a menu on screen, press Alt-L to show the menu.
5. Press Alt-S to apply the update from the SD card.
6. After the update is complete, hold Home and press Back to restart.
Click to expand...
Click to collapse
That means I have HardSPL and root now, right? So now I can flash a custom rom? If so, which one would you recommend me^^'
I heard of this Cyanogen ROM....
Oh and can I someway test if I really have Root and HardSPL?
Ya boot by holding Camera+Power
read back the HBOOT
if its anything but 0.95.0000, youve got a modded SPL.
also make sure you have 26I for the radio now as its necesary for a good signal for the cupcake and above builds.
If you want to flash cyanogen's rom, find the single update in the dev section by davidid or someone like that, and flash that just like another update.zip
if you can flash that, you have root (you can also verify by running adb and typing adb shell. if a # symbol comes up, your rooted)
i personally use cyanogen donut or mlign hero (but since you have hardspl, mlign wont work. You can update to the haykuro spl later, BUT BE VERY CAREFUL WHEN YOU DO. you could brick the phone, so read extensively before trying)
Well my screen looks now a whole lot different.
I now have three little Androids and the screen reads:
DREA110 PVT 32B
HSPL10.95. 3000
CPLD-4
RADIO-1.22.12.29
Oct 20 2008
Serial0
That means I have HardSPL and need to update my Radio, right?
If so can you link me to 26I Radio Image?
I will stay away from haykuro spl for now.
Also, could you link me to the best Cyanogen for my SPL?
Yeah I'm able to search myself but I'm scared of flashing something wrong....
Thanks in advance!
http://forum.xda-developers.com/showthread.php?t=569825
Theres the cyan update
Radio
http://developer.htc.com/adp.html#s3
Radio Image ota-radio-2_22_19_26I.zip 9181622 aeecdb49b74a0d4bb67f9d8af70c1889
Also, if you decide to flash haykuro.... make sure you flash the radio he provides
Alright thank you! I guess it doesn't matter if I take the Radio Link from Android 1.6 or 1.5? They both appear to be the same...
Second which do I need to install first, the Radio or Cyanogen?
Also, just to make sure, I download the radio update, rename it update.zip, boot into recovery and press ALT+S. Then I rename Cyanogen to update.zip and do the same again, right?
Finally, to have something awesome as this I would need Haykuro, right?
http://www.youtube.com/watch?v=PUNAc5E_UvQ
Hero looks so pretty but I'm afraid of bricking, is there an idiot proof guide to it?
Just wanted to say thanks to Breakthecycle2 from the T-Mobile forums I'm now running Mghty Max 1.9 quite well! Thanks for all the help here!
Hi all,
I’m in desperate need of some of your wealth of experience, i have managed to root and flash my g1 with - rc9 JFv1.51_CRB43-EU.zip (Jesus freke), and recovery-RA-dream-v1.6.2.img recovery image!. Now i want to update to a newer rom!
Now for the problem, the recovery program allows me to flash many of the rom's available but none of them work after the flash completes it just loads the g1 screen and stops there i have left it on that screen for about 10 min’s and nothing at all happens, but then it will allow me to flash back to rc9 JFv1.51_CRB43-EU.zip absolutely fine no issues every time?. Do i need to install anything else before updating to Open Eclare 2.1.1 or SuperD1103-blk.? I’m in the UK with a UK g1 mobile if that makes a difference?
crusader0071 said:
Now for the problem, the recovery program allows me to flash many of the rom's available but none of them work after the flash completes it just loads the g1 screen and stops there i have left it on that screen for about 10 min’s and nothing at all happens, but then it will allow me to flash back to rc9 JFv1.51_CRB43-EU.zip absolutely fine no issues every time?.
Click to expand...
Click to collapse
Just use the top three wipes available in Anon's recovery menu: Wipe System/Data (1st), Davilk Cache (2nd), Ext Partition (3rd). If you haven't partitioned your SD card into FAT32, Ext2, 3, or 4 and Linux-Swap, do so now with the Recovery menu. You must backup your fat32 first, because a total repartition will totally blank your data. Good luck!
crusader0071 said:
Hi all,
I’m in desperate need of some of your wealth of experience, i have managed to root and flash my g1 with - rc9 JFv1.51_CRB43-EU.zip (Jesus freke), and recovery-RA-dream-v1.6.2.img recovery image!. Now i want to update to a newer rom!
Now for the problem, the recovery program allows me to flash many of the rom's available but none of them work after the flash completes it just loads the g1 screen and stops there i have left it on that screen for about 10 min’s and nothing at all happens, but then it will allow me to flash back to rc9 JFv1.51_CRB43-EU.zip absolutely fine no issues every time?. Do i need to install anything else before updating to Open Eclare 2.1.1 or SuperD1103-blk.? I’m in the UK with a UK g1 mobile if that makes a difference?
Click to expand...
Click to collapse
Make sure you partition your sd card and then try like the above said....or maybe try flashing death spl.
http://forum.xda-developers.com/showthread.php?t=625886&highlight=Death
thanks for trying to help but....
hi thanks for your help but ...
i have partitioned the card via anons recovery flasher, i have set my 8gb to 96mb swap , 1.5gb ext2 and the rest is used for fat32.
i have also gone throught the menu and deleted / erased the top 3 as requested but when i install a new rom it still freezes on the g1 welcome screen? please help!
G1ForFun said:
Make sure you partition your sd card and then try like the above said....or maybe try flashing death spl.
http://forum.xda-developers.com/showthread.php?t=625886&highlight=Death
Click to expand...
Click to collapse
hi i just noticed im using Hard Spl update at the moment ? how do i update to Haykuro?
i think i have totaly broke my phone? - i downloaded haykuros spl and flashed it via the anons recovers flash image from sd card, and now i can no longer get in to the recover menu? and no fast boot please please help me !
crusader0071 said:
i think i have totaly broke my phone? - i downloaded haykuros spl and flashed it via the anons recovers flash image from sd card, and now i can no longer get in to the recover menu? and no fast boot please please help me !
Click to expand...
Click to collapse
This is YOUR FAULT for NOT READING!!!!
You installed an SPL meant for an HTC MAGIC onto your HTC DREAM. It *CAN* be made to work, HOWEVER, you failed to read and understand what is required to actually do it safely.
SPECIFICALLY, you are stuck in boot mode 3 -- boot to recovery, and because you changed the SPL, your recovery partition is UNABLE TO BOOT.
You are BRICKED, and the only way out is to use a hardware interface called "JTAG", which requires you to disassemble the phone.
SPECIFICALLY:
You missed the part of that thread that says "MOD EDIT PLEASE READ THIS THREAD FOR UP TO DATE INFORMATION".
I have no sympathy for you. That instruction is in big purple letters.
hi thanks for your info, do you know anyone or anywhere i can get my phone jtagged?
How could you mess it up with step by step instructions....lol...I am being dead serious....it doesn't get more clear than this.
IMPORTANT: Before going any further make sure that you have PVT board. You can do this by rebooting your phone and holding the camera button. The first line should say "PVT" if you see "DVT" then DO NOT flash this because odds are you will get a brick but If it says "PVT" then you are good to go.
First you are going to need to download the latest radio and the SPL. both can be found here http://code.google.com/p/sapphire-port-dream/ There is also a new radio that is compatible that can be found here http://forum.xda-developers.com/showthread.php?t=640535
Prior to starting the installation process please make sure that your battery has a good charge. Also DO NOT pull your battery out at anytime during the installation process. I know it seems like common sense but I read a thread where someone had pulled their battery in the middle of the installation process and they ended up with a brick.
Now that all that's out of the way lets get started!
1. Copy "ota-radio-2_22_19_26I.zip" or "G1-radio-2_22_23_02.zip" and "spl-signed.zip" onto the root of your SD card.
2. Reboot into recovery. I suggest using the RA-dream recovery you can download it here http://forum.xda-developers.com/showthread.php?t=566669
3. Wipe your phone "factory data reset" (this step isnt really necessary since your phone is wiped after flashing the SPL but I always like to wipe before flashing anything)
DO NOT SKIP THIS NEXT STEP OR YOU WILL BRICK YOUR PHONE
You must have the latest radio "2_22_19_26I" or "2_22_23_02" to flash this SPL if you already have the latest radio you should not have to flash it again but it will not hurt if you do flash it again. When in doubt flash it anyway.
4. Flash the Radio "ota-radio-2_22_19_26I.zip" or "G1-radio-2_22_23_02.zip" it will install and then it will ask you to reboot to finish the installation, so reboot, it will then finish installing and then reboot back into recovery.
5. Flash the SPL "spl-signed.zip" it will install and then ask you to reboot to finish the installation, so reboot, it will then finish installing and reboot into recovery so you can flash your ROM
i cant get in to fast boot or recovery i just get the g1 screen, if i press camera and power or if i press home and power i just get the g1 nothing else
crusader0071 said:
i cant get in to fast boot or recovery i just get the g1 screen, if i press camera and power or if i press home and power i just get the g1 nothing else
Click to expand...
Click to collapse
Did you follow those steps when flashing the SPL? Did you even flash the radio before flashing the SPL?
It sounds like you have no idea what you did to your phone which is never a good sign (and usually means you shouldn't even be flashing custom radios/spl's/roms)
no i did not, i was asking for help for the last 2 or 3 days? i did what i thought was right but it was not. can i fix it or not?
heres what you do
ive did this too lmao jus go here www*androidhustler*blogspot*com ( THE * ARE REPLACEMENTS FOR . BECAUSE I CANT POST A OUTSIDE LINK SO U GET WUT IM SAYING SWITCH THE * WITH A . ) THEN SCROLL DWN TO A POST CALLED THE 2010 HOW TO GET CYANOGEN LATEST. DO ALL STEPS AND DONT RUSH. IF YOURE G1 DOESNT BOOT UP PROPERLY THEN I QUIT THIS SHYT BRO. LOL FOR REAL AND IF U HAVE ANY QUESTION EMAIL ME AT [email protected]*COM
crusader0071 said:
no i did not, i was asking for help for the last 2 or 3 days? i did what i thought was right but it was not. can i fix it or not?
Click to expand...
Click to collapse
Sigh....I would go buy another phone off Craigslist or something similar.
Next time...please read before flashing....Although I'm sure you will after the last mishap.
the only way to fix your phone is to buy a doner phone with a broken screen or something cheap off of ebay
there is NO KNOWN WAY to fix it without a doner (the jtag method isnt do-able yet)
I know here in town...there are so many G1's up for sale around the $150 mark in really really nice condition.
That's where I'd be looking if I bricked my G1. Well...I'd be replacing it with a HD2 probably...lol
garok89 said:
the only way to fix your phone is to buy a doner phone with a broken screen or something cheap off of ebay
there is NO KNOWN WAY to fix it without a doner (the jtag method isnt do-able yet)
Click to expand...
Click to collapse
What do you mean by jtag method isn't do-able?
ezterry did mine without an issue.
details
Sleeepy2 said:
What do you mean by jtag method isn't do-able?
ezterry did mine without an issue.
Click to expand...
Click to collapse
have you got contact details for ezterry? if so pm me please.
as far as i can see the jtag is still in testing?
This noob is in the UK anyways. Let him figure it out.
Wrong section, soft bricked his own phone and freaking out.
Please READ. You are from the UK so your English isn't bad. You have no excuse for not following instructions.
Ways to fix your phone:
1) motherboard replacement
2) JTAG (experts are not anywhere near you though)
3) buy a new phone
Mods please get this out of here
Okay, so a few years ago I successfully rooted my boyfriend's G1 and swore never again to go anywhere near the process.
However, said phone has now been given to my boyfriend's dad, and he's managed to install a couple of custom roms. In the last week though, he's totally screwed it up. Didn't seem to follow any sort of backing up process, or can even tell me what tutorial he was following to get it in this state.
The phone hangs at the splash screen. I can get into fastboot/hboot but there are only a few options available.
SPL is 1.33.0006 which I can gather is bad from my reading.
Hboot info is:
Dream PVT 32B Ship S-on
Hboot - 1.33.0006 (Dream11000)
CPLD-4
Radio-2.22.19.261
I have tried:
Initially I just tried going into recovery mode (I think that's what it's called - home & power) and wiping the data to see if that stopped the screen hanging. It didn't.
Putting rc7 dreamimg.nbh on the phone and loading via hboot/fastboot. When I do this it fails saying 'Main version is older.'
After doing some searching, I see someone mentioned this would mean you need to use the goldcard method. I vaguely remember having to do this a few years back on the phone when I rooted it the first time.
I go through the process, following an unlockr tutorial (can't post the link - sorry).
However, I get the same response through fastboot - 'main version is older'.
At this point I decided to try flashing a recovery image via the adb. Go through the process of installing everything etc. but when it came to installing the usb drivers for the phone, it failed although it did install the htc bootloader. I checked using adb devices command to see if it was picking anything up and it was however, when I go into the command prompt and try to do anything I just get a <remote: not allow> message.
It's only after I look for <remote: not allow> message error that I understand that 1.33.0006 is a 'perfect' SPL, and explains why I can't really do anything.
I really didn't want to resort to forum posting (one of the reasons I swore never to go near the G1 again after rooting was because I *know* I'm not tech savvy enough to be messing around with this stuff), but after spending around 6 hours over two days on this I'm absolutely stumped. The problem is, I'm stubborn so I hate to give up after spending so much time on the stupid thing (bye bye flexi day), so if anyone has any suggestions, or if they could just tell me it's a lost cause then it might help.
Thanks for your time...
do you have the UK version of phone or the US version?
can you get into recovery?
Sorry, it's the UK version - I can get into recovery (if that's home and power ?) I think. Thanks.
What nbh file was flashed prior to this? (almost sounds like the states someone was in after flashing the sappimg on a dream with 1.33.0013d..
Well first thing is to make a gold card if you don't already have one.. Then we can try one of two things. (you can make it on another phone, its a property of the sd card not the phone)
1) (may have the same main version is older problem but easy if it works) place the Orange nbh:
orange-1.58.73.2.nbh (MD5: aca4dee0c1ece7e9773f2ecbdfbba7c0)
onto the root of the goldcard named DREAIMG.nbh
If this works (or at least flashes the s=off SPL) you are in the clear simply use fastboot to re-install the 2708+ recovery/radio/spl then install a rom as per here
2) If option 1 failed... well this is an annoying process.. and risky if you take shortcuts so don't ..
A -- This time put the rogers e911 patched nbh rogers_1.89.631.1.nbh MD5:25bfcc329679e4869b3d65f673e463ac
onto the root of the goldcard named DREAIMG.nbh
This is the larges "main version number" in an official nbh for the Dream we have.
If that fails to flash (try again) if it still fails.. well I'm not sure what to do if both boot/recovery are failing (short of jtag anyway)
B -- If it succeeded you now (despite any labels on your phone) have a rogers dream.. (I mention this because working with an ebi1 radio is a bit different than the ebi0 and you don't want to brick your phone)
Ok next step is re-root: http://forum.xda-developers.com/wiki/index.php?title=Rooting_HTC_Branded_EBI1_Dreams
(Sections A-D inclusive)
C -- Before installing a rom.. now that an eng SPL is installed you can use fastboot (and only fastboot with the 3.22 radio) to install the 2708 radio and thus have a more commonly supported system:
per Follow this 2708+ install
remember do not install a 2.22 radio via recovery while a 3.22 radio is installed you will brick your phone
--
Best of luck.. really sounds like something happened that ought not have.
Thank you!
Option 1 didn't work - I still got the 'main title is older' message.
However, option 2 (after a small wobble) worked! First time I tried it, it failed stating 'partition update fail!' but after a reboot (which showed the rogers logo - a change from before) and a retry, it worked! I followed the rest of the provided instructions and installed the BIFFMOD V2.1-EZTerry 2708 port and all is well!
Thank you so much again for your help, it really is appreciated. I would not have been able to do this without your help - I've sent a small donation through as a token of thanks.
I've learnt more about G1s than I ever wanted to know, but thanks to you (and the information provided by the XDA community) it wasn't all wasted time!
I bought my G1 on the first day I could. I rooted it as soon as you could so I could get apps to SD and bump up the CPU a bit. I loved this phone. I eventually upgraded to an HD2 so I could run Android on it and stick with T-Mobile. I just booted my G1 back up so that I could install some apps to use it as a remote webcam. I did a factory reset and then got stuck during the activation screen. I know you can use ADB to bypass this but I figured I might as well just install a new rom on it that can activate the wifi during the startup process.
This is where I feel lost. I haven't booted up my G1 in ages and thus I haven't flashed it in ages. I would like to install this rom: The Official "KANGED" CM7 for DS ... but I don't have the correct SPL or Radio I am guessing. I currently have HBOOT-1.33.2005 and Radio 2.22.19.26I. I have a recovery image installed (RA-dream-v1.6.2) so I can flash roms and radios and such but I am having trouble finding threads that talk about the proper files to install. If somebody could just point me in the right direction I would appreciate it. Thanks!!
http://forum.xda-developers.com/showthread.php?t=831139
this will have all the needed info
so to clarify - via fastboot update recovery then radio then spl
when finished download rom and gapps
congrats your done!
Well, there's also a way to flash these RADIO and SPL, shown by YOU (demkantor) but as he said, fastboot is a little bit more complicated for me, but if you have it , just use fastboot. And remember, 'Fastboot is your Friend' !!!