[Q] Issues with a little car wax? - A7 Accessories

Like most devices my A7 is a finger print magnet.
I like to experiment. Are there any issues with a light coat of a good car wax on the face plate. Not the cleaning kind just pure car wax?
Comments
Thanks

Results
I've used a light coat of pure care wax and wiped the faceplate off with a microfiber cloth.
It seems to cut down on the finger prints. When they eventually start to show up they wipe off very easily.
So I thing that it is a safe practice and seems to make the screen more user friendly.
Just my opinion.

Related

NC : Screen Surface: Sexy Silky Glass/Diy

Warning!!!!!!!! You really can crack your glass by following the directions below, Please, read no further and leave now. If you, crack your screen, set your house on fire, or sever an artery (broken glass) then bleed out and die......well, you were warned!!!!!!!!!!!!!!
Okay, if your still here, read on and good luck.
Samsung Galaxy S Screens are smooth and silky! Even the name, gorilla - tough and glass- vulnerable, says sex;
Well, how can we get a sexy Fay Wray G.Tab screen surface from a humble sandpapered plain Jane surfaced NC screen?
The secret is............RAINX.....That's right, the same stuff you want on your windshield in a downpour, will with proper application, impart that silky smoothness you secretly crave.
APPLICATION:
1. Use "The original" rainX. (Caution: it is flammable)
2. Clean glass surface really, really...no really good. (Remove oils, alcohol works)
3. Use clean paper towels, fold into squares (4 or 5 )
4. Dampen towel applicator and scrub surface (Don't Crack Your Screen! Work into micropores of glass surface)
5. Dry to haze (for humidity over 10% use a blow dryer...low heat!)
6. Polish methodically...lots of clean dry paper towels (Don't Crack Your Screen!)
7. REPEAT (It took me 3 times)
Warning!!!!!! Do not, I repeat, Do not allow your girl/boy/wife/husband to touch the new silky surface; not if you ever want either of them back, that is.
Thanks for posting. Just a couple questions...
First, does this prevent finger oils from messing up the screen?
Next, wouldn't windex/alcohol remove the rainx then next time you cleaned your screen? It does on windshields... If so (and if it doesn't prevent finger grease marks), then I think you'd have to do this process over and over, each time you cleaned your screen.
Bimboy said:
Thanks for posting. Just a couple questions...
First, does this prevent finger oils from messing up the screen?
Next, wouldn't windex/alcohol remove the rainx then next time you cleaned your screen? It does on windshields... If so (and if it doesn't prevent finger grease marks), then I think you'd have to do this process over and over, each time you cleaned your screen.
Click to expand...
Click to collapse
Why are u using windex or alcohol? Just use a micro fiber cloth. No chemicals.
Uh, yeah, I wouldn't advise using Windex or alcohol on any screen. If a simple microfiber cloth won't clean it, add a drop of water for the tough stuff.
or just use tv cleaners
RainX application maintenance
WFINGER
Bimboy said:
Thanks for posting. Just a couple questions...
First, does this prevent finger oils from messing up the screen?
Next, wouldn't windex/alcohol remove the rainx then next time you cleaned your screen? It does on windshields... If so (and if it doesn't prevent finger grease marks), then I think you'd have to do this process over and over, each time you cleaned your screen.
Click to expand...
Click to collapse
Finland_2_Cupertino said:
Why are u using windex or alcohol? Just use a micro fiber cloth. No chemicals.
Click to expand...
Click to collapse
Bimboy, yes it does help with the finger oils. I think it works by preventing the oils from settling into the glass micropores. You still get smugdes and fingerprints but they wipe off much, much easier.
As Finland 2 suggested, once applied, a microfiber cloth is all that is needed to maintain the new finish. I expect it to last quite a while, since on a windsheild even with wipers and rain, an application usually. Lasts up to a month.
A little spritz of Stoner Invisible Glass (for autos) on a microfiber cloth does a good job getting the NC glass as smooth as a Tab too. Fights fingerprints for a bit, and doesn't take any effort. A can should last you a lifetime.
Pledge furniture polish spray will also help (it's pretty popular for cleaning helmet visors and motorcycle windscreens) and will also keep the prints down on the plastic bezel area (and back). Once again, apply it to a cloth first, don't spray it directly on the NC.
O your can just get a nice Screen protector like the AntiGlare one B&N Sell..........
Makes my screen silky smooth and protects it from scratches.... Why would I want to waste time using rainx and a process that could hurt the screen?
Also Rubbing alcohol with Microfiber Cloth Works Great to clean the screen, gets ride of all the oil and grim. Do not use anything but a Microfiber Cloth(As it could scratch the screen), Also Pure alcohol wont hurt the screen, its Ammonium based products and harsher Chemicals like that you need to watch out for. Alcohol is a prove safe method for cleaning Plastics even Internal Computer parts wont be hurt by Rubbing Alcohol.
I use to by screen protectors for all phones back when they had the plastic resistive screens. So far I have yet to scratch any of my glass capacitive ones. I did buy a used ipad from someone that managed to scratch the glass, it can barely be seen but it is there. So I'm on the fence about a screen protector for the nook. I probably won't get one for the nook but if i buy a $500+ tablet you can bet I will put one on.
I don't like the drag created when using a Zagg (invisible sheild) soft films but I don't mind the harder plastic ones that you occasionally have to replace.
gedster314 said:
I use to by screen protectors for all phones back when they had the plastic resistive screens. So far I have yet to scratch any of my glass capacitive ones. I did buy a used ipad from someone that managed to scratch the glass, it can barely be seen but it is there. So I'm on the fence about a screen protector for the nook. I probably won't get one for the nook but if i buy a $500+ tablet you can bet I will put one on.
I don't like the drag created when using a Zagg (invisible sheild) soft films but I don't mind the harder plastic ones that you occasionally have to replace.
Click to expand...
Click to collapse
I'm kinda in your camp, I've never found a screen protector that I wanted to use. They may be out there, but the trade offs, for me at least, seem to out weight the advantages in day to day use. Since I use a cover for my NC, I don't have to worry about objects in my pocket, keys and such, gouging my screen.
I know the RainX thing isn't for every one, and there may be easier ways to achieve the smooth surface effect, but I have found it to have worked very well. Before treating the screen, it would take a lot more microfiber polishing to remove finger oils or smudges, but now they come off very easily.
I've been using 'Gel Gloss No-Streek' for years on all kinds of glass stuff. It really is the best that I've found and it is pretty cheap. I used it on my nC and it is 'silky smooth' and resists fingerprints extremely well. One word of note though is that the polish does contain 'petroleum distillates and ammonia' so you have to be careful handling it and it stinks. Also, like most good quality polish you want to apply it to a cloth first, then to the nC, don't apply directly to the nC.
Here is a link to the stuff I bought.
http://www.amazon.com/Industries-NS-8-8OZ-Glass-Polish/dp/B000IO8GWC
Matte Anti-glare screen filter is the way to go
gedster314 said:
I use to by screen protectors for all phones back when they had the plastic resistive screens. So far I have yet to scratch any of my glass capacitive ones. I did buy a used ipad from someone that managed to scratch the glass, it can barely be seen but it is there. So I'm on the fence about a screen protector for the nook. I probably won't get one for the nook but if i buy a $500+ tablet you can bet I will put one on.
I don't like the drag created when using a Zagg (invisible sheild) soft films but I don't mind the harder plastic ones that you occasionally have to replace.
Click to expand...
Click to collapse
I feel ya. I think you would be presently surprised with the Nook AntiGlare Matte filter available at Barnes and Noble. It's $15 and really does make the screen feel smooth, while at the same time resisting finger prints and smudges really well. A night and day improvement over the oddly tacky feel of the nook color screen. They give you two of them. Oh, and it's the "hard" type of plastic, not the flimsy cheap stuff.
RainX is not going to keep your screen from getting scratched. It also will probably increase and not reduce glare.
Gel gloss, isnt that for fiber glass?
Sent from my SAMSUNG-SGH-I897 using XDA App

Who did NOT put on a screen protector?

I haven't put one on mine (yet). I have a case that does cover the screen, but who knows something will slide in between and rub up against the screen.
That being said, who HASN'T put on a screen protector and doesn't plan to? I'm kind of against them because not only do I struggle with putting them on, I always find some imperfections (which drives me bonkers).
Just got mine two days ago. Rooted it. Loaded apps. Lovin it and finally, to get to your question, no I have not and don't plan on getting one. Never use them on phones so I don't plan on starting. I really don't think they are needed and I also think they degrade the screen performance. I could be wrong but JMO.
I haven't put one on, have thought about it but since I got my case haven't found the need. I just give it a good wipe of my microfiber cloth once in a while.
I bought some, but putting it on became quite a hassle. I touched the sticky side of one putting a nice fingerprint on it (arg), and I can NEVER get all of the dust / air-bubbles out, so it ends up just driving me nuts.
I ended up trashing them.
If you buy the screen protectors at a B&N store, they will install for you at no extra charge. Plus you get a microfiber cloth. I haven't noticed any degrade in screen performance.
I put the anti-glare screen protector on the day I got my NC. I've been happy with it and the anti-glare version goes on incrediblincredibly easy as it's a bit thicker than the regular kind. Just thought I'd share for those of you who want one but hate putting them on.
MkFly said:
I bought some, but putting it on became quite a hassle. I touched the sticky side of one putting a nice fingerprint on it (arg), and I can NEVER get all of the dust / air-bubbles out, so it ends up just driving me nuts.
I ended up trashing them.
Click to expand...
Click to collapse
I did the exact same thing.
I did not have one on mine as I plan on trying to exchange it again, but I bought a screen protector for a laptop from $5 Below and cut it to fit..
Works nicely
While I know B&N would put one on for me, I have other things to spend the $15 (or so) dollars on. Plus there's no guarantee the person there will install it to meet my OCDness.
I haven't and i don't plan to.
Sent from my nook COLOR.
swest6602 said:
I put the anti-glare screen protector on the day I got my NC. I've been happy with it and the anti-glare version goes on incrediblincredibly easy as it's a bit thicker than the regular kind. Just thought I'd share for those of you who want one but hate putting them on.
Click to expand...
Click to collapse
Same here, I put mine on about 15 minutes after opening it. Haven't had any problems. I used the water/baby shampoo spray with it that came with my BodyGaurdz for my phone and it went on without any problems. Within 20 minutes all the water was gone and the protector wasn't even noticeable
MkFly said:
I bought some, but putting it on became quite a hassle. I touched the sticky side of one putting a nice fingerprint on it (arg), and I can NEVER get all of the dust / air-bubbles out, so it ends up just driving me nuts.
I ended up trashing them.
Click to expand...
Click to collapse
I feel that Im pretty good at putting them on. I use the dry install type like Realook for all my phones and the B&N anti glare for the NC. This is what I do if you ever want to give it a try. Make sure everything is laid out and ready. Turns fans off if your room has one, close windows, etc..
Wash your hands throughly, important that all oil comes off
Spray the air with some sort of cleaner. My favorite is Monster Cable LCD TV cleaner
Clean the device with cleaner and microfiber cloth
Spray air again around your area you are working, wait a few secs for it to fall from air
Remove a very small portion of the backing enough to line up the entire bottom edge of protector
with protector lined up, use a credit card or squeegee to push protector on while backing automatically comes off all the way up.
this leaves minimal bubble and works for me almost every single time. your hands really never touch any sticky side and when you slide the squeegee up it automatically removes the backing for you. I have yet to trash a protector and have to get another. if you have dust, then carefully pull back and use a toothpick to get the dust particle off and reapply. Hope this helps someone.
HotShotAzn said:
While I know B&N would put one on for me, I have other things to spend the $15 (or so) dollars on. Plus there's no guarantee the person there will install it to meet my OCDness.
Click to expand...
Click to collapse
I second that OCDness!
Sent from my rooted NookColor using XDA app
i bought this tablet over other comparable android tabs (gtab, archos, etc) due to its beautiful screen. no way im putting a screen protector over it. i use one on my phone, but only because it travels in my pocket.
I bought the anti-glare protector from B&N. I used a microfiber cloth thing that came with this windshield cleaning kit I got for Christmas to clean the screen and went over it a few times with the supplied cloth to remove dust. I was able to apply the protector without trapping a single air bubble, piece of lint, fingerprint or anything else. While it hasn't done much for reducing glare, it has helped tremendously with fingerprint grease and in reducing the friction between my finger and the screen.
Sent from my NookColor via the XDA app.
t140568 said:
I bought the anti-glare protector from B&N. I used a microfiber cloth thing that came with this windshield cleaning kit I got for Christmas to clean the screen and went over it a few times with the supplied cloth to remove dust. I was able to apply the protector without trapping a single air bubble, piece of lint, fingerprint or anything else. While it hasn't done much for reducing glare, it has helped tremendously with fingerprint grease and in reducing the friction between my finger and the screen.
Sent from my NookColor via the XDA app.
Click to expand...
Click to collapse
This sums up my experience as well. It's worth it just for the fingerprint protection.
techboydino said:
I feel that Im pretty good at putting them on. I use the dry install type like Realook for all my phones and the B&N anti glare for the NC. This is what I do if you ever want to give it a try. Make sure everything is laid out and ready. Turns fans off if your room has one, close windows, etc..
Wash your hands throughly, important that all oil comes off
Spray the air with some sort of cleaner. My favorite is Monster Cable LCD TV cleaner
Clean the device with cleaner and microfiber cloth
Spray air again around your area you are working, wait a few secs for it to fall from air
Remove a very small portion of the backing enough to line up the entire bottom edge of protector
with protector lined up, use a credit card or squeegee to push protector on while backing automatically comes off all the way up.
this leaves minimal bubble and works for me almost every single time. your hands really never touch any sticky side and when you slide the squeegee up it automatically removes the backing for you. I have yet to trash a protector and have to get another. if you have dust, then carefully pull back and use a toothpick to get the dust particle off and reapply. Hope this helps someone.
Click to expand...
Click to collapse
I have learned that going in the bathroom, turning on the shower and allowing the steam to take the dust out of the air is the only way to ensure that there are no air bubbles.
I also have nearby some scotch tape so that if there is a speck of dust or lint, I can apply the tap to the sticky side of the screen protector without getting my fingerprints all over it.
techboydino said:
I feel that Im pretty good at putting them on. I use the dry install type like Realook for all my phones and the B&N anti glare for the NC. This is what I do if you ever want to give it a try. Make sure everything is laid out and ready. Turns fans off if your room has one, close windows, etc..
Wash your hands throughly, important that all oil comes off
Spray the air with some sort of cleaner. My favorite is Monster Cable LCD TV cleaner
Clean the device with cleaner and microfiber cloth
Spray air again around your area you are working, wait a few secs for it to fall from air
Remove a very small portion of the backing enough to line up the entire bottom edge of protector
with protector lined up, use a credit card or squeegee to push protector on while backing automatically comes off all the way up.
this leaves minimal bubble and works for me almost every single time. your hands really never touch any sticky side and when you slide the squeegee up it automatically removes the backing for you. I have yet to trash a protector and have to get another. if you have dust, then carefully pull back and use a toothpick to get the dust particle off and reapply. Hope this helps someone.
Click to expand...
Click to collapse
Thanks, I think I might have to have another go at it.
Been naked on 4 previous smart phones. Currently naked on DroidX, Viewsonic Gtab and Nook color. Haven't had any problems with any of the devices.
My phones i usually put one on there because i put it in and out of pocket but Nook color is also naked for me besides a Hard case snap cover I got off eBay.

Doing Dry Install Screen protectors in a steamy bathroom

Can it be done? Should it? I ask because, since it's steamy, there will obviously be some moisture underneath the screen protector.
Thanks in advance.
Taken from the Screen Protectors thread
AirBruce said:
First off, I've tried a few screen protectors in my time. And to be candid, most of them have sucked. The last one I used, was one from bodyguards on my iPhone 4 (which worked less than stellar). When I switched over to the Android platform on the Epic 4g Touch, I went naked and just used the reg. screen. (Luckily just a few minor scratches from going naked, but nothing earth shattering.)
So quick background on ordering. I ordered Just Like Glass (JLG) on Cyber Monday, it got to my office in NYC on Friday Dec. 7th. And to add to the delay, unfortunately the mail room at my company failed to deliver mail to my dept on that day, and I had to wait the weekend until Monday the 10th. When I finally did recieve it, it came in a box and was nice and intact. (I placed photo's in this forum of the packaging for others to see. Just look it up on the thread to see how it arrives. I uploaded photo's of the packaging, and what to expect inside the packaging)
So I got it and took it home, and this is what I would recommend to all who receive this. And please follow these steps, they will help tremendously. It's going to sound crazy, but it really does work. Please take it into the bathroom with you (screen protector and your phone) and take a nice hot shower. (WITHOUT THE PHONE OR PROTECTOR OBVIOUSLY) Why do you want to do this? Because the steam will bond with dust particles and they will fall to the ground. You really want a nice and dust free room so you don't get any stuck between the screen and screen protect when you apply it.
Before jumping in the shower and getting down to the applying process, it is VERY important to familiarize yourself with the JLG screen protector. While it is still on it's protective sheet, just place it over the Note 2 screen to see and learn of how it will fit. Look and learn at how much space should be left on the top and bottom. All this is estimating and learning on how it's going to be placed before you get down to the nitty gritty is very important, and will prove to be invaluable for when you actually apply JLG.
After showering and drying off (and hopefully getting somewhat dressed) make sure you power off the phone, and you thoroughly clean it as well. (More than anything, clean the screen with the attached cloth.) You will see some moisture droplets appear on the screen due to the steam in the room, but it's ok. Just make sure you clean it very VERY well with the provided cloth. (DO NOT USE KLEENEX, OR A TOWEL, USE THE PROVIDED CLOTH) Why the provided cloth? Because it will not leave behind lint. It's just as bad as dust particles, and that is enemy #1 for applying a screen protector.
Next, make sure you have a cup or bowl of water next to you. (I used a bowl) and make sure you fill it up with water. Make sure you run the bathroom sink water for a while so you don't get any contaminants in it, so you can get it to as close to clean as possible. Then make sure you wash your hands with soap and water. Make sure you wash your hands well (even though you just showered and dried off) and after washing them, DO NOT DRY THEM! Just shake off the excess water. (Why not dry? Because you need your hands wet to handle the protector and it doesn't stick to your fingers, and also so you don't contaminate the applicator side of the protector with any contaminants from whatever you used to dry your hands.)
So after your done shaking off excess water from your hands, grab the JLG screen protector, and peel it entirely off the sheet it comes on. Grab the spray bottle that is provided and spray 3-4 full sprays on the sticky side of the screen protector. (Now the next part might seem counterproductive but it is important!) Make sure that you use your index finger and you spread the sprayed liquid over the sticky portion side of the JGL screen protector. Why is this important? Because you want the liquid to be evenly spread. Don't worry about contaminants ruining your future viewing experience. If you've followed these directions correctly, you've maintained as close to a "sterile" room/method as possible, and there should be no future contaminants on the applicator side of the JLG screen protector and your Note 2 screen.
Now while doing all this, make sure your hands stay nice and wet. Remember to use the cup or bowl next to you to keep your hands wet.
Next, using your index finger, do a sweeping motion of the sticky side of the JLG screen protector, to remove excess fluid. (Just one pass, you still need it semi wet) This will help with in having some leeway in mildly moving the screen protector on the Note 2 screen after applying. (More on this in a second)
After, (using both hands) grab the JLG screen protector from the top and bottom with your index and thumb, (with the sticky side down) and slowly and carefully lower the JLG Screen protector into place on the Note 2. Now, if you remember from what I said at the top, you should remember your testing of how and where it should have been placed as I stated in the beginning on where it should fit.
If done correctly, you will create a pocket of liquid between the protector and the note 2 screen, which will give you a little bit of latitude in moving it around just enough to place correctly. Once you are happy with the placement of the JLG screen protector, you can now slowly and delicately start to squeeze out the water that has created the little pocket of liquid between the two. Use a credit card or drivers license. (I used my credit card) Use it as a squeegee in "ironing" out the liquid between the two. I recommend from the center, to the top, and center to bottom. Keep going slow, using a little bit of force. While the liquid is squeezing out, make sure you use the provided cloth and absorb the liquid so that it doesn't get into the spaces between the home button or ear speaker holes. Go slowly.
After you have gotten most of the liquid out from under the JLG screen protector, still be careful with it. It may shift or move, and if that happens, your screwed.
Exit your bathroom, and you can now power up the phone. You can leave the phone on, but I highly recommend that you use it lightly if not at all over night. This will give the screen protector time to somewhat bond to the note 2's screen.
Once you wake up in the morning, you will see pockets of liquid and bubbles under the screen protector. Here you can do 1 of 2 things. You can either A) let the pockets dry out. (It will eventually, but it'll take a long time, like 7-10 days). Or you can (and I recommend you do this) B) Carefully squeeze out the liquid pockets from between the Note 2 and JLG screen protector. You're going to have to use a bit of force, because it's as if your steam rolling out the liquid. Just use your common sense, and push out the excess liquid pockets with your thumb. You can try to use a credit card, but found this works poorly, it's best to just use your thumb and force it out.
I recommend you squeeze out the pockets because if you don't, it's going to take 2-3 times longer for it to dry if you don't. Just do it without breaking your phone screen please. During this time, in the days following, you should be A-okay in using your phone, as well as the stylus, without having to fear of the JLG screen protector shifting.
Finally, after waiting a few days (it took 5 in my case) the screen protector should be dry.
So what do I think of it? I think it's incredibly better than ANY screen protector film you can get from Bodyguards or even Zagg Invisibleshield. Those were awful in the sense that when you used the stylus, it would leave imprints on the cheap plastic film. And those imprints are permanent. And god forbid you ever left something with a sharp point near or on top of it for more than 2 seconds. The imprints are almost certainly becoming permanent.
As for JLG, it doesn't work that way. It's so strong it doesn't leave imprints. And as for using the stylus it glides right over the protector. Now, the big question, Does it work just like glass? The answer, is a big 95% yes! It is not 100% just like glass, but it is very VERY close to it. In my humble opinion it is not better than glass, or 100% jus like it, but it is very VERY close to the stock glass on the Note 2 screen.
I state that this product is the best one on the market, and after curing completely, you will be VERY happy with it.
Some complaints I do have about it are this though. I wish it did cover the screen just a little more. About .5 mm in each direction. Is it REALLY necessary? I would say only if you're OCD. I think the cut is fine the way it is, but .5 mm in each direction would be perfect. (I'm not saying Scott should resize it, just saying though)
The next one is the "rainbow effect." What is this? After applying JGL, and it has cured (dried completely) you will notice a wavy/rainbow effect of lines that run vertically. It is not noticeable when the screen is on, but it is noticeable if you turn off the screen and hold up the phone at certain angles. If you can't find it at first, that's fine, you need a certain type of lighting condition and angle to see it, but it's there. Is this a rule breaker? Not really, I mean unless your OCD again, this isn't really a big deal, and for the most part (about 95%), is hardly noticeable.
The last complaint I have is the drying time. Depending on how much liquid you squeegee out, and how many pockets of liquid you steamroll out after, it can take a while for this to dry. When I used bodyguardz or zagg's, it would take about 2-3 days. This one took 2-3 times as long.
Lastly, I just wanted to add that Scott the CEO is great. I emailed him after my package never arrived due to it being tardy, and he wrote back to me to inform me of my package's tracking number in less than 24hrs. Honestly, this is great customer service, and I wish more CEO's out there would act like him. If you look at this lengthy XDA Forum thread, you can see that he replies to everyone, and in my opinion, he's the model of what customer service should be. Honestly, viewing his responses to other people on here, and his swiftness and accessibility, that is what made me decide on going with his product. If more CEO's or companies gave this type of service, I would more than happily buy from them.
In closing, if you have any questions, I'd be more than happy to answer them. I just hope this review can help others out there on not only how to install the protector, but how it works and what to expect.
Click to expand...
Click to collapse
It's how I do most of mine... helps keep the dust to a minimal also
That doesn't answer my question in any way. JLG is a wet install. If you were to read my question, it refers to a DRY install. Of course wet installs can/should be done in that way, but, I was asking about dry ones.
Why wouldn't you be able to do install in a steamy bathroom? Worst comes to worse there is some moisture that gets underneath and will dry in a couple days... Nothing wrong with it... You should do it to keep the dust down... No harm can be done
Sent from my SCH-I605 using xda app-developers app
The adhesive used in dry installs is different than the one used in wet installs, which is why I was asking. Not sure if the trapped moisture would affect the glue used in one of the dry install sp's.
I've put on screen protectors of various phones, including friends' and co-workers. I've never put one on in the bathroom. All the screen protectors I've used were dry ones.
My process is the same in each one:
1. Lay a lint-free cloth (I get mine when I order glasses) on the table.
2. Put phone on cloth.
3. Spray with lens cleaner (the one for glasses)
4. Wipe down with another lint-free cloth. And I spend the most time on this step. I wipe down every nook and cranny and look at it in different angles. I make absolutely sure there are no specks.
5. Lay the SP down and situate it to where you want it to go.
6. Once you're happy with the placement, tape one side with masking tape or scotch tape to the phone. This will prevent the SP from shifting around.
7. Do one more wipe down just to be sure.
8. Start with one corner and slowly peel the protective plastic. At the same time lay the SP down on the phone and using a card (credit card works) squeegee it slowly as you continue peeling.
9. If you see a speck of dust, get some scotch tape and use the tape to get the dust off the SP or the screen.
If you do it slowly and peel it a little at a time and squeegee it as you peel, you'll have very little bubbling and the ones you do, you can easily squeeze out.
Addycki corner
Basically i wanted steam to get the lint or whatever out of the air. Turned the shower off and let the majority of the steam out the vent. Then installed, it turned out fine..
I never understood why it is important to avoid dust when putting on a SP. I reposition mine while installing at least a dozen times on my desk, tons of dust get underneath it, but its really easy to remove. Once you position the SP to where u want, use a piece of scotch tape to tape a corner of the SP and lift it up to about half way, use another piece of tape to remove any dust on the back of the SP as well as on the screen. Repeat process on the opposite corner lift up the other half of the protector. Works wonders.
Here, hope this helps. Just needed to search for "screen protector" in the search bar. In a quick answer, yes it is fine to put a screen protector on in a humid bathroom; it's actually proven easier for me to do it that way.
BillTheCat said:
After reading about the frustrations of those of you who have had trouble installing screen protectors, and your disappointment with the results, I've written this guide to help those of you who suffer from bubbles and dust after installation or who just generally struggle with getting the screen protector applied.
This guide illustrates techniques I've used successfully over many PDAs and phones, and each time I get a PERFECT install, no dust or bubbles and almost always perfectly even edge-to-edge positioning. Yes, you'll need a steady hand and a bit of practice, but it's not as bad as you think, and this technique has worked for me every time.
I can STRONGLY recommend the WriteShield Crystal from Pocket PC Techs, or the Vikuiti films which are made by 3M. Don't let the cheesy packaging of the 3M protectors fool you if you see them in the store - they're quality stuff. What I find different about these two brands is that they seem to have a harder more scuff/scratch resistant surface. I had a WriteShield on my HD2 for over a year without ever noticing any damage to it.
Based on some comments offered later in this thread, I'd like to interject some thoughts by way of personal commentary.
There seems to be some bizarre belief among some XDA members who consider spending the least amount of money they can get away with on a screen protector to be some sort of badge of honor, as though saving $5 on an item that protects a $400++ phone is a laudable goal. Make no mistake about it - just because you may have paid only $50 for the phone doesn't mean that's what it's actually worth. Perspective, folks. Perspective. I've used all sorts of sheets from Boxwave and Fellowes, and none of the 'cheapo' types can hold a candle to the products I advocate for above. I'm not a plastics or chemical engineer, but there is a difference from one sheet to the other. The point about buying a better protector is that you'll have to replace it less often, if at all. In my view, any item that keeps my (very expensive) phone looking newer for longer and thus preserving my pleasure and ease-of-use is worth a few bucks. [Thanks to ephestione for prompting me to discuss this!]
Now, on to the procedure.
** Note: This guide is intended for self-adhesive (non-water based) films, but the techniques should work for those other types like Zagg which rely on a spray method. Some may also wish to use a mild soapy solution and/or diluted isopropyl alcohol to help reduce static and ease positioning, but I caution strongly (and would go so far as to discourage it) as excess can seep into the phone and damage it. It also will make any dust particles hard to see and even harder to remove.[Props to frottage and jmwarren85]**
Preparation:
A clear, clean, well lit work area. (An environment with higher humidity like a bathroom where you've run hot water in the shower can help eliminate static that can attract dust) [Thanks, RammY]
Adjustable height chair to get comfortably close to the phone without straining (I recommend roughly chest height, so that you can easily rest your arms on the work surface).
Sheet of paper or cloth to prevent scratches to phone and to present a clean work area.
Screen protector of your choice.
Lint-free cleaning cloth, either felt or microfiber. I don't recommend toilet tissue (lint residue). Some paper towels are alright, but rough until the fibers soften up, so be sure you allow them to get damp.
Scotch (or other brand of clear) tape. Try not to use tape with very strong adhesive such as clear packing tape, as it will be harder to remove at the end of the procedure.
Cleaning solution such as Windex, or better yet, anything suitable for optics or eyeglasses. What you want is something that won't leave a residue.
Reading glasses, for those of us over 40.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Step 1:
Before you do anything, take a moment to lay the screen protector on top of your phone and move it around a bit to examine how much room you have on the edges. This will give you a sense of how much 'wiggle room' you have and how close on any one edge you'll have to get when doing the actual install. Some protectors are cut with closer tolerances than others. This step will enable you to have a sense of spacing so that you can more closely lay the sheet down with even spacing on all sides.
Also, make a note of the cuts and shapes. For example, the Inspire 4G has a different radius at the top and bottom corners, and the screen protector is cut accordingly. Note what happens in these two shots when I flip the protector in the opposite direction:
Step 2:
Once you've sized up your screen protector layout against the target, prepare two strips of "scotch" (clear adhesive) tape about 1"-2" long each, folding both sides side over to stick it to itself as a 'flap' or 'tabs', which will give you an easy way to grab the tape for removal after the screen protector is deposited onto the phone.
Note: On some larger devices such as tablets, and in certain cases even on smaller phones, using more than 2 tabs can be an aid. Use your judgment. The beauty of this is that you can experiment with the feel of handling the protector prior to application to get some practice, and see how many 'tabs' you'll need.[Props to igalan]
Lay one on the edge from where you will be removing the film backing. What you are doing here is to create scotch tape 'handles' which you use to steer the protector onto the phone, instead of handling the protector itself and risk getting fingerprints on the adhesive.
Step 3:
Clean the phone thoroughly. This is where the lint-free cloth and cleaning solution come into play. Be sure that you've removed all the fingerprints and dust specks. Use the condensation from your breath to see any flaws or residue left on the screen. Often it helps to buff the area when dry. It all depends on whether the residue you're cleaning is greasy, sticky, or whatever. Some smudges respond better to one method than the other.
Step 4:
Lay phone on flat even surface and get your screen protector with its 'handles'.
Holding the one tape 'handle' that you created near the tab, remove the backing from the protector. You're going to get static electricity from this. I've never seen a case where it didn't happen, so be prepared for it, and do your best to keep the protector far enough away from other objects in the area it might come into contact with.
Once you've successfully removed the backing, grab the second 'handle' and SLOWLY approach the phone with the protector, recalling the spacing you saw when you first laid the sheet on top to size it up.
HINT: Rest your forearms or wrists on your work surface to steady your hands, and roll your wrists or move your fingers back and forth for position. Don't try to hover over the screen suspending the protector with your entire upper arms, as this will introduce shake and sway. Bigger distances introduce bigger errors. Smaller distances require smaller corrections. A lesson I learned while taking watch repair classes.
Hold the protector over the display (remembering the spacing you observed earlier) and lay it down starting on one corner or one edge (depending on its shape), and slowly let it fall into place. Do this by starting at the corner or edge, rather than just plopping it down flat. This way, it helps prevent air bubbles from forming in the middle which can occur.
Step 5:
If you've been lucky enough to be in a dust-free environment, and slowly applied the protector from one edge to the other, you should now have a perfectly installed screen film. However, most of us are not that fortunate. This is again where the scotch tape 'handles' come into play.
Create a 3rd length of scotch tape, but this time, only fold it over on one edge, which is where you'll be handling it, and hold it with one hand adhesive side up. This segment of tape will be the 'mop' used to remove any residue.
Find the spot that has the dust specks on it. Because any dust particles will have almost certainly stuck to the backing of the protector, as you pull up on one of the remaining 'handles' that are still attached to the phone, the dust specks will adhere to the protector, rather than the screen.
Note: Some very fine dust particles or fibers can lift the protector from the screen surface just enough so that they'll appear as though they're air bubbles. If you're concerned, follow this procedure and be prepared with a 'mop' to address it.[Thanks, MuF123]
Slide the strip with your other hand to the spot where the dust speck is, and let the film fall down again so that the tape comes into contact with the adhesive, and LIGHTLY apply pressure.
Lift the protector up, peel the 'mop' away and it should take the dust speck with it. Repeat as necessary.
Final step:
Presuming all went well, you have no dust under your screen at this point. Remove the tape flap you made starting from the center of the screen and peeling back to the edges, rather than from the edges inward which would risk lifting the protector off the display.
HINT: Do not lift the tape at a 90-degree angle to the surface of the screen. See if you can pull it off as parallel to the surface as possible, which again will reduce the risk you'll pull the protector off the surface of the display.
If there are any air bubbles, they should be close to the edges, easy enough to push out using your finger or a credit card covered with your cleaning cloth to prevent any grit from the card from scratching the protector.
Hope this helps!
Click to expand...
Click to collapse

Detailing Spray as Oleophobic Coating

If you find the dust attracted to your screen protector or find your finger drags on the screen, a car detailing product, (such as Meguiar's Ultimate Quik Detailer), briefly sprayed onto a soft cloth and then rubbed on to the screen, works wonders as a temporary oloephobic and anti-static coating.
Any decent detailing spray will do the job, no affinity with Meguiar's.
Good tip.
Maybe I'll do the test when the fingerprints will bore me

Yet another DIY Oleophobic coating (with car wax)

So as many of you have tried car wax I decided to give paint sealant a go.
As the one plus has a factory screen protector with questionable Oleophobic coating (if any) I was kind of surprised that it was very grippy and not at all slick.
So I decided I was going to use an automotive trick.
First I tried with rainX Ultra Wax (I had it lying around). The outcome was good a bit slipperier than before but fingerprint resistance wasn't all that great and smudges did appear.
So I decided I was not going to go the carnauba wax route and look into synthetic paint sealants mostly because by design they are non-abrasive and are designed to protect whatever is under them by repelling water and just overall forming a barrier.
So I went off and got a bottle of Autoglym Extra Polish Protection. (Or any automotive paint sealant product should work)
The results are much better than wax. After a 30 min cure I wiped off the excess and it seemed the same as wax so I semi gave up and went to bed. The next morning I noticed the screen protector surface felt a lot slicker. Turns out sealants are slow cure products and they will take a few hours to reach full hardness once they do they work adequately well. Mind you they only help finger prints show up less and make them easier to clean off but then again a true oleophobic coating in my experience does about the same just with better efficiency.
So if you're factory screen protector is a smudge magnet here's something to try if you're using car wax I think the cure time is under 30 min to reach full slickness and if you're using a synthetic sealant you should consult the manufacturer. Avoid cleaner wax as they contain polishing compounds which may harm the plastic screen protector.
Another option: https://www.amazon.com/dp/B00LKYW6M0/ref=cm_sw_r_cp_apa_RyNYzbNN58FBZ
Can find all kinds of diy oileophobic coatings online. Would love to hear your these compare to the coating recommended by the OP in terms of durability. Good thread!
NanoGo liquid screen protector for mobile devices
Phones & Tablets Monitors & Camera Lenses - Explore & Order!
Sorry, site only FINNISH language, use google translation.
https://bluebiit.com/
Let us know whether it holds up well!
I didn't go and buy the Fusso stuff because the label says it must be applied to glass. I'm trying to add a coating to the stock factory plastic screen protector.
As for durability only time will tell 48 hours later and finger prints are still very easy to remove but the real test would be how it's like after a month.
That said the purpose of Automotive paint sealant is not that much different from a oleophobic coating automotive paint sealant is designed to offer a sacrificial layer of protection against tar / UV / rain / bird droppings / dust so that the paint itself is never touched. Likewise most of these coatings are designed so that said contaminants are easier to remove once they do touch your car's panels. Ergo finger prints seem like they are an equivalent contaminant and would work the same way so far it's holding up and the screen protector is a lot slicker than without the coating. I tested it by using isoprophyl alcohol to remove the car wax an the factory plastic screen protector was much grippier.
You can wipe off the haze after 20min or so but most car waxes take a few hours to fully cure as the solvents dry out. Just be careful around edges some car waxes will leave a line of wax visible after it dries along the edges of a screen protector the sealant I'm currently using doesn't seem to do this so it's super easy to use.
So after a few months of use durability seems questionable the coating seems to wear off after about 2 weeks of use so overall it's not that effective.
Just updating this in case people were wondering how successful this was.

Categories

Resources