Related
so yeah..... (dont all you laught now) but i just droped my phone in the toilet *b4 pissing thank god*... and it shut off... i took out the battery ASAP... and use a hair dryer to dry it out.. now its under a fan blowing semi cool air....
did i just completly **** my phone.... im sure i did... anyone know of something 2 do..
please help... ive been without my phone for 20 minutes.. and molski is releasing his 3rd ed rom soon.. and i wont even be about to use it
I once had Kool Aid poured down a motherboard of an open computer case. A lot of cleaning and a day later, it still worked fine.
Is there hope? Sure. Are the odds in your favor? Probably not.
But since you already got your phone wet, you know your warranty is gone. My advice (it's worked for me before) is to take the phone apart carefully, dry it off completey, clean it with 90% isopropyl rubbing alcohol and a microfiber cloth, and then wait for it to dry again. Hopefully that will stop the corrosion and hopefully removing your battery immediately worked to your favor before anything shorted out.
Good luck!
help again
ok welll first of all.. ummm im not gunna say WHY, but my warrenty wont work period on the phone. next what do i use to take it apart??? i know not to even try to turn it on for atleast a day or two..... and drying under a fan right now... and what if i cant clean with with 90% whatever you said and a microfiber thing... cuz i wont be able to get that untill tomrrow
I highly suggest you open it and do as was suggested earlier. Same thing happened to me on my Nokia phone and the above procedure saved it. Goodluck!
well i just left it under a fan all night.. and tried it this morning and everything works fine.....WAHOOOOOOOOOOOOOOOOOOOOOOOOOOOO
You may want to seal your phone in a plastic bag with some instant rice or cilica for a couple of days. This will pull out any remaining moisture. If you did not take your phone apart I'll bet there's still water inside. If you don't get it out corrosion will set in.
Good luck
Phone wet - solutions
Well, I'm glad you saved your phone.
With all electrical equipment it's adviced to:
- switch it off ASAP
- the shorter it was on while wet, the less chance you have damaged it
- ensure that it gets completely dry
- a hairdryer can help, but at least open the phone as far as possible
- you can also leave it open on a warm place in the house,let the sun shine on it
- I would even let it dry for a few days
I must say, it also depends on the type of fluid. Salty water, coca cola, ice tea, coffee....these have a bigger chance to cause damage. If that happens, while switched off, clean a while well with just water to get to salt or sugar out. Then let it dry.
happend to my phone as well, after taking a piss (and flushing the toilet). I only opend the keyboad and lett it dry for a day on the heating. works fine [email protected] first the display was flickering quit a lot. but now, a week later... it's working as before.
heya guys,
today I was talking on the phone and the phone droped from my hand into toilet. I bring it out fast and removed the battery. I dont know what should I do now,. any advice!!!! will Vodafone accept it for waranty!!!
Usually for any electronic device, take as many bits out as you can an stick it somewhere warm for a day or 2, should get some if not all functionality back, I've dropped many things in the bath and had them back working again. Don't, however, try and power it on until it's had chance to dry out. The touch screen may be an issue though...not dropped any touch device in some water yet to test if the same rules apply....
Stick it in a bowl of (uncooked) rice, it'll help pull out the water faster.
whatever u do dont use any thing like a fan or blow dryer, cause that will just cause the water to go deeper into the phone, use a vaccum to suck the water out as much as possable,then like he said place the phone in a bowl of un-cooked rice for a day or two, good luck.
A little combo of what has been said: put it in a bowl of uncooked rice right at the counter where it gets a lot of sun (battery should be out obviously). The BIGGEST mistake you can do is test it out after a day when you "think" all the water is out. If it isn't and you turn it on, it could cause further damage. I know you're urgent to find out if it works or not, but give it three days with three days in the above conditions. You'll also probably need a new battery.
mp.goldfinger
will Vodafone accept it for waranty!!! - - -- no
Vodafone will not accept phone Warranty
The diamond has a sensor for water
Thanx guys......but I did turn it on today Bcause I really need a number everything is alright but the screens is still fuzzy. I wont use it for at least a week and see what will happend.
i hope you flushed the toilet before you dropped it.. =) otherwise there will be some.. sh*t inside the phone and its not easy to clean
yeah, definitely make sure its in rice, and sunlight doesn't hurt..
And the moral of this story
Don't take your phone out of your pocket when in the toilet.
It's also unhygienic.
Take care of your phone and your phone will take care of you.
I went to a festival where I was so drunk that my diamond went out of my pocket when I got ready to sleep in my tent. And next morning I fond the phone in a little water pool inside the tent. But all the functions still work after I let the phone dry for 1 day.
Uncooked rice (as been mentioned before) is the best solution.
Take your time, as been said before, it will take a long time before all the moisture is out.
Nowadays the chips are very small, water easily lodges between the BGA balls, and it takes a while to evaporate.
just leave it for a week in the bowl of uncooked rice (preferably on a warm sunny place.)
Remove stylus, back cover & battery before sticking it into the bowl.
It's not under warranty: it has a moisture sensitive sticker which turns red when it was in contact with water.
Because it isn't under warranty, I personally would take the device apart, and dry the parts seperately, but that isn't very easy if you haven't done this sort of disassembling before.
Revert to this only if you have absolute confidence (and the service manual ).
Best of luck!
Please keep us posted.
EquinoXe
The problem is long term, the moisture will cause corrosion on the fine
PCB tracks etc. even after its dry, Best thing to do is pull the device appart as best u can get a tooth brush and a can of CRC CO CONTACT CLEANER
blue and white can @ any good electrical wholesaler. spray all the circtry and componets not the screen. and scrub with a tooth brush dont knock
off any small componets and then let dry for a day or 2 best bet is to use compressed air to blow off excess liquid spray from under the chips..
I am in electronic repair hope this helps
This happend to my LG 2 years ago ...into the LOO and i done the process above and its still working today the quicker u dry the water off initialy the better..
thanx guys.....unfortunately I have to buy a new LCD for my diamond as all water has gone inside the LCD and damaged the sheets inside the LCD. I have removed all parts and I am waiting for LCD delivery that cost me 40£
Aww, that is unfortunate..
Hope the LCD transplant will bring it back to life.
I had almost the same issue, but in my case, what I did was that I droped some alcohol inside the power button when I was trying to clean the screen with a tissue and some alcohol. Now the power button works in a faulty way and it tries to reboot every time I click on it. It's like the single click is always a double click on the power button. Any suggestion on how to fix it? This happened to me like 2 months ago and it is still like this.
djfuego said:
Don't take your phone out of your pocket when in the toilet.
It's also unhygienic.
Take care of your phone and your phone will take care of you.
Click to expand...
Click to collapse
I dropped an iphone inside the toilet. It rang I went to pickup and it slipped out of my hands.
Apple replaced it though. They didnt even test if it was water damage. LoL
....and I might also suggest that you don't eat the rice later!
Aww thats pretty sick
Have done the same thing, about 2-3 years ago (luckly not with my HTC TD)
All the advice above is right about drying it out, but the main issue you'll have is impurities in the water which, once the water has evaporated will leave residue. The worst is actually salts. These will dislodge components in the phone, and usually it'll never be the same again. Often the water gets under BGA components that arent encapsulated, or between pins of components, and once the water evaoprates the salt cyrstals left behind expand into those gaps.
You can wash the pcb in distilled water, or certain alcohol solutions - depending on what residue there actually is. If you use normal water you'll just make it worse, because that has impurities in it too.
You could have done the same with the touchscreen, but you would need to dismantle it.
Sometimes you get lucky and it all works ok for months.. lets hope you're lucky
So I did a pretty stupid thing yesterday and decided to pull out my G1 while it was raining cats and dogs. At first it did not want to start up at all but I let it just sit for a few hours. Now it starts up but I cannot get into recovery.(hold home+power) It just stay on the T-Mobile G1 screen and does nothing. I also tired flashing the recovery image again and nothing. One more important thing when I connect my USB cable it does not give my the option to mount my SD Card. It only charges the G1.
Thank you in advance for helping.
I'm not sure why exposing it to rain would merit flashing the recovery image.
It might be too late, but you might try putting it in a bag of rice over night to pull all the moisture out.
xelaboy said:
I'm not sure why exposing it to rain would merit flashing the recovery image.
It might be too late, but you might try putting it in a bag of rice over night to pull all the moisture out.
Click to expand...
Click to collapse
+1 on the rice. take the battery out first.
Thanks for the idea. I let it sit over night and gave it a full charge. Everything works fine but I still can't boot into recovery. I tired flashing the latest recovery through terminal emulate and also through the Cayongan reboot but still no luck. I'm suck on CM 5.0.7 Test 3 and my battery is dying way to quickly.
This sucks @ss! I went to T-mobile to look for a replacement phone but T-mobile has some crappy @ss Adnroid phones. I didn't want to go through google to get a Nexus One.
THANKS AGAIN GUYS!
Whenever you get a phone or other piece of technology wet, the last thing you want to do it try to turn it on while its still wet. You might end up frying something. Next time, stick it in rice for 24 hours before even thinking about trying to put it on, or put it in your oven at about 120 degrees for a few hours to let it dry out.
http://www.popularmechanics.com/technology/how-to/tips/4269047
Even if a wet cellphone seems dead, there's a good chance it can be resuscitated. Just make sure you act fast--the longer the water sits inside, the greater the likelihood it will destroy the phone for good.
This is a DIY moment. While consumers are conditioned to send back broken merchandise, your phone's warranty probably doesn't cover water damage. And you may not have much luck pulling a fast one on your phone company--most of today's phones come with a "water sticker" that permanently changes color if it gets wet.
The first step: Immediately cut the power by removing the battery. I know it's tempting, but resist the urge to power up your phone to see if it works--just turning it on can short out the circuits. If you have a GSM phone (the type used by AT&T and T-Mobile), you'll want to remove the SIM card as well. Even if your phone turns out to be beyond repair, the SIM should retain a lot of its onboard information, such as the contacts in your phone book.
With the battery safely set aside, you now have one goal--dry your phone, and dry it fast. If you let the moisture evaporate naturally, the chance of corrosion damaging the phone's innards increases. Instead, blow or suck the water out. But don't use a hair dryer--its heat can fry your phone's insides. Instead, opt for a can of compressed air, an air compressor set to a low psi or a vacuum cleaner (a wet/dry Shop-Vac would be perfect). The idea is to use air to push or pull moisture out through the same channels it entered.
Finally, use a desiccant to wick away any leftover moisture. The most convenient choice is uncooked rice. Just leave the phone (and its disconnected battery) submerged in a bowl of grains overnight. If you're worried about rice dust getting inside your phone, you can instead use the packets of silica gel that often come stuffed in the pockets of new clothes. But acting fast is far more important than avoiding a little dust, so don't waste time shopping if you don't already have a drawer full of silica gel.
The most important thing to remember is to avoid heat. That means no hair dryers, ovens, microwaves or extended periods in direct sunlight. While heat will certainly evaporate the moisture, it could also warp components and melt adhesives. Those fragile glues are also why you'll want to avoid dunking the phone in rubbing alcohol (an oftÂ*prescribed tip on the Web). Alcohol is a solvent and can dissolve the internal adhesives. (If you drop your phone in the toilet, it's okay to wipe the outside with alcohol to disinfect it.)
One final, perhaps surprising, note: If your phone gets soaked in salt water, you should probably flush the whole thing in fresh water before it dries. When salt water evaporates, it leaves crystals that can damage a phone's fragile components. Just be sure to remove the battery before flooding the device.
PS: I prefer ziplock bags versus a bowl. Also, instead of rice you can use your fridge. The fridge works by sucking moisture out of the air. Or better yet combine both. Place it in a bowl of rice and then in the fridge.
i reccomend restarting back at rc29 if ur in the usa or rc7 if ur in the uk. if u need a for sure how to guide click here
that guide has proven to many users to work flawlessly and save time compared to the old method using telnetd lol
Thanks to everyone. I got it working. I just use ADB to erase and update my recovery image. Then used ADB to boot into recovery and it worked after that.
I recently dropped my phone in water. It was only submerged for a few seconds, and the litmus paper inside the battery compartment wasn't even tripped. The sliding door on the USB port was open, however, so I suspect water got in either through that or the headphone jack. The screen is readable..barely. Every other horizontal pixel on the screen is a black line. Can anyone tell me if it's possible to recondition the screen, or if there is any way at&t would be able to tell that it's damaged from water as opposed to a fall? Thanks in advance.
Sent from my SAMSUNG-SGH-I897 using XDA App
Give it a few days to let it dry out. Even take the cover, battery, sim, etc. out. Hit it with a blow dryer. Not super hot, but enough to help drive water out of the internal circuits. My fuze fully recovered after like 4 days. Worth a shot.
Sent from my SAMSUNG-SGH-I897 using XDA App
If you haven't already read this thread, I'd suggest you do. Same sort of thing happened here.
http://forum.xda-developers.com/showthread.php?t=807606
Quick story, and then a possible solution.
2 years ago I was sitting on the toilet with my iTouch playing Crash Kart Racing. I stood up to finish my business, put my iTouch in my hoodie pocket and leaned over the toilet to flush. *PLOP* Yupp, iTouch in the toilet. Luckily it was in clean water but it was still damaged.
The screen was effed and everything. So I figured I'd just let it dry out. Here's the solution part. Stick your phone into a back of rice. Not cooked rice, raw, hard, rice. Rice absorbs moisture, it acts like a natural silica gel, you know, those packets you get in your shoe boxes. Let it sit for a few days and hopefully all will be well again.
Epilogue..... I still bought a new iTouch cause my battery wound up not lasting very long after that...
THIS THREAD IS FOR PEOPLE WHO HAVE A WATER DAMAGED NEXUS 5, OR HAVE JUST DROPPED THEIR NEXUS 5 INTO WATER. READ NOTE BEFORE REPAIRING
NOTE: The water indicator (shown as the red square in the photos) is located just above the sim card tray. It is only a few millimeters away from the edge of the phone which makes it VERY SENSITIVE to water. It turns from white to pink/red if it has been exposed to water.
My phone dropped into the toilet and was submerged for only 0.5 -1 second. This was enough for the indicator to go off. If you do not want to open up the phone, check the sim card as mine had small pink/red residue on it after I took out the sim card.
The location of the indicator makes it very easy for the indicator to go off. I can easily see how rain, extreme humidity, or even a small pool of tap water could make it go off if the sim tray is not inserted properly, let alone if it was submerged.
Helpful Resources/Guides: Nexus 5 dropped in toilet, recovered: http://www.reddit.com/r/Nexus5/comments/1wf4gu/guess_who_dropped_their_nexus_5_in_the_toilet_a/
Nexus 5 water repair SUCCESS STORY: http://forum.xda-developers.com/showthread.php?t=2618121
How to open Nexus 5: http://www.ifixit.com/Teardown/Nexus+5+Teardown/19016
Opening Nexus 5 (more detailed) http://forum.xda-developers.com/showthread.php?t=2542873
Repair guide (some steps are controversial, caution) : http://www.reddit.com/r/LifeProTips/comments/1npt9v/this_actually_works_if_you_drop_your_phone_in/
REPAIRS:
Read links/stories above for steps to recover Nexus 5, my method has not proved successful thus far. Please read the thread for other methods too.
The general consensus is to:
1. MOST IMPORTANT: Turn the off phone immediately. If your phone is off, don't attempt to turn it on or you will risk damaging the internals.
2. Use a cloth/paper towel to immediately soak up water around phone.
If you do not want to open up the phone for warranty purposes:
3. Place phone in an airtight container with activated silica gels, or with rice for few days.
Note: This is not the best method if the phone was submerged for a relatively long period or if you spilt coffee/soft drink on your phone. There is a high risk of corrosion with this as the water may be trapped inside for a long period of time causing internal parts to corrode. Other methods have proven more successful. Alternatively people have had success (in this thread, please read) by drying out their phones via traditional methods like using blowdryers etc. when the device was exposed to water for a SHORT period of time. Make sure you err on the side of caution when using heating methods as to not damage the internals, never use anything that would make the device too hot.
OR
If you don't mind opening up phone (fairly certain indicator has gone off and want to void warranty). If I could go back in time I would probably use this method:
3. Open up the phone by prying off the back (method in the link above), remove the battery and carefully assess the areas and components that have collected water. Remove the water and dry it out as much as possible. This may be enough if the phone was not fully submerged.
For more serious cases: For coke/coffee/saltwater or if the phone has just been sitting there a long time after water exposure:
- A lot of people have had success by washing the phone with deionised water first and then submerging it in pure ethanol (without battery). This serves to clean the phone of the contaminants and to prevent corrosion. (especially if you dunked in it coffee/soft drink). Theoretically the water/ethanol would not conduct electricity due to the lack of impurities in them.
-If you have left the phone untouched for a while without cleaning it, there may be some build up of corrosion. People suggest scrubbing the white corroded area off using small/light brush strokes of a soft bristled toothbrush either after the wash phase (deionised water) or just after the submerging phase (ethanol)
Many different methods suggested in links above. Make sure you read through the thread, there are various success stories here too.
My case:
As soon as I dropped it into the toilet, I turned it off straight away. I dried it off with a paper towel and stuck it in rice for a few days. Then I moved to a sealed container of silica crystals for about 5 days. Then I let it dry on table for another 2. Then it did not turn on, unresponsive. Did not charge or get recognised via USB. This was probably not an optimal repair method. The methods above may be more useful. But if you know the indicator has gone off, it would be best to open up the case straight away to drain the water out.
Then I opened up my Nexus 5 (after a week of deciding what to do). I could see small amount of corrosion around the sim tray area, usb insert area and others around the phone. Then I dipped the motherboard and into a bowl of isopropyl, enough to submerge it for 5-10 minutes. Then used gentle movements of a toothbrush to focus on corroded areas. I am now just letting it dry.
I will update this thread if the repairs are successful.
Update: Phone is still unresponsive, it may be that the battery is dead or one of the parts do not work at all. Any suggestions?
UPDATE 2: Ended up just buying a new Nexus 5 back in March, old one is just sitting here in the cupboard still unresponsive. I may try to buy a battery to see if it's a battery problem but for now I'll just leave it. Not sure if it would sell much for parts.
Please feel free to post other helpful resources or your own experiences on saving a water damaged nexus 5.
NOTE: I am from Australia. The cost to repair a water damaged Nexus 5 was a fixed cost of $290 AUD (16 or 32gb) if you send the phone to manufacturer (LG). Water damage is not covered under warranty but LG still accepts repairs out of warranty at a fixed price. The lady on the phone said that they would replace the motherboard. Opening up your device will void your warranty so please be aware of this before you try to repair it.
NOTE 2: If you live in the US, google has confirmed it does one time replacements no matter what. Read below: http://gizmodo.com/google-will-apparently-replace-your-nexus-5-no-matter-h-1630258357
You did it wrong. You must pull battery asap, and clean evening with alcohol
I feel this needs to be asked, had you conducted business before your phone went for a swim in the porcelain pool? ;D
GR0S said:
You did it wrong. You must pull battery asap, and clean evening with alcohol
Click to expand...
Click to collapse
At the time I was still considering whether to send it back for repairs. Pulling the battery out requires taking the phone apart and voiding warranty. But looking back I probably should have opened it up straight away.
Phone is still unresponsive, is there any way to check which individual module or part of the phone doesn't work? I have a feeling some are working while others are not. Do electronic repairs shops have tools to test this?
Parts are easy to obtain: http://www.etradesupply.com/lg/android-models/lg-nexus-5.html but it is just a matter of knowing which part to get, that is assuming the main motherboard/CPU is still functioning.
eastpac said:
Phone is still unresponsive, is there any way to check which individual module or part of the phone doesn't work? I have a feeling some are working while others are not. Do electronic repairs shops have tools to test this?
Parts are easy to obtain: http://www.etradesupply.com/lg/android-models/lg-nexus-5.html but it is just a matter of knowing which part to get, that is assuming the main motherboard/CPU is still functioning.
Click to expand...
Click to collapse
When you say phone is unresponsive do you mean that it won't come on at all?
sent from my neXus 5
OuncE718 said:
When you say phone is unresponsive do you mean that it won't come on at all?
sent from my neXus 5
Click to expand...
Click to collapse
Yeah it didn't turn on after I took it out from the silica gels. Also after I cleaned/submerged the phone parts in isopropyl and reassembled it doesn't turn on at all. I tried plugging into computer too but it didn't work either.
eastpac said:
Yeah it didn't turn on after I took it out from the silica gels. Also after I cleaned/submerged the phone parts in isopropyl and reassembled it doesn't turn on at all. I tried plugging into computer too but it didn't work either.
Click to expand...
Click to collapse
The computer did not recognize the phone? Most times when a phone is off the computer would at least make a sound once plugged in. How was your battery life before the incident? Was the phone almost dead?
I would probably take the phone back apart, clean it one more time with the alcohol and a soft brush toothbrush, dry it with a blow dryer (on its coolest setting so you don't damage anything) and then put it back together.
Use this site as a guide and do a side by side comparison. Maybe you forgot to plug a cable back in. http://www.ifixit.com/Teardown/Nexus+5+Teardown/19016
Good luck!
sent from my neXus 5
OuncE718 said:
The computer did not recognize the phone? Most times when a phone is off the computer would at least make a sound once plugged in. How was your battery life before the incident? Was the phone almost dead?
I would probably take the phone back apart, clean it one more time with the alcohol and a soft brush toothbrush, dry it with a blow dryer (on its coolest setting so you don't damage anything) and then put it back together.
Use this site as a guide and do a side by side comparison. Maybe you forgot to plug a cable back in. http://www.ifixit.com/Teardown/Nexus+5+Teardown/19016
Good luck!
sent from my neXus 5
Click to expand...
Click to collapse
No I tried it on a few computers, didn't manage to make it get a sound or anything. Battery life was normal before I dropped it. I can't remember what percentage it was on exactly when I dropped it, if I had to guess i think it was on 10-30%?
Yeah I'll give it another go with the cleaning. Should I submerge the screen in isopropyl too? I've only done the motherboard, bottom grill and cables so far. I left the battery out.
Also with the brushing I'm scared I'll break something: http://www.youtube.com/watch?v=9QHn3ItE7ME But am i meant to use as much force as this guy in the video? I was way more gentle than that
If its a soft tooth brush and only a soft tooth brush then I'd say go in for the kill. Lol. That's about how much force I used on my Galaxy Nexus when it had water damage and I recovered it with no issues at all! Use your discretion though. Use as much force as your comfortable with and make sure to thoroughly dry it. I'd also clean the battery connector but with a DRY brush. Maybe that's where the issue lay.
sent from my neXus 5
Were there number 2 floaters when you dropped it? Did you soak it in rose water?
Sent from Nexus 5 (?) on Slimkat
yeh found a couple of mars bars on the screen when I took it out and mountain dew dripping from the sides.
haha nah it was clean at the time, just fell in from the towel rack
Phone probably short circuited when powered on
Sent from my Nexus 5
Little bit of trolling, sorry,
Feel really sorry for the guy who lost his nexus 5 coz of water damage, but I couldn't help but giggle at times at the process he was making himself go through trying to save the nexus, all because of a 0.5 to 1 second of water. Here is the process that I went through with my phone.
Dropped my Xperia Z Ultra a few days ago in a bubble bath tub, then spent about 5 - 8 seconds just looking for it, because of the bubbles.
Then I found it, Wiped it off immediately on my chest, it was soaked, then I turned it on. then I got into the bath tub with it, then watched some YouTube, visited xda forums, after that decided to watch some porn, then my wife started banging at the door "what the hell are you watching!?" then I got out, Wiped phone with towel. Then ate some chicken with rice, with my phone next to it not inside it.
Anyway think the nexus 5 is a gorgeous phone, that I would of have definitely wanted it if I hadn't experienced relaxing bath tub times, that all started with the original xperia z.
I still envy people that I had seen using it, I think it's the most beautifully designed phone ever created. With Sony and Htc as close second.
Sent from my C6833 using xda app-developers app
dicecuber said:
Phone probably short circuited when powered on
Sent from my Nexus 5
Click to expand...
Click to collapse
Are the chances of a short circuit fairly high in circumstances like this? Any way to confirm if all components are dead? I'm assuming that would probably kill off the motherboard/cpu so cleaning it won't do much in that case. But might i'll give it another clean just in case
bucho2004 said:
Wiped it off immediately on my chest, it was soaked, then I turned it on. then I got into the bath tub with it, then watched some YouTube, visited xda forums, after that decided to watch some porn, then my wife started banging at the door "what the hell are you watching!?" then I got out, Wiped phone with towel. Then ate some chicken with rice, with my phone next to it not inside it.
Click to expand...
Click to collapse
LOL cheers man, i'll be sure to quote that at my nexus's funeral to remind it of the life it could've lived
How about getting wet with Salt Water !
Hi all, great thread, glad I found it. Want to hear another "got wet" story?
My Nexus 5 (and an iphone5) was in an Outdoor Products "dry sack" on an ocean boat ride in Brazil. This one at outdoorproducts.com, their 3-pack-ultimate-dry-sack
Caution! It was properly sealed, but still let saltwater in through the seams from splashes. The phones basically sloshed around in a cup of water before I knew it. Defective or wrong material to trust. In any case, the phone didn't work after, dead. To repeat, neither phone was ever submerged or dunked.
So I didn't have any isopropyl alcohol, but here they have something similar, ethyl alcohol (for cleaning, usually 46% solution). I knew that the rest was "hydrated" so I searched for a more pure form; found a 98% bottle. It is very hard to find (banned from sale because flammable) but I found a source. So I submerged the phones in this ethyl alcohol for 5 min. then let them sit in rice inside one of this company's "dry boxes" (which I should've used instead, kick to rear).
After 2 days, my Nexus 5 turns on! And, charges... and connects to wifi and receives messages. but the phone screen is like a tie-dye t-shirt. "Touches" won't unlock the screen, so I can't access apps to retrieve data. And, the phone won't connect over USB to the Android file manager.
I'm hoping a technician/hacker back in MA can open the phone, take out the 16gb internal storage (Sandisk SDIN8DE4 16 GB NAND flash) and get my valuable photos/videos off !
---------- Post added at 05:02 PM ---------- Previous post was at 04:36 PM ----------
I was just googling... from ifixit's forum a moderator said that it was possible to read data from a NAND chip. He mentioned some sites, and from their I found a data firm, eprovided.com -- fyi this is no endorsement. I'll have to call them Monday to see if they can do chips from wet phones!
@placker have you tried hooking it to a different computer? Have you had the android file manager connected with this device before this incident, or did you install it just now? Have you tried booting to fastboot?
Just curious if it recognizes via fastboot
Sent from Omni Nexus 5
@AndroidSlave
thanks for the reply -- the phone had previously worked fine with the Android File Manager (used on Mac). That was my big hope... but alas no.
I don't know how to do fastboot... I've started/hard-shutdown the thing many times. Believe it or not, the phone's alarm clock just went of at 8pm. No way to shut if off since I can't bypass [what I think is] the lock screen. I can see the wacked video screen changing in response button presses of volume or the 10-second power button press.
I'll google the technique...
placker said:
@AndroidSlave
thanks for the reply -- the phone had previously worked fine with the Android File Manager (used on Mac). That was my big hope... but alas no.
I don't know how to do fastboot... I've started/hard-shutdown the thing many times. Believe it or not, the phone's alarm clock just went of at 8pm. No way to shut if off since I can't bypass [what I think is] the lock screen. I can see the wacked video screen changing in response button presses of volume or the 10-second power button press.
I'll google the technique...
Click to expand...
Click to collapse
Do you have a PC in your home? I am curious to see if anything gets recognized on a PC. My Mac (I am a Mac user) is finicky while my windows device works fine.
If u can get it recognized in fastboot you may be able to pull your data without issue...
If I were you I would first see if I could get it to be recognized on a windows PC
Sent from Omni Nexus 5