The update came thru on my Hd7 3 days ago. All's well it seems, but the camera won't start. Tried rebooting a few times, still the same. Anybody else had this? + I can't see what this update has done..
i have the same problem man it just stop but before the update so i think its software problem
i have the same problem how i fix this?
Wait... Update? Like an official tmobile update?
Its got nothing to do with the rom or any update and software , i had the same problem n i did a lot of tests on the software but no luck !
then i opened the top back cover of the hd7 , removed battery , open top 6 screws , (no need to open the bottom cover and 2 screws with void label ) , gently remove the plastic cover , you will see the camera module there push it down to the board and youll hear a click , ITS OK NOW
Same issue after the upgrade
i also had the same issue with the camera after installing the update.
up to that moment, all was working fine.
in an attempt to fix this, i performed a few rests through the Settings->About->Phone reset. after each reset, it seemed to be working for a few moments, but then, after a while, it stopped again.
called HTC and they could not help me other than saying to reset the phone.
i did find that a hardware reset using the buttons is performing a different level of a rest and for now, it seems to solve the problem. (power off, Power on with vol up and down pressed).
as others on the thread experienced, i do blame the software update.
Related
Today I got my Kaiser back from repairs. I got my mainboard replaced because of connection issues. It came back with it's original 'software'.
After installing Hard-Spl (white screen edit) I successfully flashed "Dutty's Official WM6.1 5.2.19209 Release" to my Kaiser.
I wanted to Hard Reset my device using the soft-buttons and soft-reset method, but it seems to be broken (?). I managed it in the past (before flashing and repairs) but for some reason it doesn't work anymore. Soft-resets and Bootloader mode still work.
Anyone got an idea?
Thanks in advance
P.S.: In the meantime I hard-resetted my device by going to Settings => System => Clear Storage
Dr. Strangelove said:
Today I got my Kaiser back from repairs. I got my mainboard replaced because of connection issues. It came back with it's original 'software'.
After installing Hard-Spl (white screen edit) I successfully flashed "Dutty's Official WM6.1 5.2.19209 Release" to my Kaiser.
I wanted to Hard Reset my device using the soft-buttons and soft-reset method, but it seems to be broken (?). I managed it in the past (before flashing and repairs) but for some reason it doesn't work anymore. Soft-resets and Bootloader mode still work.
Anyone got an idea?
Thanks in advance
P.S.: In the meantime I hard-resetted my device by going to Settings => System => Clear Storage
Click to expand...
Click to collapse
Few Tricks, Make sure you are not plugged in USB. Make sure you are not "fat fingering it." Some people use chopsticks to be sure. And Hold it for long after the Screen goes Black.
Believe me, I've already tried the things you said.
Although I successfully mananged in the past to hard reset my phone, I checked the threads and the following vid:
How To Hard Reset Kaiser:
http://www.youtube.com/watch?v=fZPzT_L2FZQ
Usually I am the problem, but this time I can't figure out what I'm doing wrong.
Just wondering:
Which part of the Phone (ROM) is in control of the Hard Reset part? (e.g.: Bootloader, Radio Rom, Regular Rom,...)
Use "Clear Storage". It does the same thing.
Also, JM is most likely correct. It is most likely an issue of how you are pushing the buttons. Make sure you hold only ythe soft keys first, using your fingernails, then push the reset tab on the bottom & hold it. Don't just push the reset & release, but keep it held down.
Based on your previous message about your phone being haunted - mine is too btw, I think it's because the soft buttons aren't being acknowledged by the OS - which implies some REAL big problems.
I took mine back to the T-Mobile store today where I got told that it needs to be sent back to their workshops to fix it... and then got told that "mostly they just send out a new phone".
My phone is exhibiting the following symptoms.
1) Green and Red phone buttons do not work.
2) Soft buttons do not work.
3) D-Pad and wheel work intermittently.
4) (and most strange) the back-space key on the slide out keyboard does nothing, and on the virtual keyboard it flashes (to suggest that the key is being pressed) but still does nothing.
I've tried to access the bootloader, and perform a hard reset. I'm now looking for the original T-Mobile ROM to install (which was why I went into the shop), as the issue around the backspace key implies to me that the issue is in the OS not in the hardware.
Jon
Thanks already for all the input.
I've been trying all weekend in every different possible way to perform a hard reset. Fat fingering is really no possibility anymore. I've used every possible tool I had (needle-nose pliers, chopsticks, pens,...) to eliminate fat fingering.
But nothing helped. Jon (a nice guy) might have given a possibly correct diagnosis for my problem. But it wouldn't explain why I still can get into the bootloader.
Problems since receiving my phone from repairs:
Backlight changed out of itself => performed Hard Reset
Phone pad pops up and seems to start dialing => flashed new ROM
Wakes up constantly after a few seconds from standby => performed Hard Throw against the wall
As you can see, my latest problem is that the phone automatically wakes up from standby after a few seconds. The weird thing: it only does this when I put it in standby, but it doesn't wake up if it enters standby by itself.
=> NOTE: This may support the 'fat finger'-theory: the Kaiser gets some sort of keyboard input due to faulty hardware. Therefore I cannot Hard Reset my device, because of the additional faulty input.
I've used the "Clear Storage" method to perform one of my hard resets, but this has to be solved. I will be sending the phone back for yet another repair.
Thanks again for your input everyone.
Problem found?
I think I found the problem:
I just noticed that the camera button is already pushed in halfway (like when you focus the camera before you take a picture). If I push the button gently, it immediately takes a picture without focussing (it does automatically focus before taking the shot, but not on my command).
Also, when I enter the camera app, it sometimes instantly focuses. Other times I cannot focus at all.
Hard reset is still no go.
Yet another thanks for your useful help.
Maybe found the solution?
Hi Guys...
I found that by tapping the base of the phone, it "unlocks" itself, thereby making it work. It's become *S*L*O*W* as hell, and I'm really tempted to ask them to take a look at it, but right now I need all the functions, so I'm holding off.
But, give that a try and see what happens!
Jon
Thanks for still answering my question. Go community!
Dr. Strangelove said:
...
I will be sending the phone back for yet another repair.
...
Click to expand...
Click to collapse
Last week I finally received a fully functional and working Kaiser (have been waiting for that since december...). I couldn't accept a disfunctional Kaiser coming back from repairs.
The problem did indeed seem to be the camare button that was stuck. I tried really hard to get it to unblock, but I didn't work. I must say, I didn't try your method (didn't think of it).
Still thanks a lot.
I am experiencing exact same issues on my Kaiser (Tilt), it randomly starts to type stuff in the phone application on its own and I can't do anything to stop it, I have replaced ROMs, SPLs, Radios, now using a shipped rom with shipped radio but still that problem comes up after a few days of usage and doesn't go away until I hard reset, anyone knows what I can do to fix it? it's probably out of warranty. I checked the camera button and it seems fine.
I'm sorry to have to ask, but I'm at a loss at this point, I've fixed this problem 3 times, and it keeps coming back.
AT&T tilt, unlocked, Solace 3.1 ROM
HardSPL 2.97
The phone works perfectly fine, except when I have to restart it, then it gets locked in the Bootscreen....and becomes very difficult to get it out. I try a soft reset, hard reset, nothing seems to work.
When this originally happened, I reloaded Solace 3.1 only to have it continue to be locked in the boot mode. Finally I I noticed the camera button and the power button appear to get locked into the on position, so i would manually create space between the button, and the actual activating button within the phone. It has worked 3/200 times I have had this problem. Overall I solved it by never restarting or resetting the phone, but eventually even with a ram cleaning program it becomes a problem.
If I'm thinking of the wrong solution let me know, it now appears to be stuck again in the on position for the power button....I basically ripped off the outer camera button, and now have to manually press the small one within the phone to activate it manually. I still can't get it off the bootloader, and its quite a frustrating problem.
Again, everything software wise works like a charm, I would have to think it isn't software related. Any ideas? I'm at a loss at this point, and using my phone from 2 years ago as a result.
Have U tried using another ROM besides the Solace ?
This is my second SGS with this problem and I am trying to determine if it is common or if I am just monumentally unlucky.
During normal use the bottom soft keys (menu and back) will become non-functional. One will stay lit and one will go out, but both will cease to work. Everything else on the phone is still responsive, sometimes the keys 'revive' themselves after a short period of time, other times I need to lock the phone to get them back.
I got this phone (a replacement) on the 6th, and this started on the 12th and has been happening more and more often ever since. Has anyone else seen this or have an idea what it may be? Or is this phone is destined to be my 2nd DOA in a month?
Here is a video showing the problem: '
you tube.com/watch?v=1s-wqWsHaIs
That is definitely not normal behaviour.
Exact same problem here; it seems to happen when I'm using the phone quite a bit but when I leave the phone alone for awhile, problem seems to go away then return because I'm using it too much.
// galaxy s
hol17 said:
Exact same problem here; it seems to happen when I'm using the phone quite a bit but when I leave the phone alone for awhile, problem seems to go away then return because I'm using it too much.
// galaxy s
Click to expand...
Click to collapse
FYI: Samsung support told me to return my phone.
It is almost like one of the soft keys gets stuck 'down', because it is the same behavior if you just hold down one of the keys. Mine seems to happen more when bluetooth is on and it comes and goes in spurts; good for an hour, bad for an hour, etc.
ETA: I am sure now that the soft keys are getting 'stuck down'. I have seen it 3 times now where I would press the left soft key and the light on the key will remain out, then after a second or so the quick search screen comes up and the left soft key light is still out.
any solution to this problem? i seem to have a slightly different issue
this just happened to me recently everything was working fine until this morning when i tried to press the menu and back buttons it wouldnt work, although the buttons light up and is registering my actions when i press them the light turns off and let go is lit up again.
could this be a software issue or something conflicting with my lednotification mod?
please reply ^_^
I've got the exact same issue with my soft keys getting stuck too. Just started a couple days ago, phone's less than a month old. I was also told to take my phone in for repairs.
Oh one tech support guy told me that Froyo might fix it... I'm kinda hoping for that, seeing as how this issue isn't exactly 100% reproducible for the warranty service department
I have the same problem its almost like the soft key is being held down, anyone find a fix for this?
Add me to the list
Add another one to the list. I too am experiencing this problem and I'm unfortunately screwed because of it. I attempted to return the phone, however the store in question refused to accept it because they tested it and found it had been unlocked. Two week old phone on stock FW bought outright ($600) and they won't replace it.
Unbelievable!
robcarey said:
Add another one to the list. I too am experiencing this problem and I'm unfortunately screwed because of it. I attempted to return the phone, however the store in question refused to accept it because they tested it and found it had been unlocked. Two week old phone on stock FW bought outright ($600) and they won't replace it.
Unbelievable!
Click to expand...
Click to collapse
Lock it back and go again.
I know this post it's a bit old, but i was harvesting the web looking for an answer to my problem that seems to be the same posted here.
I have a i9000T with eclair 2.1 and soft keys get stuck now and then. I couldn't find a way to reproduce this behaviour.
Recently (yesterday) i flashed a new 2.3.3 firmware hoping this curse to end. The problem seems to persist, but in some situations that i asume for a bad flashing (i didn't repartition neither wipe the phone before flash).
Anyway, can anybody tellme if this is a software or hardware issue? I'll have to return my phone or this is going to be 'fixed' with a nice flash?
Thanks.
cknu said:
I'll have to return my phone or this is going to be 'fixed' with a nice flash?
Thanks.
Click to expand...
Click to collapse
Only one way to find out mate.
You need to flash a 2.1 rom that consists of 3 files. 512 pit and re-partition.
Should get you back on track again.
I did flash it again with the 2.3.3 JVH, a few moments ago. Also did a repartition and wipe data and cache. It seems nice, but in a few minutes the same happend. Now, when i press the menu button it takes a nice screenshot of the phone. xD
I need to flash to a 2.1 version? Why is this? I thought flashing with any rom will work.
Thanks.
Solution to this problem!
Hey all - I found a solution to this problem - I can confirm this has fixed the problem on TWO phones for me - read the whole thread as this fix doesn't like custom firmwares, but works fine with all the regular FWs I've downloaded.
Works perfect - and simple fix!
http://forum.xda-developers.com/showthread.php?t=869492
^^^
Do not do this unless you have a i9000m. You will break your buttons.
electrotune1200 said:
^^^
Do not do this unless you have a i9000m. You will break your buttons.
Click to expand...
Click to collapse
Too bad i didn't see this before
I have I9000T used this 2663 method and now my soft buttons doesn't work anymore...
Didn't find a clear solution in the forums so i want to ask, like i said my phone is a I9000T with official 2.2.1 (UBPJA) rooted using SuperOneClick and unlocked editing the nv_data.bin file.
I was thinking on doing a hard reset to get back to the factory defaults but i see many ways of doing it that it gets confusing... i see peolple doing it through the privacy menu but i think that only erase data and doesn't restore anything OS wise, also see other people doing it using volume + home + power and selecting later clear storage, i think this is the same that the option in the privacy menu, and finally i see some people typing this code *2767*3855# what is the proper way to get back to the original OS in my case?
Thanks in advance...
I have had this galaxy gear for about a week now, and since new the camera has been extremely glitchy. Sometimes it will work no problem, but very rarely. Most of the time when I swipe down to use the camera the screen goes black and stays that way for almost a minute sometimes, before a message comes up saying "warning camera failed" . I have done a hard reset twice now, and made sure I had the latest software update, yet still haven't had any luck. I can still return it to the store for an exchange but best buy where I purchased it from is currently sold out and I am waiting. Just wondering if anyone else has had this problem and it might be fixable? I have read through a lot of forums but haven't found any information on this.
I have recently been trying to root, and install a custom rom hoping that would solve the problem. I follow the directions exactly from the forums in this site, it roots no problem, and I get the custom rom transferred to the galaxy gear sdcard using wondershare. But every time I get in recovery mode, and select recovery, it reboots and resets my gear. I don't get any options to install in twrp.
Can anybody help?
Gear camera problem
Walker1985 said:
I have had this galaxy gear for about a week now, and since new the camera has been extremely glitchy. Sometimes it will work no problem, but very rarely. Most of the time when I swipe down to use the camera the screen goes black and stays that way for almost a minute sometimes, before a message comes up saying "warning camera failed" . I have done a hard reset twice now, and made sure I had the latest software update, yet still haven't had any luck. I can still return it to the store for an exchange but best buy where I purchased it from is currently sold out and I am waiting. Just wondering if anyone else has had this problem and it might be fixable? I have read through a lot of forums but haven't found any information on this.
I have recently been trying to root, and install a custom rom hoping that would solve the problem. I follow the directions exactly from the forums in this site, it roots no problem, and I get the custom rom transferred to the galaxy gear sdcard using wondershare. But every time I get in recovery mode, and select recovery, it reboots and resets my gear. I don't get any options to install in twrp.
Can anybody help?
Click to expand...
Click to collapse
I facing the same issue also..Which "camera has stopped" problem. i had also send back to service center once and return back with a functional one. But today i once again had this problem and i try to remove out from my hand and twist abit on the belt and the camera able to function. i believe this is hardware problem and this was due to the belt problem. I think i going to send back to service center once again.
ongtinghou said:
I facing the same issue also..Which "camera has stopped" problem. i had also send back to service center once and return back with a functional one. But today i once again had this problem and i try to remove out from my hand and twist abit on the belt and the camera able to function. i believe this is hardware problem and this was due to the belt problem. I think i going to send back to service center once again.
Click to expand...
Click to collapse
Ya that's what I am thinking it must be, I will return mine too as soon as they get some more in stock. But I still haven't been able to figure out why I can root mine, but I cant install the custom recovery so I can install a new rom..
Mine just started doing this, anyone have a resolution other then returning it.
Never mind, i found the issue. The band has separated from the face and cut the cable to the camera.
how long did it take samsung to send you a new one.
After returning my watch to bestbuy I exchanged it for a new one. The new one the band is different and the hole in that was behind eh camera is now gone. I really think samsung is reading these forums
raiu said:
After returning my watch to bestbuy I exchanged it for a new one. The new one the band is different and the hole in that was behind eh camera is now gone. I really think samsung is reading these forums
Click to expand...
Click to collapse
can you post pictures?
I had the same problem.. did a fresh watch reset/recovery, and its fixed the problem.. not sure if it will for everybody, but in my case it did. My Model# is SM-V700
Step 1: Make sure Gear is powered off
Step 2: Press and hold the power key until you see either the Galaxy Gear rebooting… screen or a blank white screen.
Step 3: Release the power key and then continuously tap the power key until you see the Reboot Select Mode screen.
Step 4: Tap the power key to highlight the "recovery" option.
Step 5: Long press the power key (5-8 sec) to select it.
Solution to camera stopped problem
I hope this helps others. I had not used the watch in many months. I couldn't get it to turn on after a whole day of charging. Read a tip off an Amazon review and it worked -- if your watch is "dead" plug the charging cable into your computer USB port and not the AC outlet. It charged just fine then and works.
Now to the camera problem. I reset the watch and reinstalled. Got the "black screen" and after so many seconds, a message 'camera stopped'. Reset again. Still the same problem.
But I got into the GEAR MANAGER , selected MY APPS and noticed that there was a "+" sign on the top right of the screen. Touched that and it brought up an additional list of apps. At the top it said I has "11/14" apps turned on. I found I could click on the CAMERA and it went to 12/14. Picked 2 more things. Now the Camera is one of the 14 apps on the device. Guess there's a limit
THE CAMERA WORKED PERFECTLY AFTER THAT.
I have got my Asus ROG Phone II for about 8 months and I have recently got some problems with the software. The phone suddenly turns off on it's own, when I am using it and stucks at the restarting process with Asus Logo and the loading bar on the lower side but doesn't open, even if I wait for a full whole hour. I have to press volume down + power off button to make it work again. I wanted to ask if any of you guys have got the same problem, or any clues how to solve it?
Well I had rooted my phone after a month of it's use and unrooted it. For about 2 Months before, my charging port stopped working and Asus Service Center fixed it, and I guess they somehow flashed my Phone, as I not don't have to download and install the new firmware. It was good in a way but I feel it is getting some lag during the use of certain apps and the problem which I mentioned earlier. I would be thankful and grateful for your replies.
Wishing all to stay safe and healthy
Fantasticooo said:
I have got my Asus ROG Phone II for about 8 months and I have recently got some problems with the software. The phone suddenly turns off on it's own, when I am using it and stucks at the restarting process with Asus Logo and the loading bar on the lower side but doesn't open, even if I wait for a full whole hour. I have to press volume down + power off button to make it work again. I wanted to ask if any of you guys have got the same problem, or any clues how to solve it?
Well I had rooted my phone after a month of it's use and unrooted it. For about 2 Months before, my charging port stopped working and Asus Service Center fixed it, and I guess they somehow flashed my Phone, as I not don't have to download and install the new firmware. It was good in a way but I feel it is getting some lag during the use of certain apps and the problem which I mentioned earlier. I would be thankful and grateful for your replies.
Wishing all to stay safe and healthy
Click to expand...
Click to collapse
Don't know what the problem is, but you've posted this in the wrong section!
I think I am in a similar situation. My phone's problem is that it kind of crash while booting up (stange lines shows on the screen like some glitch) , it doesnt boot up normally and it loops 3 to 4 times until it's left on a black screen. I am not sure of its status at this point for it is not responsive even to force restart (Vol down + Power) but it does work only once in a couple of minutes and proceeds to bootloop and back again to the black screen. I haven't rooted it but i did flash it from CN to WW which was successful and was using it perfectly for 4 months up until this situation. I dont know what exactly is the problem. Can anyone help me?
Same with me bro... Mines already bricked because of flashing it to the original version
Same here