Frustration at it's peak. - Galaxy S I9000 Q&A, Help & Troubleshooting

Hi there guys, That's it .
After reaching my highest limit of searching / installing / removing , z4root , super onclick, which btw none work, I am on the edge, basically , loosing my mind, and all I would like to do is just root my phone and have it working properlly and faster.
Now there are so many old root methods as the one I tryed Does any of you guys can help me out and explain how do I root my Samsung Galaxy S I-9000, with froyo 2.2 firmware ?
Thank you Omri.

what exact firmware,
i used JL2 and super one click worked for me.
try all of them.

Gets stuck on " Waiting for Device "
and i already unplugged the phone a couple of times with usb debugging on/off , any chance that im doing somthing wrong?

flash speedmod kernel.. or cfroot kernel

Can you see phone from the PC?
It sounds like the Odin method of flashing a custom kernel is not an option (if not try that - lots of info in the kernel posts)?
If your computer is not recognizing the phone try remove and reinstall drivers and kies and then also clean out the port on the phone with alcohol (and try another usb cable if you have one).
That my two bits. I tried in vain to root from the phone alone with 2.2 but finally got odin working by cleaning the port and now the possibilities are endless.

What exactly is this "Flashing / Kernel" options exactly , because the computer recognizes the USB just fine. ??

See here
http://forum.xda-developers.com/showthread.php?t=822756
This is for speedmod (if you need other options go to the stickies in the development section and look for the kernel list near the bottom of the stickies).
Follow the procedure for Odin installation. You will need to ensure you can go into download mode (Vol Down, home and power buttons to see - it should show android with a shovel in yellow - you can pull the battery to stop it if just checking but don't touch anything while Odin is working). If you cannot get 3 button download working, look for that fix in the forums too. I did not have that issue so I can't point you in the right direction there.
I think hardcore's page (author of the rom) has a link to an Odin guide. But its worth getting to know a bit as it will save your bacon if you need to get back to stock for warrenty.
Once you have this rom you'll be rooted and have clockwork Mod which allows flashing from the phone if you like (most custom roms are based on CWM installation). This is what I did once I got mine back from warrenty with 2.2 and then I flashed Darky's rom keeping the stock modem.

juvenileomri said:
Gets stuck on " Waiting for Device "
and i already unplugged the phone a couple of times with usb debugging on/off , any chance that im doing somthing wrong?
Click to expand...
Click to collapse
If you are stuck at "waiting for device"
do not exit Super One Click
1. pull out the usb from the phone,
2. turn off by pulling out the battery
3. put the battery back, turn on & plug in the USB

Related

unsuccesfull vibrant flashing on captivate

hello have flashed virant android 2.1 russian on the captivate due to mistake after that volume button and screen rotation problems i had. i was recomended to flash captivate kernel - i donloaded it and flashed it with mistake - i think i flashed in in wrong place ( i do not remember if i chose PDA, CSC, or PHONE) after that i have a big problem i downloaded one clock odin make phone into download mode by pressinf 2vol buttons, inserting usb cable, than the battery - because other ays i cant enter download mode in odin one clock com4 recognizes i pusg start button but nothing after @DO NOT TURN OFF [email protected] notice is done phone still with the yellow android man in triangle and nothing happens, please help me to solve it i searched this captivate forum for half of a day but no answed found my phone is brick for now and i need a phoen for my work
is there any wariant for reflashing it?
by the way i tried to reflash it by odin vith the vibrant firmware it flashed but on first startup screen gone with different dots on it ( like bad tv signal on television) than it flashed and started but still with that problems can i go back to any working captivate firmware? and how? thanks
maxxis said:
hello have flashed virant android 2.1 russian on the captivate due to mistake after that volume button and screen rotation problems i had. i was recomended to flash captivate kernel - i donloaded it and flashed it with mistake - i think i flashed in in wrong place ( i do not remember if i chose PDA, CSC, or PHONE) after that i have a big problem i downloaded one clock odin make phone into download mode by pressinf 2vol buttons, inserting usb cable, than the battery - because other ays i cant enter download mode in odin one clock com4 recognizes i pusg start button but nothing after @DO NOT TURN OFF [email protected] notice is done phone still with the yellow android man in triangle and nothing happens, please help me to solve it i searched this captivate forum for half of a day but no answed found my phone is brick for now and i need a phoen for my work
is there any wariant for reflashing it?
by the way i tried to reflash it by odin vith the vibrant firmware it flashed but on first startup screen gone with different dots on it ( like bad tv signal on television) than it flashed and started but still with that problems can i go back to any working captivate firmware? and how? thanks
Click to expand...
Click to collapse
Hello maxxis.
I actually run in to this all of the time. Odin *never* works the first time for me. It basically hangs and I have to screw with unplugging and plugging in my phone.
Do not take this as advice, this is what I have done and it works on my phone:
0) Make sure the 3 button combo gets you in to download mode. If not, stop, find a 3 button fix and make sure it works or make a jig: http://forum.xda-developers.com/showthread.php?t=841512
1) Start Odin. Wait for it to get ready.
2) Put your phone in download mode
3) Plug in your phone to a USB cable connected to the BACK of your MOTHERBOARD - no add-in cards, hubs, front ports or any other nonsense.
4) Try to flash with Odin. If it hangs, remove your phone, reboot and put back in download mode and try again. Do not unplug it if it is doing anything.
This usually works on my second or third try. Good luck!
You need to do a master clear. Or format the internel SD. Then flash vibrant rom.
Or try his post lol. I was too slow i guess
but i have captivate if i flash vibrant rom again it will not work correctly

[Q] Semi bricked I9000

Hello everyone,
Two days ago I try to make a firmware update to Gingerbread trough Kies.
After everything is finished the phone start, shows the main logo (the white one), start that animation with "S" and come on a black screen. Time to time he vibrate 2 or 3 times and only the back and menu buttons are illuminated.
1. Cannot use 3 buttons to get into download or recovery mode
2. Cannot put the phone in USB debugging (obviously)
3. For unknown reason I cannot instal ADB drivers (win7 shows the yellow triangle)
4. Samsung drivers are installed on Modem and USB (shows Samsung)
5. On "devices" , can be seen but again no ADB
6. ODIN see it on com8 but again for some reasons it wont work (probably because he work in download mode )
7. SDK is installed
8. ADB shows "no devices found"
9. No other button combination works (home+down , up+down +battery in + USB plugged ... etc)
Any suggestion/help ?
Thank you very much for reading and hopefully Ill get some help
Best regards,
Andrew
Have you tried "emergency reset" or whats it called in Kies?
Did you have the 3-button combo before the flash?
If so try to remove the battery and then with it removed press the combo and insert the battery-
Maybe you refer to that in number 8?
A JIG will for sure help you to get into download mode.
Good luck.
/qsec
Hello and thank you,
3 buttons combo didnt work before
Kies stays with the status "connecting" but no phone shows up in it.
Thankx,
Andrew
You in the UK .
Gingerbread no update via Kies its not released yet .
Kies has Firmware recovery or some such tab.
Was your phone lagfixed ..
Did your phone have custom rom .
Current condition of phone looks like you need download recovery jig from front page .
Or if no lagfix no custom rom then Samsung service centre failed Kies flash .
jje
Yes lag fixed OCLF
And Kies said something about firmware update. I do have Froyo 2.2 and the logical thing was Ginger so thats why i thought it is.
Thank you,
Andrew
antraian said:
Yes lag fixed OCLF
And Kies said something about firmware update. I do have Froyo 2.2 and the logical thing was Ginger so thats why i thought it is.
Thank you,
Andrew
Click to expand...
Click to collapse
Lagfix a no no thats what F*** your phone .
Froyo 2.2 next update 2.2.1
Download recovery jig .
jje
JJEgan said:
Lagfix a no no thats what F*** your phone .
Froyo 2.2 next update 2.2.1
Download recovery jig .
jje
Click to expand...
Click to collapse
Never had any problems with lagfix, but i guess if you do things in the wrong order without removing it before upgrading.
OP, did you follow any instructions, or just do it blind?
Never had any problems with lagfix
Your choice but failing to remove lagfix before flashing is a well posted problem on XDA .
jje
This is very true.
It was stupid of me flashing with lag fix installed evendo I read that YOU MUST remove lagfix before do it ....
Cheers,
Andrew
antraian said:
This is very true.
It was stupid of me flashing with lag fix installed evendo I read that YOU MUST remove lagfix before do it ....
Click to expand...
Click to collapse
Worse, you flashed without enabling 3 button combo prior. Due to that you're unable to get into download nor recovery mode unfortunately. So unless that emergency firmware option in Kies won't help you will have to build or buy yourself a jig dongle/cable which is plugged into the phone by USB to force download mode. Check on ebay UK, there are surely some people selling professionally built ones for just a few pounds (got one myself from US for just $7 or so).
Once you have that, re-flash with Odin.
And once your phone is OK again, get that 3 button combo working! I used this method successfully. Soft bricked the first time thanks to using USB hub instead of direct USB as it wasn't mentioned in the stickies sadly. Yet thanks to the Jig I got prior I tried again and flashed my phone to enable 3 button combo forever.
P.S.: there is something else very vital I came across recently and am glad I saw it in time: backup of the /efs folder which contains IMEI etc:
http://forum.xda-developers.com/showthread.php?t=859914
(I hope that's mentioned in the stickies somwhere but if so I would have seen it unless I missed one)
After reading in these forums for hours before trying my very first flashing I might want to write a comprehensive guide...

[Q] Captivate Soft Brick - Need a rooted Odin solution.

Hi
My brother (a no-geek) has a captivate, and lives in a different city (I donot have physical access to the phone). He visited me few weeks ago and I installed CM-7 on his phone, i know my bad. Some of his videos were not working, so i asked him to update to the latest CM-7 build. He download the build, saved it on int sd_card and used ClockWork Recovery to install the selected ROM. Upon reboot it entered in never-ending splash screen. I found couple of odin ROMs, and posted him link, we tried to flash them, but no good.
Status --
The COM ports are detected, but the process at times halts at <SET PARTITION> at times at <SET UP>... at times all thread completed successful would show up as soon as hitting START.
I dont have a captivate, can someone please suggest a sure shot solution and post me a link for ODIN, with a root rom. I am using Team Whiskey on my Vibrant, and I prefer stable modified ROM because of its features and power.
I can explain him the process on skype using desktop sharing, but the ROM should be good. Thankyou very much in advance.
if he can access recovery, try wiping everything thru recovery then start again
Phone is in Soft Brick state.
Phone is in Soft Brick state. So i cannot boot into the phone and go to CW recovery.
What he needs is just a stable usb connection that's how he got to this point, bad communication between the phone and computer. On cm7 I beleive you need the nexus s drivers installed. Also make sure it's plugged into a usb port that's attached directly to the motherboard (back of pc, port 1 on laptop)
@studacris
I think the drivers are already installed good. The connection is also good, as i can the COM port detection in the ODIN, with one of the boxes changing its colour from NO-COLOUR to YELLOW-COLOUR.
I think the ROM builds are not good. They go action-less during flashing, actually nothing (progress bar) comes on phone, it keeps showing the Downloading screen, endlessly. Odin usually is stuck at at <SET PARTITION> at times at <SET UP>...
Can someone post a link for a test one click odin. Well i would prefer one click.
You did try DG's JF6 one click, thats the only one I use, how are you establishing dowload mode on the phone or are you even doing this.
REMY4223 said:
I would suggest to Odin back to stock then update to Froyo via Kies.
Click to expand...
Click to collapse
if you could do all that, why would you need to send back for a new phone ? If you could do any of that, the OP wouldn't be in a non-functioning predicament
Ragin Caucasian said:
if you could do all that, why would you need to send back for a new phone ? If you could do any of that, the OP wouldn't be in a non-functioning predicament
Click to expand...
Click to collapse
+1 If you read the OP the problem is he can't flash back to stock he is having problems flashing anything period, @ the OP correct me if I'm wrong but I have a strong hunch that you are leaving out some pretty crucial steps, I have a feeling that you are not putting the phone into download mode, I also believe that you are gonna need to make a jig and pay a visit to your brother to help him out especially if its bricked the same way mine just was flashing with cm7 roms. But if you are getting a com port to show without having to put in download mode then you are farther along in the boot process. If this is the case you may be able to adb into recovery do a full wipe excluding /boot and reflash. Will the PC recognize the phone with it in its current boot locked state? If so then recovering should be somewhat of a breeze.
http://forum.xda-developers.com/showthread.php?t=829392 read this post it may help otherwise there are tons others
- I am getting to downloading mode by
--- pressing the "vol +" and "vol -" buttons and then connecting the usb cable to the computer.
--- then removing the cable, after the phone enters the download mode. Then, start the odin and connect the phone through usb cable again. The odin detects the phone on one of the COM port.
- I havent tired wiping the phone through recovery. But i need to get to recovery first. I dont know in a soft brick state if i can get into recovery.
- regarding getting back to 2.1... i would like to flash to the latest version. Kies update is not an option for me, as i not in US.
This phone was purchased from craiglist, i used one click root method to root it and the same script an option to get the unlock codes. After that i experimented a lot on the phone with various scripts. Last i was using congnition on it. Then saw CM7, i liked it on my vibrant, so i flashed it on my captivate (which i got for my brother). Now i have to get back to some stable modified ROM... I am thinking about trying Srendipity or cog ROM... but before than i have to install a rooted stock ROM.
That is the story and issue... but thanks a lot for help. Any more suggestions.
viveksharma2108 said:
- I am getting to downloading mode by
--- pressing the "vol +" and "vol -" buttons and then connecting the usb cable to the computer.
--- then removing the cable, after the phone enters the download mode. Then, start the odin and connect the phone through usb cable again. The odin detects the phone on one of the COM port.
- I havent tired wiping the phone through recovery. But i need to get to recovery first. I dont know in a soft brick state if i can get into recovery.
- regarding getting back to 2.1... i would like to flash to the latest version. Kies update is not an option for me, as i not in US.
This phone was purchased from craiglist, i used one click root method to root it and the same script an option to get the unlock codes. After that i experimented a lot on the phone with various scripts. Last i was using congnition on it. Then saw CM7, i liked it on my vibrant, so i flashed it on my captivate (which i got for my brother). Now i have to get back to some stable modified ROM... I am thinking about trying Srendipity or cog ROM... but before than i have to install a rooted stock ROM.
That is the story and issue... but thanks a lot for help. Any more suggestions.
Click to expand...
Click to collapse
Try putting the phone into download mode after you open Odin. Which version of Odin is this? Also, installing the nightly build of CM7 again often fixes the boot loop on the newer builds. I would try that if you can get to recovery.
Sent from my SGH-I897 using XDA Premium App

[i9000b] BSOD - Phone ! Computer Screen

I had Android 4.0.3 (IceCream Sandwich) on my Galaxy S GT-I9000B (I did install it through Odin, nothing went wrong), but is was laggish (too much for it to handle, I think) and after a few months, I decided to roll it back to 2.3.3 (Gingerbread).
I started the process to install the firmware through Odin3 v1.85 - the file I download (from sammobile.com/firmware, had only one file that I used on the PDA space.
Odin recognized my phone and I started to install it, but after a while my phone was stuck on the downloading screen (2 hours of installation, I tought that something went wrong).
I then turned my phone off to try and install again, but when I turned it on, there were a Phone - exclamation mark - Computer Symbol.
I can get it to dowlonad mode (Volume Down+Home+Power), but when I plug it to the pc, it says "unknown device" and it can't find drivers for it.
I think I have the latest drivers from Samsung (I had from Kies and I re-downloaded a file somewhere from this forum named SAMSUNG_USB_Driver_for_Mobile_Phones_1_5_6_0.exe).
It appears that since windows can't install the drivers, Odin doesn't recognize the device - it was recognizing it before, when I was installing the firmware.
Now I'm stuck - I tried anything I saw in this forum and in other places - I did even pray for a miracle, but it didn't work
I know that there must be a way, but I don't know how.
Before I forget, I'm using Windows 7 Ultimate x64.
If you can get it in download mode everything should be fine, I've had a problem like this, my pc couldn't see the phone in download no matter what. Try to use another USB port, better another PC. Also I've heard that x64 doesn't get along well with Odin. If possible you can try Linux and Heimdall, after all Android is Linux too.
KainFromNod said:
I know that there must be a way, but I don't know how. Before I forget, I'm using Windows 7 Ultimate x64.
Click to expand...
Click to collapse
Ok, k4Z3666, has given you a starting point...the phone is still in download mode but without a booting ROM, so its OK, the problem is your PC, USB cable or USB port. If you want to be quick about it, just try on a lap top..if not a simple Reboot of PC ( after removing power cord) and Phone (after a battery Pull), and a switch to a different USB port at the back of PC can solve this for some...for other solutions try these http://forum.xda-developers.com/showpost.php?p=27205737&postcount=4571 anything else you may need can be found on My Android collections., link below
k4Z3666 said:
If you can get it in download mode everything should be fine, I've had a problem like this, my pc couldn't see the phone in download no matter what. Try to use another USB port, better another PC. Also I've heard that x64 doesn't get along well with Odin. If possible you can try Linux and Heimdall, after all Android is Linux too.
Click to expand...
Click to collapse
I tried other USB Ports and also rebooting. It was working just fine - it seems like a driver problem to me.
My notebook is dead, but I'll try using someone else computer.
Does Odin runs in Windows XP? I might try it in my virtual box - I doubt that it will work, but it is the best thing I have to do untill tomorrow.
I got it working in my mother's notebook - should I try something different? I only have the PDA, should I try a PIT?
I don't know what those do, but I read somewhere that PIT is used to recover bricked phones.
EDIT: I installed only the PDA, it worked fine on the 2nd time (first time, it got stuck but I could make it work changing the usb port and cable).
Now it is on loop - it repeats the samsung logo over and over again. Any ideas now?
KainFromNod said:
Now it is on loop - it repeats the samsung logo over and over again. Any ideas now?
Click to expand...
Click to collapse
what ROM did you use? Did you do any wipes?
Opps..you got an i900B, so make sure you are only using I9000B ROMS as i9000 is not compatible with your phone
Follow guidelines from here
http://forum.xda-developers.com/showthread.php?t=919219
http://forum.xda-developers.com/showpost.php?p=22941192&postcount=300
KainFromNod said:
Now it is on loop - it repeats the samsung logo over and over again. Any ideas now?
Click to expand...
Click to collapse
Assuming that you're on the right rom for your phone can you enter recovery mode? Try reinserting battery, and enter recovery with [vol+, menu button, power on]
KainFromNod said:
I got it working in my mother's notebook - should I try something different? I only have the PDA, should I try a PIT?
I don't know what those do, but I read somewhere that PIT is used to recover bricked phones.
EDIT: I installed only the PDA, it worked fine on the 2nd time (first time, it got stuck but I could make it work changing the usb port and cable).
Now it is on loop - it repeats the samsung logo over and over again. Any ideas now?
Click to expand...
Click to collapse
Yep if u want to back to stock u need pit file because ICS use different system file
Why u don't like ICS ? Its way better and faster than sammy ROM even its more stable , I think u should try it again with devil kernel with oc to 1.2 it will fly u can add some live oc which will give more fluidity
Sent from another galaxy powered by CM10 & Syiah
Ok, I'm posting it here just to leave a reply and reference for future generations, as my problem was solved.
xsenman said:
what ROM did you use? Did you do any wipes?
Opps..you got an i900B, so make sure you are only using I9000B ROMS as i9000 is not compatible with your phone
I used a firmware from my country (available here: sammobile.com/firmware/?page=3&model=GT-I9000B&pcode=ZTO&os=1&type=1#firmware) and I wiped the cache (I'm not sure what this means, but I believe it is the 2 options on volume up+menu+power)
Follow guidelines from here
http://forum.xda-developers.com/showthread.php?t=919219
http://forum.xda-developers.com/showpost.php?p=22941192&postcount=300
Click to expand...
Click to collapse
k4Z3666 said:
Assuming that you're on the right rom for your phone can you enter recovery mode? Try reinserting battery, and enter recovery with [vol+, menu button, power on]
Click to expand...
Click to collapse
I was entering recovery mode, but it was giving me some error when I tried to wipe the 2 things that I forgot the name =/
yahyoh said:
Yep if u want to back to stock u need pit file because ICS use different system file
Why u don't like ICS ? Its way better and faster than sammy ROM even its more stable , I think u should try it again with devil kernel with oc to 1.2 it will fly u can add some live oc which will give more fluidity
Sent from another galaxy powered by CM10 & Syiah
Click to expand...
Click to collapse
ICS wasn't faster here - it was laggish and always crashed some common apps (gallery, music player). I believe that the firmware wasn't completely "done" as it was being adapted from another version (my phone is brazilian) and some functionalities that it has (i.e. digital TV) wasn't available.
What I done to correct the boot was simple (I found a tutorial in a brazilian site, so it had all the roms that I needed).
1) Used a PIT and a stock rom to get it back to factory version;
2) Upgraded to Froyo (original) - That was kind of a mistake, the tutorial said to do it because then KIES would update it automatically to Gingerbread. The phone was fully functional, but KIES said that it couldn't update it (it recognized the phone and everything).
The tutorial stoped there, but since I had the ROM, I used Odin to install Gingerbread (the one that was looping) and it was done.
Now I need to remember how to root it because there are some dumb apps who can't get away (i.e. Orkut app, some demo games).
Thank you all for the help!
KainFromNod said:
I was entering recovery mode, but it was giving me some error when I tried to wipe the 2 things that I forgot the name =/
Click to expand...
Click to collapse
From recovery you can always try to flash another kernel, that would probably resolve things too. Anyways the problem's solved, glad to help

[Q] N7000 bricked - No USB connection possible

ok first things first, imma noob, and i did a stupid thing.
It started in last summer when i wasnt able anymore to connect the N7000 to my WIN 7 64bit (probably after an update to ICS /JB).
Well since i never needed to transfer files (64GB-sdxc) i didnt care much about it. but then in last times my phone/ram cache was full of so much unblockable bootloaded crapware so that i wanted to switch from a official 4.1.2 firmware to cyanogen. But since my USB wasnt working it wasnt that easy.
Side note: the USB-port was ****ed up before (short-circuit, screen woke up due to fake-loading). i fixed that by luck and some dark magic.. so of course i thought the connection problem were because oif the broken jack.
The day before yesterday i tried for 8 hours anything i could find to install another bootloader and flash CM (CWM / TWRP / Triangle away / minimal adb/fastboot etc.); didnt work, CWM seemed to boot up but loading failed all the time at 1/3rd of the bar at screen went black.
Yesterday my friend came over and i tried to use his USB-jack to connect my phone to my Pc, which failed. THEN i put the "broken" one from mine in his N7000; that was efficacious, everything worked fine, so the USB-jack wasnt the problem.
Later i had, out of frustration, moronism, and anger, the glorious idea to download and flash another (older) Kernel via mobile odin to install an old gingerbread stock rom on it afterwards.
That was stupid as i know now, all i can do now is enter download mode, but without USB-connectivity and the stock bootloader with the options reboot system / update from sd / wipe data / wipe cache / test redbend fota(FS) and boot, which stucks at the N7000-screen.
After i managed to **** things up i found an article which describes my (now former) USB-problem perfectly. it says to put in a special number combination on the phone to get to phoneUtil and then switch from modem mode to pda mode. i knew this screen before but i couldnt find it at the preferences on JB.
Now comes my question: What could be done to unbrick my phone? is there any help?
Can you not try another USB cable? Try cleaning out the pins and see if it works. Then flash speedmod.
Sent from my GT-N7000 using Tapatalk
backstreetboy said:
Can you not try another USB cable? Try cleaning out the pins and see if it works. Then flash speedmod.
Sent from my GT-N7000 using Tapatalk
Click to expand...
Click to collapse
>Just to clarify: with USB-Jack i mean the USB-Port with the connector to the motherboard; sorry if i misused the word
I dont think so cause we used only his cable when he was here and my phone neither connected with mine nor with his USB-Jack, but both Jacks worked on his phone.
Pro-question: Is there a difference between (usual) USB-connection in booted mode and connection in download mode? i mean is download mode something like a "safe mode" where the USB doesnt need to run on 100% availabilty? Should i try to find the phone via Odin in downdload mode again by using his cable? i dont think this could work else.
Samsung galaxy note gt-n7000 bricked. Need HELP!!
The phone shows " Firmware upgrade issue encountered an issue. Please select recovery mode in Kies & try again". I cant go to recovery mode ie. vol up+home+power. THings I have tried:
1. with Kies the device isnt recognised. I have updated the driver as well.
2. with odin every thing fails... flashing "all samsung recovery.tar", flashing stock jelly bean, flashing .pit file
I have googled for days and tried many things but isnt working. Need help

Categories

Resources