unsuccesfull vibrant flashing on captivate - Captivate Q&A, Help & Troubleshooting

hello have flashed virant android 2.1 russian on the captivate due to mistake after that volume button and screen rotation problems i had. i was recomended to flash captivate kernel - i donloaded it and flashed it with mistake - i think i flashed in in wrong place ( i do not remember if i chose PDA, CSC, or PHONE) after that i have a big problem i downloaded one clock odin make phone into download mode by pressinf 2vol buttons, inserting usb cable, than the battery - because other ays i cant enter download mode in odin one clock com4 recognizes i pusg start button but nothing after @DO NOT TURN OFF [email protected] notice is done phone still with the yellow android man in triangle and nothing happens, please help me to solve it i searched this captivate forum for half of a day but no answed found my phone is brick for now and i need a phoen for my work
is there any wariant for reflashing it?
by the way i tried to reflash it by odin vith the vibrant firmware it flashed but on first startup screen gone with different dots on it ( like bad tv signal on television) than it flashed and started but still with that problems can i go back to any working captivate firmware? and how? thanks

maxxis said:
hello have flashed virant android 2.1 russian on the captivate due to mistake after that volume button and screen rotation problems i had. i was recomended to flash captivate kernel - i donloaded it and flashed it with mistake - i think i flashed in in wrong place ( i do not remember if i chose PDA, CSC, or PHONE) after that i have a big problem i downloaded one clock odin make phone into download mode by pressinf 2vol buttons, inserting usb cable, than the battery - because other ays i cant enter download mode in odin one clock com4 recognizes i pusg start button but nothing after @DO NOT TURN OFF [email protected] notice is done phone still with the yellow android man in triangle and nothing happens, please help me to solve it i searched this captivate forum for half of a day but no answed found my phone is brick for now and i need a phoen for my work
is there any wariant for reflashing it?
by the way i tried to reflash it by odin vith the vibrant firmware it flashed but on first startup screen gone with different dots on it ( like bad tv signal on television) than it flashed and started but still with that problems can i go back to any working captivate firmware? and how? thanks
Click to expand...
Click to collapse
Hello maxxis.
I actually run in to this all of the time. Odin *never* works the first time for me. It basically hangs and I have to screw with unplugging and plugging in my phone.
Do not take this as advice, this is what I have done and it works on my phone:
0) Make sure the 3 button combo gets you in to download mode. If not, stop, find a 3 button fix and make sure it works or make a jig: http://forum.xda-developers.com/showthread.php?t=841512
1) Start Odin. Wait for it to get ready.
2) Put your phone in download mode
3) Plug in your phone to a USB cable connected to the BACK of your MOTHERBOARD - no add-in cards, hubs, front ports or any other nonsense.
4) Try to flash with Odin. If it hangs, remove your phone, reboot and put back in download mode and try again. Do not unplug it if it is doing anything.
This usually works on my second or third try. Good luck!

You need to do a master clear. Or format the internel SD. Then flash vibrant rom.
Or try his post lol. I was too slow i guess

but i have captivate if i flash vibrant rom again it will not work correctly

Related

Stuck in the infamous connect phone to PC screen - Please help

HI,
I'm a complete newbie with the Android (power user in WM).
Using SGS i9000 with origin German ROM I9000XXJF3.
I was trying my first ROM reflash, but something seems to be very wrong.
This is what I did:
1. I rooted the device successfully using that guide: http://forum.xda-developers.com/showthread.php?t=728754
2. Downloaded and install from the market busybox
3. Then I followed the guide here: http://samsung-firmware.webs.com/Flash guide english.pdf .
Important, I was trying to install the ROM: I9000JPJG8 BUT with PIT 513
4. ODIN announced (on blue background ): reset, and the device returned into recovery mode (same I used for rooting the device).
5. I was trying to repeat the process, this time with PIT 512 with the same ROM.
6. It seems to successful. I saw the glowing Galaxy S, for sometime, then the device turned itself off.
Now all I get is the connect to PC (phone, orange exclamation mark & PC logos) logo.
I was trying to pull the battery out, restarted the PC, and was trying to reconnect to ODIN, but ODIN does not recognize the device.
I was trying to select in ODIN only "auto reboot", press start, but again nothing happened.
Very frustrating for a start.
Any help would be greatly appreciated.
Amir.
Shalom amir,
go back to download mode and reflash with odin (512 pit). Should do the trick.
I've experienced the same thing before. I thought I bricked the phone but that wasn't the case.
Try to reflash your SGS on another computer. This PC that you used won't be able to find your SGS anymore until you successfully flashed it.
mike.sw said:
Shalom amir,
go back to download mode and reflash with odin (512 pit). Should do the trick.
Click to expand...
Click to collapse
Hi Mike,
After numerous times, I've managed to return to downloading mode
I've achieved that by inserting the battery, while pressing vol down+power+home.
Now was able to reflash, and everything is good.
cavinsoo said:
I've experienced the same thing before. I thought I bricked the phone but that wasn't the case.
Try to reflash your SGS on another computer. This PC that you used won't be able to find your SGS anymore until you successfully flashed it.
Click to expand...
Click to collapse
I did that too, but the problem was how to return to downloading mode..
Almost had a heart attack...
Thanks anyway guys!
I have been stuck on that screen more than I like but have found this to work the best.
1 - power down the device and remove battery / usb connection
2 - connect usb
3 - hold the volume up key while moving to step 4
4 - insert battery
I end up in the download screen everytime and then must start the Ordin3 flash quickly otherwise it just hangs on the download. I appears if I start the download within 15 seconds, works like a charm.
RickCain said:
I have been stuck on that screen more than I like but have found this to work the best.
1 - power down the device and remove battery / usb connection
2 - connect usb
3 - hold the volume up key while moving to step 4
4 - insert battery
I end up in the download screen everytime and then must start the Ordin3 flash quickly otherwise it just hangs on the download. I appears if I start the download within 15 seconds, works like a charm.
Click to expand...
Click to collapse
You are SUCH A LIFE SAVER!!! I tried every other thing on xda and youtube but the above steps are the only one that worked on my vibrant. The trick is to start ODIN ASAP after step 4 and start the flash (after selecting PIT and PDA file) or it won't work if you take your time
This happemed to me too nuty phone was going ibto download mode so I just reflashed it with 2.3.4
Sent from my sgs
kernel: galaxian
Rom: jetpack

Frustration at it's peak.

Hi there guys, That's it .
After reaching my highest limit of searching / installing / removing , z4root , super onclick, which btw none work, I am on the edge, basically , loosing my mind, and all I would like to do is just root my phone and have it working properlly and faster.
Now there are so many old root methods as the one I tryed Does any of you guys can help me out and explain how do I root my Samsung Galaxy S I-9000, with froyo 2.2 firmware ?
Thank you Omri.
what exact firmware,
i used JL2 and super one click worked for me.
try all of them.
Gets stuck on " Waiting for Device "
and i already unplugged the phone a couple of times with usb debugging on/off , any chance that im doing somthing wrong?
flash speedmod kernel.. or cfroot kernel
Can you see phone from the PC?
It sounds like the Odin method of flashing a custom kernel is not an option (if not try that - lots of info in the kernel posts)?
If your computer is not recognizing the phone try remove and reinstall drivers and kies and then also clean out the port on the phone with alcohol (and try another usb cable if you have one).
That my two bits. I tried in vain to root from the phone alone with 2.2 but finally got odin working by cleaning the port and now the possibilities are endless.
What exactly is this "Flashing / Kernel" options exactly , because the computer recognizes the USB just fine. ??
See here
http://forum.xda-developers.com/showthread.php?t=822756
This is for speedmod (if you need other options go to the stickies in the development section and look for the kernel list near the bottom of the stickies).
Follow the procedure for Odin installation. You will need to ensure you can go into download mode (Vol Down, home and power buttons to see - it should show android with a shovel in yellow - you can pull the battery to stop it if just checking but don't touch anything while Odin is working). If you cannot get 3 button download working, look for that fix in the forums too. I did not have that issue so I can't point you in the right direction there.
I think hardcore's page (author of the rom) has a link to an Odin guide. But its worth getting to know a bit as it will save your bacon if you need to get back to stock for warrenty.
Once you have this rom you'll be rooted and have clockwork Mod which allows flashing from the phone if you like (most custom roms are based on CWM installation). This is what I did once I got mine back from warrenty with 2.2 and then I flashed Darky's rom keeping the stock modem.
juvenileomri said:
Gets stuck on " Waiting for Device "
and i already unplugged the phone a couple of times with usb debugging on/off , any chance that im doing somthing wrong?
Click to expand...
Click to collapse
If you are stuck at "waiting for device"
do not exit Super One Click
1. pull out the usb from the phone,
2. turn off by pulling out the battery
3. put the battery back, turn on & plug in the USB

i9000 bricked, but goes to download mode - rescuable?

So here't the full background, it's not long, please read:
http://www.darkyrom.com/community/i...-bricked-my-sgs-wonder-what-i-did-wrong.2032/
Long story short, it looks like I bricked my SGS when trying to flash with Odin, even though I followed the tutorial very closely. When I power up the phone, it just gives me the image with phone, exclamation mark and PC on it. It does, however, go into download mode when powered up with VolDown and center button.
How do I save it? Do I need the JIG (God, please say no! )
Have you tried reflashing with odin.
Jig is only needed when you cant get into download mode.
Also i just looked inside the darky rom topic.
Have you flashed the jvk rom first with the bootloaders?
Edit: as said below. If you gonna reflash, flash a stock rom. Not the darky rom. First priority is to make your phone work.
Sent from my GT-I9000 using XDA Premium App
Yeah, you have download mode.
Now, fire up Odin and load a few rom files into it, connect the phone and see if the PC still recognises it. (Do not flash, Just a test)
If so...
Flash a stock rom.
Somehow, I was able to flash it with Odin in Download Mode this time. Phew! I read somewhere that the flash might fail if You're using wrong USB port. At first I connected my phone to a eSATA/USB combo port, and for the second time (after brick) I tried a normal USB 2.0 port in my laptop. Maybe that's what made the difference, I have no idea.
Anyway, I'm running stock Samsung 2.3 rom and am trying to install Darky's 10.0 RC3 on it - I am running into some problems, but thankfully they're much less serious than the brick that I was able to fix.
Thanks for Your help!
I ran into similar problems last week. A rom wouldn't flash, so I gave it an hour and it proceeded nowhere. Had to pull the plug on it.
Sometimes it just takes a few times plugging and unplugging repeatedly until it just happens to get detected by Windows. Maybe just a bit of luck too
Congrats on your recovery.
Just wondering which stock 2.3 rom did you use and which Odin setting you used to get your phone up and working again.
Here is my post / problem, seems similar to yours
http://forum.xda-developers.com/showthread.php?t=1020223
Thanks
I had the same issue like warnec on my first darkyy flash, finally everything went fine...don't worry!
just try to reflash with odin (maybe going for a stock version first is a good idea), be sure to do everything as mentioned in the guides out there. and be sure your computer works stable, maybe you want to quit some tasks in the background (however it should work even without but something crashed my odin once...)
Reflash with Odin to make your phone work again. I suggest using a stock 2.2.1/2.3.3 ROM. It is important that it consists of the 512.pit file, a PDA file, a Phone file and a CSC file. The ROM must have bootloaders included!
Now, disconnect your phone and turn it off.
Start Odin and load all the files. Tick 'Repartition'.
Start your phone in Download Mode by pressing Vol-Down, Home and Power.
Connect it to your PC and wait for Odin to say 'Added!'.
Now hit Start, wait 2-3 minutes until it is done and your phone should succesfully reboot!
Sent from my GT-I9000 using XDA Premium App
Thanks I tried this and my phone just keeps flashing i9000m screen, then blank and then back to the i9000m screen. Looks like the phone is unusable.
chriszak said:
Thanks I tried this and my phone just keeps flashing i9000m screen, then blank and then back to the i9000m screen. Looks like the phone is unusable.
Click to expand...
Click to collapse
does not sound very good...could you solve your problem yet?
Had to take the phone into Bell. Waiting on return of it and currently using a loaner HTC Desire Z from Bell.

Bricked my phone while flashing from Phoenix to stock 2.3.3

Hi everyone! I have Captivate(1008 batch) with Phoenix Ultimate firmware. Today I tried to flash it with batch Gingerbread. Seems like my mistake was that I forgot to turn off lagfix. Odin halted. Now I'm getting "phone-!-PC" screen each time I connect phone to PC...
I can not get cappy into download mobe(tried all 3 ways)
Odin doesn't see phone...
Do I have any chaces to repair my phone or it's a brick? Is there a chance that jig will help?
There's a new thread in the dev section about a one click unbrick from that screen. I read that it's just downlad the software, plug in phone and click run.
AdamOutler made this -
http://forum.xda-developers.com/showthread.php?t=1153310
Ok, thanks I'll try that! BTW which fimware should I flash if my cappy is back to download mode? As I understand Phoenix formated my phone memory into ext4 filesystem. Is that possible to flash stock Gingerbread on ext4 filesystem?
UPD: Unfortunately software unbrick doesn't help I got "Phone is not connected" message. My PC doesn't see phone at all
The Jig should work, assuming you don't have mixed bootloaders. If you do have mixed bootloaders, JTAG service will be what you need.
If you do manage to get back to download mode, use the JF6 Odin 1-click.
You can get it here: http://forum.xda-developers.com/showthread.php?t=731989
Here's another suggestion that I did with a 1008 that I had a while back. open Odin 1 click to prepare for download mode. (make sure it's not one with the three button fix - if you one click from gingerbread to 3 button fix stock, it is a certain hard brick).
Remove battery, count to 10, replace battery.
hold the vol up and vol down buttons at the same time until you see the screen flash. It should flash every 5-7 seconds as long as you continiuosly hold the buttons.
When you see the screen flash, insert usb cord (with it already connected to computer).
This got me to download mode. It mat take a few tries. sometimes it's a challenge to get to DL mode from this screen. This procedure worked on my 1008. Hope it works.
A jig may work too, but it n ever worked for me on the 1008.
Thank you guys. Hope your suggestions will help!
With the phone and PC screen the Jig will work for sure try and make one or u can buy it.
You can also try this, Remove the battery open odin 1 cick and plug the cable to the usb port at the back of the PC and then the phone and now put the battery see if the odin lits up if yes you are done.
I solved the problem(even without jig). So writing my solution, hope this will help someone.
1) I went home to use another PC. Installed Samsung drivers there.
2) I tried different key combos. Vol Up + Vol Down didn't worked but Vol Down + USB entered Download mode.
3) One guy from russian android forum told me to try with Odin 1 click 2.1 stock firmware. Only this version of firmware connected to my soft bricked phone.
One more time thanks everyone for your replies
For future reference.
If your phone turns on (you can see anything on the screen), then you do not have a perminate brick, and a jig will work.
And your filesystem/lagfix does not matter with odin 1click. It resets everything to the way it came, nomater what you came from. (It even works on cm7 witch repartisioned it and used MTD).
I have the same problem as you. I can't get get the one-click unbrick to work (doesn't detect a device). I ordered a jig yesterday, hopefully it comes soon. I have a 1010 though, which I heard had more problems than others.
use a JIG
i made my custom JIG for 60 cents, save my Cappy after a failed cyanogen install.

help bricked phone

Hi everyone. Im not normally in this section as i have an x8 but my friend has seen all the roms,mods and updates ive done so he tried to do it to his galaxy s i9000 without rooting or unlocking his bootloader. I asked him what he did he said he just tried to update software with keis but now it wont turn on just white screen with a red triangle in the middle i hope its download mode as i dont have a galaxy i dont really no but the battery has died and it wont charge im guessing hes damaged the bootloader am i right and if so whats the best corse of action to tepair it. Thanks.
You can check if it is in download mode by pluggin it in pc with odin. See the wiki page what it says about soft brick.
Soft-Bricked
After flashing a rom you might not be able to enter the Download Mode by pressing Volume Down + Home + Power. In this case a so called 'JIG' would be helpfull.
You could build it on your own: [HOWTO] [REF] Get Download Mode without 3-button combo using homemade JIG
... or buy a preassembled one on a well known marketplace.Hint: There is no difference between a JIG for Samsung S/S2 or S-Plus.
See if you can go into d0wnload mode with vol down home and power. If that works go and try to find the stock firmware for the phone and download and extract. Download odin and put csc pda and phone/modem in there rightful places. 512 pit in pit section. Pit usually comes with odin download. If not find it somewhere. Repartition checked and hit start. It should reboot when done. It will problaby take a couple of min to boot but be patient. If it starts to go into boot loop put back into download mode again and reflash. Its very hard to mess up the phone to where you cant fix it. So relax and watch tuts or whatever helps you best. I know of a link i that i will find and post for you when i do.
Sent from my GT-I9000 using XDA
http://forum.xda-developers.com/showthread.php?t=1102881
Sent from my GT-I9000 using XDA
DEAD bricked phone
So, my friend's phone (hopefully she'll stay my friend after this) was turning itself on and off all on it's own. So I (no good deed goes unpunished) suggested that I will upgrade her firmware for her. She had 2.3.3 firmware. I downloaded the odin1.7 as well as a package of all the info for 2.3.5 firmware upgrade. I flashed the phone- originally only using the PDA option with a file called: CODE_I9000XXJVS_CL565837_REV03_user_low_ship
It worked, the phone restarted and showed the firmware as being 2.3.5.
I don't know why, but I thought it would be a good idea to update the CSC and the pit and the modem as well- so I did that. when this was finished - though odin said that the flashing was successful the phone is completely unresponsive. The computer doesn't recognize it, it doesn't show any signs of life at all- like it's in the dark ages and there is no electricity in it.
HELP!!!
First question: do you think a jig will work? how dangerous is it?
second question: is there any other option to try that I haven't come across other than changing the motherboard, and if there isn't do you know where I can get one, bear in mind I live in Israel.
Please e-mail me a copy of the response to [email protected] if you can...
Odin dosnt pick it up atall plus the batteries dead aswell now and the stupid thing wont charge so i cant evan try any thing till i find away or some one to charge it but thanks for the tips.
gavster26 said:
Hi everyone. Im not normally in this section as i have an x8 but my friend has seen all the roms,mods and updates ive done so he tried to do it to his galaxy s i9000 without rooting or unlocking his bootloader. I asked him what he did he said he just tried to update software with keis but now it wont turn on just white screen with a red triangle in the middle i hope its download mode as i dont have a galaxy i dont really no but the battery has died and it wont charge im guessing hes damaged the bootloader am i right and if so whats the best corse of action to tepair it. Thanks.
Click to expand...
Click to collapse
Try to recharge the battery from other phone or use another battery.
Check whether you have the download mode working. (Home+Power+Volume down)
If yes, put phone in download mode and flash Darky RE or any other Rom via ODIN. Try to get the recovery mod after rooting and then try ROMs.
Or try restarting the phone it may work without update also. Long press power in download mode restarts the phone. However be careful.
What is the status of the device can you go to download mode
Post your firmware files name and how you choose in the odin flasher.
Dont try anything crazy you will bricked your device more:banghead:
Sent from my GT-P1000 using XDA
Alternate way to Download mode
Hi gavster26
I have been there with a buddy's phone... not a nice place.
Found a link showing this other trick ... but you have to trial and error this one on the different combos:
1. Phone off
2. USB cable pluged in
3. Odin running
4. Down (or Up - test both) Volume button + Home button + plug in the USB cable.
This booted my dead "bricked" phone into download mode.
Try it.

Categories

Resources