Hi everyone. Im not normally in this section as i have an x8 but my friend has seen all the roms,mods and updates ive done so he tried to do it to his galaxy s i9000 without rooting or unlocking his bootloader. I asked him what he did he said he just tried to update software with keis but now it wont turn on just white screen with a red triangle in the middle i hope its download mode as i dont have a galaxy i dont really no but the battery has died and it wont charge im guessing hes damaged the bootloader am i right and if so whats the best corse of action to tepair it. Thanks.
You can check if it is in download mode by pluggin it in pc with odin. See the wiki page what it says about soft brick.
Soft-Bricked
After flashing a rom you might not be able to enter the Download Mode by pressing Volume Down + Home + Power. In this case a so called 'JIG' would be helpfull.
You could build it on your own: [HOWTO] [REF] Get Download Mode without 3-button combo using homemade JIG
... or buy a preassembled one on a well known marketplace.Hint: There is no difference between a JIG for Samsung S/S2 or S-Plus.
See if you can go into d0wnload mode with vol down home and power. If that works go and try to find the stock firmware for the phone and download and extract. Download odin and put csc pda and phone/modem in there rightful places. 512 pit in pit section. Pit usually comes with odin download. If not find it somewhere. Repartition checked and hit start. It should reboot when done. It will problaby take a couple of min to boot but be patient. If it starts to go into boot loop put back into download mode again and reflash. Its very hard to mess up the phone to where you cant fix it. So relax and watch tuts or whatever helps you best. I know of a link i that i will find and post for you when i do.
Sent from my GT-I9000 using XDA
http://forum.xda-developers.com/showthread.php?t=1102881
Sent from my GT-I9000 using XDA
DEAD bricked phone
So, my friend's phone (hopefully she'll stay my friend after this) was turning itself on and off all on it's own. So I (no good deed goes unpunished) suggested that I will upgrade her firmware for her. She had 2.3.3 firmware. I downloaded the odin1.7 as well as a package of all the info for 2.3.5 firmware upgrade. I flashed the phone- originally only using the PDA option with a file called: CODE_I9000XXJVS_CL565837_REV03_user_low_ship
It worked, the phone restarted and showed the firmware as being 2.3.5.
I don't know why, but I thought it would be a good idea to update the CSC and the pit and the modem as well- so I did that. when this was finished - though odin said that the flashing was successful the phone is completely unresponsive. The computer doesn't recognize it, it doesn't show any signs of life at all- like it's in the dark ages and there is no electricity in it.
HELP!!!
First question: do you think a jig will work? how dangerous is it?
second question: is there any other option to try that I haven't come across other than changing the motherboard, and if there isn't do you know where I can get one, bear in mind I live in Israel.
Please e-mail me a copy of the response to [email protected] if you can...
Odin dosnt pick it up atall plus the batteries dead aswell now and the stupid thing wont charge so i cant evan try any thing till i find away or some one to charge it but thanks for the tips.
gavster26 said:
Hi everyone. Im not normally in this section as i have an x8 but my friend has seen all the roms,mods and updates ive done so he tried to do it to his galaxy s i9000 without rooting or unlocking his bootloader. I asked him what he did he said he just tried to update software with keis but now it wont turn on just white screen with a red triangle in the middle i hope its download mode as i dont have a galaxy i dont really no but the battery has died and it wont charge im guessing hes damaged the bootloader am i right and if so whats the best corse of action to tepair it. Thanks.
Click to expand...
Click to collapse
Try to recharge the battery from other phone or use another battery.
Check whether you have the download mode working. (Home+Power+Volume down)
If yes, put phone in download mode and flash Darky RE or any other Rom via ODIN. Try to get the recovery mod after rooting and then try ROMs.
Or try restarting the phone it may work without update also. Long press power in download mode restarts the phone. However be careful.
What is the status of the device can you go to download mode
Post your firmware files name and how you choose in the odin flasher.
Dont try anything crazy you will bricked your device more:banghead:
Sent from my GT-P1000 using XDA
Alternate way to Download mode
Hi gavster26
I have been there with a buddy's phone... not a nice place.
Found a link showing this other trick ... but you have to trial and error this one on the different combos:
1. Phone off
2. USB cable pluged in
3. Odin running
4. Down (or Up - test both) Volume button + Home button + plug in the USB cable.
This booted my dead "bricked" phone into download mode.
Try it.
Related
I'm really sorry, I searched for solutions but didnt found one that fits my problem.
I'm a total newbie and ****ed up my phone in many ways. I started trying to install something it wasnt suposed to work on my phone (rom destinated to 9000 and stuff). I have a Samsung Galaxy S GT-I9000b (sold to latin amarica) and came from factory with android 2.2.
I'm now stuck with the black screen of death, no matter what I do I get this screen. It hapened after I tryied to install unsucessfully the original rom of the phone and odin presented me with an error.
Before I try any further I'd like your advices as how to procede regarding my 9000b. Pulling the battery out, putting it in again and holding either vol down or both volumes and either pluging the phone on usb or pressing power allways gives me the same result, the screen with phone exclamation triangle and pc.
So, before I buy a jig cable on ebay that will probably take 3 weeks to get here (Brasil) is there anything else I can try?
Please help me, I'm desperate and I dont want to take it to assistence, it would cost me much money and ruin all my courage in trying to use Roms.
Thanks alot and sorry for the bad english.
so did you have the 3 button combination before this happened ??
have you tried to charge the phone whilst powered off, then when the phone gets hot, try download mode then ? sometimes this works, as heat can help download mode work.
another thing that has worked for SOME people, is leaving the battery out for 10mins, doing the 3 button combo, and whilst holding the 3 buttons, insert the battery.
you could try these and see what happens,
And 3 weeks delivery for the JIG is a long time, couldnt you make one in less that 3 weeks.
If you can't get into download mode, you are screwed until you get your hands on a jig, simple as that. Just wait. Patience is a virtue.
Thanks in advance for the quick reply guys, I ordered the jig, estimated 20 days, usualy it takes the same amount from the central postal ofice to my home since they allways restrict packages from hong kong. I'm considering making one but I'm a total denial in eletronics.
I was able to get to download mode before this problem yes. I would just hold down vol and center key and then power. Now even when I plug it in to charge I get the screen with the exclamation.
Any more sugestions?
no other suggestions other than whats listed above
looks like you will have to wait for the JIG to arrive.
Loner-phone here you come lol
Then I have a couple of questions.
1) Since I plut it in directly on the power and still recive the same screen is the phone still charging? Or once the battery is over I'm ****ed up twice?
2) Is there any chance that the jig wont work or I in some way ****ed up my I-9000b permanently?
3) After I make/get a jig how should I procede? I heard about one-click odin, but apears that its for another model of phone, and since I got on all this trouble exactly for trying to do things to my phone that were suposed to be only for another model, I'm kind of lost.
Inputs?
Thank you all for already awnsering my questions.
1) the system is corrupted so the charging indicator will be too - thus leading to Phone ! PC image - this is the only image the phone can now produce
2) The 'JIG' has a 100% success rate - providing that the motherboard is not fried - which it isnt as it still shows an image
3) the jig is just a modified USB, just plug it into the phone whilst powered off and download mode will appear, and then you just attach your genuine USB cable and flash stock ROM thru ODIN.
azzledazzle Thank you very much for your patience, but since I`m a total newbie to all this, some of your awnsers I didnt understood fully, do you care explain me better?
Regarding question 1) The power indicator is corrupted, ok. But this means if my battery die out of usage it wont charge again or just that the indicator wont show that is charging but the battery actualy is charging?
and for question 3) Is ther any tutorial directed to I-9000 on how to use odin to flash a stock ROM ? like baby steps? After all that I'm even afraid to turn the phone on, so I would like to know exactly what to do. I`m cosindering asking someone with technical skills to help me on a home made jig.
oh im sorry, i get carried away sometimes.
1) i assume the battery will be charging yes. only the phone will not be able to show this due to the corruption.
2) when you have made / bought a JIG (link below) you ideally want to flash a Stock ROM, you can get this from samfirmware (link below) and also on this site is a tutorial on how to use ODIN, its fairly easy if you just read the instructions provided.
JIG: http://forum.xda-developers.com/showthread.php?t=819551&page=3
Firmwares : www.samfirmware.com
ODIN download and guide : http://forum.xda-developers.com/showthread.php?t=846913
Its a miracle, somehow I managed to get into download mode. But I'm still a bit insecure
Here is the deal, I dowloaded a .tar file that alledgedly from my carrier and for my country. The tar is named JPA_JP3_JPA.
Inside the file there are cache.rfs factoryfs.rfs modem.bin param.lfs zimage
But what should I put where on ODIN if I only have PIT PDA PHONE and CSC?
And how can I discover if I should use pit 512 or 803?
Should I consider a master clear setting?
the file you downloaded is a full firmware compressed into 1 .tar file.
so in odin load the .tar file into PDA section and THATS IT !!
DO NOT USE PIT WITH THIS FILE.
press start and enjoy
PS do a factory reset after the flash
vongikking said:
I'm now stuck with the black screen of death, no matter what I do I get this screen. It hapened after I tryied to install unsucessfully the original rom of the phone and odin presented me with an error.
Click to expand...
Click to collapse
Hello all!
I've got my hands on a GT-I9000 today.
It's got 2.3.3 Android on it.
Wanting to install CM7, I was first of all trying to root it.
I'm on Mac OS X 10.6.8, thus I downloaded heimdall-frontend and the "Hardcore's SpeedMod kernel with ClockworkMod Recovery".
When I put my phone into DL Mode and connect it to my Mac, I can't write the image to it.
Heimdall is failing with "Failed to receive device info response!"
What do you ppl suggest me to do now?
Thanks,
F.
Try to flash with Windows!
Sent from hell to take your soul
Lunchbox115 said:
Try to flash with Windows!
Sent from hell to take your soul
Click to expand...
Click to collapse
Indeed I now managed to get Windows XP PC.
one trouble still remains: after rooting the device remains in an infinite reboot loop!!!
It only stops when WiFi is disabled.
Any help bout this?
Or at least any means to get back to a factory ROM?
I got 2.3.3 before flashing...
Thanks!
Try to flash the nightly again, should solve the bootloop-issue.
Or you can wipe cache/dalvik cache, this helped me too.
Lunchbox115 said:
Try to flash the nightly again, should solve the bootloop-issue.
Click to expand...
Click to collapse
Which nightly do you intend me to re-flash?
Or you can wipe cache/dalvik cache, this helped me too.
Click to expand...
Click to collapse
How do I achieve these two things?
Thanks,
F.
Just take the latest nightly. To wipe the cache/dalvik cache you have to boot into recovery (hold volume UP + home button + power button.
Sent from hell to take your soul
Hi everyone! I have Captivate(1008 batch) with Phoenix Ultimate firmware. Today I tried to flash it with batch Gingerbread. Seems like my mistake was that I forgot to turn off lagfix. Odin halted. Now I'm getting "phone-!-PC" screen each time I connect phone to PC...
I can not get cappy into download mobe(tried all 3 ways)
Odin doesn't see phone...
Do I have any chaces to repair my phone or it's a brick? Is there a chance that jig will help?
There's a new thread in the dev section about a one click unbrick from that screen. I read that it's just downlad the software, plug in phone and click run.
AdamOutler made this -
http://forum.xda-developers.com/showthread.php?t=1153310
Ok, thanks I'll try that! BTW which fimware should I flash if my cappy is back to download mode? As I understand Phoenix formated my phone memory into ext4 filesystem. Is that possible to flash stock Gingerbread on ext4 filesystem?
UPD: Unfortunately software unbrick doesn't help I got "Phone is not connected" message. My PC doesn't see phone at all
The Jig should work, assuming you don't have mixed bootloaders. If you do have mixed bootloaders, JTAG service will be what you need.
If you do manage to get back to download mode, use the JF6 Odin 1-click.
You can get it here: http://forum.xda-developers.com/showthread.php?t=731989
Here's another suggestion that I did with a 1008 that I had a while back. open Odin 1 click to prepare for download mode. (make sure it's not one with the three button fix - if you one click from gingerbread to 3 button fix stock, it is a certain hard brick).
Remove battery, count to 10, replace battery.
hold the vol up and vol down buttons at the same time until you see the screen flash. It should flash every 5-7 seconds as long as you continiuosly hold the buttons.
When you see the screen flash, insert usb cord (with it already connected to computer).
This got me to download mode. It mat take a few tries. sometimes it's a challenge to get to DL mode from this screen. This procedure worked on my 1008. Hope it works.
A jig may work too, but it n ever worked for me on the 1008.
Thank you guys. Hope your suggestions will help!
With the phone and PC screen the Jig will work for sure try and make one or u can buy it.
You can also try this, Remove the battery open odin 1 cick and plug the cable to the usb port at the back of the PC and then the phone and now put the battery see if the odin lits up if yes you are done.
I solved the problem(even without jig). So writing my solution, hope this will help someone.
1) I went home to use another PC. Installed Samsung drivers there.
2) I tried different key combos. Vol Up + Vol Down didn't worked but Vol Down + USB entered Download mode.
3) One guy from russian android forum told me to try with Odin 1 click 2.1 stock firmware. Only this version of firmware connected to my soft bricked phone.
One more time thanks everyone for your replies
For future reference.
If your phone turns on (you can see anything on the screen), then you do not have a perminate brick, and a jig will work.
And your filesystem/lagfix does not matter with odin 1click. It resets everything to the way it came, nomater what you came from. (It even works on cm7 witch repartisioned it and used MTD).
I have the same problem as you. I can't get get the one-click unbrick to work (doesn't detect a device). I ordered a jig yesterday, hopefully it comes soon. I have a 1010 though, which I heard had more problems than others.
use a JIG
i made my custom JIG for 60 cents, save my Cappy after a failed cyanogen install.
Hello,
I tried to flash back to the stock ROM of Galaxy S and then install a new Jetpack 8.2 custom ROM.
Apparently, since I did a bad search on the internet on finding a stock ROM and pit file, i downloaded a pack from xda with the .pit file pda file phone file and CSC file.
I DONT REMEMBER which it was..i selected all the files from the pack through odin and re-partitioning was ticked (i saw it after the flash finished).
So when the processes was completed waited a bit and since the phone was not responding i pulled it out.
Now that's it.. The screen is black - wont power on - wont go into download mode - wont show battery charge while the USB cable is on - nothing (AND YES THE BATTERY IF FULLY CHARGED).
Is there anything i can do to fix it?
p.s: havent tried a usb jig but from searches i made on the internet and on xda forums ppl said it will prolly not work. are there any instruction on how to make one (link would be appriciated)?
Thanks in advance
Best option would be to try a Jig (you can buy one on ebay or dealextreme) and see if you can go into DL mode. Sometime the button combination for Download mode changes depending on the firmware. Try pressing the middle of the volume rocker and power at the same time.
If not wait for a Jib or build yourself one. There should be instruction in this forum on how to build one.
if the jig doesn't work, i would try and return it to the store you got it. I know its a long shot, but the same thing happened to me and I brought it back and she just gave me a new phone! Its worth a shot!
evanogrady said:
if the jig doesn't work, i would try and return it to the store you got it. I know its a long shot, but the same thing happened to me and I brought it back and she just gave me a new phone! Its worth a shot!
Click to expand...
Click to collapse
Worth a try. Just tell them it suddenly stopped working and you have no idea what's wrong. It's not like they can power it on and see that you failed flashing it or something. and even if they use a jig they can only get to download mode and reflash it...
even if they say no... a jig costs like $1.5 on eBay. search for "i9000 jig".
Insert if, press the power button and poof, you're in download mode,
the thing is that the phone is not under any warranty or something and the store i got it is far away now !!
JTAG service if you're in the UK: http://www.fonefunshop.co.uk/
The JIG won't work when you brick with a black screen (i.e. bootloader corruption, so no boot at all).
Your only solution is to JTAG it or sadlly, throw it away...
I used a I9003 ROM to flash it !!
Maybe there is still a solution?
also from what i've found on forum sometimes the JIG helped ppl who had a black screen to go into download mode. so how can you be so sure? @ Dan_Aykroyd
immortalcy said:
I used a I9003 ROM to flash it !!
Maybe there is still a solution?
also from what i've found on forum sometimes the JIG helped ppl who had a black screen to go into download mode. so how can you be so sure? @ Dan_Aykroyd
Click to expand...
Click to collapse
As long as your bootloader is intact, the jig will get you to the download mode
Wrongly flashed i9000 with i897 rom has been confirmed to work with the jig, but i don't know i9000 with i9003 rom...
Or you can apply the unbrickable mod if your phone's warranty was voided already, if not, send it back to the shop.
immortalcy said:
Hello,
Now that's it.. The screen is black - wont power on - wont go into download mode - wont show battery charge while the USB cable is on - nothing (AND YES THE BATTERY IF FULLY CHARGED).
Click to expand...
Click to collapse
Had that also yesterday putting a new ROM on my GS. The process of writing the PDA halted.. Black screen, no way to start it up en no screen indications of charging etc..
I removed it from my USB, Removed the battery a few times did the three way download mode trick several times and finally I got the download mode screen from where I successfully loaded the new ROM.
So try a few times.. even when you get a black screen !!
let me be clear once more..i downloaded a complete I9003 rom pack from xda... some guy posted..i just missed that it was I9003 and not I9000..
and on odin re-partition was clicked..but the process was completed successfully even thou after that the phone wont start or go into download mode :/
i used not only PDA and PIT files but 2 more was included as well :/ so what i am asking is if this could really have damaged the bootloader or not
immortalcy said:
I used a I9003 ROM to flash it !!
Maybe there is still a solution?
also from what i've found on forum sometimes the JIG helped ppl who had a black screen to go into download mode. so how can you be so sure? @ Dan_Aykroyd
Click to expand...
Click to collapse
Of course you're bound to brick it flashing a firmware for a phone completely different to yours...get a jig if you're confident or take it to a service centre
Sent from my GT-I9100 using xda premium
dk206 said:
Of course you're bound to brick it flashing a firmware for a phone completely different to yours...get a jig if you're confident or take it to a service centre
Sent from my GT-I9100 using xda premium
Click to expand...
Click to collapse
Try jig first.
Next try JTAG or UNBRICKABLE mod.
Then Try a service centre.
in case it wokes up.. anyone has links for stock rom and pit to flash with odin?
thanks again
There are some ways, when already got into DL mode is best to reflash with 812.pit file and then again with 512.pit file. After I bricked my phone and got "death" screen (God I was crying) I found way of taking up DL mode (hopefully SGS is pretty-hard to brick). Others than that try to connect to your phone via usb (remember to first inset usb and then battery) and hold ALL of the buttons on your phone. Screen must flash about 3 times and then release volUp to get DL mode combo. I hope that will help you as me.
Taxiozaurus said:
There are some ways, when already got into DL mode is best to reflash with 812.pit file and then again with 512.pit file. After I bricked my phone and got "death" screen (God I was crying) I found way of taking up DL mode (hopefully SGS is pretty-hard to brick). Others than that try to connect to your phone via usb (remember to first inset usb and then battery) and hold ALL of the buttons on your phone. Screen must flash about 3 times and then release volUp to get DL mode combo. I hope that will help you as me.
Click to expand...
Click to collapse
Any updates on this ? cause I'm also having the same issue!
Dan_Aykroyd said:
The JIG won't work when you brick with a black screen (i.e. bootloader corruption, so no boot at all).
Your only solution is to JTAG it or sadlly, throw it away...
Click to expand...
Click to collapse
Are you 100% sure the JIG wont work if bricked with a black screen. Are there any other possibilities to unbrick the phone. I really need this phone back or my dad will kill me..
soooooooo. I have a i9000m and i wanted to flash it using odin because cwm wasn't working and i googled for vibrant. so i didn't really pay attention to the title when it said ``captivate only`` http://forum.xda-developers.com/showthread.php?t=731989 it went through the odin process but phone didn't restart. it just turned off and stayed off so I unplugged and now, it just shows the at&t world phone white background screen. and keeps restarting. cant get to recovery or download mode. odin doesn't see it either. I read many forums and I think Im going to have to go with the usb jig but before I do Im just wondering if there's another method to get into download mode or some program or adb that can find the phone. thanks
pankajs37 said:
but before I do Im just wondering if there's another method to get into download mode or some program or adb that can find the phone. thanks
Click to expand...
Click to collapse
If you click the link below ( My Android Collections), you can try Easy Reboot Recovery..using ADB or the Android Recovery Tools, they have options for various functions, preset by developers
yeah....using adb is the only possibility i would take into consideration too
xsenman said:
If you click the link below ( My Android Collections), you can try Easy Reboot Recovery..using ADB or the Android Recovery Tools, they have options for various functions, preset by developers
Click to expand...
Click to collapse
thanks
pankajs37 said:
soooooooo. I have a i9000m and i wanted to flash it using odin because cwm wasn't working and i googled for vibrant. so i didn't really pay attention to the title when it said ``captivate only`` http://forum.xda-developers.com/showthread.php?t=731989 it went through the odin process but phone didn't restart. it just turned off and stayed off so I unplugged and now, it just shows the at&t world phone white background screen. and keeps restarting. cant get to recovery or download mode. odin doesn't see it either. I read many forums and I think Im going to have to go with the usb jig but before I do Im just wondering if there's another method to get into download mode or some program or adb that can find the phone. thanks
Click to expand...
Click to collapse
I accidentally Flashed a vibrant rom on my i9000. When I finally did get it into download mode with the JIG, I flashed back to stock firmware with ODIN and It totally ruined my phone.... The screen went all crazy and it kept rebooting faster than odin could do anything to it.
Just be careful. Im really not sure what happened But its pooched now for sure. JTAG is my only option on that one
if u dont own JIG or u dont know how to use ADB . the other way is
remove battery from phone /sim card / sd card
take the USB connect with ur Laptop or PC ( dont use it with charger it will not work)
connect with ur phone , then u will see the black screen being lil bit lighter
pres the 3 combos button to enter download mode and then flash ur ROM
this always worked for me , i hard bricked 4 times already my phone :/
Hi,
I have a big problem. I made a stupid mistake and flashed an original Gingerbread firmware directly over Froyo.
Now my Phone isn't able to start, the only thing tha happens is, that the backround light turns on. I am not able to reach the download mode and my pc can't detect the phone.
Could anyone help me?
Maizelll
Today i bought a USB-JIG, but I can't reach the bootloader with it.
you cannot reach bootloader mode with jig and try going into download mode by pressing power+home+volume down button
and gingerbread firmware is always flashed over froyo
i think you have used the firmware which is without bootloader and thats why you are getting black screen
just try to flash a four package firmware
But my pc doesn't detect the phone and i can't reach the download mode with the three buttons, i always get a black screen
try to search for samsung usb drivers and install them. after, recover by odin.
try to put off the battery , sim card and microSD , wait for 1-2 minutes
after that , put back battery only
try to enter download mode
*sorry for my bad english*
Maizelll said:
Hi,
I have a big problem. I made a stupid mistake and flashed an original Gingerbread firmware directly over Froyo.
Now my Phone isn't able to start, the only thing tha happens is, that the backround light turns on. I am not able to reach the download mode and my pc can't detect the phone.
Could anyone help me?
Maizelll
Click to expand...
Click to collapse
Ok... first download full firmware from sammobile or in yagyagaire's blog. Next you need to remove sim, sd card and battery from your phone. Now hold the three buttons which let you go in download mode. While holding those buttons insert the battery and you will most probably be in download mode. Then flash the downloaded firmware via Odin and then :victory:
Sent from Galaxy mini running CM10(Android 4.1.2 (Jellybean)).
guys why discussing on a 1 month old thread
Guessing they just want some closure.