[Q] plz help! - Touch Diamond2, Pure Q&A, Help & Troubleshooting

hi,
after i setup GoogyROM_v3.4 WM6.1 my phone just reset and reset and doesn't boot . hard reset doesn't work and i can not install other roms .

digitaldesign said:
hi,
after i setup GoogyROM_v3.4 WM6.1 my phone just reset and reset and doesn't boot . hard reset doesn't work and i can not install other roms .
Click to expand...
Click to collapse
Set your TD2 into the bootloader-mode:
- Take the battery out
- Wait a few seconds and reseat it
- hold the volume-down button and while holding switch the phone on
Now you will be in bootloadermode (tricolor), so you can conntect it to your pc via usb and flash again (I suggest a stockrom)

Thanks so much.my problem was holding down and up volume together and doing hard reset instead of loading boot loader.

help me now
hello dears
please help me :
how to remove "solitaire" and "bubble breaker" in pocket pc ?
tanks for ur help

mohamamdsina0611 said:
hello dears
please help me :
how to remove "solitaire" and "bubble breaker" in pocket pc ?
tanks for ur help
Click to expand...
Click to collapse
1. new question (vour post is not related to the topic of this thread) = start a new thread
2. have you seached this forum?

mohamamdsina0611 said:
hello dears
please help me :
how to remove "solitaire" and "bubble breaker" in pocket pc ?
tanks for ur help
Click to expand...
Click to collapse
I am sorry to tell you that you can't remove any applications which are integrated in a ROM.

Related

XDA IIS DEAD WHILE UPGRADE

I was trying to upgrade the rom , it was at the third part (upgrading CE) then computer locked... now all i see vertical lines at my XDA IIS can someone help me please ?
No power , no reset , computer cannot connect to the XDA please help me
oh, thankyou very much, I tried many times with many ways but still failed.
Thanks all.
Great
[CHECKCEID_TYPE]=1
RELOAD said:
No power , no reset , computer cannot connect to the XDA please help me
Click to expand...
Click to collapse
Don't worry man, Now you need to enter boot loader
Press power + camera + soft reset
Now you can connect to your PC and Upgrade again
Thanks i did it and works , sorry for edit my first message ,

Xda ii not start after upgrade wm6.1

Plz help me n sorry 4 my bad english b,coz i m new hear.i have a xda ii pda n i upgrade it wm2003 to wm6.1 but i dont do d hard reset n now my pda is on o2 screen n i dont do anything if press reset button+camera+record button for hard reset it no screen show if i plug in for charge no light show n if i try to connect to pc d pc says usb erorr n no light show now what can i do? Plz help me
dhellb0y said:
Plz help me n sorry 4 my bad english b,coz i m new hear.i have a xda ii pda n i upgrade it wm2003 to wm6.1 but i dont do d hard reset n now my pda is on o2 screen n i dont do anything if press reset button+camera+record button for hard reset it no screen show if i plug in for charge no light show n if i try to connect to pc d pc says usb erorr n no light show now what can i do? Plz help me
Click to expand...
Click to collapse
when you pressed reset button+camera+record button, did you see the screen that has:
Enable KITL -> NO
Clean Registry Hive -> YES
Format Storage -> YES
if you couldn't see this option, try reflashing the rom..
gtrix said:
when you pressed reset button+camera+record button, did you see the screen that has:
Enable KITL -> NO
Clean Registry Hive -> YES
Format Storage -> YES
if you couldn't see this option, try reflashing the rom..
Click to expand...
Click to collapse
Thank you for replay.you say reflashing rom why i can do it? My pda is not connect to my pc.plz help me now what can i do?
Between hope and hate
dhellb0y said:
Thank you for replay.you say reflashing rom why i can do it? My pda is not connect to my pc.plz help me now what can i do?
Click to expand...
Click to collapse
It is absolutely necessary that your device does enter bootloader mode.
Press On/Off button, DPad and Soft Reset all together!!
Your device should show 'Serial' now! Connect to your PC and the device should change to: 'USB'.
Otherwise you got a nice paperweight now, and that would be bad.
Did you follow this, as you flashed the first time?
http://forum.xda-developers.com/showthread.php?t=332215
Did you use XP od vista 32bit (64bit does not work!?!) and did you follow this guide?
http://forum.xda-developers.com/showthread.php?t=428469
Never disconnect the device or the power-charger while flashing.
Try to reflash to get your sweet back, for us it is the most important to find out what went wrong to prevent others to do the same mistake.
Good luck!

[Q] An huge problem!!

Sorry, but I have a big big problem. I have an x1, and I flashed the previous version of Energy Rom on the sd card. BUT I wanted to re-flash these, and the phone blocked in initial screen..the update rom one..
So, every time I try to update, it starts and after a few second, and when it start to update, the screen turns off. Finally, anyone can help me? I don't know how I can fix this situation PLEASE, HELP ME!!
Thanks, Fabio
Remove your Micro SD-CARD, and enter in flash mode! Volume down + power on!
Open the Update Phone Utility with the rom of your choice! Remember to rename your rom to: KOVSIMG.nbh
Sorry for English.
Faffa_mcr said:
Sorry, but I have a big big problem. I have an x1, and I flashed the previous version of Energy Rom on the sd card. BUT I wanted to re-flash these, and the phone blocked in initial screen..the update rom one..
So, every time I try to update, it starts and after a few second, and when it start to update, the screen turns off. Finally, anyone can help me? I don't know how I can fix this situation PLEASE, HELP ME!!
Thanks, Fabio
Click to expand...
Click to collapse
first time u must delete first the previous version on ur sd card... than u can update the new one... and dont forget to tasks 29 before u flash the rom...
Sorry guys, but when I enter in flash mode, and I press the power button and it should load the ROM, instead it always restart after 2-3 second. I don't know what to do..please help me!!
It sounds to me that you're not holding the buttons down correctly
paul c said:
It sounds to me that you're not holding the buttons down correctly
Click to expand...
Click to collapse
I tried again, but the result is the same.. uff..
hardspl
Faffa_mcr said:
I tried again, but the result is the same.. uff..
Click to expand...
Click to collapse
1. Try to pull up the batery for 10 menute.. and replace it again.. and press volume down and the power button together and dont realese until the boot screen appear...
2. connect ur x1 with the computer and hardspl the phone with the new spl 0.78.. when its finish the phone will restart.. pull the batery again for 1 menute.. and replace again... go to bootloader screen again like i explain in point 1.. after that conect again ur x1 with computer... do task29.. when finish its will restart again...
after u do task29.. u can flash ur x1 with the computer or with storage card..
this was the link for SPL 0.78 and task29 and if u still confused... http://www.826x.blogspot.com/
i think you can't flash the energy rom and always fail.. because u not hardspl your x1..
ahmadin said:
1. Try to pull up the batery for 10 menute.. and replace it again.. and press volume down and the power button together and dont realese until the boot screen appear...
2. connect ur x1 with the computer and hardspl the phone with the new spl 0.78.. when its finish the phone will restart.. pull the batery again for 1 menute.. and replace again... go to bootloader screen again like i explain in point 1.. after that conect again ur x1 with computer... do task29.. when finish its will restart again...
after u do task29.. u can flash ur x1 with the computer or with storage card..
this was the link for SPL 0.78 and task29 and if u still confused... http://www.826x.blogspot.com/
i think you can't flash the energy rom and always fail.. because u not hardspl your x1..
Click to expand...
Click to collapse
Sorry, I tried to connect the x1 to pc..but the pc doesn't recognize the phone..
I looked that the power button have a red light, and when this turn off, it go to bootloader mode, but after few second (it's in update mode) the phone turn off..
Someone has the same problem? I don't know what to do, I'm desperate! I can't use my phone
first remove sd card.
then pull out battery, press power button without battery on phone for about 30 sec.
then place battery. try to hard reset without OS:
press and hold both softkeys of X1, and press power button to turn on phone. but don't release softkeys until appears blue text with white background. slide put keyboard press R, wait to complete then press SPACE.
phone will be hard resetted. if not helped to boot OS, or there's no OS, or you did task29 before then do another task29 after this prosedure.
hope it helps
Faffa_mcr said:
Sorry, I tried to connect the x1 to pc..but the pc doesn't recognize the phone..
Click to expand...
Click to collapse
did you try another usb port of PC?
orkhanahmadov said:
did you try another usb port of PC?
Click to expand...
Click to collapse
mmm no...but I think that's another problem, coz when I put the phone on ac mode, it's the same situation...
orkhanahmadov said:
first remove sd card.
then pull out battery, press power button without battery on phone for about 30 sec.
then place battery. try to hard reset without OS:
press and hold both softkeys of X1, and press power button to turn on phone. but don't release softkeys until appears blue text with white background. slide put keyboard press R, wait to complete then press SPACE.
phone will be hard resetted. if not helped to boot OS, or there's no OS, or you did task29 before then do another task29 after this prosedure.
hope it helps
Click to expand...
Click to collapse
orkhanahmadov said:
did you try another usb port of PC?
Click to expand...
Click to collapse
Very good explaination....
Faffa_mcr said:
mmm no...but I think that's another problem, coz when I put the phone on ac mode, it's the same situation...
Click to expand...
Click to collapse
did you try method that wrote first.
and off course try another usb port, or another usb cable.
because if the phone did'nt recognized by PC, it means there's problem with cable or usb port if other things are OK.

I can't turn on phone and enter to donload tool / recorvery mode HELP !!!

I HAVE A VERY BIG PROBLEM !!! Please Help
I got I9000T , and i can't turn on this phone and can;t enter to download tool/recorvery mode
What i must doing please help @
Hey
What happens if u try to power up??does it show a phone+!+computer??
tchindalia said:
Hey
What happens if u try to power up??does it show a phone+!+computer??
Click to expand...
Click to collapse
Nothing happens only shows the logo for 3 seconds.
Moodest said:
Nothing happens only shows the logo for 3 seconds.
Click to expand...
Click to collapse
1) Try charging your Battery to full first,
2) Try cleaning the contacts of your Battery and than try shifting your battery towards the contacts ( some people use a piece of folded paper to make their battery connections better)
3) Use solutions from My Android Solutions for download or recovery modes

Need Help Please....

Hello Friends,
While I'm trying to change the ROM for my phone via Odin, my phone is stopped and now 3-buttons function don't work, I tried many hard rest but no response,
what is your advice?
Thanks in advance
Hello Guys,
Please any help,
I tried
1. Volume UP + Menu + Power = doesn't work
2. Volume down + Power = doesn't work.
The phone is dead...
Any Help>>>
have a look here http://forum.xda-developers.com/showthread.php?p=30415128, if you have totally hard bricked it this maybe one of your only options http://forum.xda-developers.com/showthread.php?p=19003060#post19003060
You need a usb jig.
What is USB jig?
alisaher2000 said:
What is USB jig?
Click to expand...
Click to collapse
Ok I know now what is USB jig.
thanks I will do it.
alisaher2000 said:
Hello Friends,
While I'm trying to change the ROM for my phone via Odin, my phone is stopped and now 3-buttons function don't work, I tried many hard rest but no response,
what is your advice?
Thanks in advance
Click to expand...
Click to collapse
Save your bricked GT-i9000

Categories

Resources