Related
Ok so I'm running Darky's 7.5 ROM just loaded it and it's flying . i'm having issues connecting to my carrier. I"m from canada and run on a network owned by Sasktel. We get our phones from Bell and our current release is JL2 I think. I was running this ROM fine but wanted to see what all the hype was about .
Now the only problem i'm having is I can't register on my network and thus my phone isn't working as a phone, lol. can someone help me set it up. here are the frequencies we run on.
SaskTel
GSM - N/A
UMTS/HSPA - 850/1900
I went into the APN and set that up so I should have data I just need to get registered. I can see the network Sasktel but it wont let me register. I get the exact message when clicking on it
"Registering on Sasktel......You SIM card does not allow a connection on this network"
any help would be great, thanks
I tried going in here *#2263# but didn't know what to pick so I left it to automatic
I don't know.
When you flash back to official firmware, everything works fine again ?
This may sound funny but try 'sim unlock' your phone.
after flashing, your phone might have reverted back it's original lock which is to BELL.
I agree with the other reply stating for you to have your phone unlocked.
xxgg said:
I don't know.
When you flash back to official firmware, everything works fine again ?
This may sound funny but try 'sim unlock' your phone.
Click to expand...
Click to collapse
I unlocked my phone a while back and it's unlocked still, Network lock = off. and yes flashing to other roms specifically for my phone will work fine on the network. Is this because Darky's ROM is based on a European ROM JPY and i'm supposed to be running a Canadian ROM JL2?
Hi. I have a SGS straight from Sasktel here in SK. I checked my setting under 2263, and it is automatic (top one). After I checked it, it lost cellular connection for about a minute, then eventually came back (phew!).
adamge said:
Hi. I have a SGS straight from Sasktel here in SK. I checked my setting under 2263, and it is automatic (top one). After I checked it, it lost cellular connection for about a minute, then eventually came back (phew!).
Click to expand...
Click to collapse
awesome what happens when you go back into 2263 and click on the wcdma band, which ones are stared in there?I have 2100, 1900 and 900 starred but 850 is not.....Also could you post your APN settings. those are in settings, wireless network, mobile networks, access point names and then click on the inet.stm.sk.ca one and if it's not too much for you could you post them up here along with the wcdma band settings. Thanks bud
can we actually install darkys rom on BELL vibranat i9000M
i would like to find out if darkys Rom works with Bell vibrant thats i9000M from canada ?
well his rom is up and running fine yes, I just have to get the right setting to run on my carrier....I own a i9000m it's a bell phone that my carrier gets supply from. So yes his rom works great on this phone, it's so fast, I might try flashing a modem for the canadian phones and see if that works i'll post back
SOLVED - Sasktel (Bell) running Darky's ROM
So I figured it out, I was running JL2 and then flashed speedmod kernel to get 2e. I then upgraded to Darky's 7.5 ROM, when that came up I was unable to get on the network. I was getting an error "Sim doesn't allow connection on the network" error when looking in providers. anyways, I just flashed the JK3 modem and i'm back on the network with Darky's rom
I grabbed the modem from here.
http://forum.xda-developers.com/showthread.php?t=846237
I used JK3 because they were having issues with JK4 bricking for some reason and didn't want to risk it. now to just get JL2 modem some how
There is a JL2 modem floating around somewhere.
I am also running jk3 modem with xxJPY, love my phone now.
No more bridling issues
BlackDino said:
There is a JL2 modem floating around somewhere.
I am also running jk3 modem with xxJPY, love my phone now.
No more bridling issues
Click to expand...
Click to collapse
Me too, so fast and smooth
If we could get jl2 modem with darkys
Is there a way to get jl2. Modem working with darkys then it would be perfect if u do find it let us know and make a step by step tutorial how it's done from the scratch for newbees canadiens thanks
notoriouspk said:
Is there a way to get jl2. Modem working with darkys then it would be perfect if u do find it let us know and make a step by step tutorial how it's done from the scratch for newbees canadiens thanks
Click to expand...
Click to collapse
It's very simple, TURN OFF ANY/ALL lag fixes!!!!! Back your **** up. then you can begin
You phone should be unlocked but might not have to be.....mine was, you can grab sgs unlocker form the app market also, You have to be running 2e recovery. so check on that first by powering your phone off, wait till it's actually off, froyo vibrates when it's shut down. After it's off, hold volume up, home button and power till you see the i9000m then let it go. it should boot into recovery. If you were running Froyo then you will have a 3e recovery, we need 2e. Also you should check and make sure you can get into download mode, by powering off, volume down, home and power key. If you can't get inot download mode you have to fix that first. if you can proceed:
So grab the recent stable speedmod kernel from hardcore here DON'T get the development version:
http://forum.xda-developers.com/showthread.php?t=822756&highlight=speedmod
depending on how you want to flash grab either the CWM or the other one which needs to be flashed via odin. Flash either or and your phone should boot with 2e. follow the instructions hardcore has posted and make sure you hit the thanks button for him .
After we have 2e installed you can grab Darky's ROM located here:
http://forum.xda-developers.com/showthread.php?t=814091
I used the non wipe one and didn't have issues, make sure you back your **** up before flashing anything. If you notice battery drain after you flash you could flash the wipe version just to make sure. anyways, Follow Darky's instructions to the T and dont forget to thank him
After his ROM boots, I grabbed a modem for our phones (bell, sasktel) I used JK3 because the search wasn't working last night but found this morning a link to JL2....i'm not sure if this is legit JL2 because I haven't used it but give it a shot if it doesn't work flash another on top (I can confirm JK3 works)
JL2: http://forum.xda-developers.com/atta...1&d=1293577837
Grabbed that from a link Samdroid_G_S posted so thank him for that.
JK3: was from docs link located here:
http://forum.xda-developers.com/showthread.php?t=846237&highlight=bell
you can thank him for that. I used JK3 because of the issues JK4 was causing. I wouldn't use JK4 but that' up to you.
again you can use either odin or CWM to flash the modem. once you flash the modem you should be able to register on the network. you might not have internet, so you will need to go in and edit your access point name. Located in your phone here:
Settings | wireless and network | Mobile Networks | access point names
If it is blank click the menu button and New APN, all you need for sasktel's is a name, can be whatever and APN, the APN should be "inet.stm.sk.ca" without the quotes. Leave everything else default and save it. you will have to click the bullet after you created it so it knows to use it. should be good after that. For bell just do a quick google search for bell apn or bell access point name, i'm sure someone has posted on xda also.
I am not responsible if you brick your phone, this is entirely on you if that happens.
Thanks man
That's what I have been looking for . A step by step tutorial how is the rom working for you I will give it a shot . I hope sd card Won't die on me again .I can deal with other problems but what could u do when sd card dies
on u .Thanks!
Hey no problem, by default the voodoo lag fix is disabled but honestly you won't need it.....
Sent from my GT-I9000 using XDA App
Nice, one of the great posts ever on xda. Is there any advantage to running darky's ROM? My SGS on JL2 has been good, and battery life seems awesome now that I turned off automated email checking.
adamge said:
Nice, one of the great posts ever on xda. Is there any advantage to running darky's ROM? My SGS on JL2 has been good, and battery life seems awesome now that I turned off automated email checking.
Click to expand...
Click to collapse
Pretty much preference I guess. I love Darky's ROM but JL2 was good, Darky's seems faster it's built upon 2.2.1 and I read Samsung did some kernel upgrades so that's why it's faster. If you do try it out just make sure you can get into recovery and download mode first.
i can confirm that Darkys rom works, I'm running 7.6 atm. I did notice that the APN settings in my original settings were missing ports numbers for data.
I tried this and it did not work, I still don't have data connection and I am on Bell canada.
Are u still getting text's? If so then you are registered on the network, all you have to do is go into your access point names and create an entry, then highlight it after it's saved. See my post above
Sent from my GT-I9000 using XDA App
I tried to use ROM manager to update my rom to overstock, this did not work so well. It installed fine but then the battery refused to charge and all sorts of wierd problems so I used my backup to uninstall and that failed. I downloaded Odin3 v1.7 and downloaded the original stock firmware(eclair) and that failed. I then used UGJH2 and the phone will boot and see the galaxy s load but then the screen goes blank and vibrates periodically. in the recovery (3e) it says Can't mount /dev/block/st110. The last official firmware install was KC1 through kies but I can't find that anywhere is there any hope for this(sweating cause wife might find out)
I am also on sasktel and am an impulsive flasher (1-5 times daily) Heres an easy, fast fix. GO here:
http://www.darkyrom.com/community/index.php?threads/guide-installing-rc5-easy.2382/
go to section enabled "For GT-I9000 users only" and follow step by step. You can stop at step 2 if you want to leave your rom stock samsung or do last few steps to have darkys on there. EIther way once done you'll also have to enable the 850 band *#2263# then enable wcdma 850 option. Also you will have to manually enter your APN under network options. I use inet.stm.sk.ca for sasktel. Note that the Ficeto_JVB.zip download there includes all needed to flash (.pit file, rom, odin). THis is always my fail safe method after boot loops ( I always screw something up playing around lol).
ps: also depending how desperate you are and how trusting you are, I work at sasktels head office in the cornwall and if you wish I am sure I could take 15 mins out of my day tomorrow to do this for you, although you will not be able to get through security so you will have to trust me taking off with your phone lol. email me at [email protected] if needed.
trouble is I can't put things on SD card because I can't get it to load android
You won't be able to load eclair through Odin because JL2 installed a new SBL (secondary boot loader). Go to samfirmware.com, download JL2, and use odin to flash that. Once that's flashed it should fix your issues. Then, if you want a custom ROM, try the romkitchen (romkitchen.org).
problem solved!! turns out darkyrom did fix my phone, I couldn't push the zip file to my phone but their tar file got my phone working! Thanks for all the help
Dougustine said:
I tried to use ROM manager to update my rom to overstock, this did not work so well. It installed fine but then the battery refused to charge and all sorts of wierd problems so I used my backup to uninstall and that failed. I downloaded Odin3 v1.7 and downloaded the original stock firmware(eclair) and that failed. I then used UGJH2 and the phone will boot and see the galaxy s load but then the screen goes blank and vibrates periodically. in the recovery (3e) it says Can't mount /dev/block/st110. The last official firmware install was KC1 through kies but I can't find that anywhere is there any hope for this(sweating cause wife might find out)
Click to expand...
Click to collapse
I loled, I've been in the same boat, wife is always asking me why I always have to mess around with stuff. Shoulda seen her face after I soft bricked the phone the first time.
Just rooted my phone
I am new to this, I can do all kinda of things with my pc but with my phone a different story lol. I don't understand when you say "Eclair". Is that a different model or is that stock. I am too from sasktel.
Android 2.1 is Eclaire, 2.2 is Froyo and 2.3 is Gingerbread... Ice cream is next 4.0
hi guys, I know this is an old post but has anyone successfully unlocked their Sasktel i9000 vibrant without paying any unlock code service? has anyone tried anything like the SGS Unlock Pro that claimed to unlock all GSM galaxy S phones but did not list Sasktel? anyways, from the sound of it is Darky's rom currently the best for i9000's? I wanted to try CM9, so i did the super 1 click root and followed the CM wiki page to push clockwork recovery to the phone through Heimdall Suite but both times i tried failed and stuck in a boot loop so both times i ended up going through Odin to fix it. (super 1 click root didnt seem to stick b/c i lost superuser after fixing the phone w/ Odin, is that normal?)
anyways i had a very unique situation, originally had a Bell i9000m but died 1 week later tried to fix it numerous times for 7-8 months ( i live in U.S., and Sammy refuse to fix it b/c i dont have a canadian address they can send it back to b.s.) anyways finally landed myself a dead i9000m w/ broken screen, so i took both apart and put the working parts together. now 1 working phone with 3 problems: 1) so it seems that it's currently locked to Sasktel (it can be done but i'm curious if there is a cheaper way or even free) 2) CM wiki suggested Heimdall push CW recovery cause boot loop (some on xda suggested flashing the phone back to 2.2 (or 2.1??) first) 3) i was playing around and click on screen update and lose my touch keys ever since (ppl also suggest flashing it back to 2.1 and reupdate the keys, but will a bell i9000m 2.1 stock rom be compatible w/ the i9000m from Sasktel?)
anyways lots of questions there but if anyone can answer anyone of these would be greatly appreciated.
thanks in advance
Update: problem 1 is taken cared of. SGS Unlock Pro worked like a charm. tested, working. other 2 problem still unsolved.
I got a GNOTE from negri on 11/9. It seems it was s polish version. It has been working wonderfully on ATT (after adding in APN manually for 3g/H+ -- voice worked out of box).
I rebooted Today (11/13) and now it has the crossed out circle instead of bars and says "Insert sim" when I start to do cellular related activities.
I have Seated and reseated; nothing. pulled the sim and put back in my SGT (phone enabled) and it works. Put back in GNOTE, still no sim detected! Stuffed SIM in my N1; it works.
Any suggestions?
I had a similar SIM card issue when I tried to activate the 1700MHz band in Service mode (for fun). Wipes and stuff didn't solve anything. The way to revert it for me was flashing a full stock Samsung firmware in Odin.
Can you provide more details on how you did this?
Where does one get a full stock sammy note firmware?
Are there some good instructions on this?
I have flashed my SGT via odin several times. Same odin? Same process?
In the development section you will find some versions.
The key for me was flashing a new Modem (Radio/base band) image via Odin I think. I changed Kernels and ROM's but only flashing a ROM including the Modem got rid of my SIM issue. Not sure because in the end I flashed a full N7000OXAKJ1 firmware in Odin from here:
http://forum.xda-developers.com/showthread.php?t=1310513
It did the trick, though the tread is dead. I think any ROM including Modem might help, I currently running the 2.3.6 N7000ZSKK1 firmware and it is great, also included a Modem.
http://forum.xda-developers.com/showthread.php?t=1342797
fwelland said:
I got a GNOTE from negri on 11/9. It seems it was s polish version. It has been working wonderfully on ATT (after adding in APN manually for 3g/H+ -- voice worked out of box).
I rebooted Today (11/13) and now it has the crossed out circle instead of bars and says "Insert sim" when I start to do cellular related activities.
I have Seated and reseated; nothing. pulled the sim and put back in my SGT (phone enabled) and it works. Put back in GNOTE, still no sim detected! Stuffed SIM in my N1; it works.
Any suggestions?
Click to expand...
Click to collapse
when this happened to me, also due to turning on 1700, I was able to reset my phone by doing a factory reset. Unless your modem.bin is corrupted, you should not have flash a new rom.
- frank.
ugh....
you mean factory reset via Settings->Privacy->Factory Reset?
Tried that... No affect. Is there another way to do this?
Was hoping to fix w/o the flash. NOTE: I did go into that service menu with the 3G Freq are listed. I was curious when I saw the post. But I never changed anything. Just saw the screen and thought "neato". I wonder if there is another service screen that has an option for 'unfuck'???
Still searching for answers, before trying the ROM route...
fwelland said:
ugh....
you mean factory reset via Settings->Privacy->Factory Reset?
Tried that... No affect. Is there another way to do this?
Was hoping to fix w/o the flash. NOTE: I did go into that service menu with the 3G Freq are listed. I was curious when I saw the post. But I never changed anything. Just saw the screen and thought "neato". I wonder if there is another service screen that has an option for 'unfuck'???
Still searching for answers, before trying the ROM route...
Click to expand...
Click to collapse
Here is Chodthewacko posted about it:
http://forum.xda-developers.com/showthread.php?t=1335920
Factory reset and toggle band settings seems to have worked for him. I got frustrated and Odin flashed everything, that worked for me.
whoa....
when I try that procedure (* # * # 1 9 7 3 2 8 6 4 0 # * # * ) I get a pretty empty screen...can't do much of anything...just some useless buttons on the bottom of screen when I select the menu button...
I think I recall seeing another number for doing a similar thing...
fwelland said:
I got a GNOTE from negri on 11/9. It seems it was s polish version. It has been working wonderfully on ATT (after adding in APN manually for 3g/H+ -- voice worked out of box).
I rebooted Today (11/13) and now it has the crossed out circle instead of bars and says "Insert sim" when I start to do cellular related activities.
I have Seated and reseated; nothing. pulled the sim and put back in my SGT (phone enabled) and it works. Put back in GNOTE, still no sim detected! Stuffed SIM in my N1; it works.
Any suggestions?
Click to expand...
Click to collapse
OMG I have the EXACT same issue as you, and I got mine from NEGRI also! It was working perfectly until last night --- all of a sudden I got that circle and I've been trying to fix it since then! Please keep me posted if you find a solution, I was going to try and contact Negri tomorrow for an RMA.
still nothing.
I did a root. No changes...
I did a rom flash of kk1 ... no changes....
I was trying to reflash the modem with KJ6 modem....but have a signature failed problem...
now what???
I solved my issue by a combo of those steps.
I did full flash in Odin of jk1. When I rebooted that didn't solve things so I wanted to flash the other recommendation, kk the Chinese rom.
Upon entering recovery I noticed I lost 2e and was on 3e. So I had to download chainfire's rooted jk1 kernel and do that zerg rush to get root. It was while I was doing that that suddenly my similar got recognized. By the time it finished installing the rooter kernel I had full reception again. I flashed kk just for good measure and its been smooth since. Hope it works for you too and I'd love to know what the heck broke it in the first place??
Sent from my GT-N7000 using XDA App
hi fwelland, it's hk1981...so you tried the rom flash and it didn't work?
Hi hk1981,
No the KK1 rom flashed fine. By all accounts it works well, except that pesky phone part. This KK1 rom is really 'clean' and very little bloat-ware and it installs a vanilla boot animation (not a carrier one). All that is nice, but didn't help my problem
I did notice a peculiar thing: while in recovery (android recovery, not cwm) I get some warning about "CSC something or other, fixing".
I have a short list of things to try before I have exhausted my DIY options -- the post just above looks promising.
I think the answer is out there. We just need to keep looking and keep attention on this thread and others like it. This place and others like it are a huge help and I'd like to solve it and then give back a good set of instructions.
FWIW: I wonder if there was some voodoo in the polish rom that caused some issues in the modem when a different than expected sim was installed? Or if one of those funky polish apps that updated it self before I could turn off auto-updates has something to do with it (doubt this -- I don't think apps can do stuff unless rooted...)...
Still searching....I got this other pesky problem to deal with now: w-o-r-k
fwelland said:
Hi hk1981,
No the KK1 rom flashed fine. By all accounts it works well, except that pesky phone part. This KK1 rom is really 'clean' and very little bloat-ware and it installs a vanilla boot animation (not a carrier one). All that is nice, but didn't help my problem
I did notice a peculiar thing: while in recovery (android recovery, not cwm) I get some warning about "CSC something or other, fixing".
I have a short list of things to try before I have exhausted my DIY options -- the post just above looks promising.
I think the answer is out there. We just need to keep looking and keep attention on this thread and others like it. This place and others like it are a huge help and I'd like to solve it and then give back a good set of instructions.
FWIW: I wonder if there was some voodoo in the polish rom that caused some issues in the modem when a different than expected sim was installed? Or if one of those funky polish apps that updated it self before I could turn off auto-updates has something to do with it (doubt this -- I don't think apps can do stuff unless rooted...)...
Still searching....I got this other pesky problem to deal with now: w-o-r-k
Click to expand...
Click to collapse
I had that problem too, it doesn't detect that CSC and then goes ahead and applies something. Check to see if you are in 3e recovery, I think you are after having flashed vanilla JK1.
Re-flash Chainfire's rooted kernal for your appropriate version and then go back into recovery and it should be 3e and you can flash thru CWM then.
Also note; each time I flashed, I also wiped data/cache/davlik just to be sure.
yes it does say:
Code:
Android system recover (3e).
So I will need to try the methods you (crippenx) suggested.
FWIW, the CSC message that I get when I first enter recovery is:
Code:
# MANUAL MODE #
--Updating application...
Successfully update application.
--Appling Multi-CSC...
Installing Multi-CSC
Applied the CSC-code 'TGY'
Sucessfully applied multi-CSC.
I have no idea what this means. It does it every time I enter recovery.
FWIW, I never flashed this gnote with ODIN (I have used ODIN on my SGT several times). I got to KK1 by first rooting via http://forum.xda-developers.com/showthread.php?t=1329360 (using 'forget the above steps') and then using the CWM 'kk1-wipe.zip' from here http://forum.xda-developers.com/showthread.php?t=1342797 -- I didn't use ODIN to get to kk1.
I see on the Root/Unroot thread, there is a KK1 kernel option for 'simple'. I think I will try that with rooted already script.
But I am open to any/all suggestions...
Code:
Baseband
N7000XXKJ6
Kernel
2.6.35.7-N7000ZSKK1-CL706440
[email protected] #2
Build Number
GINGERBREAD.ZSKK1
fwelland said:
whoa....
when I try that procedure (* # * # 1 9 7 3 2 8 6 4 0 # * # * ) I get a pretty empty screen...can't do much of anything...just some useless buttons on the bottom of screen when I select the menu button...
I think I recall seeing another number for doing a similar thing...
Click to expand...
Click to collapse
My rough guess is that the phone has a list of 'valid service menu options', and it cross references it with what is on the SIM card.
Once the phone decides it's not going to read your sim card, the service menu is blank. This is a real headache.
That's why once I set the 1700+2100 combo, and my phone boycotted my sim, I wasn't able to set it back.
That's really dumb, imho, to have a one way toggle like that. I'm fine for settings to enable/disable other settings, but for a setting to disable itself? ugh.
I would really like to know what's going on. I was planning on switching to AT&T before my next trip (which is soon) but I can't risk my phone glitching out like that during the trip.
Actually, the ROM is on my SD card so I guess it wouldn't be THAT horrible, but it's certainly not something I want to do. Perhaps we just need a way to flash back the modem.bin, assuming it's corrupted.
- Frank
Sorry typo on my part. You are in 3e recovery because of that base flash, now you need 2e recovery which you can get via chainfire's rooted kernel. His installation procedure runs a batch file that uses that zerg rush exploit which I gather is partially from gingerbreak. It was during this procedure that my baseband suddenly came back, my sim card finally detected.
Once that was done, I entered 2e cwm with volume up,power,middle button and did erase of data,cache,davlik and then flashed kk rom via zip file.
Sent from my GT-N7000 using XDA App
fwelland said:
yes it does say:
Code:
Android system recover (3e).
So I will need to try the methods you (crippenx) suggested.
FWIW, the CSC message that I get when I first enter recovery is:
Code:
# MANUAL MODE #
--Updating application...
Successfully update application.
--Appling Multi-CSC...
Installing Multi-CSC
Applied the CSC-code 'TGY'
Sucessfully applied multi-CSC.
I have no idea what this means. It does it every time I enter recovery.
FWIW, I never flashed this gnote with ODIN (I have used ODIN on my SGT several times). I got to KK1 by first rooting via http://forum.xda-developers.com/showthread.php?t=1329360 (using 'forget the above steps') and then using the CWM 'kk1-wipe.zip' from here http://forum.xda-developers.com/showthread.php?t=1342797 -- I didn't use ODIN to get to kk1.
I see on the Root/Unroot thread, there is a KK1 kernel option for 'simple'. I think I will try that with rooted already script.
But I am open to any/all suggestions...
Code:
Baseband
N7000XXKJ6
Kernel
2.6.35.7-N7000ZSKK1-CL706440
[email protected] #2
Build Number
GINGERBREAD.ZSKK1
Click to expand...
Click to collapse
For me flashing all partitions via Odin worked (no pit file or repartition). Tried all sort of stuff from recovery first with no result.
I don't know what partition flash from Odin did the trick, but you could try Odin flashing a Modem separately and check if that works. If not try the rest?
Finally got back to this.
After much fusing I finally got KK1 and cwm working. It was odd, I had to re-run the whole root process again.
At that point I could apply the KJ6 modem w/o any problems (via cwm)
no dice!
Still dead!
Not sure where to go next???
Can some one provide a few details about flashing a modem,rom and/or kernel via ODIN? Perhaps that method will work....
fwelland said:
Finally got back to this.
After much fusing I finally got KK1 and cwm working. It was odd, I had to re-run the whole root process again.
At that point I could apply the KJ6 modem w/o any problems (via cwm)
no dice!
Still dead!
Not sure where to go next???
Can some one provide a few details about flashing a modem,rom and/or kernel via ODIN? Perhaps that method will work....
Click to expand...
Click to collapse
Oh when you flashed jk1 I assumed you did it the old way via Odin and the multiple files. That's how I did it and you're right, that may be what fixed it as when I used to brick my sgs and sgs2, it was always a full Odin flash of stock that brought it back from the dead
To flash in Odin put your phone in download mode. Fire up Odin. In csc point to csc file. In phone section point to modem and for PDA you point to the code file. Don't put anything for pit or bootloader and unchecked the repartition toggle.
Connect your phone and wait for Odin to detect it and show yellow in the status window. Press start and you're good to go. Hope this does it!
Sent from my GT-N7000 using XDA App
Hi guys, I know I need to make this short but I want it to be clear anyway. This is crazy I wanted nothing to do with smartphones 3-4 days ago because all the carriers rip us off with huge bills to get them. But low and behold when my cheap flip phone died after 3 years of loyal daily work a friend of mine offered me his Galaxy S i9000m for a good price. Started playing with the device and having a strong software/computer background started having a lot of fun with all the applications and was amazed with the possibilities (Networking, ipcam whatever) that just kept multiplying until I fell upon applications that needed something called gingerbread... Anyways I can tell you I learned a ****load in 48hours...
So I installed Samsung Kies, it found me the update and put it on for me.. (2.3.3 Gingerbread) then the nightmare started. The phone would boot, and would randomly reboot a random number of times until it could finally stay on and this could last from 2-30 minutes. So I thought, I'll just do a factory reset, to realise that its "STUCK" in 2.3.3 once its updated no going back to 2.1 or 2.2 easily.
Started looking around for ways to downgrade, and EVERY SINGLE LINK redirects to these 'mass download' sites that end up saying the firmwares were taken down for copyright issues. So desperate to find something, I fell upon a multiple CSC FROYO 2.2 firmware for the i9000 and was able to flash that in download mode the phone worked fine, except for me being very curious about the fact that I lost the "M" in my model description...
So started reading this thread(Mostly because I had already realised that with this non i9000m rom I had lost the 3 button DOWNLOAD MODE which i Had before) **** : http://androidforums.com/galaxy-s-a...flashing-darky-v9-gt-i9000m-minimal-risk.html
Got it rooted, got clockwork on, never managed to get the voodoo kernel working had errors in CWM.. so I was ready to give up until my eyes caught the
"*#*#2663#*#*
Then click Touch key FW update"
Which I thought would be neat to try.
NIGHTMARE, now BACK and MENU are dead, I understand that this is because I am running a non i9000m ROM and that updating the firmware rendered them unusable.
I came accross a post : http://forum.xda-developers.com/showthread.php?t=869492
Where this problem is adressed, I pretty much understand everything that should be done to get this back on its feet (right now the phone is still working I can use it at least 75% of its functions work except no back and menu)
Where I need your help : I'm not too sure how to attack this the right way, since I can't get into download mode I understand flashing is now more complicated to accomplish and now that I know that I need a i9000m firmware how can I find that...
Sorry for the long post I know I'm a noob here but I wanted to prove I had done all my homework to get where I'm at now seeking help from you guys!
Thanks a lot
Mat
By the way : Galaxy S GT i9000m currently on a 2.2 i9000 rom, my carrier is BELL. (Canada)
So there's no way of updating to 2.3.3 using Kies?
The only thing I can think of is getting a USB jig from ebay, which makes the i9000 go to download mode instantly. Good luck!
Alright, so I used CHECK FUS, and was able to get the i9000m stock BELL firmware YAY
now the help I need is to flash it correctly and find a way to get past the no download mode problem, would be very appreciated,
thanks guys
No, similar minds Sepharite, I also thought of redoing the Kies method, and then going back again if I needed to but now Samsung Kies says "Your device does not support firmware updates through Kies" Wow.. useful app, a samsung native app can't even detect it's own fricking hardware.
Thanks
UPdate : Was able to restore the 3 button "DOWNLOAD MODE" with a little tutorial online. Now I tried flashing my i9000m with ODIN, it flashed all the way and I get a i9000M logo now but it gets to the splash S logo and keeps rebooting never gets into the actual android setup is there something I did wrong?
In Odin all I put was the "BELL i19000m stock ROM" under PDA and wrote it. The device rebooted after flash but there still seems to be something I haven't done right.
Thanks guys
Please help guys, I know some of you out there have got this stuff nailed down!
Did you flash with a 1 file ROM or a 3 file ROM?
Using the UGKG3 ROM that you can fine here:
http://forum.xda-developers.com/showthread.php?t=1102881
Place the 3 files in their respective places (PDA, PHONE, CSC), for the PIT file, select the 512 pit file that should have come with ODIN, connect the phone, wait for ID:COM to turn yellow, and press Start.
That should get you going again. You may get apps that force close, so you'll need to delete the apps data and then reinstall them.
Hey thanks a lot man ya my flash was a SINGLE FILE, I bricked it yesterday trying to flash a different ROM since I had nothing to lose, I just got it working again on the old 9000 ****ty version that my back and menu keys don't work...
Now for some reason the USB JIG doesn'T work anymore after a couple of uses... could something have been damaged by doing it many times?
And your original roms section they are all unavailable due to copyright did you check the links before sending them?
When you say get the stock roms, I was able to get the UGKG3 file, but what about the versions? When I look at the north american section of the 2.2 version
UGKC1/UGKC1/BMCKC1/Sbl
UGJL2/UGJL2/BMCJL2/Sbl
UGJK3/UGJK3/BMCJK3
which one of the three suits me?
Thanks for your help, and if I get this running and go back and update my touch key firmwares with the right "Vibrant / 9000M" roms I should get them working again?
PS : I'm also very preoccupied by the fact that the USB JIG fix doesn'T seem to pop download mode anymore because this version of the ROM that I have has Download mode not working with the 3 button method. :S I wonder whats going on, but basically if I get your ROMS working the first time It'll fix everything but if it crashes then I lose the galaxy haha
Not sure why the USB jig doesn't work anymore. I have a couple and have only tested them on my phone to make sure they work, but they did not work on a Galaxy S II that I tried it on.
I just checked and the download link for the UGKG3 ROM at multiupload (downloading from multiupload), still works (you need to enter the captcha phrase).
The site megaupload was shut down by the US gov't, so that one won't work.
EDIT: UGKC1/UGKC1/BMCKC1/Sbl is the latest Froyo release from Bell. That's what mine and my wife's gt-i9000m phones came with.
She's still running it on hers.
Ok sorry for all these posts, basically when you said UGKG3 you want me to get the 2.3.3 ROM on ? Is that right? What if I Want to put on 2.2 to be sure I have no trouble with it since I'm in all this mess because the Kies update to Gingerbread had my phone in a bad state.
Thanks a lot by the way!
Sorry your post refreshed right after I did mine. Alright cool so I'll try the one you say your wife is running, I had made myself a JIG with a stock Samsung wire, it was working fine with a 300K resistor and I decided to solder it on and then it stopped working after that.... maybe the actual "usb plug" is damaged from the soldering heat I guess I'd have to try another wire, but anyway I'll try to download the 2.2 I just got the UGKG3 3 FILE rom downloaded one of the links did work!
But I'm a little worried about 2.3.3
I'll try to see if i can download the 2.2 first.
I mean basically... these roms shouldn't jam during transfer i Guess
One other thing I see different confusing information, is it important for me to click 'update bootloader" with these stock roms since these files contain an 'SBL' ? Because both times I bricked it was with an "update bootloader checked" firmware update trying to put the ARIES 3 button method fix as a boot.bin and sbl.bin
Fanks..
Files with SBL in the name already have the bootloader included in the PDA file, so "update bootloader" should NOT be checked.
That reassures me, because the only times it did jammed was when the bootloader was checked! THanks a lot blackrose i'll go out and buy another usb cable because I destroyed mine making my JIG. And I'll try yours out. I was reading a lot on another thread and found this one guy who flashed the JL2 one to save his keys instead of the C1 you said your wife was running, whats the main difference between those two and which one should I start with?
Update : I got a new wire, flashed the KC1 version of the firmware, everything goes fine, I did a repartition with the 512 PIT, it reboots the phone, loads all files in a prompt in yellow and there are no errors that appear, the phone reboots after writing 'successful update' and then goes to the galaxy logo and jams there and does the ONE vibrate, PAUSE, 2 vibrate on a black screen forever. The advantage of having successfully flashed a 9000M ROM allows me to have access to my DOWNLOAD MODE 3 button method, but ever since I flashed that 2.2 i9000 XXJP2 (seems its a euro version) off a torrent I found on the web (When I was desperate to find a functioning 2.2 working version) it seems as though it doesn'T want to boot with any other rom than that one, because all the 9000M roms that I've tried so far flash correctly, and the logo actually changed from i9000 to i9000M on the startup, but they just don't boot.. what could be missing it doesn't seem to be much???
Thanks Mat
If any of this can help, the device was rooted, I was following the darky's mod i9000M guide so I had previously installed the CLOCKWORK MOD and that's as far as I got because my eyes caught the FIRMWARE TOUCH KEY UPDATE which ruined my keys.
Could any of this have screwed something that stops my other roms from booting?
Thanks guys I really want to get this phone up and working again as I don't have much money and am afraid I'll have to cancel with my phone company if I just can'T get this running. I am also willing to make a significant donation to whoever can help me.
You in Canada right? Where abouts?
Sent from my GT-I9000 using xda premium
Quebec province
Alright, if this can help anybody my whole problme is solved.
I flashed the ****JL2**** the KC1 did not boot, the JL2 did.
Once inside JL2, I was able to update my TOUCH KEY FIRMWARE *#*#2663#*#* and everything went back to normal
I have no idea why the KC1 does not work, bugs me out.
So, I recently installed CM9 and on top of that SlimBean 2.6. Both worked otherwise perfectly, but I couldn't get my 3g connetion to work on either one, unless I turned "National Roaming" on. I checked the Acces Point Name settings, and they seem to be fine. I can't find my service provider on the Network operators list though. I read that a new modem migth do the trick, but I have no idea if that will help or which modem to choose.
I had a similar problem after going to CM9. I even had my APN (access point names) settings disappear randomly also.
Solution for me was to turn 'airplane mode' on....wait 30 seconds then turn off.
Strange as it sounds but it actually worked for me. But in the end, (after 1 day) I changed to samsungized 12.1 JB rom because I found that I had to use that airplane mode on/off alot and was too much of a pain.
Hope this helps.
If not, I'd revert back to a stock rom then upgrade to a stable JB rom
Tried just that, but no luck so far. Any other suggestions?
Taatero said:
Tried just that, but no luck so far. Any other suggestions?
Click to expand...
Click to collapse
Id recommend trying a good stable stock rom with a 512_pit repartition via Odin, just to see it it improves the modem or not.
The rom im going to suggest has a replacement Modem file within.
Might sort the problem.
Ive used this stock rom to fix my many problems ive had after custom roms.( Mainly format errors i had )
Its from 'HotFile' site and took me around 20 mins to download it.
But it might be worth the wait in your case.
Rom File:
http://hotfile.com/dl/140301534/be8872c/I9000XXJVU_I9000OXAJVU_OXA.rar.html
Here Is the Pit File and Odin version I used. ( 3rd box down the page )
http://forum.xda-developers.com/showthread.php?t=1102881
And heres the Root file. Get " CF-Root-XX_OXA_JVU_2.3.6-v4.3-CWM3RFS " :
http://forum.xda-developers.com/showpost.php?p=15188469
s1_odin_20100512.pit Goes in PIT ( repartition checked )
CODE_I9000XXJVU_CL851880_REV03_user_low_ship.tar.md5 Goes in PDA
GT-I9000-CSC-MULTI-OXAJVU.tar.md5 Goes in CSC
MODEM_I9000XXJVU_REV_00_CL1092175.tar.md5 Goes in phone
Sorry if im telling you what you already know with how to use Odin, just making sure.
After rom install pop this root on with Odin via download mode.
CF-Root-XX_OXA_JVU_2.3.6-v4.3-CWM3RFS goes in PDA
I reckon its worth a shot.
Must make sure the 3 wipes are done before the rom install. I learned this the hard way and messed my
phone up for a while.
Problem solved! I did some googling around, and found a solution. Apparently my carrier, Saunalahti, is known for having problems with 3g on custom roms. I found out that a nexus s modem by the name of i9020AUCKF1 might work. And sure enough, it did the trick! No more roaming! Anyway, thanks for taking the time to help me!