Related
There have been those that run into problems after installing the XXJP3I9000 update on the Samsung Captivate and attempt to reboot into recovery mode. The issue that they have is that since the Captivate has no physical home button to select an option like you can with the Galaxy S, you can't select an option, and therefore you can't reboot your device regularly. While I am in this same problem and have not figured out a solution, I have started this thread to post what knowledge I have about this issue so that others may help get this issue figured out. If anyone has information on how to fix this problem, please comment below. Let's fix this!
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
First of all, the key combinations that standardly would work with the original captivate firmware will not work anymore. Pressing all three buttons (Vol+, Vol - and Power) will only power cycle the phone, that is, until you let up on the buttons. Pressing Vol+ and Vol- and then plugging your phone into the computer will also do nothing. (By nothing I mean will take you back to the recovery menu)
Every key combination will only take you back to the recovery menu, so key combinations seem to be out.
If you boot into recovery mode, take out the battery and put it back in, all the while keeping the phone plugged in to the computer, the phone will enter the "POWER RESET OR UNKNOWN UPLOAD MODE", which will show your device in windows as being a Samsung USB Composite Device and a Samsung Mobile Modem (gadget serial, Windows 7) While this may be helpful, you cannot run ODIN or ADB in this mode, nor does this allow disk access. If you have Samsung Kies installed, it will detect a device, but will never complete loading it.
Other information with this method: On the phone screen, as well as showing "POWER RESET OR UNKNOWN UPLOAD DEVICE" the screen will also show the following in red:
RST_STAT =0X1
PMIC_IRQ1 =0X0
PMIC_IRQ2 =0x0
PMIC_IRQ3 =0x4
PMIC_STATUS1 =0x40
PMIC_STATUS2 =0x2c
If this helps anybody, it was a pleasure
Another method I found briefly was that after installing Kies, and rebooting the phone into recovery mode (again) my computer detected four new devices, two of them being Samsung Android devices and one being a disk drive. Potentially, without freezing or error, the drivers that are included with the Kies software will detect and allow for disk management while the phone is in recovery mode. Three of the four devices installed without error for me, but the fourth, the actual Android device, continued to say "installing device" until I unplugged the phone out of frustration. It has since not detected those four devices again, and I have yet to figure out how to do that again. The nice thing about that was that although the adb.exe reboot download command did not work, adb.exe did detect the phone. if this is true then rebooting normally or into download mode should be easy.
The last thing I noticed is that button furthest to the left on the main screen on the captivate will close the recovery menu when pressed, and leave the background behind, and then will reopen the recovery menu when pressed again. This is showing me that the four touch buttons are operable, but not configured. If it were possible to reconfigure the actions that pressing these buttons do, then it would be easy to be able to reboot the device normally.
I have compiled information to the best of my ability, and here is a question to ask, that I think will help solve the problem. Can the captivate with I9000 2.2 software run adb in recovery mode?
Comments, Questions, and Most of all, answers would be appreciated for me, as well as for other users with the same problem as I. Hopefully, this thread can be the solving point for this problem.
Many Thanks,
TouchofDestiny
The n00b who isn't a n00b at all
An Update: The reason that the combinations don't work for me or either people is because they (and I) fail to install the captivate kernel, and that is making the volume power button controls useless.
same here i put froyo from the galaxy s i9000 and i cant change the rom or get into recoverymode because buttons dont work man this sucks and 3G or Edge doesnt work.....
You're problem is a little different. If you can't get into recovery mode, than that means you aren't in recovery mode, which means you can use ADB to enter download mode and use Odin to flash your phone. I have given up looking for a solution, and have sent my phone back to AT&T for a replacement. Since I'm still in my thirty day trial period, it doesn't matter if I used different firmware or not. Hopefully others won't get into the situation I had. For me, this thread is complete.
brandon9721 said:
same here i put froyo from the galaxy s i9000 and i cant change the rom or get into recoverymode because buttons dont work man this sucks and 3G or Edge doesnt work.....
Click to expand...
Click to collapse
hi,
I solved the same problem doing this:
start odin.
take out battery. plug in USB. press both volume buttons. insert battery while pressing those buttons.
Done. download mode should appear.
yep, same boat
I am in the same position here. I downloaded the froyo leak and installed it with odin, no problem there. Upon startup into froyo, all was good, except my phone was stuck in horizontal mode until I tilted it vertical, *then* it would go horizontal. So basically I am 90 degrees off kilter. I decided to look around for another rom to try, and in the process managed to get stuck in recovery mode. Couldn't tell ya what firmware I have, just what is on the endless recovery screen that I cannot get out of!
I have no external microSD card, only the SIM card, and no way to get it recognized on my XP or win 7 system.
Really, really stuck here, guys. I do have the androidsdk installed, if there is a way to get it to reboot. As it is, adb cannot see the device, so I am looking at a truly bricked phone.
And yes, this is a US phone, which is why the power button and home button are not mapped (I assume).
I am DESPERATE for some help here!
and while I am at it...
I WAS able to get into download mode with the shovel guy originally by using the 2 volume keys+power, usb (odin up), battery in, release power.
No more. No key combo works.
Totally bricked the Samsung, which is supposed to be impossible!
pkrouse said:
I WAS able to get into download mode with the shovel guy originally by using the 2 volume keys+power, usb (odin up), battery in, release power.
No more. No key combo works.
Totally bricked the Samsung, which is supposed to be impossible!
Click to expand...
Click to collapse
when you are on the i9000 rom the only button that will get you in download mode is the vol down
That's HUGE!
You, sir, are a gentleman, scholar, and all-round smart guy! How did I miss that? I coulda SWORN I was getting into download mode with both volume keys. I've never been so happy to see a little Dalek dude with a shovel in my LIFE. 2 minutes in the one-click installer and now I'm back in business!
Thanks for helping a terrified owner out, and preventing a trip to the AT&T store.
I cannot go to download mode
I have the same problem here. Stuck in the recovery mode after upgrade the froyo and had the orientation problem. How do you go into download mode or power reset or unknown upload mode? Any button combination doesnt seem to work for me.
How do I do?
Please HELP. I am struggling here
Thanks
xaga150 said:
I have the same problem here. Stuck in the recovery mode after upgrade the froyo and had the orientation problem. How do you go into download mode or power reset or unknown upload mode? Any button combination doesnt seem to work for me.
How do I do?
Please HELP. I am struggling here
Thanks
Click to expand...
Click to collapse
the key to the i9000 rom/kernel button combo is VOL DOWN + using the USB trick. do not press vol up + down, just the down while you are plugging in the usb cable
i too am stuck in recovery mode. the only way i can get into download mode is by using both volume buttons. just holding the down button just sends me to revoery mode as well. how can i fix my phone in download mode?
nevermind, reinstalled 2.2 and it works now.
Eureka I got it...I think
I installed froyo 2.2 i9000 on my captivate and got stuck in recovery mode...power button doesnt select and when I hold down the up and down vol buttons I couldnt get the downloading icon anymore either. Then I remembered something from another post....
Home + Vol Down + Power = Downloading Icon
It worked for me....let me know if this helped....I'm officially unbricked.
Hey. I'm in the same boat. My Captivate has I9000 firmware running it and it won't run properly. I can't access the settings to enable USB debugging in order to boot in either Recovery or Download using adb and no button combination works for me. I can't use button combos to boot into either Recovery or Download mode.
Does anybody have any idea what is going on and how to fix this?
JPBetley said:
Hey. I'm in the same boat. My Captivate has I9000 firmware running it and it won't run properly. I can't access the settings to enable USB debugging in order to boot in either Recovery or Download using adb and no button combination works for me. I can't use button combos to boot into either Recovery or Download mode.
Does anybody have any idea what is going on and how to fix this?
Click to expand...
Click to collapse
JPBentley-- Since the I9000 firmware is set to use physical buttons, and the Captivate doesn't contain any, once you get into recovery mode, you cannot get out. The standard Captivate key combinations to get into download mode do not work, as do the combinations to get into download mode via the I9000 firmware. Basically, you get to a dead end. Unless there is some way to flash the phone's ROM outside of download mode, which I doubt, your best bet is to return the phone for a replacement. After haggling around with AT&T for a while, they admitted that installing the I9000 ROM doesn't invalidate your warranty, so they should take it back. They did with mine, and now I'm running the official Froyo leak. Good luck with your new phone!
SOLUTION
For all those that are having this problem, Ive struggled with it & tried EVERY possible button combination & nothing worked.
The ONLY solutions I have found is to use a usb JIG. Take out the battery, sim card & sd card, plug in the Usb JIG & put the batter back in. Give it a couple of seconds & I'tll enter recovery mode without pushing any buttons. You dont even need to push the power button, it's that simple.
Here is an image of how to make one if you are electronically inclined, personally I am not so I found a local electronic parts store & they put on together for me.
1.bp.blogspot.com/_3KjgtwnRiWM/TNTyjkZGquI/AAAAAAAABL4/7NSmqrYmkmU/s640/i900.jpg
If you want, you can also buy one online, I cant post a link becuase Im a new member but just search for "samsung usb jig" on ebay.com & youll find plenty.
shop.ebay.com/?_from=R40&_trksid=p5197.m570.l1313&_nkw=samsung+usb+jig&_sacat=See-All-Categories
yes, i think you need to build a jig or buy one online if you want to play with custom rom. you may not need it now, but you may need it just in case.
http://cgi.ebay.com/ws/eBayISAPI.dl...47234&ssPageName=STRK:MESELX:IT#ht_511wt_1139
agustinpac said:
hi,
I solved the same problem doing this:
start odin.
take out battery. plug in USB. press both volume buttons. insert battery while pressing those buttons.
Done. download mode should appear.
Click to expand...
Click to collapse
OMG you saved my life
thx so much for your post
I have the same problem, i can get into recovery mode. I can also get to download mode but Odin doesnt see my phone and neither does adb. By pulling the battery with no buttons pushed it goes straight into recovery mode. Looks like I have a brick now. If anybody has any suggestions please let me know.
drowe24 said:
I have the same problem, i can get into recovery mode. I can also get to download mode but Odin doesnt see my phone and neither does adb. By pulling the battery with no buttons pushed it goes straight into recovery mode. Looks like I have a brick now. If anybody has any suggestions please let me know.
Click to expand...
Click to collapse
That's not even close to a brick. Are you using a usb port closest to the motherboard on your pc? Is your cable good? Make or buy a jig, that will put your phone into download mode.
Sent from my blazing fast Captivate running Continuum GB ROM using Tapatalk Pro
I had been using my Captivate for a while, and used Kies mini to upgrade to Froyo, and everything had been working fine until randomly the phone wouldn't boot.
It would take forever to go from the AT&T home screen, and would lag through the galaxy s intro, and then stop.
I tried to use Recovery mode, and it didn't work, so I tried to use Odin3 to flash back to stock.
Now it won't go past the Logo screen, and recovery mode doesn't work, but download mode still does. I have tried Odin one click, and Odin three click v 1.0, 1.3, and 1.7. I've used the .tar and the .pit from Breakin' Ranh's [Guide] How to Recover a Captivate to Stock 2.1 Eclair JH7
It keeps getting stuck in a boot loop after odin, no matter what I do.
Any suggestions?
Using SGH-i897
1007
first boot takes along time to build new files and delvik.. are you sure you waited long enough?
keep trying to get into recovery. try holding the buttons a little after the screen comes on.
factory wipe/ clear phone/
It keeps going to the AT&T logo screen for like 10 seconds, and then goes to the spinning wheel/battery charging screen, and then reboots.
Can't get into recovery mode through it, still.
a different .tar package.... dunno about that one..
or flash to 2.2 tar package
I have to use rom manager to get to recovery on my captivate
Sent from my SAMSUNG-SGH-I897 using XDA Premium App
I was able to use a dragon rom to get it to boot, but now my phone wont give me any access to my internal sd card, and won't mount my external, so I can't download rom manager because I "have no room" Where do I go from here?
I've already tried formatting both cards, and it seems like nothing happens whenever I click on format.
you dont need rom manager....ever
Then what does he need?
Sent from my SAMSUNG-SGH-I897 using XDA Premium App
stuck in the same position
I can get into download mode (only with a JIG tho) but when I go back to stock with Odin (or try to) it's just stuck in the AT & T logo screen, it doesn't go beyond that, how do I get into recovery mode, press both Volume buttons and Power button, when the AT&T screen comes release the Power button right?
Need some help please!
you might need to flash the 3 button fix but keep trying, if you get into recovery clear data and cache. but first boot always takes a long time as it has to build delvak cache and more... try flashing again, with the 3 button fix att rom.
3 button fix? to get into download mode you mean? I CAN get into download mode (with the jig) but not into recovery mode :-s
I have no idea how to flash it without being in the Stock rom, any help?
download is 2 buttons
recovery is 3 button.
some phones loose the 3 button combo to get into recovery.
in that case you need to flash the stock rom with 3 button fix.
it is for Att only so i dont know much more.
After Odin, I was in a boot loop yesterday. I plan on writing it up in a new thread to see if someone can help me understand what happened (cause I have Odined and modded two different cappys without issue) but here is how I was able to recover.
After Odin was complete and said successful, it reboots the phone.
Upon reboot I was in the ATT boot loop. After Odin, I lost both three button recovery and 2 button download (both of these worked before Odin). I don’t have a JIG so no way of getting to download mode.
I read to try the following sequence after reading it other posts.
1. Pull battery, sim, SD card and unplug the USB. Let it sit for a minute.
2. Plug in the USB cable.
3. Holding all three buttons, plug in the battery.
4. The battery charge (grey) should be seen on the phone. After the phone screen goes black twice let go of the power button.
This worked for me once, after several attempts.
Now that the phone booted back up, I did a master clear with Odin.
Upon reboot right back in to the ATT boot loop screen.
Was not having any luck with the steps above after several attempts.
Here is how I eventually recovered.
1. I opened Odin on the PC.
2. Pulled the battery and USB for a minute or two then replaced it and plugged in the USB cable.
3. After few cycles of black battery icon and spinning wheel, the batter icon turned green (like normal when you turn your phone off and plug it in). Sometimes this only took two cycles and sometimes many cycles (or a few minutes).
4. Once the battery icon was green, I hit the power button.
5. As soon as you see the ATT screen, pull the USB cable and the phone booted (if I left the USB plugged in, the phone went back to the black battery screen after the ATT screen).
6. I copied the correct Update.zip and Rom to my SD card.
From here I tried to boot into recovery via ADB.
The phone rebooted but back into the ATT boot loop.
Following the second set of steps above (2-3 times), I was finally able to get into Clockwork recovery.
From here I flashed Phoenix Unleashed.
After the flash rebooted and the phone seems to be running fine now (with the exception that I lost my 3 and 2 button combos, but that will be for a different thread).
From the Power Menu, I can get into download mode or Recovery no prob.
Not sure if this is something that will work for others but wanted to throw it out there just in case.
It never booted for me, so this is what I did
For anoyone that might find this thread, Odin 1 Click didn't work for me, so I flashed back into stock using Odin (not the 1 click version, another one), here are some links that proved to be very helpful (I ended up Flashing to Serependity 6.4):
http://forum.xda-developers.com/showthread.php?t=1031749
http://www.youtube.com/watch?v=Rdn5GoRjhn0
http://forum.xda-developers.com/showpost.php?p=10056254&postcount=36
http://forum.xda-developers.com/showthread.php?t=884364
http://forum.xda-developers.com/showthread.php?t=919816
http://android-roms.info/roms/80-Serendipity
http://serendipityrom.weebly.com/download.html
FIXED:
Used this version of Odin to get me into recovery mode:
http://www.multiupload.com/PM9TNZWL84
Once I got that, I realized my internal SD card wasn't mounting properly, and used http://forum.xda-developers.com/showpost.php?p=10056254&postcount=36
this thread to finish flashing back to stock.
I have been having the hardest time lately with my captivate but the newest problem is that the lock button doesnt work at all it seems to be a hardware issue rather than a software issue and i am currently running cyanogenmod7
Right now i want to restore it to stock rom but no matter what i try i cant get it into download mode or if i get it into recovery mode i cant d anything because the lock button is broken
Any suggestions?
adb command can get you into download and recovery. jig can also get you into download
just tested: Search soft key is enter/select, back is back, menu is up, home is down
ok well i have it plugged in to my computer and set to screen never sleep while charging so i can still use it but when i try to flash it to stock using odin 3 it wont recongize that its in debugging mode is CM7 not compatible with it or something?
well i tried entering download mode and it started and just hung so idk what to do now cuz i took the battery out and now it starts up and says at and t world phone and is stuck there so i can no longer enter download mode or my phone so am i totally screwed at this point?
is my best bet go to the at and t store and be like i was updating kies with it and enter download mode and it got unplugged while updating?
Well, if your phone still turns on, its still possible to fix it, however, you shouldn't have any problems getting one replaced.
Just tell them the phone said you had an update and you hit ok, play dumb and act upset.
Sent from my SAMSUNG-SGH-I897 using Tapatalk
Hi um I'm pretty new to Android phones, and my Captivate's stuck in a bootloop...
I had CyanogenMod 9 on it, based on ICS 4.0.4, which i still have the .zip for if necessary. But I think I did something stupid... in the recovery (which said something about CWMrecovery) mode, I absent-mindedly formatted the /system directory... derp....
Now basically the phone shows the AT&T logo, then shows some kind of recovery screen, it only flashes up for a short time but I can see in the background both an android, like stock recovery mode, and the logo from ROM manager (or something very similar). There is some text at the bottom but it's very small and only flashes up for a split second so I can't read it... and what's worse, it won't boot into recovery...
I'm not exactly sure how to even do it, but random combinations of the volume & power buttons and home.. screen-area-thing work eventually.. but it's just not working now, as i hold the buttons it either just keeps rebooting before it gets past the AT&T logo or ignoring it completely, showing the recovery screen then rebooting again anyway
Sorry it's kinda long.. I tried to be detailed XD
tl;dr CM9 rom Captivate, formatted /system, stuck in bootloop, recovery mode won't work
Any help would be much appreciated
Edit: Forgot to say, I've searched around already but I haven't found anyone else who's bootloop is caused by formatting /system -.-
re flash the rom. you erased the rom.
dont wipe dont format just flash the rom again. you should be back as if it never happened.
If your in a boot loop you might want to invest in a jig, only $6 on eBay
You also said recovery doesn't work? Have you tried putting it into download mode?
Sent from my SGH-I897 using Tapatalk 2
This might help you:
http://forum.cyanogenmod.com/topic/39685-stuck-on-boot-loop/
If not google Samsung captivate boot loop. Lots of info on how to fix out there. Sorry I don't work on many Samsung phones. Primarily HTC.
Sent from my Inspire 4G using XDA
jig will not help bootloop.
you are freaking out because of the bootloop and not holding the button combo for recovery long enough.
take out the battery. and replace
hold both volume buttons
then hold power
keep buttons held for 5 seconds AFTER screen comes on.
if your phone turns on and starts to boot, you have recovery and download.
TRusselo said:
jig will not help boot loop
Click to expand...
Click to collapse
You sure? Fixed my phone from boot loop!
Sent from my SGH-I897 using Tapatalk 2
TRusselo said:
jig will not help bootloop.
you are freaking out because of the bootloop and not holding the button combo for recovery long enough.
take out the battery. and replace
hold both volume buttons
then hold power
keep buttons held for 5 seconds AFTER screen comes on.
if your phone turns on and starts to boot, you have recovery and download.
Click to expand...
Click to collapse
Tried that, isn't working :\ it just ignores it, shows the recovery screen realy quick then reboots again...
I've had this happen on my captivate...only option is to flash back to a stock ROM and work your way back up to CM9 or whatever you were trying to flash originally. To do this your gonna have to get into download mode. A jiff is your best friend in this situation as suggested by several others. however if the button combo for download mode works for you, that is best. Try unplugging the battery, wait for like 10 seconds and plug back in. Have a PC running, and make sure you have the drivers installed. have the USB cable plugged into your computer, and while holding both the volume buttons down, plug the cable into your phone as well. This should put you into download mode and your good to go.
Sent from my SGH-I897 using XDA
thanks cmilldrummin (and everyone else)
I got my phone into download mode fine... but i don't think I have the drivers :s (googling still, but can't find them so far)
Also I got it into recovery mode earlier, re-flashed the same custom ROM but when I tried to load it it just kept loading with the blue android on a skateboard until the battery ran out (It was the same one, CM9)
Is the like actual android system openable in download mode? so I could re-write the /system folder? if not I guess I'll just try to re-flash a stock rom then upgrade.. *crosses fingers*
Best way is to flash back to stock and start fresh.
Sent from my Serendipity VII flashed Captivate using xda premium
Np Dolei, but yea back to stock is best, gives you a nice clean slate, with no glitches or errors
Sent from my SGH-I897 using XDA
TRusselo is right. The other posts here are taking the sledgehammer approach for a simple fix. If you cannot get into recovery mode - you're doing it wrong, try again. reflash your rom from recovery and all done.
Dolei said:
Hi um I'm pretty new to Android phones, and my Captivate's stuck in a bootloop...
I had CyanogenMod 9 on it, based on ICS 4.0.4, which i still have the .zip for if necessary. But I think I did something stupid... in the recovery (which said something about CWMrecovery) mode, I absent-mindedly formatted the /system directory... derp....
Now basically the phone shows the AT&T logo, then shows some kind of recovery screen, it only flashes up for a short time but I can see in the background both an android, like stock recovery mode, and the logo from ROM manager (or something very similar). There is some text at the bottom but it's very small and only flashes up for a split second so I can't read it... and what's worse, it won't boot into recovery...
I'm not exactly sure how to even do it, but random combinations of the volume & power buttons and home.. screen-area-thing work eventually.. but it's just not working now, as i hold the buttons it either just keeps rebooting before it gets past the AT&T logo or ignoring it completely, showing the recovery screen then rebooting again anyway
Sorry it's kinda long.. I tried to be detailed XD
tl;dr CM9 rom Captivate, formatted /system, stuck in bootloop, recovery mode won't work
Any help would be much appreciated
Edit: Forgot to say, I've searched around already but I haven't found anyone else who's bootloop is caused by formatting /system -.-
Click to expand...
Click to collapse
TRusselo said:
re flash the rom. you erased the rom.
dont wipe dont format just flash the rom again. you should be back as if it never happened.
Click to expand...
Click to collapse
TRusselo said:
jig will not help bootloop.
you are freaking out because of the bootloop and not holding the button combo for recovery long enough.
take out the battery. and replace
hold both volume buttons
then hold power
keep buttons held for 5 seconds AFTER screen comes on.
if your phone turns on and starts to boot, you have recovery and download.
Click to expand...
Click to collapse
Try doing this, this has worked for me since I can't get into recovery with the traditional button combo method of holding all three buttons at the same time.
Turn the phone off. Hold the power button, vol up, vol down. Once the ATT boot screen comes on, let go of the power button. Keep holding the volume buttons and voila, you're in recovery.
Agree. Definitely go back to stock if possible first.
Sent from my Inspire 4G using XDA
Hi, I need some help or guides on a problem I just got.
I have a rooted S3 LTE (I9305), which seems to be soft bricked, if I understand what I have read so far. I need to either get it to work again, or at least a way to access files, so I can extract some data from it.
The situation is as follows:
I came home the night between sunday and monday, from a holiday, on which I had used the phone to take a lot of photos. At the point where I entered my car, the phone was working. I used the GPS to take, where I parked my car. Switched off the screen, and drove home.
When I got home, I could see the screen was hanging at the boot logo. So it must have crashed and rebooted it self at one point - don't know when.
Tried to restart 4-5 times, but only got to the boot screen. Pulled the bat. but still the same.
Suddently at one point, I couldn't even get to the logo screen, instead it just shows white and black stripes across the screen.
If I'm lucky I can get into download mode, but only around every 10 time or so.
I managed to keep it in download mode at one point, and through Odin wanted to re-flash my device, but it failed saying it need a pit file.
So this is where I stand now. Is there a way to access the phone from my computer, so I could download the photos taken, or can I flash it without loosing any of the photos and if so how?
if you have a custom recovery installed you could maybe try to plug it in to a PC and mount the USB storage via the menu
SammyPasz said:
if you have a custom recovery installed you could maybe try to plug it in to a PC and mount the USB storage via the menu
Click to expand...
Click to collapse
Which menu are you thinking about? The PC doesn't recognize the phone, as a device. Can't find it anywhere. And in the download mode, I can't do anything on the phone, or at least it doesn't reacts.
Anyone? I'm a bit lost here
Mhystique said:
Which menu are you thinking about? The PC doesn't recognize the phone, as a device. Can't find it anywhere. And in the download mode, I can't do anything on the phone, or at least it doesn't reacts.
Click to expand...
Click to collapse
Do you have a custom recovery installed like Clockwork mod or TWRP recovery manager?? If you have you'll be able to access it by switching your phone off then holding power up + home + power until you see the boot animation
SammyPasz said:
Do you have a custom recovery installed like Clockwork mod or TWRP recovery manager?? If you have you'll be able to access it by switching your phone off then holding power up + home + power until you see the boot animation
Click to expand...
Click to collapse
Offcause I forgot the phone at Work, so can't test to be sure. But if I recall correctly I have TWRP installed.
But don't think I can get into it. The only compination of buttons that I had success with, was volume down + home + power into the download mode, as I said. But that isn't even all the times I can get into that.
Update:
Yes, as I expected I couldn't start it with volumen up + home + power, all I get is the black and white stripes.