Odin problem "There is no memory" - Galaxy S I9000 Q&A, Help & Troubleshooting

Please i need some help, i was on Gingerbread XXJVO Rom with fugumod 3.9 ultra kernel, done a format in CWM. Then tried to flash XXJVH stock rom in ODIN but message in ODIN says
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> There is no memory.
<OSM> PDA_XWJVH_Deodexed_Zipaligned.tar.md5 is invalid.
<OSM> End...
Now my phone wont work properly, have tried XWJVB and XXJPU roms but same thing... have tried 512/803 pits please help me! Thanks

are you sure that this is not the developpers version of the roms ? you should get the one here and try again :
http://forum.xda-developers.com/showthread.php?t=1011901
Also choose the one with bootloader or you won't be able to start your phone.

Change your bootloader back to froyo version.
Use Odin 1.0. Connect the phone in download mode and hit Start without loading anything. Wait a few seconds until the program says: Done! Do this a few times if the process hangs.
Then flash some Eclair rom with repartition.
After that make a full hard reset *2767*3855#. Now I think your phone should be fine.
If you want to install Gingerbread again, flash the new bootloaders.

celeronix said:
Change your bootloader back to froyo version.
Use Odin 1.0. Connect the phone in download mode and hit Start without loading anything. Wait a few seconds until the program says: Done! Do this a few times if the process hangs.
Then flash some Eclair rom with repartition.
After that make a full hard reset *2767*3855#. Now I think your phone should be fine.
If you want to install Gingerbread again, flash the new bootloaders.
Click to expand...
Click to collapse
May i know what does it make to hit start whitout loading anything on odin 1.0 ?

I can hardly say what exactly does that intervention, but as far as I know it fixes some NAND flash problems on software bricked devices.

jscnz81 said:
Please i need some help, i was on Gingerbread XXJVO Rom with fugumod 3.9 ultra kernel, done a format in CWM. Then tried to flash XXJVH stock rom in ODIN but message in ODIN says
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> There is no memory.
<OSM> PDA_XWJVH_Deodexed_Zipaligned.tar.md5 is invalid.
<OSM> End...
Now my phone wont work properly, have tried XWJVB and XXJPU roms but same thing... have tried 512/803 pits please help me! Thanks
Click to expand...
Click to collapse
Are you sure you have enough memory on your PC? Odin may need much memory to check md5, i think nothing has changed on your sgs because Odin can't check the file hash.

Your computer memory can't cause such kind of a problem.
It's probably connected with the bootloader.

celeronix said:
Your computer memory can't cause such kind of a problem.
It's probably connected with the bootloader.
Click to expand...
Click to collapse
I'm pretty sure this has nothing to do with the bootloader. If he got bootloop, it's because odin found a pit, it partitionned the phone so there is no more rom in the phone, and then failed to hash the files and didn't flash. Can you link me where you downloaded your software ? Or try to go back on your working XXJVO ?

You need to repartition your device. In my opinion, it looks like the /system partition is too small. (Check pit file used) And wrong section. Please post in the Q&A Section in the future.

chadouming said:
I'm pretty sure this has nothing to do with the bootloader. If he got bootloop, it's because odin found a pit, it partitionned the phone so there is no more rom in the phone, and then failed to hash the files and didn't flash. Can you link me where you downloaded your software ? Or try to go back on your working XXJVO ?
Click to expand...
Click to collapse
He doesn't got a bootloop. The phone just doesn't work. All you can do is to put it in download mode. That's it.
I had exactly the same problem with mine as described above. And yes, you should make a repartition along with the other stuff.
What software are you talking about?

Related

[SOLVED] Semi-bricked my new Galaxy S

Hey guys,
Urgent help needed...
I bought a new Galaxy S a month ago and I experience the lag and normally only a reboot could solve it. Then Froyo came by in Kies, and after the update it was still laggy. So i revolved to rooting with SuperOneClick and applying OCLF lagfix... It was running fine until after a week or two, the phone started to experience serious lags in the homescreen, the app screen and various force closes from apps.
Then i tried formatting the phone in recovery, i did a recovery and data wipe but only after that i realized that i forgot to unroot and clear the lagfix, but even then i had no problems until this morning the phone was lag again.
Assuming that it was the root and the lagfix that i forgot to undo, i tot of trying to flash my phone with Odin using the firmware i got from samfirmware.com
Downloaded I9000DXJPA from samfirmware and used Odin 1.3 to flash my phone, there wasnt any problems with the flash and Odin reported it being successful, but my phone only boots up to the Galaxy S GT-I9000 screen, not even booting to the 'S' screen. Waited for quite a long time then i tried booting into recovery but no luck, recovery doesnt work, but download mode works for me.... I tried flashing a few times and still no luck, changed to Odin 1.7 and tried flashing several times as well...
Please someone give me some advice or help me.... Please~
-----------------------------------------------------------------
Problems solved, did a flash using Odin to I9000XXJPU and the phone booted into recovery requesting for a factory reset and done.
Added Darky's v5.5 Gingerbread mod as well.
Thanks for those who replied
I tried flashing back to stock Eclair 2.1 firmware which i kept last time from samfirmware.com
but Odin didnt allow me to the following are the message shown
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MD5 hash value is invalid
<OSM> AP_S1_PDA_DXJG4_CL458501.tar.md5 is invalid.
<OSM> End...
try a new base firmware. the files you have are probably corrupted.
cross88 said:
I tried flashing back to stock Eclair 2.1 firmware which i kept last time from samfirmware.com
but Odin didnt allow me to the following are the message shown
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MD5 hash value is invalid
<OSM> AP_S1_PDA_DXJG4_CL458501.tar.md5 is invalid.
<OSM> End...
Click to expand...
Click to collapse
JM8 always works for me maybe try that. Have you flashed with odin before? If so how did it go?
racerboy3801 said:
try a new base firmware. the files you have are probably corrupted.
Click to expand...
Click to collapse
Ya. The asian JPA firmware posted on samfirmware was corrupted and not working. I tried many many times and yet not working, got advices from another forum and got JPU flashed into my SGS and now its running fine. ^^ thanks
tragusman said:
JM8 always works for me maybe try that. Have you flashed with odin before? If so how did it go?
Click to expand...
Click to collapse
Ya all the flashing is done with Odin but it seems that the problem is that the stock JPA firmware from samfirmware was not working or corrupted...
Problems solved with JPU + Darky's Mod ^^
Anyway thanks.

[Q] Brick after trying to install Gingerbread

Hi i am on a captivate i896. I tried to install I897UCKF1. Everything was fine till it had to reboot after installation then i couldn't do anything. I can't install stock rom, the phone reboots with att logo and it doesn't do anything. I think its the bootloader that is messed up and i don't know how to install the older ones or just to be able to get back to rogers 2.1 stock or ATT 2.1 stock. I am always stuck at this screen :
<ID:0/009> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I897UCKF1_CL273832_REV02_user_low_ship.tar.md 5 is valid.
<OSM> MODEM_I897UCKF1_CL1017518_REV02.tar.md5 is valid.
<OSM> SGH-I897-CSC-ATTKF1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
When i try to install JF6 it stalls at File Analysis....
Please help.
try and get it into download mode. Its not bricked justyet.
accordztech said:
try and get it into download mode. Its not bricked justyet.
Click to expand...
Click to collapse
i tried to get in download mode and i can but i just can't get to install any stock roms i can't do anything. Do you know if i can install the booloaders or anything?
ramih2085 said:
i tried to get in download mode and i can but i just can't get to install any stock roms i can't do anything. Do you know if i can install the booloaders or anything?
Click to expand...
Click to collapse
Restart your computer and if running windows vista or 7 make sure you run Odin as an administrator and possibly even compatibility mode. I have had that problem before and a restart fixed it.
Sent from my GT-I9000 using XDA Premium App
tried it, still the same thing...
i read something about bootloaders are different for the gingerbread build than the normal eclair and froyo. I don't know if i have to do something different. I just wanna get back to stock 2.1 from there i can find my way out...
ramih2085 said:
i read something about bootloaders are different for the gingerbread build than the normal eclair and froyo. I don't know if i have to do something different. I just wanna get back to stock 2.1 from there i can find my way out...
Click to expand...
Click to collapse
Did you try the Odin 1 click for stock JF6 posted by Designgears in the development forum? It flashes both bootloaders that are need to get back to stock.
yes i did, and it stalls at file analysis....usually it works but now i don't know why!
ramih2085 said:
yes i did, and it stalls at file analysis....usually it works but now i don't know why!
Click to expand...
Click to collapse
Try a different usb port and/or cable.
jhernand1102 said:
Try a different usb port and/or cable.
Click to expand...
Click to collapse
I tried all the usb ports on my computers. Odin always detects my phone but for some reason i can't install anything on it.
ramih2085 said:
I tried all the usb ports on my computers. Odin always detects my phone but for some reason i can't install anything on it.
Click to expand...
Click to collapse
I has an issue like this once where it would get stuck during the flash and my screen would turn different colors. I got it to work by using the full odin where you can select the pda & pit files. Give it a try.
jhernand1102 said:
I has an issue like this once where it would get stuck during the flash and my screen would turn different colors. I got it to work by using the full odin where you can select the pda & pit files. Give it a try.
Click to expand...
Click to collapse
i did that too, nothing worked...
anyone has an idea of what to do?
ramih2085 said:
anyone has an idea of what to do?
Click to expand...
Click to collapse
Try using the Odin version provided in this thread:
http://forum.xda-developers.com/showthread.php?t=1127249
It should restore to stock 2.3.3 Gingerbread. Not sure if being a UCKF1 poses a problem in your device or location, but I suppose it's worth a shot. Note that the rest of the instructions is to root the device, you don't need to do all those other steps. Just download the Odin One-Click, and try it out. Regards.
ramih2085 said:
I tried all the usb ports on my computers. Odin always detects my phone but for some reason i can't install anything on it.
Click to expand...
Click to collapse
I have the same problem . Please help ! Thankss.
ramih2085 said:
i did that too, nothing worked...
Click to expand...
Click to collapse
my AT&T Captivate is 2.2 stock with root,unlocked . I flash Stock+voodoo-froyo I897 UCKB1.tar. it said FAIL. try to go back 2.1 stock but it can't do anything.Please help! Thanks
ramih2085 said:
i did that too, nothing worked...
Click to expand...
Click to collapse
what is PIT files ? and how can I get it ? I want to try it .Thanks .
Mr. Janderson said:
Try using the Odin version provided in this thread:
http://forum.xda-developers.com/showthread.php?t=1127249
It should restore to stock 2.3.3 Gingerbread. Not sure if being a UCKF1 poses a problem in your device or location, but I suppose it's worth a shot. Note that the rest of the instructions is to root the device, you don't need to do all those other steps. Just download the Odin One-Click, and try it out. Regards.
Click to expand...
Click to collapse
i tried that and here is the log:
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
also for the pit file, it is usually included in the zip file with odin 3 click so if you download odin 1 click, u dont need that file.
captivate bricked
flashing power off charging logo when try to reboot . no down load mode cant do sh%t.help please
See the "Captivate Connection Issues and Download Mode Help" that is linked in my signature below.
If that does not help then...
Sounds like you are gonna need a JIG. See my signature link below for links to how to make one or where to buy one.
When you get back into download mode, you are gonna need to flash a Stock Firmware of your choice. There is a sticky thread in the Captivate Development Forum that you will need to see for those.

[Q] Need help! Galaxy Note does not boot anymore. [SOLVED]

My Galaxy note does not boot anymore. I can boot CWM but when I flash a ROM or format /system the device hangs.
Any help would be greatly appreciated..
Have you tried wipe cache from recovery?
And wat exact happened before error occured?
Thanks for your quick reply
I got stuck on the Samsung N7000 screen after a reboot. I'm running [ROM][04.04.12] imilka's AOSP ICS v08 [IMM76D/4.0.4]
Formating data/cache works but when you install a ROM it just sits on installing update. I've tried flashing multiple ROMS.
If I select unmount /system or format /system it hangs as well. Same happens when I try to restore my backup from yesterday. I can only boot CWM or download mode at the moment.
I've only had HTC phones before so I don't have any Samsung experience.
Which kernel you had ?
What exact error occurs, when you flashing ROM?
I was using the kernel that came with the ROM.
I was just doing a reboot after the device has been powered off for a few hours. Nothing special.
Whe I try to flash a ROM now it just hangs at installing system forever. My guess is that something has screwed up the system parttion because I'm unable to format it now using CWM.
Any other way to try repartition the device?
try using flash with PC Odin
here is stock ROM
http://forum.xda-developers.com/showthread.php?t=1424997
download N flash using PC odin, you can find installation guide in post#2
Trying it right now. Phone is in download mode. Odin reports:
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_N7000XXLC1_CL1003701_REV02_user_low_ship.tar.md5 is valid.
<OSM> MODEM_N7000XXLB2_REV_05_CL1106002.tar.md5 is valid.
<OSM> GT-N7000-MULTI-CSC-OXALC1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/011> Odin v.3 engine (ID:11)..
<ID:0/011> File analysis..
<ID:0/011> SetupConnection..
for about 5 minutes. Is it normal that it takes this long to start the connection?
It seems this is connection error
Try reinstalling driver on PC
connect device to dierct main board USB slot(rear side PC)
close kies/anti virus if running
Problem solved. Thanks a lot for your help!
Selecting 1 option at a time worked (maybe coincidence) Did PDA > Phone > CSC.
Phone boots
N7000XXLC1---------2.3.6-------2012 March----------N7000OXALC1-----------Open Europe----------------------------- Download (wipe)
now and I'll probably keep it that way untill Samsung released ICS.
Learned something about Samsung phones and Odin today. Used to do everything with ADB and fastboot with HTC devices.
Thanks again!!

Bricked Tab :(

hi people,
So here is my issue, i rooted my tab after having it about a year and wanted to install a custom rom, installed RomManager from the market and installed the clockwork recovery mod, BUT i picked galaxy tab 10.1 when it asked me what phone i had, as there was no other option. I checked on google first and it seems other people with the 8.9 are using the clockwork recovery mod so i thought it was safe.
Now its dead and powers up to the samsung logo, and then dies again.
Help! (currently i am draining the battery as it is mentioned in another thread in this forum)
Thanks
(tried the APX thing in nvflash and it was a no go)
epictwiglet said:
hi people,
So here is my issue, i rooted my tab after having it about a year and wanted to install a custom rom, installed RomManager from the market and installed the clockwork recovery mod, BUT i picked galaxy tab 10.1 when it asked me what phone i had, as there was no other option. I checked on google first and it seems other people with the 8.9 are using the clockwork recovery mod so i thought it was safe.
Now its dead and powers up to the samsung logo, and then dies again.
Help! (currently i am draining the battery as it is mentioned in another thread in this forum)
Thanks
(tried the APX thing in nvflash and it was a no go)
Click to expand...
Click to collapse
It's alright. Go to the guide in my signature and read up about ODIN because you will use it to save your tablet. It's all there in FAQs, How-tos and the Toolkit at the end.
i highly recommend checking out nirogu325's guide for an explanation of ODIN. it should solve your problem
Download Odin
http://www.google.com/url?sa=t&rct=...IxHp1ISlP2fzGKhtw&sig2=4EbBRrWss7eeO2JNr8TzzA
Download the proper recovery
7310 and 7300
http://forum.xda-developers.com/showthread.php?t=1312218
i957
http://forum.xda-developers.com/showthread.php?t=1462770
Power on the tablet, you may need to charge it.
As it is powering on hold down the power and the vol down button
Go into download, not recovery
Connect your tablet to your computer with the USB cable
Open up Odin
You should see box that says PDA, click there and it will want you to find a file. Choice the recovery file
Make sure the box that says partition or repartion are NOT check
then check start and wait. DO NOT touch or disconnect the tablet while it works
bdfull3r said:
i highly recommend checking out nirogu325's guide for an explanation of ODIN. it should solve your problem
Download Odin
http://www.google.com/url?sa=t&rct=...IxHp1ISlP2fzGKhtw&sig2=4EbBRrWss7eeO2JNr8TzzA
Download the proper recovery
7310 and 7300
http://forum.xda-developers.com/showthread.php?t=1312218
i957
http://forum.xda-developers.com/showthread.php?t=1462770
Power on the tablet, you may need to charge it.
As it is powering on hold down the power and the vol down button
Go into download, not recovery
Connect your tablet to your computer with the USB cable
Open up Odin
You should see box that says PDA, click there and it will want you to find a file. Choice the recovery file
Make sure the box that says partition or repartion are NOT check
then check start and wait. DO NOT touch or disconnect the tablet while it works
Click to expand...
Click to collapse
So i dont need the clockwork recovery mod files? just the stock recovery? and it wont boot to download mode so i cant connect it to odin unless im missing something, let me read it again.....
Ok! i have managed to get to download mode, i discharged the tab overnight and plugged it in this morning and he booted past the samsung logo, i cant remember what thread i saw that idea in but it worked. awesome, now to try and flash stock recovery, hope i dont duck it up!
Thanks guys, ill post again if it doesnt work @)
nirogu325 said:
It's alright. Go to the guide in my signature and read up about ODIN because you will use it to save your tablet. It's all there in FAQs, How-tos and the Toolkit at the end.
Click to expand...
Click to collapse
all i get is:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MD5 hash value is invalid
<OSM> recovery.img.md5 is invalid.
<OSM> End...
Booooo, now what? im using an old version of odin, so maybe ill try and new one?
Solved! So i was putting the MD5 file and it wasnt working, so i put the whole .RAR file in and it worked! It wouldnt flash the clockwork recovery mod though so i had to put the stock one back on.
Still it works again, thanks guys.
epictwiglet said:
Solved! So i was putting the MD5 file and it wasnt working, so i put the whole .RAR file in and it worked! It wouldnt flash the clockwork recovery mod though so i had to put the stock one back on.
Still it works again, thanks guys.
Click to expand...
Click to collapse
I am glad you have your tablet back in working order.
Well now that you have the stock recovery, you can attempt to flash the Clockwork recovery again the right way if you want to. You now know how to recovery your tablet if you have a brick again so you don't have anything to lose
hi can someone help me with a brick i957. i am not seeing anything on the lcd its totally black however when i plug the usb to the pc its being recognized as Qualcom hs-usb diagnostics 9006. i thought well maybe i can flash it with odin but this is all i am getting:
<ID:0/155> Added!!
<ID:0/155> Removed!!
<ID:0/155> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CWMR5x_i957_recovery.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/155> Odin v.3 engine (ID:155)..
<ID:0/155> File analysis..
<ID:0/155> SetupConnection..
and its been there for almost 45 mins with no response. any help will be greatly appreciated.
Linkzz said:
hi can someone help me with a brick i957. i am not seeing anything on the lcd its totally black however when i plug the usb to the pc its being recognized as Qualcom hs-usb diagnostics 9006. i thought well maybe i can flash it with odin but this is all i am getting:
Added!!
Removed!!
Added!!
Enter CS for MD5..
Check MD5.. Do not unplug the cable..
Please wait..
CWMR5x_i957_recovery.tar.md5 is valid.
Checking MD5 finished Sucessfully..
Leave CS..
Odin v.3 engine (ID:155)..
File analysis..
SetupConnection..
and its been there for almost 45 mins with no response. any help will be greatly appreciated.
Click to expand...
Click to collapse
If Odin recognizes the tab there is a chance to recover it. What rom are you trying to flash? Go to sammobile.com and get the stock gb rom.
Sent from my SAMSUNG-SGH-I727 using xda app-developers app
i am using a stock rom from sammy roms but same problem
<ID:0/155> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> HOME_I957UCLK4_CL1167230_REV02_user_low_noship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/155> Odin v.3 engine (ID:155)..
<ID:0/155> File analysis..
<ID:0/155> SetupConnection..
Try with odin ver 1.85. I haven't had luck with 3.
Sent from my SAMSUNG-SGH-I727 using xda app-developers app
jd1639 said:
Try with odin ver 1.85. I haven't had luck with 3.
Sent from my SAMSUNG-SGH-I727 using xda app-developers app
Click to expand...
Click to collapse
thats what i have been using; when i try with odin3 v3.07 its not recognizing the tablet
I know it doesn't make sense but keep trying to flash the rom. I've seen it not work for many tries and then it would for some reason. If odin recognizes the tab you are not hard bricked. You should be able to get it to operate again.
Also, use the gb Rom, uckj7
Sent from my SAMSUNG-SGH-I727 using xda app-developers app

[Q] Problem with format data

I installed tablet metrics with xposed installer. Then I used my phone normally for a few days and it started...
The phone started to reboot without reason. It just went crazy. I couldn't use it. Every time it turned on, 15 secs later started to reboot again. So I tried to uninstall xposed installer but didn't work. After doing that, my phone didn't boot anymore. It stayed in the "samsung" part. Then I went to recovery mode and did all the wipes possible, wipe cache, wipe factory reset, etc. Did everything but one, format data. And didn't boot. And as a last hope I did format data.
I shouldn't have done that.
Now I don't know what to do. Need some help, please.
I have installed the TWRP recovery. When I try to reboot it says "no OS installed". There is no way to install from TWRP a new OS ?
If you don't understand me or want me to add some more information just put it in the comments.
I don't speak english very well as you might know. Sorry.
Lele123 said:
I installed tablet metrics with xposed installer. Then I used my phone normally for a few days and it started...
The phone started to reboot without reason. It just went crazy. I couldn't use it. Every time it turned on, 15 secs later started to reboot again. So I tried to uninstall xposed installer but didn't work. After doing that, my phone didn't boot anymore. It stayed in the "samsung" part. Then I went to recovery mode and did all the wipes possible, wipe cache, wipe factory reset, etc. Did everything but one, format data. And didn't boot. And as a last hope I did format data.
I shouldn't have done that.
Now I don't know what to do. Need some help, please.
If you don't understand me or want me to add some more information just put it in the comments.
I don't speak english very well as you might know. Sorry.
Click to expand...
Click to collapse
You are on stock JB? Flash stock firmware with Odin. Do not flash I9070 firmware on I9070P phone, do not flash I9070P firmware on I9070 phone - IT WILL HARDBRICK phone - no more going back.
Odin how to: http://forum.xda-developers.com/showthread.php?t=1985398
Firmwares: samsung-updates.com sammobile.com
Do factory reset after.
shut_down said:
You are on stock JB? Flash stock firmware with Odin. Do not flash I9070 firmware on I9070P phone, do not flash I9070P firmware on I9070 phone - IT WILL HARDBRICK phone - no more going back.
Odin how to: http://forum.xda-developers.com/showthread.php?t=1985398
Firmwares: samsung-updates.com sammobile.com
Do factory reset after.
Click to expand...
Click to collapse
It doesn't work...
The Odin get's stuck in this part:
<ID:0/020> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> HOME_I9070XXLPZ_I9070SERLPZ_660490_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/020> Odin v.3 engine (ID:20)..
<ID:0/020> File analysis..
<ID:0/020> SetupConnection..
Thanks for your comment
Lele123 said:
It doesn't work...
The Odin get's stuck in this part:
<ID:0/020> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> HOME_I9070XXLPZ_I9070SERLPZ_660490_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/020> Odin v.3 engine (ID:20)..
<ID:0/020> File analysis..
<ID:0/020> SetupConnection..
Thanks for your comment
Click to expand...
Click to collapse
Does the size of downloaded firmware match the size written on the page when you start download? I think XXLPZ is one of the oldest FW, try LQL for example.
shut_down said:
Does the size of downloaded firmware match the size written on the page when you start download? I think XXLPZ is one of the oldest FW, try LQL for example.
Click to expand...
Click to collapse
I've tried with XXLQUE and XXLPZ, gives me the same error. I will try with LQL when the download completes
Lele123 said:
I've tried with XXLQUE and XXLPZ, gives me the same error. I will try with LQL when the download completes
Click to expand...
Click to collapse
Try other version of Odin too. 3.0.7 for example.
shut_down said:
Try other version of Odin too. 3.0.7 for example.
Click to expand...
Click to collapse
I did it with LQL, didn't work...
Lele123 said:
I did it with LQL, didn't work...
Click to expand...
Click to collapse
Maybe your phone have some hardware issue, you told that it was rebooting every 15 seconds. Better go to some service centre.

Categories

Resources