Related
Hi,
i have some problems with my new kaiser and my wlan. I'm not able to check my emails or anything else in the web. I can just open my router web-config seite and i can connect to my linux with putty (internal network).
So lang i'm connectet with my PC via ActiveSync evreything is working fine ... but not via wlan, other wlan spots are also working well.
I guess it's something with the mtu value is wrong. I also had to change it on my PC witch is also connectet via the wlan.
Maybe sombodey can give me a tip how to change the mtu value on a WM device. Or how to check the value like on XP by the cmd ("ping -f -l <mtu value> www.microsoft.com").
You can change it via the reg.
Unfortunately I never really looked too deep into it as I have SK Tools & this allows you to view & set the MTU for all functions.
BTW, I believe the default is 0 & the range is 0 - 68 & I also really doubt the MTU is the problem.
i found the problem ...
i changed the energie-mode to performance-optimized instead battery-optimized...
i was already wondering why the Rx-Rate is only working with 1-2MBps ... so i just tryed it out and it's working now ... but why are other networks working well with the battery-optimized configuration?? my router is just 4 meters away from me ...
I am using Myn's Warm Donut, but from what I can tell I've had this problem on most if not all distributions I tried.
When I connect my HTC Touch to my computer via USB (Win7 x64), I can't get windows to detect it, and so I can't access the SD Card.
However, I have found that I can successfully access it by using the replimenu when booting. It does take about a minute before it manages to connect though, but it always works.
Here's what happens when I select Start Recovery Mode:
Code:
USB Connected
Start Charging
msm_hsusb_set_vbus_state(1)
hsusb: OFFLINE -> ONLINE
hsusb: reset controller c5cccc00
usb: notify offline
set address to 1
usb_mass_storage usb_mass_storage: config #1
[About 15 seconds later]
tried to queue zero length request
set address to 2
usb_mass_storage usb_mass_storage: config #1
[About 15 seconds later]
tried to queue zero length request
set address to 1
usb_mass_storage usb_mass_storage: config #1
[About 15 seconds later]
tried to queue zero length request
set address to 2
usb_mass_storage usb_mass_storage: config #1
[USB finally connects and the sdcard is mounted in windows. Total time elapsed since USB was plugged in: about 60 secs]
It always starts working after the fourth try, at address 2.
Do you have any idea what is going on?
Any help would be greatly appreciated!
P.S. I have tried on two different Win7 x64 computers and one XP x86
Tsuushin said:
I am using Myn's Warm Donut, but from what I can tell I've had this problem on most if not all distributions I tried.
When I connect my HTC Touch to my computer via USB (Win7 x64), I can't get windows to detect it, and so I can't access the SD Card.
However, I have found that I can successfully access it by using the replimenu when booting. It does take about a minute before it manages to connect though, but it always works.
Here's what happens when I select Start Recovery Mode:
Code:
USB Connected
Start Charging
msm_hsusb_set_vbus_state(1)
hsusb: OFFLINE -> ONLINE
hsusb: reset controller c5cccc00
usb: notify offline
set address to 1
usb_mass_storage usb_mass_storage: config #1
[About 15 seconds later]
tried to queue zero length request
set address to 2
usb_mass_storage usb_mass_storage: config #1
[About 15 seconds later]
tried to queue zero length request
set address to 1
usb_mass_storage usb_mass_storage: config #1
[About 15 seconds later]
tried to queue zero length request
set address to 2
usb_mass_storage usb_mass_storage: config #1
[USB finally connects and the sdcard is mounted in windows. Total time elapsed since USB was plugged in: about 60 secs]
It always starts working after the fourth try, at address 2.
Do you have any idea what is going on?
Any help would be greatly appreciated!
P.S. I have tried on two different Win7 x64 computers and one XP x86
Click to expand...
Click to collapse
are you using free automount app or the paid dual mount app?
I tried auto mount without any success. Maybe there's system logs I could fetch from somewhere?
Also, do you know if it is normal that it needs about one minute and 4 tries in order to successfully connect in Recovery Mode?
Tsuushin said:
I tried auto mount without any success. Maybe there's system logs I could fetch from somewhere?
Also, do you know if it is normal that it needs about one minute and 4 tries in order to successfully connect in Recovery Mode?
Click to expand...
Click to collapse
did you check the box in the app to enable it after installing it?
Yes
What seems to happen is an endless loop of:
Code:
USB Connected...
Preparing SD Card...
[Wait 15 seconds and repeat]
In the same manner I described earlier.. except it doesn't end up connecting after 4 tries like in recovery mode
EDIT: Oh! I let it go a while longer and after something like 2-3 minutes it finally managed to connect.
Am I the only one experiencing this delay or is it "normal" for our device?
just wait longer. walk away from it for like 5 mins. When im using eclair it takes alot longer than donut. It sems to connect and disconnect like 50 times before actually connecting. This is normal.
It works indeed.
I would be interested in looking at the logs and trying to understand what is happening (and maybe even fix it!).
Does anyone know where I should be looking at?
Guys, I just bought Omnia 2 and it seems the GPS lag so much that it's totally useless. I use Garmin XT and the GPS lags about a couple of minutes. Is it a phone issue or what?
This is what I have done, and it work's (at least for me Omnia i8000):
Change these settings in the registry:
HKEY_LOCAL_MACHINE\System\CurrentControlSet\GPS Intermediate Driver\Drivers\Samsung GPS Hardware\InputBufferSize: set from 4096 to 512
HKEY_LOCAL_MACHINE\System\CurrentControlSet\GPS Intermediate Driver\Drivers\Samsung GPS Hardware\OutputBufferSize: set from 4096 to 512
HKEY_LOCAL_MACHINE\System\CurrentControlSet\GPS Intermediate Driver\Drivers\Samsung GPS Hardware\SleepOnNoData: set from 100 to 0
HKEY_LOCAL_MACHINE\System\CurrentControlSet\GPS Intermediate Driver\Multiplexer\MaxBufferSize: set from 16384 to 1024
The rest is the same as the usual GPS and TomTom settings. I used com port 4 (and 9 for hardware), but you can probably use any other port that hasn't been assigned yet.
nuelo said:
This is what I have done, and it work's (at least for me Omnia i8000):
Change these settings in the registry:
HKEY_LOCAL_MACHINE\System\CurrentControlSet\GPS Intermediate Driver\Drivers\Samsung GPS Hardware\InputBufferSize: set from 4096 to 512
HKEY_LOCAL_MACHINE\System\CurrentControlSet\GPS Intermediate Driver\Drivers\Samsung GPS Hardware\OutputBufferSize: set from 4096 to 512
HKEY_LOCAL_MACHINE\System\CurrentControlSet\GPS Intermediate Driver\Drivers\Samsung GPS Hardware\SleepOnNoData: set from 100 to 0
HKEY_LOCAL_MACHINE\System\CurrentControlSet\GPS Intermediate Driver\Multiplexer\MaxBufferSize: set from 16384 to 1024
The rest is the same as the usual GPS and TomTom settings. I used com port 4 (and 9 for hardware), but you can probably use any other port that hasn't been assigned yet.
Click to expand...
Click to collapse
Is this really working? somebody can also give a hint?
kingchicky said:
Is this really working? somebody can also give a hint?
Click to expand...
Click to collapse
[HKEY_LOCAL_MACHINE\Software\Samsung\RIL\GPS\XTRA]
"Enable"=dword:1
"AutoDownload"=dword:1
"AutoDownloadActiveSync"=dword:1
HKEY_LOCAL_MACHINE\Software\Samsung\RIL\GPS
Accuracy=1 or 4 old 19
Vaccuracy=1 or 4 old 0
ResponseTime=0 old 2
QOPDelay=0 or 1 old 12
MaxLocationAge =0
ServerAddress=
xtra1.gpsonextra.net:80
Timesync= 1 old 0
do that after buck up your reg with a regeditor
and then you have a top class GPS
first time update your extra first time locks in about 2 min in clear sky
and after that in a couple of seconds
does that work .. can any one confirm ?? coz i m having same trouble .. .plzz help !!!!
The one and only FULLY OPERATIONAL Navigation Software is:
IGO8
Try it and find it out
GPS fix
Hi i'm using AGIS NAVFone (Asia), but should work for all GPS devices
First:
Go to Settings>Connectivity>GPS (or something like that)
My phone's in servicing now... sad
Set COM9 to hardware port
COM7 to GPS
Baud Rate: 9600
Gives me a fix ~2min
To make it quicker: Install GPSModDriver here:
forum[.]xda-developers[dot]com/showthread.php?t=571266
What it does:
This Driver installs between your gps application and the GPSID driver that reads the hardware gps data.
Lag is compensated, by guessing your position 'some number' of milliseconds in the future, current course and speed changes are included in the guess.
It corrects for invalid data in the gps strings, Out of range DOP values, and Heading values of 'NaN' (Not A Number). Position, Speed, and course are reported, even though the distance traveled is less than 30 meters.
Click to expand...
Click to collapse
Follow the instructions there to install, and Garmin Mobile XT requires QueStub
Garmin Moble XT (and Others), users:
Garmin Mobile XT, refuses to use the GpsModPort to read gps data, it insists on using the original com port. QueStub is an application that changes the reg entries for the default gps port to the GpsModDriver port, runs the Que program, and restores the values back when Que exits. It is only 5 kb when sitting in memory.
Click to expand...
Click to collapse
So get QueStub 3.10,
and GPSModDriver 3.10
With this you can get ~3s Fix (For me)
Take time to read through that post and feel free to ask any questions.
1sokel said:
[HKEY_LOCAL_MACHINE\Software\Samsung\RIL\GPS\XTRA]
"Enable"=dword:1
"AutoDownload"=dword:1
"AutoDownloadActiveSync"=dword:1
HKEY_LOCAL_MACHINE\Software\Samsung\RIL\GPS
Accuracy=1 or 4 old 19
Vaccuracy=1 or 4 old 0
ResponseTime=0 old 2
QOPDelay=0 or 1 old 12
MaxLocationAge =0
ServerAddress=
xtra1.gpsonextra.net:80
Timesync= 1 old 0
do that after buck up your reg with a regeditor
and then you have a top class GPS
first time update your extra first time locks in about 2 min in clear sky
and after that in a couple of seconds
Click to expand...
Click to collapse
Anyone tried this?
you can test your GPS dialing " *#1472365# "
and there u can change these values to.
nothing appears in the screen when typing these neumbers
i wonder if u can assist.Garmin XT is loaded.First screen ...connect in GPS Garmin.when entering the program tries to connect the Garmin GPS receiver and scans for the connected device and for bluetooth..It has the skip button too.When clicking omit(or skip)program says taht some parts of Garmin mobile xt would not function properly without a valid gps fix.If you click yesthat is go on with skip)screen advises you to aggree on safe driving etc and when you do so screen says that cannot track the Garmin GPS device, asking you if you want to connect with other GPS devices.If you click yes it prompts you that connection is ONLY allowed for the Garmin GPS device.It gives three choices in the bottom.1.Acton completed.2.Activate and 3.Activate (again).When clicking completed gives you the screen ..where to? and map layout (the icon on top left is yellow(not red)and says again that cannot locate the garmin GPS device asking you (again and again)if you would like to be connected with other GPS devices.By clicking no the previous icon appears again (red this time)a map is shown and on top there is the indication that GPS is Inactive!!Sorry for being so detailed but my next action will be to throw the GT program away.Moreover in the screen with indication (system-info) of GPS when clicking prompts you again that connection only with Garmin GPS. Finally both Beeline GPS and GPS tuner work fine in my OMNIA (fully operable) and lastly i wanted Garmin only for the naval charts as I have both Sygic and iGo 8 working perfectly in my device, therefore I hesitate to alter the COM7 to COM4 as both (iGo and Sygic recognize and cooperate with COM7).
Thanks in advance I wonder what am I doing wrong with garmin.
msurg said:
Anyone tried this?
Click to expand...
Click to collapse
Jip, on my omnia II i8000. I use IGO8 and well ... it finds sattelites but it will not connect to them. So no changes on my phone. But you should try it as those register settings will not damage your phone.
HKEY_LOCAL_MACHINE\Software\Samsung\RIL\GPS
Accuracy=1 old 19
Vaccuracy=1 old 0
ResponseTime=0 old 2
QOPDelay=0 old 12
MaxLocationAge =0
ServerAddress=xtra1.gpsonextra.net:80 old empty
TimeSync=1 old 0
HKEY_LOCAL_MACHINE\Software\Samsung\RIL\GPS\XTRA
AutoDownload=1
AutoDownloadActiveSync=1
AutoDownloadWifi=1
DownloadInterval=168
Enable=1
this with I8000XXJD1 locks at cold start in 20-29sec in open sky the only trouble you must have data enable or leave server empty as it is
test it with 3 deferent programs Igo8,iGoprimo,syngic ,mireo black 3,1
there is no need for anything else no drivers no nothing
all you have to do the first time is to get XTRA manual
this also works with omnia 1
try this
setting-system-external gps-programs-port4
and
setting-system-external gps-hardware-port(none) and Baud rate 4800
and
make youe Garmin XT port on 4
Heys guys,
really need some help here usb had been working fine for sometime but now everytime i plug in the usb wether its in download mode or in mass storage or anything usb related it only displays my fone as charging. i have factory reset my device plus formatted internal memory. The usb seems to only charge and not pick up the phone via the pc. has any one got any ideas as would like to flash a custom rom and need to change the kernel but like is say my pc doesnt even detect the phone anymore i have even formatted the laptop to see if that helped and no joy im running windows 7 hope you can help cheers wattsy
p.s i have flashed jpk 2.2 and all went was fine for ages now i cant even flash as the usb is no detected on pc
the phone doesnt even recognise if there is another connection there it just displays chrging and thats all really need some help with this guys
wattsy1612 said:
Heys guys,
really need some help here usb had been working fine for sometime but now everytime i plug in the usb wether its in download mode or in mass storage or anything usb related it only displays my fone as charging. i have factory reset my device plus formatted internal memory. The usb seems to only charge and not pick up the phone via the pc. has any one got any ideas as would like to flash a custom rom and need to change the kernel but like is say my pc doesnt even detect the phone anymore i have even formatted the laptop to see if that helped and no joy im running windows 7 hope you can help cheers wattsy
p.s i have flashed jpk 2.2 and all went was fine for ages now i cant even flash as the usb is no detected on pc
the phone doesnt even recognise if there is another connection there it just displays chrging and thats all really need some help with this guys
Click to expand...
Click to collapse
I currently have the exact same issue.
It would be helpful if anyone has any ideas? Otherwise I think some of the SGS's may be developing faults for some unknown reason.
No device is listed under device manager, and when trying to change the USB connection type whilst the phone is connected it let's you do it, instead of giving the usual message about the USB being connected, which to me eliminates any driver issues.
I have tried two different cables to no avail.
I would try pulling down the device logs but is this possible on a non-rooted phone?
i'm running stock JF3 Vodafone firmware.
Cheers,
MiG
so think it may be a trip to service centre once froyo has been released as im running froyo already and dont think it would go down to well surely someone has an idea what the problem is cheers wattsy
wattsy1612 said:
so think it may be a trip to service centre once froyo has been released as im running froyo already and dont think it would go down to well surely someone has an idea what the problem is cheers wattsy
Click to expand...
Click to collapse
If you have a USB cable handy, run/download the Terminal Emulator from Android market, and run the following command: 'logcat'.
After this plug in your USB cable, and see what appears on screen. I don't have my cable with me right now but will try later to see if any attempt at data is made/lost/failed etc.
tried it its currently saying "unable to open log device '/dev/log/main': permission denied im running unrooted jpk 2.2 cheers mig wattsy
wattsy1612 said:
tried it its currently saying "unable to open log device '/dev/log/main': permission denied im running unrooted jpk 2.2 cheers mig wattsy
Click to expand...
Click to collapse
Might be an issue with Froyo. Check to see if USB Debugging is enabled in Settings > Applications > Development, although I don't think this is required. I'll have a look later with my own phone if not.
treid both ticked/unticked usb debugging still look forward to your results when ur home. its a shame not even odin will flash a kernel or anything its defo the phone as i tried another on both machines and that works fine cheers mig wattsy
Just looked at logcat at got the following:
Code:
D/BatteryService( 2245): CHARGER :: mBatteryStatus = 2
D/NotificationService( 2245): enqueueNotification :: notification.defaults = 2, Notification.DEFAULT_SOUND = 1, notification.sound = null
I/StatusBarPolicy( 2245): BAT. status:2 health:2
D/CorePlayerService( 3248): mSystemReceiver:onReceive(action=android.intent.action.BATTERY_CHANGED) is called
D/WifiService( 2245): ACTION_BATTERY_CHANGED pluggedType: 1
I/WifiService( 2245): handleMessage: MESSAGE_ENABLE_WIFI
I/WifiService( 2245): handleMessage: MESSAGE_START_WIFI
E/Setting ( 2945): Intent Action android.intent.action.ACTION_POWER_CONNECTED
E/Setting ( 2945): Battery charging. plugType = 1
E/Setting ( 2945): AC charge
I/ActivityManager( 2245): Start proc com.android.MtpApplication for broadcast com.android.MtpApplication/.MtpReceiver: pid=6175 uid=10073 gids={3003, 1015, 3002, 3001}
I/Zygote ( 6175): Zygote: pid 6175 has INTERNET permission, then set capability for CAP_NET_RAW(13)
I/dalvikvm( 6175): Debugger thread not active, ignoring DDM send (t=0x41504e4d l=38)
I/dalvikvm( 6175): Debugger thread not active, ignoring DDM send (t=0x41504e4d l=56)
E/MTPRx ( 6175): In MtpReceiverandroid.intent.action.ACTION_POWER_CONNECTED
E/MTPRX ( 6175): Battery charging. plugType = 1
E/MTPRx ( 6175): Not of USB charging. Dont lauch MTP APP
W/PowerManagerService( 2245): Timer 0x3->0x3|0x0
I/System.out( 2645): interface name: null
I/SISODRM ( 2645): OMADRMManager : IsDrmFileByExt : in
I/SISODRM ( 2645): OMADRMManager : IsDrmFileByExt : out
I/SISODRM ( 2645): OMADRMManager : IsDrmFileByExt : in
I/SISODRM ( 2645): OMADRMManager : IsDrmFileByExt : out
I/SISODRM ( 2645): OMADRMManager : IsDrmFileByExt : in
I/SISODRM ( 2645): OMADRMManager : IsDrmFileByExt : out
D/dalvikvm( 2645): GC freed 2182 objects / 600816 bytes in 180ms
I/System.out( 2645): interface name: null
I/SISODRM ( 2645): OMADRMManager : IsDrmFileByExt : in
I/SISODRM ( 2645): OMADRMManager : IsDrmFileByExt : out
I/SISODRM ( 2645): OMADRMManager : IsDrmFileByExt : in
I/SISODRM ( 2645): OMADRMManager : IsDrmFileByExt : out
I/SISODRM ( 2645): OMADRMManager : IsDrmFileByExt : in
I/SISODRM ( 2645): OMADRMManager : IsDrmFileByExt : out
D/dalvikvm( 2593): GC freed 401 objects / 21344 bytes in 189ms
I/System.out( 2645): interface name: null
I/SISODRM ( 2645): OMADRMManager : IsDrmFileByExt : in
I/SISODRM ( 2645): OMADRMManager : IsDrmFileByExt : out
D/PowerManagerService( 2245): lightSensorChangedLocked 6
I/StatusBarPolicy( 2245): BAT. status:2 health:2
D/CorePlayerService( 3248): mSystemReceiver:onReceive(action=android.intent.action.BATTERY_CHANGED) is called
D/WifiService( 2245): ACTION_BATTERY_CHANGED pluggedType: 1
Not entirely sure what it all means but from what I can gather, it seems the USB interface can't get a response?
so mig what do you reckon it is then mate weird as hell am i needing to send the fone back its intermittent for me for a while now its not having any usb but charging cheers wattsy
ps have you manged to solve ur phone connecting yet let me know mate thanks for ur time
wattsy1612 said:
so mig what do you reckon it is then mate weird as hell am i needing to send the fone back its intermittent for me for a while now its not having any usb but charging cheers wattsy
ps have you manged to solve ur phone connecting yet let me know mate thanks for ur time
Click to expand...
Click to collapse
I think the USB is kaplunked. On trying the AC adapter I get the exact same response through logcat and the plug-type doesn't change. Also, this message concerns me slightly:
Code:
E/MTPRx ( 6175): Not of USB charging. Dont lauch MTP APP
This is saying that the cable plugged in is not USB? Thinking it is on AC?
It could be a firmware issue but I would hazard a guess that the hardware is faulty and reporting the wrong the thing to android.
I'll be taking my phone for repair tomorrow,
Suprised nobody else has got any answers regarding this
Cheers,
MiG
will take mine over too but dont think i should untill froyo is released does me having froyo void my warrenty? if it does then i will wait till its released and send it then if i take it too my local service centre how long will they have my fone for do you think will have to wait as cant flash eclair back without usb lol cheers wattsy1612
Can any of u guys create a script to re-enable the usb interface cheers wattsy
*update so called samsung and was told that this 100% a hardware issue they told me to take it straight to my local service centre for an instant replacement will give another update when i return cheers wattsy
Same problem
I am having the same problem with persistent unknown device. i was also thinking of taking it back to samsung service station. i did once, but the person told me that this is due to humidity. i seriously doubt the intelligence of these people. have you received your sgs back? and is it working?
mine has gone for repair managed to find a way to connect usb and flash with odin the only way to fix this is to send it off will let you know when mines back also mig managed to get his working he just deleted everything off of the internal phone memory that he didnt need restarted the f/s and reboot his was working mine was the same but it suddenly just packed up if i was you id just send it off cheers wattsy
I will be waiting for the news. i was also thinking of the same. in the mean time some food for thought, whenever i connect the device to PC, Settings>About phone>Status shows Charging by AC adopter. whenever the phone is connected to AC adapter, Settings>About phone>Status shown charging through USB. Any coments?
my problem was solved by pulling the phones usb connector slightly towards the screen side of the phone. now it is connecting seamlessly
Hi !
That's the topic I've been looking for !
Here's my story: I've got the genuine Samsung usb cable, and when I plug it between my phone and my computer, I can either choose to mount my phone as a mass storage device, or in KIES mode or .... Usual behaviour ...
In the mean time, the phone gets charged via USB power.
I bought 2 very cheap made in China data usb cable.
None of them let me enter the usb data mode. I mean, both cables can charge my phone, but I can't connect my phone to my computer for data exchange.
So I decided to dismantle one of my cheap data cable. Wiring seems correct, and exactly the same as my genuine Samasung data cable.
Then I decided to slighlty rework the micro usb plug on my cheap data cable with a sharp cutter.
And I discovered something interesting: depending on how I insert the cable in my phone, I sometimes get access to the data exchange mode.
For instance, if I fully insert the cable straight into the phone, it only charges the phone.
But if I partly insert the cable, I the get access to the data mode. And if I want to enter the mass storage mode, I then have to completely insert the cable into the phone for the phone to be properly detected by the computer.
Odd isn't it ?
Does anyone could explain me how the phone detects if it is connected to a charger or to a real data usb cable ?
I've been reading a bit of Android documentation but didn't find anything.
developer.android.com/reference/android/os/BatteryManager.html#BatteryManager%28%29
By the way, when I run logcat from my phone, I get different kinds of message, depending on how I insert my cable:
D/WifiService( 2707): ACTION_BATTERY_CHANGED pluggedType: 1
Or
D/WifiService( 2707): ACTION_BATTERY_CHANGED pluggedType: 2
As far as I understood, 1 means AC plugged and 2 means USB plugged
my USB Port is a little bit bricked , too.
Kies and Windows just detects the phone after rebooting the phone. after a while mtp-app is beeing launched, but windows don't recognize the phone...
hope the next firmware update will work !
I have a Samsung GT-I9000B and I cant use it using USB.
I have 2 usb cables, I am able to find my friends phones.
Now I cant change rom cause odin cant find it too.
Alog cat shows:
E/MTPRx ( 4020 ) Battery charging. plugType = 1
E/MTPRx ( 4020 ) Not of USB charging. DOnt launch MTP APP
Any suggestion?
sektorNBA said:
I have a Samsung GT-I9000B and I cant use it using USB.
I have 2 usb cables, I am able to find my friends phones.
Now I cant change rom cause odin cant find it too. Any suggestion?
Click to expand...
Click to collapse
Maybe this might help http://forum.xda-developers.com/showpost.php?p=27205737&postcount=4571
MTP device fix http://www.4shared.com/office/ewdIWux2/usb-connection-issues-mtp-devi.html
Hello,
I've googled a lot for "dead camera" and found only that there are cases when phone replacement only helped.
Here is what I got from dmesg on phone restart:
Code:
<3>[ 18.292510] starting read retry policy count:17
<3>[ 18.552215] qup_i2c qup_i2c.4: Transaction timed out
<3>[ 18.572235] s5k3h1gx_i2c_rxdata failed!
<3>[ 18.572326] s5k3h1gx_i2c_read 0x0 failed!
<3>[ 18.572418] starting read retry policy count:18
<3>[ 18.832214] qup_i2c qup_i2c.4: Transaction timed out
<3>[ 18.852233] s5k3h1gx_i2c_rxdata failed!
<3>[ 18.852416] s5k3h1gx_i2c_read 0x0 failed!
<3>[ 18.852508] starting read retry policy count:19
<3>[ 18.852630] read sensor id fail
<6>[ 18.852813] [Camera] gpio_request(35, "s5k3h1gx")
<6>[ 18.872222] s5k3h1gx_vreg_disable camera vreg off
<6>[ 18.872314] sensor_vreg_off camera vreg off
<6>[ 18.872772] sensor_power_disable("wlan2") == 0
<6>[ 18.873077] sensor_power_disable("lvsw1") == 0
<6>[ 18.873474] sensor_power_disable("gp6") == 0
<6>[ 18.873779] sensor_power_disable("gp4") == 0
<3>[ 18.873901] SENSOR PROBE FAILS!
<6>[ 18.874084] config_camera_off_gpios
<3>[ 18.875122] [CAM]msm_sync_init: failed to initialize s5k3h1gx
<4>[ 18.875213] msm_camera_s5k3h1gx: probe of msm_camera_s5k3h1gx.0 failed with error -5
Does anybody here know if this can be resolved programmatically somehow, or this is completely hardware problem and the phone should be returned back to the shop (this would take a lot of time, though, this is why I'm asking here).
I have tried hardware reset - didn't help.
Thanks beforehand.
I was seeing the same messages in the log on my HTC Glacier, and likely is a hardware failure. Mine just stopped working yesterday -- all camera-related apps would either time out or force close. Tmobile is replacing my phone for me.