I just flashed Overcome 3.1 on the my ATT Galaxy Tab 7. The rom is super smooth. Everything appeared to go flawlessly however once completed I was unable to establish a proper data connection.
Its shows 4 bars and says connected to ATT as the "Network" under the Status menu. However the "Mobile Network State" is listed as disconnected.
If I go into the Mobile Network Settings. Under Network Operators ATT is listed under Auto Connect and if I rescan it accepts the choice and then says Registered on Network.
I cannot browse the internet. I called ATT and they were able to send me a SMS so there is some sort of connection. We could not troubleshoot any further as there systems are down.
I did a vanilla Overcome Install. Is there a post install step that I need to do? I seem to remember a similar issue with my Dell Streak that involved modifying my APN settings. Here are the APN settings for the device. (these are the Overcome defaults i believe)
Name: ATT
APN: wap.cingular
Proxy: leave blank
Port: leave blank
User name: [email protected]
Password: blank
Sever: leave blank (Will read: <not set>)
MMSC: http://mmsc.cingular.com
MMS proxy: wireless.cingular.com
MMS port: 80
MCC: 310
MNC: 410
Authentication type: none
APN type: internet+mms
I read this on this forum somewhere, and has always worked for me when reflashing. This is ONLY for the Pay as You Go data service to my knowledge. Your mileage may vary.
I changed my APN to the following EXACTLY:
Name: Broadband
APN: Broadband
Proxy: leave blank
Port: leave blank
User name: blank
Password: blank
Sever: leave blank (Will read: <not set>)
MMSC: not set (delete whats in here)
MMS proxy: not set (delete whats in here)
MMS port: not set (delete whats in here)
MCC: 310
MNC: 410
Authentication type: none
APN type: internet
I always get a connection this way. No MMS, but I don't use it anyway, that's what my phone is for.
The "broadband" apn is only for the sim card that came with a stock at&t tab, and not for the sim cards we all took from other phones.
For the former phone sim cards, wap.cingular or isp.cingular apn's.
The setting should be to "auto".
You didn't mention your modem - baseband.
rangercaptain said:
You didn't mention your modem - baseband.
Click to expand...
Click to collapse
Baseband: I9000UGJK3
Modem: I am not sure how to verify this on the device (Im an n00b). I did follow the wonderful guide on Team Overcome and it recommended using "JK3 Modem" During the install. I would assume this is what I am using. How can I verify this?
PS. I wapped in my phone SIM card and everything works just fine. I can even make phone calls!
Droid2Froyo said:
I read this on this forum somewhere, and has always worked for me when reflashing. This is ONLY for the Pay as You Go data service to my knowledge. Your mileage may vary.
I changed my APN to the following EXACTLY:
Name: Broadband
APN: Broadband
Proxy: leave blank
Port: leave blank
User name: blank
Password: blank
Sever: leave blank (Will read: <not set>)
MMSC: not set (delete whats in here)
MMS proxy: not set (delete whats in here)
MMS port: not set (delete whats in here)
MCC: 310
MNC: 410
Authentication type: none
APN type: internet
I always get a connection this way. No MMS, but I don't use it anyway, that's what my phone is for.
Click to expand...
Click to collapse
This did the trick! I used these settings with the replacement SIM card they gave me at the ATT store...
Good job. The baseband is the modem, so you are using JK3 - that's the best choice for you.
Downloading the AT&T Widget seemed to of helped: http://forum.xda-developers.com/showthread.php?t=898688
Related
My Captivate can read the SIM Card, but I can't connect to the AT&T service.
I go to Settings > Wireless & Network > Mobile Netoworks > Network Operators > And select AT&T, but it says "Your SIM card does not allow a connection to this network."
On Perception 9.5, When I do the same thing, It says "Unable to connect. Try again later."
I flashed other ROMs and they all do the same thing.
Help?
Are you using an AT&T sim that has a data plan enabled?
ua549 said:
Are you using an AT&T sim that has a data plan enabled?
Click to expand...
Click to collapse
Yep. 3G, Calling and SMS was all working before.
Have you manually checked the apn settings?
newter55 said:
Have you manually checked the apn settings?
Click to expand...
Click to collapse
Yeah.
Name: ATT WAP
APN: wap.cingular
Proxy: wireless.cingular.com
Port: 80
User name: Not set
Password: Not set
Server: Not set
MMSC: http://mmsc.cingular.com
MMS proxy: wireless.cingular.com
MMS port: 80
MCC: 310
MNC 410
Authentication type: None
APN type: Internet + SMS
Rikusaki said:
Yeah.
Name: ATT WAP
APN: wap.cingular
Proxy: wireless.cingular.com
Port: 80
User name: Not set
Password: Not set
Server: Not set
MMSC: http://mmsc.cingular.com
MMS proxy: wireless.cingular.com
MMS port: 80
MCC: 310
MNC 410
Authentication type: None
APN type: Internet + SMS
Click to expand...
Click to collapse
Did you flash a new rom recently? Maybe the modem isn't playing nice.
If nothing else, go get a new sim from the local store and see if that fixes it.
DarrellRaines said:
Did you flash a new rom recently? Maybe the modem isn't playing nice.
If nothing else, go get a new sim from the local store and see if that fixes it.
Click to expand...
Click to collapse
Yeah, I flashed multiple roms (Perception, Doc's, Darky, GingerClone...). They all do the same thing.
I guess I will just head over to AT&T and get a new SIM.
Hello,
I have a GT-P1000 that I am trying to connect to the Fido network's 3G/H 850/1900 without much success.
I am currently running the Overcome Stock Safe firmware and have gone through a number of modems trying to achieve the networks full potential.
So far all I can get is G/Edge.... would be KILLER to get it running on 3G/H!!!
I am curious if there any other Fido customers out there that have tried to get the Galaxy tab up and running on the Fido network.
Thanks
Someone else was complaining about the same problem. I sent him through everything I could think of and it's a no-go. The euro tab doesn't like the North America 1900mhz 3g band.
Hmmm..
Is it a firmware issue or modem issue? Or are you saying I have a TAB that is pretty much neutered in North America when it comes to 3G?
Thanks for the reply.
B.B.
He flashed every modem - so it's the chip.
http://forum.xda-developers.com/showthread.php?t=1172540
need help with my p1000 on at&t
sikstiks said:
Hello,
I have a GT-P1000 that I am trying to connect to the Fido network's 3G/H 850/1900 without much success.
I am currently running the Overcome Stock Safe firmware and have gone through a number of modems trying to achieve the networks full potential.
So far all I can get is G/Edge.... would be KILLER to get it running on 3G/H!!!
I am curious if there any other Fido customers out there that have tried to get the Galaxy tab up and running on the Fido network.
Thanks
Click to expand...
Click to collapse
What are your APN values?
ecb5 said:
What are your APN values?
Click to expand...
Click to collapse
I have tried both of these settings:
NAME: Fido Internet
APN: Internet.fido.ca
PROXY: 205.151.11.11
PORT: 8080
USER NAME & PASSWORD: fido
SERVER: (not set)
MMSC: http://mms.fido.ca
MMS PROXY: 205.151.11.13
MMS PORT: (not set)
MCC: 302
MNC: 370
AUTHENTICATION TYPE: (none)
APN Type: Internet + mms
And:
NAME: Fido Internet
APN: Internet.fido.ca
PROXY: (not set)
PORT: (not set)
USER NAME & PASSWORD: fido
SERVER: (not set)
MMSC: (not set)
MMS PROXY: (not set)
MMS PORT: (not set)
MCC: 302
MNC: 370
AUTHENTICATION TYPE: (none)
APN Type: Internet
Sorry i had forgotten about your problem.
I will look into my tab tonight and will let you know of my settings.
WHAT i remember is that i have 2 or 3 different apns
sikstiks said:
I have tried both of these settings:
NAME: Fido Internet
APN: Internet.fido.ca
PROXY: 205.151.11.11
PORT: 8080
USER NAME & PASSWORD: fido
SERVER: (not set)
MMSC: http://mms.fido.ca
MMS PROXY: 205.151.11.13
MMS PORT: (not set)
MCC: 302
MNC: 370
AUTHENTICATION TYPE: (none)
APN Type: Internet + mms
And:
NAME: Fido Internet
APN: Internet.fido.ca
PROXY: (not set)
PORT: (not set)
USER NAME & PASSWORD: fido
SERVER: (not set)
MMSC: (not set)
MMS PROXY: (not set)
MMS PORT: (not set)
MCC: 302
MNC: 370
AUTHENTICATION TYPE: (none)
APN Type: Internet
Click to expand...
Click to collapse
i have one for general, one for internet and one for tethering.
NAME: Fido Default
APN: fido-core-appl1.apn
USER NAME & PASSWORD: fido
MMSC: http://mms.fido.ca
MMS PROXY: 205.151.11.13
MMS PORT: 80
MCC: 302
MNC: 370
AUTHENTICATION TYPE: default,supl,mms
APN Type: Internet + mms
apn protocol: IPv4
NAME: Fido Internet
APN: Internet.fido.ca
PROXY: (not set)
PORT: (not set)
USER NAME & PASSWORD: fido
SERVER: (not set)
MMSC: (not set)
MMS PROXY: (not set)
MMS PORT: (not set)
MCC: 302
MNC: 370
AUTHENTICATION TYPE:
APN Type: default,supl
apn protocol: IPv4
its the first one that is choosed between the three.
Hope this helps
Thank you very much,
It has not made a difference unfortunately... but still digging for a solution.
Much appreciated.
ecb5 said:
Sorry i had forgotten about your problem.
I will look into my tab tonight and will let you know of my settings.
WHAT i remember is that i have 2 or 3 different apns
Click to expand...
Click to collapse
May I ask which modem you are using?
sikstiks said:
May I ask which modem you are using?
Click to expand...
Click to collapse
i can't remember how to check that info... the dial pad?
P1000nubjp3
Thank you
I am very happy to post that I have resolved my issue regarding the lack of connectivity in my region.
It was in fact a modem issue.
I found the solution on this page
http://forum.xda-developers.com/showthread.php?t=847273
I followed the instructions on that thread to test the modem under the ROM prescribed there... it worked on all available bands in my region, and proceeded to use just the modem along with the overcome ROM, and again success.
I am attaching the modem for any other Canadian Fido users encountering this problem. Hope it I can pay it forward.
Thank you again for all you help.
Great support structure here at XDA!!
That's the recommended modem for North America, included in the Team Overcome download. Your baseband will say i9000JK3.
How did you miss that modem when you flashed all the modems in the stickie?
That is the kicker,
I did in fact try the JK3 modem that came with the Overcome download, and it did not function. At all.
I am/was left wondering this myself.
This modem specifically, this time... after going through the process of reverting back to 2.2 from the url in my post...
Worked.
I, in no way claim to understand why. LOL!!
Just thanking for all the great help.
rangercaptain said:
Your baseband will say i9000JK3.
Click to expand...
Click to collapse
The baseband reads:
I9000UGJK3
That's funny. Now if I could remember where I left the car keys . . .
sikstiks said:
I am very happy to post that I have resolved my issue regarding the lack of connectivity in my region.
It was in fact a modem issue.
I found the solution on this page
http://forum.xda-developers.com/showthread.php?t=847273
I followed the instructions on that thread to test the modem under the ROM prescribed there... it worked on all available bands in my region, and proceeded to use just the modem along with the overcome ROM, and again success.
I am attaching the modem for any other Canadian Fido users encountering this problem. Hope it I can pay it forward.
Thank you again for all you help.
Great support structure here at XDA!!
Click to expand...
Click to collapse
Sorry i couldn't help you more...but glad it is resolved.
Hello All,
I have a Samsung Galaxy S I9000 phone. I am currently on AT&T. I needed to know the APN settings for it. For the first time i see that at $50 GoPhone has included unlimited data now. So i was hoping to make use of it. I have googled and found out many different settings for it. Some same, some with minor changes. But none of them work. I put I know i wont be able to get LTE. But need the normal settings to start using data service.
I currently have this:
Name: AT&T
APN: wap.cingular
Proxy: blank
Port: blank
Username:[email protected]
Password:CINGULAR1
Server: blank
MMSC: http://mmsc.cingular.com
MMS Proxy: wireless.cingular.com
MMS Port: 80
MCC:310
MNC:410
APN Type: blank
All I see "H" symbol on top appear.
My employer provides me with cell service and to date hasn't cared if I use the Blackberry they provide or put the AT&T SIM in a personal phone. Provided I don't hassle the phone support staff with problems I created, of course. I've used the same SIM in 3 different phones over the past year and haven't had a single issue. I just got a used Atrix HD and discovered that it uses a micro-SIM instead of a regular size. I used a template and cut it down to size (and I think I did it correctly). I put it in the AHD and the SIM is recognized as AT&T but I cannot get data service. On first use with the bone stock ROM, I got a text message and was able to reply to it. Because I have no intention of staying stock, over the past two hours I've done the following:
Rooted
Unlocked bootloader
Installed the ATT-US_BuildA ROM
Wiped that and installed CM10.1 nightly from 05/16
I've not been able to get any data service and now the status is 'In service' for Service state, 'Disconnected' for Mobile network state, and 'Unknown' for Phone Number. Even after cutting down the SIM, I can put it back in my Blackberry and voice and data work just fine. Thus I know the SIM is healthy. Questions:
Is the mini-card slot in the AHD that finicky that a mm difference in card size will dork it up?
The SIM is several years old now. Is it obsolete for the AHD (not withstanding size)?
Are there any settings in the phone that I'm overlooking? The eBay seller was in the US but I do not know the original location of the phone.
Thanks for any advice you can provide. Unfortunately, I can't take it to an AT&T store because the account is my employer's. And my employer really doesn't want to deal with my issue that only exists because they were nice and turned a blind eye to me.
maybe you need to change your APN settings go to settings and under wireless and networks select "more...."
then mobile networks and then access point names select the menu option in the top right and select "New APN" and enter the info below
Name: Cingular 410
APN: wap.cingular
Proxy: Blank
Port: Blank
Username: [email protected]
Password: CINGULAR1
Server: cingulargprs.com
MMSC: http://mms.cingular.com
MMS Proxy: wireless.cingular.com
MMS Port: Blank
MCC: 310
MNC: 410
Authentication type: Blank
APN Type: default,supl,mms
APN protocol: leave as is
Bearer: leave as is
For 4G
Name: AT&T HSPA+
APN: phone
Proxy: Blank
Port: Blank
Username: blank
Password: blank
Server: blank
MMSC: http://mmsc.mobile.att.net
MMS Proxy: proxy.mobile.att.net
MMS Port: 80
MCC: 310
MNC: 410
Authentication type: Blank
APN Type: default,supl,mms,hipri
APN protocol: leave as is
Bearer: leave as is
Thank you!!!!!!!!!
The 4G settings were successful and I'm good to go. I'm very grateful and thanks again!
No problem glad to hear it worked.
Just came from the rezound, upgraded to HTC one. The phone is only a week old, all stock, the data doesn't seem to be working right. Always getting connection timeout or just sits there, arrows on top don't even light up. I've gone thru 4 gigs in less than a week and I haven't done anything. Everything is unsynced and background data is restricted. Called Verizon and got some girl who wouldn't do anything but have me take out the SIM card. Any fix or any suggestions? I can also still return the phone, I'm still under the 14 day trial.
rickyjohn said:
Just came from the rezound, upgraded to HTC one. The phone is only a week old, all stock, the data doesn't seem to be working right. Always getting connection timeout or just sits there, arrows on top don't even light up. I've gone thru 4 gigs in less than a week and I haven't done anything. Everything is unsynced and background data is restricted. Called Verizon and got some girl who wouldn't do anything but have me take out the SIM card. Any fix or any suggestions? I can also still return the phone, I'm still under the 14 day trial.
Click to expand...
Click to collapse
check your apn settings:
settings ---> mobile data ---> access point names
check that your apn is correctly configured for verizon
Name: Verizon
APN: internet or vzwinternet
Proxy: blank
Port: blank
Username: blank
Password: blank
Server: blank
MMSC: http://mms.vtext.com/servlets/mms
MMS Proxy: blank
MMS Port: 80
MCC: 310
MNC: 012
Authent. type: not set
APN Type: internet + mms
You could try installing something like 3g watchdog, or my data manager. It will tell you which apps are downloading/uploading, and how much they have used aswel.
Sent from my HTC One using Tapatalk
Name: internet
APN: vzwinternet
Proxy: not set
Port: not set
Username: not set
Password: not set
Server: not set
Mmsc: its ok!
Mms proxy: not set
Mms port: not set
Mms protocol: wap 2.0
Mcc: 311
Mnc: 480
Authentication type: not set
Apn type: not set
Apn enable/disable: enabled
Bearer: unspecified
I'm guessing it's not right. Stock 4.4.2 - 3.11.605.1