Related
I have an BA XDA2s, and was attempting to upgrade ROM to latest WM5 version. Got as far as going into bootloader mode, and running BAupgradeUT. Mid update the programe said it had lost connection to phone (pretty sure i didnt accidentally disconnect it). My xda is now stuck with a blank screen with nothing except v2.08 at the botttom, and either USB or Serial at the top (depending on weather on cradle or not). I tried running BAupgradeUT again - but it has a connection error before it even starts now.
During the update my computer said that it had detected new hardware, and started trying to install drivers for it, but got stuck when it couldnt find "wceusbsh.sys" file in my windows dir. (i forget which im afraid ...)
im perfectly happy to accept any solution - including ones that involve restoring the retail rom - i just want my phone back. can anyone help me, or am i royally screwed? thanks in advance...........
****...I fu**ed things up 2:S What to do now?
i think ive solved mine - if your having the same problem as me, i can give ya a hand... otherwise - im probably not the best person to talk to ......
well...tell me please, because i know what i did wrong...no extrom on my sd card...
right well - im pretty new at this, so bear with me
basically i eventually solved the problem by locating the file that it couldnt find, and when i had located that file, it had no problems communicating with the phone. so i ran the update again - and it worked fine...
afaik - the screen blank screen with v2.08 is just the normal screen while it waits for the rom to be uploaded.....
hth..... if not then its out of my leauge
ok..i'll try again:S
Maybe some of you are already aware of this procedure, maybe not.
Anyway, it worked for me and I decided to share how to do it. Simple.
This procedure should only be used in case you really need enter into a bootloader mode and all other ways to do it has failed! Hold Camera button is one of these I am mentioning.
My Wizard was almost bricked at that time and after I speak with an I-mate technical guy, I got the following:
1. Make sure your i-mate™ K-JAM is not Connected to the PC and remove the dummy card or SD/MMC card
2. On your Desktop PC, open Microsoft ActiveSync, then go to File >Connection Settings >Remove the Selection from “Allow USB Connection with this desktop computer”
3. Reconnect your i-mate K-JAM to the Desktop PC using the USB Cradle and the Charger MUST be Connected to the Cradle (Don’t use the IrDA or Bluetooth for the Upgrade)
4. Run the Upgrade again and it will work fine without any problems.
While upgrading, the ActiveSync program will not go on, however the upgrade is running.
Hope it helps!
this realy worked for my (ex)bricked dutch tmobile mda vario !!!!
tip: REALY make shure that there is no wcescomm.exe running all the time and realy remove the sd card else is nogo
btw: my wizard is CID locked! and works like a charm
Thanks buddy!
I'm happy that worked for ya!
Take care!
I'm having a problem
The power went out as I was upgrading my Wizard (Cingular) so now it just turns on at the boatloader screen. I've tried running updates while it was in this screen (it did show the "USB" in the white bar) but most of the time it tells me there is a connection error. Even if I kill Activesync, I notice that when I run the update utility it still runs Activesync. I've tried disabling the USB connection but still get the connection error.
The only time I haven't gotten the connection error was twice it asked me to update but then told me I had the wrong file. This only happened when I tried "upgrading" to 1.05 as I was trying to start again. After it tells me that if I try running it again it gives me the connection error.
Any ideas?
Hi!
Have you already flashed your device once?
Which ipl/spl do you have?
I had problems over 1.05 ROM in the beggining.
If you stuck on bootloader mode, that's a good signal your device is not bricked.
I'd recommend you to disable activesync as you did and reflash it again! Check also if your device is CID unlocked! Search for a thread in the xda developers root.
Try to upgrade to ipl/spl 2.26 first and later to others you want.
Regarding the old file error...can be related to a missing file called enterbootloader.exe.
Hope it works for ya!
Take care
Ironman273 said:
I'm having a problem
The power went out as I was upgrading my Wizard (Cingular) so now it just turns on at the boatloader screen. I've tried running updates while it was in this screen (it did show the "USB" in the white bar) but most of the time it tells me there is a connection error. Even if I kill Activesync, I notice that when I run the update utility it still runs Activesync. I've tried disabling the USB connection but still get the connection error.
The only time I haven't gotten the connection error was twice it asked me to update but then told me I had the wrong file. This only happened when I tried "upgrading" to 1.05 as I was trying to start again. After it tells me that if I try running it again it gives me the connection error.
Any ideas?
Click to expand...
Click to collapse
My device is unlocked as I've been trying different ROMs as of late. I had gone back to the Cingular 2.25 ROM for a couple days to sort some things out and was going to flash Farias AKu 3.3 when my power problems happened. My Current IPL/SPL is 2.25
I've tried flashing the TMobile 2.26 but keep getting connection errors. In fact, I've tried flashing with every ROM I have pdviet 3 and 4, CIngular 2.25, TMobile 2.26 and Custom 1.05. Everything (except twice in the custom) gives me connection errors.
Any other trick I can try?
BTW, I used to live in Sao Paulo years ago...
Edit: OK, so I tried the 2.26 TMobile ROM after I typed this and it worked!! I'm back up but I was having trouble with that ROM beause of some incompatibilities with Cingular. I'll go back to Cingular's ROM and play it safe for now.
I believe part of my problem was I kept trying different updates one after the other. Now that I think back, the 2 times I got the update to almost work was after I turned off the device and turned it on again, which is what I did this time around also.
I had the same problems as mentioned by Ironman before. I followed the steps and with a few slight changes, I managed as well to "unbrick" my wiz. THANKS A LOT for the great step by step manual!!!
Still I wanted to know WHY i bricked my device:
I was trying to upgrade to the underground WM6 ROM. I got the same situation as ironman:
Quote:
The power went out as I was upgrading my Wizard (Cingular) so now it just turns on at the boatloader screen. I've tried running updates while it was in this screen (it did show the "USB" in the white bar) but most of the time it tells me there is a connection error. Even if I kill Activesync, I notice that when I run the update utility it still runs Activesync. I've tried disabling the USB connection but still get the connection error.
The only time I haven't gotten the connection error was twice it asked me to update but then told me I had the wrong file. This only happened when I tried "upgrading" to 1.05 as I was trying to start again. After it tells me that if I try running it again it gives me the connection error.
Unquote
I then followed the instructions by epimazzo as written above. I also tried the T-Mobile ROM 2.26 which was not working for me. PANIC!!!! Error messag was that I had the wrong Vendor ID. THerefore no upgrade to TMob 2.26 was possible. I tried it then my original qtek ROM in my language and see it worked!!! This IMHO means that I did not put the device in a proper IPL1.xx and SPL 1.xx status which is required for a clean system in irder to unlock it! So if it is bricked, try your native AKU2 ROM and make sure you unlocked it properly. Maybe you have to run the 1.05 ROM for a second time after the unlocking.
I hope this helps you guys.
Sounds great to hear that!
I had play around with pdaviet3, underground and another ROM just today without any problems at all. I don't think that this is the case. Now you get your device back to normal, try to reflash it again. Hope it works this time!
BTW,...São Paulo is a nice city. Thanks! Let me know if you decide to come here!
Take care
Ironman273 said:
My device is unlocked as I've been trying different ROMs as of late. I had gone back to the Cingular 2.25 ROM for a couple days to sort some things out and was going to flash Farias AKu 3.3 when my power problems happened. My Current IPL/SPL is 2.25
I've tried flashing the TMobile 2.26 but keep getting connection errors. In fact, I've tried flashing with every ROM I have pdviet 3 and 4, CIngular 2.25, TMobile 2.26 and Custom 1.05. Everything (except twice in the custom) gives me connection errors.
Any other trick I can try?
BTW, I used to live in Sao Paulo years ago...
Edit: OK, so I tried the 2.26 TMobile ROM after I typed this and it worked!! I'm back up but I was having trouble with that ROM beause of some incompatibilities with Cingular. I'll go back to Cingular's ROM and play it safe for now.
I believe part of my problem was I kept trying different updates one after the other. Now that I think back, the 2 times I got the update to almost work was after I turned off the device and turned it on again, which is what I did this time around also.
Click to expand...
Click to collapse
It seems you got the idea!
You did the right thing! Sometimes, use the official ROM can solve many issues out there!
Keep walking!
enlite_de said:
I had the same problems as mentioned by Ironman before. I followed the steps and with a few slight changes, I managed as well to "unbrick" my wiz. THANKS A LOT for the great step by step manual!!!
Still I wanted to know WHY i bricked my device:
I was trying to upgrade to the underground WM6 ROM. I got the same situation as ironman:
Quote:
The power went out as I was upgrading my Wizard (Cingular) so now it just turns on at the boatloader screen. I've tried running updates while it was in this screen (it did show the "USB" in the white bar) but most of the time it tells me there is a connection error. Even if I kill Activesync, I notice that when I run the update utility it still runs Activesync. I've tried disabling the USB connection but still get the connection error.
The only time I haven't gotten the connection error was twice it asked me to update but then told me I had the wrong file. This only happened when I tried "upgrading" to 1.05 as I was trying to start again. After it tells me that if I try running it again it gives me the connection error.
Unquote
I then followed the instructions by epimazzo as written above. I also tried the T-Mobile ROM 2.26 which was not working for me. PANIC!!!! Error messag was that I had the wrong Vendor ID. THerefore no upgrade to TMob 2.26 was possible. I tried it then my original qtek ROM in my language and see it worked!!! This IMHO means that I did not put the device in a proper IPL1.xx and SPL 1.xx status which is required for a clean system in irder to unlock it! So if it is bricked, try your native AKU2 ROM and make sure you unlocked it properly. Maybe you have to run the 1.05 ROM for a second time after the unlocking.
I hope this helps you guys.
Click to expand...
Click to collapse
Excellent post. I messed up with my own cooked ROM and could only get the bootloader screen. Tried the tips here - didn't work first time but I pulled the battery from the KJAM to reset it rather than using the reset button and it worked fine.
In my opinion this thread is so helpful to people who brick their device, it should go "sticky". Mods anything you can do about it?
Thanks buddy! I really appreciate!
We survive here over tips like that!
jt_armstrong said:
Excellent post. I messed up with my own cooked ROM and could only get the bootloader screen. Tried the tips here - didn't work first time but I pulled the battery from the KJAM to reset it rather than using the reset button and it worked fine.
Click to expand...
Click to collapse
Help me similar problem
I upgraded Super Rom, then my Wizard run very slow and no signal (no call out and in- no network at all). And Terible thing is PC could not dectect PPC thought Active Sync. I've soft and hard reset but no use.
So I donot know where to start to re install Rom again.
Please help me....
Hi there!
It seems that you just need to enter into the bootloader mode and reflash it again!
I had similar problems and more during my brick "false" stage!
So, just try to follow my steps here and you should be fine! Once you get into bootloader mode, just use any ROM out there to reflash.
Good [email protected]
thaiphong said:
I upgraded Super Rom, then my Wizard run very slow and no signal (no call out and in- no network at all). And Terible thing is PC could not dectect PPC thought Active Sync. I've soft and hard reset but no use.
So I donot know where to start to re install Rom again.
Please help me....
Click to expand...
Click to collapse
I was about to start a EMERGENCY HELP thread, but I *think* this is the right place instead.
The "touch" of my screen went dead today. It got progressively worse over a few hours, starting with difficulty in using the phone dialer, then random incorrect stuff getting triggered by screen taps.
So I hard reset, and got no response on the fifth alignment cross, meaning 1) "Tap on the screen...; 2) center; 3) top left; 4) bottom left; 5) bottom right. In that I could not proceed with alignment, I hard reset again, and now, at the first alignment screen, i.e. "Tap on the screen...", I have no screen response at all.
I called T-mo, and they are being great about sending a replacement ASAP (and getting me a loaner in the meantime).
BUT, I am running Faria+ AKU3.3 V2... so I clearly have to flash back to T-mo 2.26. I can;t figure out how to do it though, as no matter what I do I am stuck at the first alignment screen!!
HELP!! EMERGENCY!!!
(I have three or four days to get this done, so it's not THAT urgent)
Do a search for Broken Screen. Someone (either in Wizard Upgrading or in the Wizard forum) just had a similar issue with a cracked screen. They downloaded something that allowed them to get around the welcome page.
Actually, if you are just trying to flash a new ROM, don't even mess with it. Go straight to the Boot Loader screen (see the first post of this thread). No tapping necessary until the new rom is on (and that will be the Tmobile then so you would be good.
Thanks for the quick reply. Charging up to green now, and then will try to enter bootloader and flash T-mo 2.26. Will report back.
Worked great. Back to T-mo she goes!!!
BootLoader Mode
Excellent thread but you left out one thing.....exactly how to place your device in bootloader mode.
To clear up any misunderstanding because this is very important....this is how you do it:
Perform a soft reset, when the screen goes blank hold the camera button until a multi colored screen comes up .... That's it !!!!!!
When the unit is connected, USB is displayed at the bottom left.
i went to the website
www.asia.htc.com/asia/event/WM6/index.html
and followed the on-screen instruction
what happened now is that there's an update error
i followed the step by step to recover but the thing just stuck there
now whenever i on my dopod d810,
my screen just shows the 3 color screen
and that's that
i dont know what to do!!!
help!
and this is crap
i cant seem to establish a connection AT ALL with the activesync
and whenever i want to update, it just says ERROR [286]
i did ALL the steps it suggested
- disconnect USB cable from phone
- remove the battery
- wait 3 seconds and reinstall
- when you switch on, you see 3 screens
- connect USB cable again
- resume install
and then after i resume install,
SAME PROBLEM again! ERROR [286]
its like a vicious cycle!
Just for your info
i am currently using activesync 4.5
and right now whenever i connect my usb to my phone,
the activesync doesnt seem to be able to detect the phone at all
here is the video of my several attempt to upgrade
just download it here
http://www.sendspace.com/file/ha26ws
Is there anywhere where i can download
WM6 for
- Hong Kong (ENG)?
what happened is that right now
i actually used the Aussie one and that doesnt work i think
(assuming that is the problem)
I tried the SEA one and it also doesnt seem to work
I heard that you need to use specific update
the problem is
i dont know where my dopod originate from???
is there any way to tell?
what does the tri-colour screen say?
you can check out trinityguides upgrade problem faq and see if those steps help you.. all isn't lost yet, you should be able to revive your device
let me know how it goes
the TRI screen color says
TRIN100
IPL-1.00
TRIN100
SPL-9.99.CP
ive seen the faq
doesnt help me at all
I think i might need to flash back to WM5 first
problem is,
where can i download the WM5?
Stalvros said:
I think i might need to flash back to WM5 first
problem is,
where can i download the WM5?
Click to expand...
Click to collapse
here http://wiki.xda-developers.com/index.php?pagename=Trinity_Upgrades
yeah, flashing back to wm5 is a safe bet at this point...
have you tried splxploit?
thanks~
i actually fixed this problem yesterday
i found that link that you gave
http://wiki.xda-developers.com/index.php?pagename=Trinity_Upgrades
through this
http://xman892.blogspot.com/
the strange thing is that~
the WM6 that that guy use doesnt seem to have any transcriber
while the official WM6 latest version has
It's not strange at all. The rom that you downloaded is a cooked rom. I think the cook removed any excessive stuff and so you may not find everything you want there.
Stalvros said:
the TRI screen color says
TRIN100
IPL-1.00
TRIN100
SPL-9.99.CP
ive seen the faq
doesnt help me at all
Click to expand...
Click to collapse
try this, it solve my problem just like yours!!!
http://vimafeje.com/splxploit-windows.zip
First of all i do not know where to post this. I have had a HTC wizard for over a year now. it has been working fine after cooking up wm6 and installing it for 6 months. today when i restartet the phone pulling the battery out and inserting it, the phone starts up, then the blue screen comes and shows ispl etc, then windows image shows, there it stops. i do not know what to do. It has been a while since i did pocket pc modding now, and i have forgotten all about it.
Alexander, [email protected]
Maybe something crashed the OS software.
Hope you have a system backup, or at least PIM backup using ActiveSync because what you need now is a hard reset.
Punching the reset hole (next to IR window) while holding CommManager+VoiceDial, then press "Dial" as prompted.
how do i hard reset my dash/s620?
i have tried hard reset
i have hard reset the phone. i do not have any backup in active sync. and i dont think that matters. because my phone does not connect to activesync since it does not start up. and in the three colored boot mode the phone is not detected by active sync. when i hard reset the phone it just came to the same point and freezed
If you didn't touch the ROM for long time, then it is probably a hardware failure...
lovemy318 said:
how do i hard reset my dash/s620?
Click to expand...
Click to collapse
READ YOUR PHONE MANUAL, and THIS IS NOT DASH FORUM.
hard to believe
First off, thanks for fast responses.
It cant be hardware(Not as a total theory of course) or likely not, because phone was not touched by water, shock, bumb fire or anything. it laid on my desk, worked, laid on my dask more, freezed. and it has been working for 6 months with wm6. is there anyway i can flash something into it. without activesync, but in the three colored boot mode?
Get into bootloader, plug in your usb cord and give it a minute...ON THE TRI-COLORED SCREEN do you see in the bottom corner "USB"??? If yes, you are OK. Get a stock rom such as the Tmo 2.26 and flash that. If you do not see "USB" in the bottom corner then as far as I know, you are fukd.
For more info on issues, read the linky in my siggy. There is valuable info there that may help with other ways to flash a rom.
Good luck.
i see usb
thanks, guess i am not fked then
Only problem is i have forgotten all about this now, and that i am sorry for.
But i have to ask you, as from norway wich stock rom to choose, what is stock rom, and when you say bootloader, is that an expression for the three colored screen or is that a program, that can flash in three colored screen? Thanks, i do not expect an answer on this noob questions, but i would really apreciate answers.
stock rom & bootloader
stock rom is the rom which comes with ur phone while purchasing it.. u can call it base rom..bootloader is tri-coloured screen which is bios for ppc if it gets fked then phone is bricked..next time if u cant boot up, then u can flash ur phone with the help of bootloader...
that was fast
thanks, but i do not think i have the rom that came with my mobile phone:/
and i do not know how to flash from tri colored screen, because all the files i have tried cant detect my phone.
ipl adn spl are 3.08 if that helps anything.
that was fast
is there an app you use to flash from tri colored
there is no need for any app, just connect ur phone to tri-coloured screen..u willl see usb in down left corner.. then ur phone is connected then run RUU utility.. if any problem comes i am online at hotmail... [email protected]
Can you power down? If not, remove battery for 1 seconds, the re-insert. Then press all at once the camera, comm and power buttons (or I believe you can also press the camera and soft reset. It is in the wiki explaining, as are some stock roms. Use any stock rom if you plan on flashing a cooked rom. The Tmo 2.26 is a decent stock rom, there is a 3.08 on the forum somewhere that you can also use. Get a stock rom. Get into the tri-colored bootloader. Look to see if it says usb in the bottom corner. If yes, connect your cable and using the ruu from the stock rom, flash your phone. Once a stock rom is installed follow the directions to cid/sim unlock your phone. Once unlocked, you can flash any cooked rom.
PS- I am assuming you have a G3 phone.
PPS- reading the wiki and the stickies are very helpful. Give them a try.
im sutch a noob
yeh i got same problem... i will try a hard reset but im at school... hope it fixes it... i got imate jasjam... BETTER WORK OR I WILL KILL MY BROTHER 4 STUFFING AROUND WITH MY PHONE
im sutch a noob
gah... it diddent work what do i do now????
Hey everyone. I'm tearing my hair out trying to get this sorted but I just don't know what to do!
So, when I got my X1 as everyone on here should do, was flash my X1 with the HardSPL and some custom roms, this was a few months back. Then, shock! Horror! My case went and broke, (cracked near the volume button build W44) so I sent it back to SE for repair. I sent it back reset back to defaults but left the hardspl on there.
SE sent me a brand new phone (I think... This one says under the battery build w50, but the battery says w32..) I received it today. I thought it would be my old one repaired but SE had other ideas. Booted up and have Image Version: 1.03.931.10 and HardSPL 72.000 I think I said that correctly...
Now since sending it for repair and receiving it back, their seems to be quite a few wm6.5 roms floating about, and obviously I can't use the stock software as that wouldn't be right!
Now I have tried flashing the hardspl to the phone through my Vista PC and all it keeps giving me is connection errors. I thought maybe it was already flashed so I tried flashing just a rom, and that just made the phone get stuck on loading (flash by memory card). I thought it might be Vista, so I tried doing it on my other PC (XP) and I get the same issue. This bloody thing won't flash!
I have had "Connection Problems" - "Update Errors" with different numbers. The current one being Error [260] CONNECTION.
Now I have been searching around through the hardspl thread and other places trying to find out what I need to do or how I can fix it, but everything I try doesn't make a difference. I did read some other people with recently repaired phones having the same problem and perhaps SE have put a new spl thingy-ma-jiggy on there. (Please forgive the technical jargon, I have no idea what im on about.) I have also tried the ticking/unticking advanced network functionality, but that hasn't made a difference either.
So by the end of typing this, I have little hair left. Let's hope you can all help, before I have none left!
I would appreciate ANY help! Really.
Just wanted to add, I was at first getting the phone to a loading bar when flashing, but it would stay at 0% then flag up an error on the PC. Now after the tri-colour bars, the phone just sticks on Loading...
Well just to update. I have been trying to sort this since posting. I flashed the rom to an old UK generic one, as I read in another topic people had to do that before HardSPL. Done that, and tried flashing the hardspl. Same thing, just getting connection errors.
I tried going into bootloader and running the hardspl from there. It works and the phone gets to 10% and then gives an UPDATE ERROR. The phone is now bricked, and I have to reflash the original wm rom to get it back.
Though the Tricolour screen now shows 0.52.Olinex
Any ideas?
Shameless bump for help.
very stupid situation.
i have the same situation in puncto of flashing.
i get my phone three month ago.
after hardspl i .... sorry, no hardspl ... the phone says at 0% bla bla bla
i solve the problem by consulting one night absolutly stressing again and again and again .... google ... xda ... google
than 3 thinks at one time was the solution:
0. need activesync - connect !!!!
1. SDA_ApplicationUnlock.exe for desktop pc
2. enterbootloader.exe for pocketpc (please, the right version, it exist for eten too, but we need the xpediaversion ..)
3. changing registry-entries
how to:
activesync-connect, than copy "enterbootloader.exe" to pocketpc. it must be root, not sd-card. use a pocketpc-registry-program to change these values :
HKEY_LOCAL_MACHINE\Security\Policies\Policies\00001001 = 1
HKEY_LOCAL_MACHINE\Security\Policies\Policies\00001005 = 40
HKEY_LOCAL_MACHINE\Security\Policies\Policies\00001017 = 144
HKEY_LOCAL_MACHINE \Security\Policies\Policies\0000101b = 1
if not exist than add the key.
now, start desktop-program, follow instruction EXCEPT reboot.
start "enterbootloader.exe" on pocketpc. now, you can install hardspl and the device is flashable for ever.
thats works on me, hope it could help you too.
Thanks for the reply. Not had time to try it till this morning. Ok so, after spending about an hour trying to find the correct enterbootloader.exe I finally realized, that the hardspl package includes it. *Duh!* So that was time wasted.
I changes the registry values as you said with Resco registry editor, and follower the unlock then enterbootloader.exe Start HardSPL package. Starts to install. Gets to 10% then I get
ERROR [262] : UPDATE ERROR
The rom update utility has encountered communication errors during the update process.
So im open to suggestions if anyone has any. I just can't understand why it's not working. It's not a problem with my computer or cables. I flashed the phone before I sent it for repair and I have tried doing it on two computers one with XP 32bit and one with Vista 64bit.
hmm. would u like to install a custom rom, or a stock rom?
msg me, and i hope, i can halp u.
I want to have the hardspl on there so I can flash custom roms.
If it's a case of the software/firmware/hardspl whatever you call it, has been updated by SE. How would one go about getting it flashed? Would we have to wait for an update HardSPL to be released?
U read this thread?
My first hardspl was from this thread. New X1 will come tomorrow back from SE (vibration was defect +++ some more problems with case), and i will try it again with this thread.
hope, this will help u mate.
Yeah, I have been through that thread with a fine toothcombe trying everything suggested to see if I can make it work.
When you get yours back, if you have to do anything out of the ordinary to get it to flash or can't do it. Please come and let me know in this thread. If they have updated yours like mine, and yours won't flash, at least I won't be the only one!
k, i will msg u tomorrow around 2pm.
Cheers.
In the meantime. Does anyone have any other suggestions I could try?
Bump, for some help.
now i know, what is exatcly your problem.... <--- SAME Problem
i hope, i will find a solution and msg u then. if u´ll got a solution for this prob, msg me too plz.
Solution found in this Thread!
Download this and unzip it to your device. ++ run it. It will start your X1 in Bootloader menu and say "0.52.OliNex".
Then start hardspl while X1 is in Bootloadermenu....
FINISH =)
Thanks for the reply matey. Glad you got yours sorted. Just tried what you said and I get 0% then it switches to ERROR [262] : UPDATE ERROR.
vwrmic said:
Thanks for the reply matey. Glad you got yours sorted. Just tried what you said and I get 0% then it switches to ERROR [262] : UPDATE ERROR.
Click to expand...
Click to collapse
hmmm... it works fine on my new x1. are u sure, that u start the ssplmanual on your x1 and not on your computer?
Yea, im not sure what the problem was with it. Thankfully I have it done and dusted today! Because I flashed it earlier to an older official version, and you said you got it working. I presumed you had - had yours flashed to the newest version due to it being off for repair. So I reflashed the official update and fully updated it. Then tried hardspl which didn't work. Tried with the advanced USB thing off, tried again with how you said you did it above, and Viola!
Hip hip hoorah! Thanks for the help. Can finally use me bleedin phone now!
no problem mate hf with your x1
hello,
i see smilies and yea's ...
for me to understanding (for next time or other users):
1. complete official update (if exists)
2. flashing (hardspl) without "advanced usb"
thats all?
cool.