Hey guys ,
While i was updating the phone using ode3 , the pc restarted , and the phone restarted while it was installing the os . Now the phone doesnt response to anything , no power noting at all .
I have seen some articals around but i dont know which one I should follow to try to fix that or what to do .
1- there is the usb dongle where I make a 300 ohms resistance and plug it in the usb port to force download mode . Does that apply to the phone ?
2- another way i found where i have to solider and open the phone , which i hope not the case
I am not sure what to do , but its been 3 days the phone is fully died .
Ya, if you get nothing its bricked. However, if you get any small sign of life then you would be able to get to download mode via usb jig.
Sent from my SAMSUNG-SGH-I897 using XDA App
Try the Q&A section..
Sent from my Samsung SGH-I897 using XDA Premium
aymank1985 said:
Hey guys ,
While i was updating the phone using ode3 , the pc restarted , and the phone restarted while it was installing the os . Now the phone doesnt response to anything , no power noting at all .
I have seen some articals around but i dont know which one I should follow to try to fix that or what to do .
1- there is the usb dongle where I make a 300 ohms resistance and plug it in the usb port to force download mode . Does that apply to the phone ?
2- another way i found where i have to solider and open the phone , which i hope not the case
I am not sure what to do , but its been 3 days the phone is fully died .
Click to expand...
Click to collapse
Wrong section, but try to see if you can get on download mode. (charge it a little bit)
As i said noting at all is working , not even when i plug it on to the charger.
so usb jig wont work on my case ?
very sorry for posting this in the wrong section thought i was in q/a section
LOSTLOGIC89 said:
Wrong section, but try to see if you can get on download mode. (charge it a little bit)
Click to expand...
Click to collapse
Are you saying with the usb jig?
Mine crashed the same way just the other day. I took 3 100k resistors and 2 1k resistors, put them in series then carefully touched the two ends to the two pins on inside edge of the usb female plug. It took about 15mins of trial and error then I touched them just right and it popped up with the DL screen. You say it's completely dead but if it had any charge left in the battery when it crapped out on you it should still have it now. It shouldn't drain just sitting there.
Take the battery out and try the button combos for download mode again... vol+ vol- and insert usb
Sent from my I897 using XDA App
Look in my sig. Am I bricked. It will help you find out where you are.
was the ODIN flashing bootloaders?
Might want to look in UB mod or Jtag....
Related
Im retarted wasnt paying attn, too sleepy.
I flashed the stock pit and tar from an epic onto the cappy and now it wont even turn on. Wont respond to anything.
Cant get it in to download. No life at all,Shes dead captain, kinda thing.
So it started out i was going to flash back to something other than trident/cm7.
Im bought the car dock and was going to use the kernal so the dock would actually work.
Well it was like any other flash ive done countless times.. Till odin preformed an illegal operation and then it dawned on me what i did.. It was still in download but the computer didn't recognize it any longer. So power off and try to go back to dl mode.. the phone wont respond at all. The power button does nothing.. Plugging it in does nothing..
Im pretty sure its dead, thoughts? other than the flamming for being a newb.
ninjaclipse said:
Im retarted wasnt paying attn, too sleepy.
I flashed the stock pit and tar from an epic onto the cappy and now it wont even turn on. Wont respond to anything.
Cant get it in to download. Shes dead captain, kinda thing.
So it started out i was going to flash back to something other than trident/cm7.
Im bought the car dock and was going to use the kernal so the dock would actually work.
Well it was like any other flash ive done countless times.. Till odin preformed an illegal operation and then it dawned on me what i did.. It was still in download but the computer didn't recognize it any longer. So power off and try to go back to dl mode.. the phone wont respond at all. The power button does nothing.. Plugging it in does nothing..
Im pretty sure its dead, thoughts? other than the flamming for being a newb.
Click to expand...
Click to collapse
Jig maybe? Or Jtag if you can find one.
indomikey said:
Jig maybe? Or Jtag if you can find one.
Click to expand...
Click to collapse
Well with the jig it still has to be able to turn on.. I cant get it to even do that
So i dunno.. Thats why im drawing a blank. I would think it would at the very lest be able to get in to dl mode but nothing lol
So you had the 3 button combo working before?
Have you
1 Open Odin one click or the full version to flash what you want
2 plug in the cable to your computer
3 Hold the vol up/down buttons
4 Plug in micro usb to phone?
If that doesn't work try the same process but do this.
1 Open Odin one click or the full version to flash what you want
2 Remove battery from phone
3 Plug phone to computer and hold vol up/down
4 Push battery in
Try those methods if you haven't already. If they don't work a jig might be your best option to get the phone to DL mode.
And a jig seems to work when you really think it wouldn't but try either of these methods first. I was stuck last week when my phone would not power or anything and the second method worked for me.
flashman2002 said:
So you had the 3 button combo working before?
Have you
1 Open Odin one click or the full version to flash what you want
2 plug in the cable to your computer
3 Hold the vol up/down buttons
4 Plug in micro usb to phone?
If that doesn't work try the same process but do this.
1 Open Odin one click or the full version to flash what you want
2 Remove battery from phone
3 Plug phone to computer and hold vol up/down
4 Push battery in
Try those methods if you haven't already. If they don't work a jig might be your best option to get the phone to DL mode.
And a jig seems to work when you really think it wouldn't but try either of these methods first. I was stuck last week when my phone would not power or anything and the second method worked for me.
Click to expand...
Click to collapse
Yepper thats the method ive been using forever to get into dl mode.
And yea tried the the 2nd way too no dice..
Idk what build number your phone is but build 1010 I'd under product advisory. I had a similar issue and brought it to the att service center and got a brand new cappy v 1008
Sent from my SGH-I897 using XDA App
kwhee07 said:
Idk what build number your phone is but build 1010 I'd under product advisory. I had a similar issue and brought it to the att service center and got a brand new cappy v 1008
Sent from my SGH-I897 using XDA App
Click to expand...
Click to collapse
Off topic, you had a 1010 build, got a replace that is 1008 and you think it's new.
Caution swyping! Read at your own risk.
It sounds dead sir. No idea what ODIN did, but if it's not responding to the power, charger, usb, combo-tricks, etc. It sounds like it's been perma-bricked
If it's still under warranty, it's certainly worth trying to get it replaced... "What the hell is wrong with this phone? It won't turn on anymore?!"
venomio said:
It sounds dead sir. No idea what ODIN did, but if it's not responding to the power, charger, usb, combo-tricks, etc. It sounds like it's been perma-bricked
If it's still under warranty, it's certainly worth trying to get it replaced... "What the hell is wrong with this phone? It won't turn on anymore?!"
Click to expand...
Click to collapse
Can still try a jig.
Look up connexion2005 on this site or get in touch with him on mobiletechreview.com you can also look him up on youtube and his rom in a flash videos. Ghats how I got in touch with him when my phone was fubard and 4 days after I shipped it to him I got it back working like new.
Its well worth the effort to get in touch with him. He is a good guy and I'm sure he can help you.
Sent from my SAMSUNG-SGH-I897 using XDA Premium App
there is no point using a jig. return for warranty. play dumb.
So I made a jig and still dead as anything. Weird, oh well anyone think of anything else? Prob going to see about trying to get art to replace it. Or pay the insurance
Your battery isn't dead is it?
Ha nope at last recall it was around 80% before it happened. And I also tried a fully charged battery from an epic
Sent from my PC36100 using XDA Premium App
I find it hard to believe since a bad flash killed my battery from 96%. But I'm not there so I can't say otherwise. The homemade jig thing from radioshack did not work for me though. I had to use one that was made by one of the members here. I had it plugged in, popped in the battery, and it fired up. Try a couple different combos and see if you get lucky. If I remember correctly it was like 3 tries for me
Yep, verified she's dead..
I hacked a usb cord, and teseted it on an Epic. worked great for the epic..
but the same method on the cappy and she's still dead no life..
/sad panda
how did you make the jig? i bricked mine not to long ago... i didnt use the 301k resistor that you hear about in other threads... i went to radio shack bought a pack of 100k resistors and a pack of 1k .... i soldered three of the 100k and one of the 1k, end to end... then soldered it to the 4 and 5 pin on the stripped charger plug.... this will work... the firmware/kernal/rom changes you have made shouldnt affect the phones ability to get into download mode....
I find it hard to believe since a bad flash killed my battery from 96%. But I'm not there so I can't say otherwise. The homemade jig thing from radioshack did not work for me though. I had to use one that was made by one of the members here. I had it plugged in, popped in the battery, and it fired up. Try a couple different combos and see if you get lucky. If I remember correctly it was like 3 tries for me
Click to expand...
Click to collapse
you dont know what your doing then... if the jig you use from the members worked then you deffinately didnt make urs right.... search these threads there are pictures of what pins to use... you actually dont even have to solder them... just stick the stripped down plug in and touch the ends of the jig to the correct pins... however... do not touch the the actual wires of the jig as it will change the resistance, if that happens it will appear that the jig doesnt work... this is SIMPLE! and if you cant get it to work then youre not following directions, also as he said above.. it doesnt matter that you had 80% before... make sure your battery is charged and try your jig again... that is if you even made one to begin with...
g8tes69 said:
you dont know what your doing then... if the jig you use from the members worked then you deffinately didnt make urs right.... search these threads there are pictures of what pins to use... you actually dont even have to solder them... just stick the stripped down plug in and touch the ends of the jig to the correct pins... however... do not touch the the actual wires of the jig as it will change the resistance, if that happens it will appear that the jig doesnt work... this is SIMPLE! and if you cant get it to work then youre not following directions, also as he said above.. it doesnt matter that you had 80% before... make sure your battery is charged and try your jig again... that is if you even made one to begin with...
Click to expand...
Click to collapse
Cut the guy some slack. Unless you know him or work with him, how do you know he hasn't?
Anyway. Look, I had a similar issue with odin. I didn't run it as admin on win7 and it froze about half way. I unplugged and popped the battery, next thing, it wouldn't start. Since I knew my phone wouldn't work with the 3 button, stock, I tried something else. I let the phone sit for about 5 minutes, came back, put in battery, held the volume buttons as I inserted the usb. Snapped right into download mode.
Not everything works for the same device. It could be that your jig has something wrong with it. Just a thought.
But a hint for the community, unless you know the person you are speaking to personally, don't assume he's lazy and hasn't made his jig.
g8tes69 said:
how did you make the jig? i bricked mine not to long ago... i didnt use the 301k resistor that you hear about in other threads... i went to radio shack bought a pack of 100k resistors and a pack of 1k .... i soldered three of the 100k and one of the 1k, end to end... then soldered it to the 4 and 5 pin on the stripped charger plug.... this will work... the firmware/kernal/rom changes you have made shouldnt affect the phones ability to get into download mode....
Click to expand...
Click to collapse
I exposed the micro usb connector and connected the resistors to the contacts on the board..
Proved that it worked on a epic, booted into dl mode without problem. tried on the cappy and nothing..
Got josh's jig last night. Tried that as well and nothing..
I've scoured this site as well as many other sites and have not found a solution.
i phone is in a soft brick state - phone--!--computer
and i cant find a way to get in to recovery or download mode...
what i've tried:
3button combo - and every permutation of buttons and usb plug ins and battery inserts
home made jig - made with resistors and a multimeter reading of 301k ohms
One-Click unbrick - cant find device perpetually prompts to reinstall drivers
Heimdall one-click 1.3.0 - connects then prompts to install drivers to Samsung USB Composite Device (successful) then repeats process... (did not check box bootloaders)
Super one click - stops responding after waiting for device
Odin3 - cant find device
I've run out of ideas... is anyone else having problems with this?
What else is there that i can do???
the phone to pc screen means a jig or 3 button combo will work (if you have 3 button fix).
try again with jig or order a professional jig.
Homemade jigs are a pain in the ass. Did you wrap them in tape where you're holding them so not to throw off the resistance? It may take a while for you to get them touching the correct pins. That screen means soft brick. Try Heimdall again, that can take a few times. Did you install the drivers for Heimdall? Keep trying because you're only soft bricked. Jig or Heimdall unbrick should work. What were you doing to your phone when this happenned? What ROM is currently on your device? What were you ettempting to do?
http://forum.xda-developers.com/showthread.php?t=944418
This has recovered me from many soft bricks
Only thing I can say is Isolate your fingers from the resistors, make sure your connecting the correct pins and give it a few seconds for the phone to register the jig. (also it might take a min or 2 for your comp to recognize your phone)
If you happen to be on KF1 then you very well might be in DL mode, because they have written in that if that err notice is triggered it will still show even if booted by a jig. You might have to work a lil on your timing.
Also, you can't use ODIN and Heimdall from the same physical USB port on the PC. These drivers are dealing with low level function and are less flexable, so make note of which "com port" hemidall is using and find another for ODIN. Also be picky about which USB port as there seems to be a major difference between ports that are hardwired/built-in to the PC motherboard and others connected by wire. Lastly make sure your using a "good" cable as this has been a problem for many.
The connect reconnect loop makes me think you have a bad cable (really only bad for samsung phones cuz well... samsung).
I've never had a problem with my home made jig. It saved my a$$ on more then one occasion. I did have one problem with flashing GB bootloader, but then I realized that I could still flash with odin.
What phone version do you have (marked under your battery)?
i have sgh-I896
but under "IC" it says SGHI897 ???
My jig manages to turn it on no problem... it just goes to the phone--!--computer thing though..
Edit: I made my jig on a piece of solder board, and i connect them to pin 4 and 5... closest ones to 3.5m jack
Try to run Odin or hemidall after you plug the jig in. I recovered a 7" galaxy tab when it was at the phone! computer screen.
Sent from my Desire HD using XDA Premium App
laxwillsch said:
Try to run Odin or hemidall after you plug the jig in. I recovered a 7" galaxy tab when it was at the phone! computer screen.
Sent from my Desire HD using XDA Premium App
Click to expand...
Click to collapse
I used my jig to turn on my Captivate, wile showing the phone--!--computer logos i plugged in my usb.
my computer recognized it and i opened Heimdall.
It connected and i pressed flash... it then gets stuck on Handshaking loke...
it stays like this for hours.... i left it on over night and all during work...
could it be my usb cord?? its a samsung
Edit: OMG!! its working now... moved usb to behind my computer then used One-Click unbrick.
Thank you all very much
Hey the One Click unbrick detected ur phone in the phone----!---- PC screen? Bcz i have the same problem than u, 3 keys comb were allways locked, my pc cant find the phone and i cant use the ADB commands for get in download, i made a jig and nothing (i think that i did something wrong), i bought one but have to w8 about 5 days more to get it in my hands. I will try connecting my phone in all the usb ports now..
Yea bad usb port seems to be the culprit. Always go with a usb off the motherboard. Jig will always work if the screen turns on.
Sent from my i897 running MIUI 1.8.12 with TalonMTD kernel.
TBStar88 said:
i have sgh-I896
but under "IC" it says SGHI897 ???
My jig manages to turn it on no problem... it just goes to the phone--!--computer thing though..
Edit: I made my jig on a piece of solder board, and i connect them to pin 4 and 5... closest ones to 3.5m jack
Click to expand...
Click to collapse
this has happened to me as well. as long as u install the heimdall drivers you can get around that. i have my heimdall.exe in my c: in downloads. i open up my cmd prompt then type cd\ then press enter to get to the c:. then i put downloads\heimdall close-pc-screen after that as long as u have all ur drivers installed it should boot right up.
I ended upo bricking my phone pretty bad today. Everything I tried is not working and all I'm left with now is to wait for my USB jig to come in which I purchased off eBay. I really hope it works.
^^^ How u manage to do that......? post some more details.
Sent from Dell Streak
My computer crashed while trying to flash an SGS I9000 through Odin. The phone will not boot at all - the screen just stays off. I've tried pulling the battery for extended periods but it makes no difference. I can't get into recovery mode or download mode. The screen seems permanently off.
When I put the battery in and plug the phone into the computer it tries (and fails) to install a driver for a "SEC S59C110 Test B/D".
I've tried the 301K resistor jig but it did not seem to do anything.
Any ideas on what I can do? The phone is long out of warranty, so if the phone is permanently dead then I'll just have to buy a new one (though I'm hoping for a fix, if possible!)
You could try this:
http://forum.xda-developers.com/showthread.php?t=1330491
Sent from my GT-I9000 using XDA Premium App
read this too..
it's basically the same thing, but it talks about the possibility of using the unbrickable mod without doing the hardware mod... (if i got it right) wich i think it is your case because the computer is able to enumerate usb.
http://www.xda-developers.com/android/explaining-and-advancing-the-unbrickable-mod/
good luck!
and let us know
interesting, keep us updated if you try unbrickable
Ozzah said:
..........I've tried the 301K resistor jig but it did not seem to do anything.........
Any ideas on what I can do? The phone is long out of warranty, so if the phone is permanently dead then I'll just have to buy a new one (though I'm hoping for a fix, if possible!)
Click to expand...
Click to collapse
It's very strange that the jig fails on these situation.
Maybe that the jig is not correctly built....
Why don't you try with another usb dongle?
I hope that you solve your problem.
I can't believe it - I'm absolutely astounded. UnBrickable and Heimdall worked and they brought the phone back to life! Thank you guys so much!
you did the hardware mod for unbrickable?
No, I dismantled the phone and when I saw how tiny the resistors were I shat my pants.
I tried it without doing the hardware mods first, and I was going to mod it only if it failed (which, fortunately, it didn't!)
you lucky one then if the bootloader would be f.... up you would have to techmod
but anyways gg ;]
Hello, guys.. I'm having a real trouble with my Note. I bought it 3 months ago, but it seems that today's my "lucky" day and the microUSB connector isn't working anymore. At all. No charging, no "usb connected", no mass storage. It's not charging even when I turn off the phone and plug the charger.
So.. I guess I have to ask for a repair or a replacement. But here's the problem. I've changed both the kernel and the ROM and I have to restore the phone to it's original state before taking it to the service. I read the UNroot topic under the development section, but I didn't understand it well. I need to do it through the phone since I can't connect the device to my computer because of the malfunctioning microUSB port. I can't charge the battery either, so I'm stuck with only 36% power and I can't simply shoot in the dark. I turned the phone to save the power and I hope it should be enough to finish the operation, but I don't really know how to start it. I guess I have to download stock kernal and stock ROM and then flash it somehow (Mobile Odin!?), but I'm not sure and I really need your help.
Any help would be highly appreciated, I'll continue looking around for info.
10x in advance
a lot of users suggest others - who are having a similar problem with you, to try cleaning the usb port...
musashiro said:
a lot of users suggest others - who are having a similar problem with you, to try cleaning the usb port...
Click to expand...
Click to collapse
It looks clean. The cable is okay too. I'm working at Gameloft so we have lot's of micro-usb devices and they're working just fine with the exact same PC and cable.
Anyway, to be 100% sure - how to clean the port? I mean - it's so tiny little hole and there isn't any direct access to it.. But I think it's gone.. It randomly shows "charging" while the cable is not plugged at all. Then it stops.. and starts again.
ZeroCGTI said:
Hello, guys.. I'm having a real trouble with my Note. I bought it 3 months ago, but it seems that today's my "lucky" day and the microUSB connector isn't working anymore. At all. No charging, no "usb connected", no mass storage. It's not charging even when I turn off the phone and plug the charger.
So.. I guess I have to ask for a repair or a replacement. But here's the problem. I've changed both the kernel and the ROM and I have to restore the phone to it's original state before taking it to the service. I read the UNroot topic under the development section, but I didn't understand it well. I need to do it through the phone since I can't connect the device to my computer because of the malfunctioning microUSB port. I can't charge the battery either, so I'm stuck with only 36% power and I can't simply shoot in the dark. I turned the phone to save the power and I hope it should be enough to finish the operation, but I don't really know how to start it. I guess I have to download stock kernal and stock ROM and then flash it somehow (Mobile Odin!?), but I'm not sure and I really need your help.
Any help would be highly appreciated, I'll continue looking around for info.
10x in advance
Click to expand...
Click to collapse
Put stock rom on your external sd,install mobile odin pro from market and use it to flash the stock rom.And remember donot select ever root,inject su,inject mobile odin.And after it finish flashing,you can send it for service
Put a stock rom and then try cleaning the USB as someone suggested. My usb port would stop working at random and I cleaned the port with a toothbrush and it has worked ever since. That was 2-3 months ago.
Well, thanks guys.. I'll try the tooth-brush trick when I get home and if it fails to solve the problem, I'm gonna flash the stock ROM with MOP and take it to the service. I'll keep you posted.
ZeroCGTI said:
It looks clean. The cable is okay too. I'm working at Gameloft so we have lot's of micro-usb devices and they're working just fine with the exact same PC and cable.
Anyway, to be 100% sure - how to clean the port? I mean - it's so tiny little hole and there isn't any direct access to it.. But I think it's gone.. It randomly shows "charging" while the cable is not plugged at all. Then it stops.. and starts again.
Click to expand...
Click to collapse
Work at GAMELOFT?!? Tell them to turn off the air push ads in my PAID game Shark Dash (turning them off in settings does ansolutey nothing)... Three emails to your support and NO reply. Pathetic
ZeroCGTI said:
Hello, guys.. I'm having a real trouble with my Note. I bought it 3 months ago, but it seems that today's my "lucky" day and the microUSB connector isn't working anymore. At all. No charging, no "usb connected", no mass storage. It's not charging even when I turn off the phone and plug the charger.
So.. I guess I have to ask for a repair or a replacement. But here's the problem. I've changed both the kernel and the ROM and I have to restore the phone to it's original state before taking it to the service. I read the UNroot topic under the development section, but I didn't understand it well. I need to do it through the phone since I can't connect the device to my computer because of the malfunctioning microUSB port. I can't charge the battery either, so I'm stuck with only 36% power and I can't simply shoot in the dark. I turned the phone to save the power and I hope it should be enough to finish the operation, but I don't really know how to start it. I guess I have to download stock kernal and stock ROM and then flash it somehow (Mobile Odin!?), but I'm not sure and I really need your help.
Any help would be highly appreciated, I'll continue looking around for info.
10x in advance
Click to expand...
Click to collapse
download stock... flash it with mobile odin... dont forget to untick the forever root and cmw injection... ur note will be good as new...
sorry didint see vijays post... he has posted already...
kvsandeepreddy said:
download stock... flash it with mobile odin... dont forget to untick the forever root and cmw injection... ur note will be good as new...
sorry didint see vijays post... he has posted already...
Click to expand...
Click to collapse
If you want bone stock you have to use PC Odin not mobile
Atrix_E said:
If you want bone stock you have to use PC Odin not mobile
Click to expand...
Click to collapse
out of curiosity... what difference do u c when u flash a stock with pc odin or mobile odin???
kvsandeepreddy said:
out of curiosity... what difference do u c when u flash a stock with pc odin or mobile odin???
Click to expand...
Click to collapse
Not a difference you "see" technically. From my understanding mobile Odin cannot touch bootloaders. Pc Odin can. Someone can correct me if I'm wrong. From Chainfires first.post in his Mobile Odin thread, "While in theory Mobile ODIN can repartition and flash EFS and bootloaders, it will cowardly refuse to do so, for your own safety."
Atrix_E said:
If you want bone stock you have to use PC Odin not mobile
Click to expand...
Click to collapse
But his usb port doesnt work
vijai2011 said:
But his usb port doesnt work
Click to expand...
Click to collapse
Hadn't had my coffee yet lol. I woke up to an air push ad asking me to play Shark Dash
Atrix_E said:
Hadn't had my coffee yet lol. I woke up to an air push ad asking me to play Shark Dash
Click to expand...
Click to collapse
Lol go and sleep again thn...
Try another usb cable. You might be able to find one that fit better to the Note.
vijai2011 said:
Lol go and sleep again thn...
Click to expand...
Click to collapse
I'm about to carve up this shark and eat him for breakfast
Assumign that you have a micro SD in the slot-
Take the micro SD out and connect it to your computer. Or use airdroid for file transfer over wifi. Whichever way you use, create a folder called firmware and put the .md5 in the folder and flash it through CWM or mobile odin.
Atrix_E said:
I'm about to carve up this shark and eat him for breakfast
Click to expand...
Click to collapse
I already sent you a personal message.. And I'm not responsible for your problems btw! I'm not customer support after all..
ZeroCGTI said:
I already sent you a personal message.. And I'm not responsible for your problems btw! I'm not customer support after all..
Click to expand...
Click to collapse
Not just my problems but many other paid users if you read the Market comments. I know you're not responsible but if you're QA like you said, technically you are.
Anilisali method will work btw.
Atrix_E said:
Not just my problems but many other paid users if you read the Market comments. I know you're not responsible but if you're QA like you said, technically you are.
Anilisali method will work btw.
Click to expand...
Click to collapse
I'm a WEB-Tester, not a game tester It's not my business at all. Anyway, I asked for your email address if you're willing to get some help from me. Send me a PM and I'll see what I can do for you.
Hello, my situation is this: S3 Mini running Carbon Rom 4.4.4 , flashed with TWRP. After running great for a few weeks, suddenly after charging all night the phone froze ( was on FB on CM Browser). It was totally unresponsive to any attempts so I pulled the battery ( this did happen a couple times before) and when I tried to restart, nothing. The phone responds to nothing, no download, no recovery, no charger.... battery is charged and I did try a different battery to no avail. The only response I get is if it is connected to a PC before I install the battery then when I install it (the battery) the PC tries to install u8500 usb rom drivers, which of course it never finds. Samsung device drivers are installed on the PC. Odin also fails to see it.
Is it dead? Is it salvageable? Can I recover any data off it?
Sorry for the new thread but it seemed I could not find a case exactly like mine.
Pino Fundez said:
Hello, my situation is this: S3 Mini running Carbon Rom 4.4.4 , flashed with TWRP. After running great for a few weeks, suddenly after charging all night the phone froze ( was on FB on CM Browser). It was totally unresponsive to any attempts so I pulled the battery ( this did happen a couple times before) and when I tried to restart, nothing. The phone responds to nothing, no download, no recovery, no charger.... battery is charged and I did try a different battery to no avail. The only response I get is if it is connected to a PC before I install the battery then when I install it (the battery) the PC tries to install u8500 usb rom drivers, which of course it never finds. Samsung device drivers are installed on the PC. Odin also fails to see it.
Is it dead? Is it salvageable? Can I recover any data off it?
Sorry for the new thread but it seemed I could not find a case exactly like mine.
Click to expand...
Click to collapse
I had the same issue after flashing a wrong bootloader. I gave the phone back where I bought it telling that I doesn't know why he didn't started anymore. They replaced my telephone motherboard and now it works.
theov3rc0mer said:
I had the same issue after flashing a wrong bootloader. I gave the phone back where I bought it telling that I doesn't know why he didn't started anymore. They replaced my telephone motherboard and now it works.
Click to expand...
Click to collapse
There's no warranty on my device so taking it back is not an option. The phone was working fine for while so I suppose it's not the bootloader... what suprised me is that it happened outta the blue, not during start up... thanks for the advice though mate.
Pino Fundez said:
There's no warranty on my device so taking it back is not an option. The phone was working fine for while so I suppose it's not the bootloader... what suprised me is that it happened outta the blue, not during start up... thanks for the advice though mate.
Click to expand...
Click to collapse
I think you can try with an usb jig or you can find someone with a jtag (there are millions of guides about those solutions, just google it). :good:
theov3rc0mer said:
I think you can try with an usb jig or you can find someone with a jtag (there are millions of guides about those solutions, just google it). :good:
Click to expand...
Click to collapse
The jig I can do, no harm trying but the jtag is hard to find....
Guys i have this exact same problem and i'm getting desperate. i remember there was a special usb cable but i can't remember the name...
Could you please link me to anything? Absolutely anything? i really need this phone alive
M4v3r1cX said:
Guys i have this exact same problem and i'm getting desperate. i remember there was a special usb cable but i can't remember the name...
Could you please link me to anything? Absolutely anything? i really need this phone alive
Click to expand...
Click to collapse
basically from what I've read, the jig you either buy off Ebay for 3$ or solder 300kΩ across pins 4 and 5 of a micro usb connector, But look it up before cause a nuclear holocaust
Pino Fundez said:
basically from what I've read, the jig you either buy off Ebay for 3$ or solder 300kΩ across pins 4 and 5 of a micro usb connector, But look it up before cause a nuclear holocaust
Click to expand...
Click to collapse
Today i bought the usb jib and... no, it didn't work. God damn
I guess i'll just let the phone die and i'll buy a new one... it was a good phone.
M4v3r1cX said:
Today i bought the usb jib and... no, it didn't work. God damn
I guess i'll just let the phone die and i'll buy a new one... it was a good phone.
Click to expand...
Click to collapse
Honestly, I didnt think the jig would work, which is why Im not in much haste to do it, before you dump it though mate, try and find someone close to you with a JTAG setup.... I havent had much luck with that.
It was an ok phone... either I had high expectations or it was below the hype but that is just my 2 cents... at the end of the day it was a useful tool....