i was in Xrecovery>avanced moving stuffs and i did something like unmount something and restart, then my cel cant boot by any kind of stuffs, like flash, or press back botton. (sorry my english.)
now i cant make it boot stuck in Sony ericson logo.
Vlackrs said:
i was in Xrecovery>avanced moving stuffs and i did something like unmount something and restart, then my cel cant boot by any kind of stuffs, like flash, or press back botton. (sorry my english.)
now i cant make it boot stuck in Sony ericson logo.
Click to expand...
Click to collapse
Use PC companion or SUES to restore the original firmware back then re-root your phone and install your chosen ROM and boom you're back.
smyth12 said:
Use PC companion or SUES to restore the original firmware back then re-root your phone and install your chosen ROM and boom you're back.
Click to expand...
Click to collapse
GingerDX i have installed before this problem, i will try to do what you say, brb
Vlackrs said:
GingerDX i have installed before this problem, i will try to do what you say, brb
Click to expand...
Click to collapse
After re-rooting your phone you can once again install GingerDX.. Just don't mess with settings you're not sure of
PC companion not work cuz i cant boot my phone =( im stuck in sony ericson, and where i can find SUES? ty
SEUS is no longer available... you have to plug your phone into the computer, remove the battery, on PC companion it will say "Repair this phone" in small lettering, click that then with your phone connected to the computer via USB hold the back button and put your battery in, this will put your phone into Flash mode and allow PC companion to repair your phone
i love you dude, thank you, i will not mess up again with that XD, btw i have a year using this website is awesome, i was trying to learn more about Xrecovery and CWM ty!!
What do you mean you have a gear using this website?
CWM and Xrecovery can be dangerous..
No problem!
haha my bad, "year", btw PC companion cant find a software to install, right now im talking to Sony ericson.
i think cuz i have other baseband =S
Hmm, I had this problem, just yesterday infact, I still had access to recovery though... I'm not sure what you should do, I think SE will tell you to send the phone back to them to be honest..
yea my phone its dead, QQ, lets get iphone 5 this new year, ty Smyth12 anyways
Vlackrs said:
yea my phone its dead, QQ, lets get iphone 5 this new year, ty Smyth12 anyways
Click to expand...
Click to collapse
There still is a way to fix the phone using PC companion, the baseband doesn't matter.. as far as I know, don't quote me on that... hmm.. When I think of something I will let you know
Guys, forget PC Companion (PCC) and Update Service (SEUS) ...
If your phone still gets to the Sony Ericsson Logo, or still shows some sign of life so you can be sure that the bootloader and kernel (STOCK Kernel - I don't know if this works with custom kernels as well) is still alive, restore your device this way:
Make sure you have a Java Runtime installed.
If you're on a 64-Bit Windows Edition you NEED to have the 32-Bit JRE installed!
Make sure you have the Android drivers installed
(should already be the case if you installed PC Companion / Update Service)
Download Flashtool 0.2.9.1
Extract it to C:\Flashtool
Download Android 2.1.1.C.0.0
Copy the "X8_2.1.1.C.0.0._un.ftf" you just downloaded INTO the "firmwares" folder inside the Flashtool directory.
Disconnect your phone from the computer and turn it OFF!
Now start the X10FlashTool.exe in C:\Flashtool
Plug the USB cable into JUST your phone (NOT into the computer!).
Click "Flash" in Flashtool and select X8_2.1.1.C.0.0._un.ftf you copied into the Firmwares folder.
In the next window don't do anything, just click "OK"
Flashtool will show you a window about what you have to do:
- PRESS and HOLD the BACK button of your phone.
- Connect the USB cable to your computer. Keep the button PRESSED!
- If Windows is nagging about installing drivers - let it do its job. Keep the button PRESSED!
- Once you see output happening in Flashtool's window you can release the back button of the phone.
Patiently wait until flashing finished.
Now, as Flashtool will tell you ... disconnect the phone and turn it on.
BE PATIENT - the first boot can take a few minutes.
Once the phone booted up ...
Enable "Unknown Sources" and "USB Debugging" in your phone's settings.
Connect the phone back to the computer.
Press "Root" and let Flashtool root the Droid.
A automatic reboot will follow!
Once the phone finished rebooting ...
Press "Ask root perm" and look at your phone. You will get a popup from Superuser to grant su permissions. Confirm the request!
Now click "xRecovery" to inject xRecovery into your phone.
Done ...
Now you can go ahead and install a xRecovery compatible ROM (i.e. FroyoPro).
Download the ZIP you want to flash and push it to your phone's SD card. Example:
adb push C:\Users\<your_username>\Downloads\FroyoPro-v1.1.zip /sdcard
(you need to input that command in a Command Prompt)
If you want GingerDX back on your phone ...
- Download GingerDX v013 and copy it onto your phone's SD card (i.e. by ADB)
- Download GingerDX v020 and copy it onto your phone's SD card (i.e. by ADB)
- From Flashtool make the phone to reboot into xRecovery.
- Flash GingerDX v013 in xRecovery.
- Reboot
- Keep tapping on the screen once the Sony Ericsson Logo appears to get into CWM.
- Flash GingerDX v020 in CWM.
- Full-Wipe ("Factory Reset")
- Reboot
I just revived my X8 a few hours ago by this way after a update flash went terribly wrong for reasons I'm not able to tell.
ty, and ive trying to fix it but nop, nothing.
smyth12 said:
Hmm, I had this problem, just yesterday infact, I still had access to recovery though... I'm not sure what you should do, I think SE will tell you to send the phone back to them to be honest..
Click to expand...
Click to collapse
If you can access recovery, then simply install your rom agen.
Sent from my MT15i using Tapatalk
B.Jay said:
Guys, forget PC Companion (PCC) and Update Service (SEUS) ...
If your phone still gets to the Sony Ericsson Logo, or still shows some sign of life so you can be sure that the bootloader and kernel (STOCK Kernel - I don't know if this works with custom kernels as well) is still alive, restore your device this way:
Make sure you have a Java Runtime installed.
If you're on a 64-Bit Windows Edition you NEED to have the 32-Bit JRE installed!
Make sure you have the Android drivers installed
(should already be the case if you installed PC Companion / Update Service)
Download Flashtool 0.2.9.1
Extract it to C:\Flashtool
Download Android 2.1.1.C.0.0
Copy the "X8_2.1.1.C.0.0._un.ftf" you just downloaded INTO the "firmwares" folder inside the Flashtool directory.
Disconnect your phone from the computer and turn it OFF!
Now start the X10FlashTool.exe in C:\Flashtool
Plug the USB cable into JUST your phone (NOT into the computer!).
Click "Flash" in Flashtool and select X8_2.1.1.C.0.0._un.ftf you copied into the Firmwares folder.
In the next window don't do anything, just click "OK"
Flashtool will show you a window about what you have to do:
- PRESS and HOLD the BACK button of your phone.
- Connect the USB cable to your computer. Keep the button PRESSED!
- If Windows is nagging about installing drivers - let it do its job. Keep the button PRESSED!
- Once you see output happening in Flashtool's window you can release the back button of the phone.
Patiently wait until flashing finished.
Now, as Flashtool will tell you ... disconnect the phone and turn it on.
BE PATIENT - the first boot can take a few minutes.
Once the phone booted up ...
Enable "Unknown Sources" and "USB Debugging" in your phone's settings.
Connect the phone back to the computer.
Press "Root" and let Flashtool root the Droid.
A automatic reboot will follow!
Once the phone finished rebooting ...
Press "Ask root perm" and look at your phone. You will get a popup from Superuser to grant su permissions. Confirm the request!
Now click "xRecovery" to inject xRecovery into your phone.
Done ...
Now you can go ahead and install a xRecovery compatible ROM (i.e. FroyoPro).
Download the ZIP you want to flash and push it to your phone's SD card. Example:
adb push C:\Users\<your_username>\Downloads\FroyoPro-v1.1.zip /sdcard
(you need to input that command in a Command Prompt)
If you want GingerDX back on your phone ...
- Download GingerDX v013 and copy it onto your phone's SD card (i.e. by ADB)
- Download GingerDX v020 and copy it onto your phone's SD card (i.e. by ADB)
- From Flashtool make the phone to reboot into xRecovery.
- Flash GingerDX v013 in xRecovery.
- Reboot
- Keep tapping on the screen once the Sony Ericsson Logo appears to get into CWM.
- Flash GingerDX v020 in CWM.
- Full-Wipe ("Factory Reset")
- Reboot
I just revived my X8 a few hours ago by this way after a update flash went terribly wrong for reasons I'm not able to tell.
Click to expand...
Click to collapse
awesome i will try this!!! i will reply later.
taaviu said:
If you can access recovery, then simply install your rom agen.
Sent from my MT15i using Tapatalk
Click to expand...
Click to collapse
im the problem not "smyth12", but i cant do anything not even get into my xrecovery, i think what i did was unmount the file system using recovery by error, or some important file to boot at least with Xrecovery.
@B.Jay
Its working!!! that .FTF save me!!! <33333333333 thank you!!!
Vlackrs said:
@B.Jay
Its working!!! that .FTF save me!!! <33333333333 thank you!!!
Click to expand...
Click to collapse
You're welcome mate.
Remember to keep the instructions and required files save in case you manage to soft-brick the device again.
i dont understand this .
Related
Please help i just isntalled new ROM for my xperai x8 and now when i restarted it it is stuck at SE logo and stays there.I tried to enter to xrecovery but it cant enter like i dont have xrecovery but i actually do. Now when i try to put my phoen i nflash mode it says taht my usb device isnt recognised but it was a day ago. Moreover i reinstalled windwos usb drivers and Xperia SEMC flash drivers to see if this is the problem but its not it still cant recognise it so i am stuck at SE logo , xrecovery cant run , myPC doesnt recognise the phone in flash mode.... Please help !
This method will install the original software on your X8!
If you have Sony PC Companion 2.1 on your PC, then uninstall it, and download and install Sony PC Companion 2.1, again! If not, then PC Companion might not recognize your phone. After installing do the following:
- Turn off the phone, and unplug it from the PC
- Turn on Sony PC Companion on your PC
- In PC Companion, enter the Support Zone tab
- Go to Update Phone Software
A window will pop out, saying that it cannot find your phone
- Click on Fix Phone
- Click on Continue
A window will pop out, saying that you will lose all your data
- TICK the BOX
- Click on continue
An update process will began.
Wait for it to show a window with all the SONY mobile phones
- Find your phone (X8)
- Click on the phone.
Now all you have to do is follow the on-screen instructions. It will tell you to hold the back button and plug your turned-off X8 to the PC, then it will erase everything, and download the original 2.1 ROM to your X8.
yes
WhatWhatInTheButt said:
This method will install the original software on your X8!
If you have Sony PC Companion 2.1 on your PC, then uninstall it, and download and install Sony PC Companion 2.1, again! If not, then PC Companion might not recognize your phone. After installing do the following:
- Turn off the phone, and unplug it from the PC
- Turn on Sony PC Companion on your PC
- In PC Companion, enter the Support Zone tab
- Go to Update Phone Software
A window will pop out, saying that it cannot find your phone
- Click on Fix Phone
- Click on Continue
A window will pop out, saying that you will lose all your data
- TICK the BOX
- Click on continue
An update process will began.
Wait for it to show a window with all the SONY mobile phones
- Find your phone (X8)
- Click on the phone.
Now all you have to do is follow the on-screen instructions. It will tell you to hold the back button and plug your turned-off X8 to the PC, then it will erase everything, and download the original 2.1 ROM to your X8.
Click to expand...
Click to collapse
thanks mate i will try it now
lol
It doesn't work it says that Pc companion was not able to connect to the device. I tried many things bu pc companion just cant connect my phone and windows keep saying that error that i am plugging unknown device which is a bull**** the day before it was working fine...
For all people who didnt understand iCANT ENTER IN FLASH MODE I MEAN I CAN BUT ITS NOT RECOGNISED so i cant update my software.
also
also flash tool in the console says that it cant determine what deviec i am plugging into and cant display what is busybox version or anything like i am putting an unknown device...
27/043/2012 15:43:10 - ERROR - Cannot identify your device. Found sh while expecting X10, E10, U20 or E15 (read from ro.product.model from build.prop)
Hey there, my phone isn't bricked...but I think I have too much data (possibly conflicting roms installed at the same time??) and I wish to reset my phone to its original status... I wish to re-install a ROM on it, but I want to start fresh again by removing the rooting programs or what have you..
Would following these steps put it all back to its original setting, also meaning that I could completely wipe the SD clean?
If so, would this mean I would have to re-root my X8? Not that it would be a problem but I would just like to know if it would be needed!
Thanks!
Regards,
Nev51289
yes
Nev51289 said:
Hey there, my phone isn't bricked...but I think I have too much data (possibly conflicting roms installed at the same time??) and I wish to reset my phone to its original status... I wish to re-install a ROM on it, but I want to start fresh again by removing the rooting programs or what have you..
Would following these steps put it all back to its original setting, also meaning that I could completely wipe the SD clean?
If so, would this mean I would have to re-root my X8? Not that it would be a problem but I would just like to know if it would be needed!
Thanks!
Regards,
Nev51289
Click to expand...
Click to collapse
Yes do as the guy above said...No need to root your phone
Sorry, just to clarify - you mean I wouldn't need to go through the whole rooting process again after doing a full reset/wipe what have you? Thanks by the way
lol
Nev51289 said:
Sorry, just to clarify - you mean I wouldn't need to go through the whole rooting process again after doing a full reset/wipe what have you? Thanks by the way
Click to expand...
Click to collapse
if you want to restore the stock rom (original androdi on xperia x8) with pc Comapnion than you dont need to root it again. But if you want to change it to custom rom and you have done full wipe i think you should root it again (rooting is done so taht you can change the busybox version of the phone and upload xrecovery if you have those you don't need to root)
eastman47 said:
It doesn't work it says that Pc companion was not able to connect to the device. I tried many things bu pc companion just cant connect my phone and windows keep saying that error that i am plugging unknown device which is a bull**** the day before it was working fine...
For all people who didnt understand iCANT ENTER IN FLASH MODE I MEAN I CAN BUT ITS NOT RECOGNISED so i cant update my software.
Click to expand...
Click to collapse
Why don't you download the store Rom annd use Flashtool to flash it? Then you may be able to upgrade to latest revision with PCC.
eastman47 said:
if you want to restore the stock rom (original androdi on xperia x8) with pc Comapnion than you dont need to root it again. But if you want to change it to custom rom and you have done full wipe i think you should root it again (rooting is done so taht you can change the busybox version of the phone and upload xrecovery if you have those you don't need to root)
Click to expand...
Click to collapse
Can I consequently delete Busybox? If it is a deleteable app that is!
use the update service
eastman47 said:
It doesn't work it says that Pc companion was not able to connect to the device. I tried many things bu pc companion just cant connect my phone and windows keep saying that error that i am plugging unknown device which is a bull**** the day before it was working fine...
For all people who didnt understand iCANT ENTER IN FLASH MODE I MEAN I CAN BUT ITS NOT RECOGNISED so i cant update my software.
Click to expand...
Click to collapse
Yeah, I lost you somewhere... If after taking out the battery, you CAN NOT enter xrecovery or CWM, then, you either can try THIS THREAD <--- go on, click on it!, or, you have to do what I had to do a couple of times, which is to restore your X8 to its original state, and to do that with Sony PC Companion, you first have to UNINSTALL your current PC Companion!!! THEN, restart your PC, and install a clean version of Sony PC Companion 2.1!
IT DOESN'T MATTER IF YOU HAVE THE LATEST VERSION of PC Companion, YOU STILL HAVE TO UNINSTALL IT, AND INSTALL IT AGAIN!!! IF YOU DON'T, THERE's a 99% CHANCE THAT PC COMPANION WILL NOT RECOGNIZE YOUR PHONE!!! ...I don't know why, but it's probably some marketing trick, since I once used this method 3 times in a row, then the fourth time PC Companion didn't recognize my X8. This happened on both, the old PC Companion, and the current Sony version 2.1. I tested them both on purpose, to eliminate the possibility that I damaged my X8's hardware somehow, during a high speed impact collision with the bedroom wall...
Once you reinstall Sony PC Companion 2.1, go back to my first post to your problem, and follow it step-by-step.
AND yes, if you want to install custom ROM's again, then you will have to ROOT your phone again, and UNLOCK the BOOTLOADER, etc...
BUT, if it's a soft-brick, then you might be able to redeem yourself
ViVA FIDELINO!
how about kernel?
WhatWhatInTheButt said:
This method will install the original software on your X8!
If you have Sony PC Companion 2.1 on your PC, then uninstall it, and download and install Sony PC Companion 2.1, again! If not, then PC Companion might not recognize your phone. After installing do the following:
- Turn off the phone, and unplug it from the PC
- Turn on Sony PC Companion on your PC
- In PC Companion, enter the Support Zone tab
- Go to Update Phone Software
A window will pop out, saying that it cannot find your phone
- Click on Fix Phone
- Click on Continue
A window will pop out, saying that you will lose all your data
- TICK the BOX
- Click on continue
An update process will began.
Wait for it to show a window with all the SONY mobile phones
- Find your phone (X8)
- Click on the phone.
Now all you have to do is follow the on-screen instructions. It will tell you to hold the back button and plug your turned-off X8 to the PC, then it will erase everything, and download the original 2.1 ROM to your X8.
Click to expand...
Click to collapse
>> how about kernel? for example your phone allready back to 2.1 rom and you are using custom kernel before i done this update? like kernel aA-11? is it possible to turn on phone even if im using custom kernel? please give me steps how to bring it back, because im currenty using mini cm7 / kernel aA-11, and i want to bring back my xperia x8 to original rom and kernel
Try downloading the stock rom and a diff version of flashtool. I can't remembet which version is most recommended (try searchibg xda - i read it here). install drivers in flashtool's driver folder (gordon's gate) then try again. Almost the same thing happened to me. PCC won't recognize my phone so I couldn't install the drivers.
X8 stuck at SE logo
I am facing same problem. I have been using GingerDX for long time wanted to change the ROM, however after I change the rom through Xrecovery. Phone restarted and stuck at SE logo.
I tried with SE PC companion but it gives error.
I tried Flashtool, used different ftf file but cant help.
Please help. I am unable to start phone....Please guide me...
Maybe u can also try sus (sony update service). I have experience this n done with sus.
Me n my W8:-D
Vishal9890 said:
I am facing same problem. I have been using GingerDX for long time wanted to change the ROM, however after I change the rom through Xrecovery. Phone restarted and stuck at SE logo.
I tried with SE PC companion but it gives error.
I tried Flashtool, used different ftf file but cant help.
Please help. I am unable to start phone....Please guide me...
Click to expand...
Click to collapse
The best way, if u still can't get on your phone , is take it to the SE Customer care. And don't tell a word about rooting or anything. Just ask them to repair the phone, saying that one morning, the SE logo kept on popping up.
Sent from my XPERIA W8 using xda platinum
I have YouTube video tutorial on my channel - search GaganSJ1 in YouTube and scroll down till you found
Press thanks if it helped
Sent from my E15i using XDA
eastman47 said:
Please help i just isntalled new ROM for my xperai x8 and now when i restarted it it is stuck at SE logo and stays there.I tried to enter to xrecovery but it cant enter like i dont have xrecovery but i actually do. Now when i try to put my phoen i nflash mode it says taht my usb device isnt recognised but it was a day ago. Moreover i reinstalled windwos usb drivers and Xperia SEMC flash drivers to see if this is the problem but its not it still cant recognise it so i am stuck at SE logo , xrecovery cant run , myPC doesnt recognise the phone in flash mode.... Please help !
Click to expand...
Click to collapse
check out this video http://www.youtube.com/watch?v=l7B-7tDaB5U
press thanks if it helped
It seems my LT30p lost flashmode.
After upgrading to 7.0.A.3.195 via "Sony PC Companion 2.1" I flashed the older LT30p_4.0.4_Vodafone.ftf with the flashtool to get back root option.
All works fine.
Now I want to flash the "LT30p_7.0.A.3.195_Vodafone_DE.ftf" I created from the "Sony PC Companion" folder with flashtool.
My problem is, the phone only is able to go into fastboot mode (irrelevant pressing volume down or up).
I re-installed the flashtool-drivers without any improvements.
What have I done and how am I able to get back the flashmode mode for my phone?
Thanks in advance.
harowa said:
It seems my LT30p lost flashmode.
After upgrading to 7.0.A.3.195 via "Sony PC Companion 2.1" I flashed the older LT30p_4.0.4_Vodafone.ftf with the flashtool to get back root option.
All works fine.
Now I want to flash the "LT30p_7.0.A.3.195_Vodafone_DE.ftf" I created from the "Sony PC Companion" folder with flashtool.
My problem is, the phone only is able to go into fastboot mode (irrelevant pressing volume down or up).
I re-installed the flashtool-drivers without any improvements.
What have I done and how am I able to get back the flashmode mode for my phone?
Thanks in advance.
Click to expand...
Click to collapse
You seem to be going around the houses. If you flash that you will lose root again. The only way to root on .195 is with an unsecure kernal and unlocked bootloader.
Just upgrade again through pccompanion and then unlock bootloader and flash advanced stock kernel v4.
gregbradley said:
You seem to be going around the houses. If you flash that you will lose root again. The only way to root on .195 is with an unsecure kernal and unlocked bootloader.
Just upgrade again through pccompanion and then unlock bootloader and flash advanced stock kernel v4.
Click to expand...
Click to collapse
Thank you. I know that at first I lost root again.
I thought (and that's I understood from that post: http://forum.xda-developers.com/showpost.php?p=33568696&postcount=48) that it will possible to flash the ftf file instead of using the "PC Companion" software. I am not happy to lose my holo hd launcher's settings e.g.
I hoped it will work as you described here:
Part 2. Rooting
If you are on 7.0.A.1.303, follow Bin4ry's method from post 2.
If you are on 7.0.A.3.195, follow the other method in the how to root section from post 2.
Click to expand...
Click to collapse
I wanted to follow this direction:
[Root method] via Flashtool instructions. Credit to Androxyde.
Click to expand...
Click to collapse
But I don't understand why the "flashboot mode" will not reached, my phone only comes into fastboot mode.
Sorry for noob questions, I am native german speaker and school (and english) are many years ago. The Xperia T is my first Sony, I come from Samsung Galaxy phones.
harowa said:
Thank you. I know that at first I lost root again.
I thought (and that's I understood from that post: http://forum.xda-developers.com/showpost.php?p=33568696&postcount=48) that it will possible to flash the ftf file instead of using the "PC Companion" software. I am not happy to lose my holo hd launcher's settings e.g.
But I don't understand why the "flashboot mode" will not reached, my phone only comes into fastboot mode.
.
Click to expand...
Click to collapse
OK, There is no such thing as flashboot mode. Its either flashmode or fastboot.
Try this
download and install latest flashtool.
Goto driver folder and install drivers for fastboot/flashmode/xperia tx
Then open flashtool and drag and drop the .ftf you want to flash into the open window of flashtool. Wait untill flashtool tells you to connect phone.
Turn phone off, count to 10, hold volume down button and connect usb cable
gregbradley said:
OK, There is no such thing as flashboot mode. Its either flashmode or fastboot.
Try this
download and install latest flashtool.
Goto driver folder and install drivers for fastboot/flashmode/xperia tx
Then open flashtool and drag and drop the .ftf you want to flash into the open window of flashtool. Wait untill flashtool tells you to connect phone.
Turn phone off, count to 10, hold volume down button and connect usb cable
Click to expand...
Click to collapse
Sorry ma fault. I mean flashmode and not "flashboot mode". I wrote it from memory.
I allready have installed the drivers (it works for a few days, I wrote in the op), i re-installed them, too bevor I wrote the op.
I turned my phone off und waited until an hour!
02/027/2012 13:27:15 - INFO - Selected LT30p_7.0.A.3.195_2_Vodafone_DE.ftf
02/027/2012 13:27:15 - INFO - Preparing files for flashing
02/027/2012 13:27:20 - INFO - Please connect your device into flashmode.
02/027/2012 13:27:28 - INFO - Device connected in fastboot mode
02/027/2012 13:27:39 - INFO - Flash canceled
02/027/2012 13:27:43 - INFO - Device disconnected
The phone never goes to flashmode since flashing the older ftf, only in fastboot mode, no matter if I hold the bottom down or up button.
That's the problem. I don#t know what happend to the phone, but there is no flashmode any more.
It might be, that there is no flashmode with that ftf?
I got it from your post http://forum.xda-developers.com/showpost.php?p=32978312&postcount=3
[STOCK FIRMWARE] Xperia T [LT30p] 7.0.A.1.303 [Vodafone UK] FTF by gregbradley
Click to expand...
Click to collapse
harowa said:
Sorry ma fault. I mean flashmode and not "flashboot mode". I wrote it from memory.
I allready have installed the drivers (it works for a few days, I wrote in the op), i re-installed them, too bevor I wrote the op.
I turned my phone off und waited until an hour!
02/027/2012 13:27:15 - INFO - Selected LT30p_7.0.A.3.195_2_Vodafone_DE.ftf
02/027/2012 13:27:15 - INFO - Preparing files for flashing
02/027/2012 13:27:20 - INFO - Please connect your device into flashmode.
02/027/2012 13:27:28 - INFO - Device connected in fastboot mode
02/027/2012 13:27:39 - INFO - Flash canceled
02/027/2012 13:27:43 - INFO - Device disconnected
The phone never goes to flashmode since flashing the older ftf, only in fastboot mode, no matter if I hold the bottom down or up button.
That's the problem. I don#t know what happend to the phone, but there is no flashmode any more.
It might be, that there is no flashmode with that ftf?
I got it from your post http://forum.xda-developers.com/showpost.php?p=32978312&postcount=3
Click to expand...
Click to collapse
No, flashmode should always work. Restart phone, restart computer and try again. Make sure you are pressing the very bottom of the volume down button
Try updating via pccompanion.
gregbradley said:
No, flashmode should always work. Restart phone, restart computer and try again. Make sure you are pressing the very bottom of the volume down button
Try updating via pccompanion.
Click to expand...
Click to collapse
I did all of them more than once except using PC Companion. Thank you.
I will not use this tool, because it's not my favor to re-install the halo hd gui and moving other tools via root explorer. I'll wait for OTA, if vodafone germany will rollout 7.0.A.3.195 via ota.
If not, I'll see and look further. But I explain, this has been my first and also my very last Sony Smartphone.
thanks again.
thread may be closed.
harowa said:
I did all of them more than once except using PC Companion. Thank you.
I will not use this tool, because it's not my favor to re-install the halo hd gui and moving other tools via root explorer. I'll wait for OTA, if vodafone germany will rollout 7.0.A.3.195 via ota.
If not, I'll see and look further. But I explain, this has been my first and also my very last Sony Smartphone.
thanks again.
thread may be closed.
Click to expand...
Click to collapse
You give up too easily.
Uninstall flashtool and all sony software from your PC and reinstall.
Also, you can make a backup of your system using recovery and flash your /data back in recovery after you have sorted the problem.
Personally, i will never get another phone other than sony.
gregbradley said:
You give up too easily.
Uninstall flashtool and all sony software from your PC and reinstall.
Also, you can make a backup of your system using recovery and flash your /data back in recovery after you have sorted the problem.
Personally, i will never get another phone other than sony.
Click to expand...
Click to collapse
Thanks again, I am familiar with CWM. I used many different roms with my Galaxy S1 and later with my SIII, too.
With Samsung flashing firmware / custom roms is much easier then with Sony Xperia.
I installed all the needed stuff on an other computer I have in my household and voila it works.
I flashed the rom without wipe data and it works, still without root.
After unlocking boot loader and flashing the V4 comes the shock: all my apps are gone and I have to re-install all my stuff, accounts, gui and so on. I hate that work. Okay, Titanium Backup helps, but it costs many time to get back that system I have had previously.
CWM is a great thing to flashing ROMs and kernels, too. Also great if you want to restore an full image, but to restore (user) data often Titanium Backup is the better choise. But that are only my two cents.
harowa said:
Thanks again, I am familiar with CWM. I used many different roms with my Galaxy S1 and later with my SIII, too.
With Samsung flashing firmware / custom roms is much easier then with Sony Xperia.
I installed all the needed stuff on an other computer I have in my household and voila it works.
I flashed the rom without wipe data and it works, still without root.
After unlocking boot loader and flashing the V4 comes the shock: all my apps are gone and I have to re-install all my stuff, accounts, gui and so on. I hate that work. Okay, Titanium Backup helps, but it costs many time to get back that system I have had previously.
CWM is a great thing to flashing ROMs and kernels, too. Also great if you want to restore an full image, but to restore (user) data often Titanium Backup is the better choise. But that are only my two cents.
Click to expand...
Click to collapse
If you read the whole of the instructions from the SOny site about unlocking the bootloader it clearly states that all data will be lost and that you should make a backup of it.
Certain content on your phone may also be inaccessible due to the removal of DRM security keys and the secure user data partition while unlocking the boot loader. We advise you to create backups, since user data, settings and accounts will be removed.
http://unlockbootloader.sonymobile.com/unlocking-boot-loader
Click to expand...
Click to collapse
First one is: Can't drag and drop ftf file's in Flashtool.
Seccond can't get the phone in flashmode/Fastboot mode.
Light flashing bleu, but no reaction.
On windows 7 all was fine.
I hoop somebody knows the anwsers.
Re: Few problems with Windows 8
Please search before posting. The driver issues with Windows eight had many threads about it. It's a Windows problem not a phone problem. You need to install the drivers via safe mode on your pc
Sent from my LT30p xda premium app.
How do I customise the signature on xda premium app?
With Windows 8 to install the drivers you must search for "Advanced Startup" (Or you can keep down shift and then press reboot), then I think you go to "Advanced Options" then "Windows Start up Options"
Once you have done this your PC will reboot, select "Disable driver signature enforcement"
Then Installing drivers should work (It did for me)
I might have missed some stuff out, I did this from memory, I now have Ubuntu.
Windows 8 drivers are working now so thank you both for that.
But still can't drag and drop ftf files in flashtool.
And can't find the answer onxda.
Notopic1 said:
Windows 8 drivers are working now so thank you both for that.
But still can't drag and drop ftf files in flashtool.
And can't find the answer onxda.
Click to expand...
Click to collapse
Which version of flashtool have you got?
Its been inoperatin for quite a few versions now and should say in the open window that you can drag and drop ftf files here for flashing
I'm on the newest version Flashtool Version 0.9.10.1.
Should i try a older version?
Notopic1 said:
I'm on the newest version Flashtool Version 0.9.10.1.
Should i try a older version?
Click to expand...
Click to collapse
No,
Can you tell me the name of the file (With extension) you are trying to drop in and exactly where are you trying to drop it
I'm trying to drag and drop a ftf file in the middele of the flashtool screen.
Xperia T_9.1.A.0.489_Europe.ftf
Just like normal on windows 7 it all workt.
Notopic1 said:
I'm trying to drag and drop a ftf file in the middele of the flashtool screen.
Xperia T_9.1.A.0.489_Europe.ftf
Just like normal on windows 7 it all workt.
Click to expand...
Click to collapse
Very strange, what does flashtool do/say when you drop it in?
Nothing thats the problem.
Device is connected
- INFO - Device connected in flash mode
But can't do anything.
I can get in fastboot, and flash a boot.img.
But the rom (.zip) is not working and backup is broke somehow.
And dont know how i can't get in the sd card.
As i dont got a cardreader for it.
Notopic1 said:
Nothing thats the problem.
Device is connected
- INFO - Device connected in flash mode
But can't do anything.
I can get in fastboot, and flash a boot.img.
But the rom (.zip) is not working and backup is broke somehow.
And dont know how i can't get in the sd card.
As i dont got a cardreader for it.
Click to expand...
Click to collapse
?
Are you trying to drop a FTF file or .zip file? Flashtool wont work with a .zip only ftf. If the ftf is in a .zip you need to extract it first.
secondly,
You can attach the phone to the PC via usb cable and get access to the sd card via windows explorer, you can just copy it over that way if its a .zip to be flashed in recovery
In flashtool only ftf file's afcorse.
But i realy can't get in the sd cart via windows.
Becouse the phone wil not boot.
I only see a grey triangle.
I can't get it to work.
Notopic1 said:
In flashtool only ftf file's afcorse.
But i realy can't get in the sd cart via windows.
Becouse the phone wil not boot.
I only see a grey triangle.
I can't get it to work.
Click to expand...
Click to collapse
OK, thats normal, just leave the phone plugged in, I had to leave mine for quite a while. It will boot eventually
And you do not have to just drag and drop the ftf file, you can always browse for it.
Click on the flash button, click flashmode then naviagte to the folder where you have the ftf using the dialogue box that opens up.
Ok flashtool is working when i brows for it.
Now i did relock te bootloader, so i can repair it with pc companion.
But now it stil wont boot and the phone is not reconised bij windows or Pc companion.
Stil grey triangle.
I realy dont know how i can fix this.
How long must i wait?
Re: Few problems with Windows 8
Press power & volume up until the device vibrates 3 times (without any cable attached) start up SUS (Sony update service(download of you don't have it )) and follow on screen instructions, or use flashtool to flash a stock ftf.
Sent from my Xperia LT30p using XDA Premium app.
Did I help? Then please press the thanks button
Hello,
I have some problems trying to flash my XZ. I'm using Xperia Flashing Tool 0.9.10.2 beta6 on Windows 8 x64 and whenever I try to flash my XZ flashing tool "gets stuck at "Device connected in flash mode" message after which it gets reconnected and if I try again same thing will happen.
So my question is, am I doing something wrong and if so, please advise.
Bluffer said:
Hello,
I have some problems trying to flash my XZ. I'm using Xperia Flashing Tool 0.9.10.2 beta6 on Windows 8 x64 and whenever I try to flash my XZ flashing tool "gets stuck at "Device connected in flash mode" message after which it gets reconnected and if I try again same thing will happen.
So my question is, am I doing something wrong and if so, please advise.
Click to expand...
Click to collapse
have you correctly installed the drivers for it, connect phone in flashmode and does windows drivers load, also in flashtool go to devices>conected devices and what does it say
Maddhouse said:
have you correctly installed the drivers for it, connect phone in flashmode and does windows drivers load, also in flashtool go to devices>conected devices and what does it say
Click to expand...
Click to collapse
I think drivers are installed fine. Screenshot is below.
no doesnt look it, under ADB devices there is no device, Reinstall drivers and try again. Try the way in my sig for win 8
Unfortunately same thing happens - check screenshot below.
Bluffer said:
Unfortunately same thing happens - check screenshot below.
Click to expand...
Click to collapse
thats better you now have a ADB device installed, you should now be able to put your phone into flashmode
power off your phone with usb diconnected, hold vol down and reconnect turned off phone to usb and you should now get green led and flashtool will say device connected in flashmode but you only have about a min in flashmode before phone reboots
Thank you for your help and effort but even now it keeps disconnecting device. I don't know where the problem is, maybe I'm not doing something as I should.
This is the procedure I was trying:
1) I select Flash device in flash tool
2) I select Flashmode mode
3) I choose which firmware to flash and click Flash so flash tool can start it's magic
4) When flash tool shows message that I can remove my device from USB and turn it off I do so
5) I also press volume down and reconnect the device with the PC.
6) Problem happens here
what about if flashtool isnt ready to flash file, does flashtool pick it up (4 and 5)
it will say device connected in flashmode with green led
Yeah, it does pick it up and displays a message "Device connected in flash mode" and after awhile "Device disconnected".
Bluffer said:
Yeah, it does pick it up and displays a message "Device connected in flash mode" and after awhile "Device disconnected".
Click to expand...
Click to collapse
good yer i think its about a min, now try and download another FTF file
part 1
part 2
that works i have got loads of people to flash that
edit: i made it so its self extract version then there is a FTF file for flashtool
As you suggested the problem was in faulty FTF. It's working like a charm now!
Thank you once again!
Bluffer said:
As you suggested the problem was in faulty FTF. It's working like a charm now!
Thank you once again!
Click to expand...
Click to collapse
Good Good, What wasnt helping was you didnt have drivers installed aswell, now you just have to root and your sorted :highfive:
hey i m having same with my x8 after i accidently kept stock rom for nalf kernal... nw i m nt able to open cmw in phone...plz help..
I am in an awkward situation.
xperia z, 4.2.2 244 rooted stock rom, bootloader locked, usb debug mode off, recovery not installed.
I accidentally corrupted build.prop and the phone bricked.
I cannot use flashtool to flash the stock rom back because usb debug mode is off.
I cannot use Sony update service Pro to force update because it said that "your phone already has the latest available software installed".
I cannot use PC Companion to repair because the software said that "Sony update engine doesn't have software available for your phone".
Please help.
wmiswm said:
I am in an awkward situation.
xperia z, 4.2.2 244 rooted stock rom, bootloader locked, usb debug mode off, recovery not installed.
I accidentally disrupted build.prop and the phone bricked.
I cannot use flashtool to flash the stock rom back because usb debug mode is off.
I cannot use Sony update service Pro to force update because it said that "your phone already has the latest available software installed".
I cannot use PC Companion to repair because the software said that "Sony update engine doesn't have software available for your phone".
Please help.
Click to expand...
Click to collapse
Use PC companion but try use repair phone not update. Wait till all phone model showing up than choose your model phone. btw, your phone must off.
than follow instruction there... wil take 1~2 hour for repair.
Hope you can solve your problem. ill take screen shoot when im home later than post here..
Sent from my C6602 using xda premium
YudiA1 said:
Use PC companion but try use repair phone not update. Wait till all phone model showing up than choose your model phone. btw, your phone must off.
than follow instruction there... wil take 1~2 hour for repair.
Hope you can solve your problem. ill take screen shoot when im home later than post here..
Sent from my C6602 using xda premium
Click to expand...
Click to collapse
Thank you very much for your reply. But I am already using the PC Companion repair option, and the response is as stated above.
flashtool is all what you need,read the instructions
http://forum.xda-developers.com/showthread.php?t=2240614
Sent from my C6603 using xda premium
Reply
wmiswm said:
I cannot use flashtool to flash the stock rom back because usb debug mode is off
Click to expand...
Click to collapse
You can use Flashtool to flash stock rom, doesn't matter if usb debug mode is on or off (only needed to install recovery or to root)
Download stock rom, install flashtool + drivers and follow screen instructions.. Good Luck! :good:
J have the same problem, yesterday j installed cyanogenmod, now xperia Z was on SONY logo and j can't flash original firmware on flashtool, j can only flash original kernel, but is still on sony logo
SUS says that hasn't new firmware for my phone.
What can j do ????
Thanks in advance
gm007 said:
flashtool is all what you need,read the instructions
http://forum.xda-developers.com/showthread.php?t=2240614
Sent from my C6603 using xda premium
Click to expand...
Click to collapse
many thanks, done.
shysparrow said:
You can use Flashtool to flash stock rom, doesn't matter if usb debug mode is on or off (only needed to install recovery or to root)
Download stock rom, install flashtool + drivers and follow screen instructions.. Good Luck! :good:
Click to expand...
Click to collapse
yes, you are right. Yesterday I check everything on the right panel and it does not work. Today I leave all option unchecked and flash properly. Many thanks anyway.
maxam73 said:
J have the same problem, yesterday j installed cyanogenmod, now xperia Z was on SONY logo and j can't flash original firmware on flashtool, j can only flash original kernel, but is still on sony logo
SUS says that hasn't new firmware for my phone.
What can j do ????
Thanks in advance
Click to expand...
Click to collapse
Just follow the flashtool instruction and re-flash the stock rom first, everything will return to unroot stated. Reroot then and try again.
wmiswm said:
Just follow the flashtool instruction and re-flash the stock rom first, everything will return to unroot stated. Reroot then and try again.
Click to expand...
Click to collapse
Maybe j have other kind of problem, j tried with flashtool but it doesn't start flashing when in flashmode, after a minute phone boots itself continuosly on sony logo.
j tried several times with different PC and different ftf file.
j hope to solve this problem, but how...
maxam73 said:
Maybe j have other kind of problem, j tried with flashtool but it doesn't start flashing when in flashmode, after a minute phone boots itself continuosly on sony logo.
j tried several times with different PC and different ftf file.
j hope to solve this problem, but how...
Click to expand...
Click to collapse
Try this way bro.. Done in many Xperia here..
Solving Bootloop phone/Flash Tool can't Detect your phone.
Your Phone Must Off!! and not connected !!
1. Open Pc Companion
2. Click update on Red ellipse (in Picture 1)
3. Start on Phone/tablet Update (in Picture 2)
4. Click Repair on Next Screen
5. in Next Screen, Read that warning Click Continue if you OK
6. Next Step click on Red Circle than Next...
7. Wait initializing Software (10~30 mnt) or depend your ISP speed
8. After initializin9 All Xperia Phone List Will Show Up.
Choose What Xperia Phone Will you repair ( I choose XZ) than Next..
9. Follow instruction On picture.
( Connect USB on your Phone while Press Vol down )
10. if not Start.. Unplug usb and try plug again ==> same no 9)
11. After start.. Waiting 1~2 Hours till done.
(Read Warning There )
Sent from my C6602 using xda premium
YudiA1 said:
Try this way bro.. Done in many Xperia here..
Solving Bootloop phone/Flash Tool can't Detect your phone.
Your Phone Must Off!! and not connected !!
1. Open Pc Companion
2. Click update on Red ellipse (in Picture 1)
3. Start on Phone/tablet Update (in Picture 2)
4. Click Repair on Next Screen
5. in Next Screen, Read that warning Click Continue if you OK
6. Next Step click on Red Circle than Next...
7. Wait initializing Software (10~30 mnt) or depend your ISP speed
8. After initializin9 All Xperia Phone List Will Show Up.
Choose What Xperia Phone Will you repair ( I choose XZ) than Next..
9. Follow instruction On picture.
( Connect USB on your Phone while Press Vol down )
10. if not Start.. Unplug usb and try plug again ==> same no 9)
11. After start.. Waiting 1~2 Hours till done.
(Read Warning There )
Sent from my C6602 using xda premium
Click to expand...
Click to collapse
Solved...j know that phones must be off, the problem was flashtool, j used other version (beta 4) on other pc running xp instead of win7 and all goes good.
Thanks to all for helping me
Doesnt work.
I cant use flashtool, period.
Are there anyother methods?
theVenerable said:
Doesnt work.
I cant use flashtool, period.
Are there anyother methods?
Click to expand...
Click to collapse
The above didn't work for me because I received error based on my type of phone.
This guide however did help: http://forum.xda-developers.com/showthread.php?t=2240614
I had to reboot windows to a settings to enable unsigned drivers. Installed Flashtool and it's drivers,
First unlocked the bootloader(BLU button, got the IMEI, used the sony form (http://unlockbootloader.sonymobile.com/instructions))
Then I downloaded the stock sony xperia z ftf image, placed it in Flashtool's firmware folder, then flashed it (flash device > flash mode).
Now my phone's working again.
HTH,
George
brick,unbrick,xperia z problem,flashtool
My OS phone in recovery mode (root) got deleted And when I turn on phone stuck on Sony logo And when it is connected to the computer showing error your USB not recognized and Flash mode for use Flashtool doesn't work and the same error shows what should i do?
shayanster said:
My OS phone in recovery mode (root) got deleted And when I turn on phone stuck on Sony logo And when it is connected to the computer showing error your USB not recognized and Flash mode for use Flashtool doesn't work and the same error shows what should i do?
Click to expand...
Click to collapse
If you still can enter custom recovery, you only need flash rom and (with) suitable kernel.
If not, you need Flashtool.
- make sure you have the newest version of flashtool and driver
- connect your phone to pc.
- when computer show error about usb not recognized, go to computer management - device manager. Find something in universal serial bus controller list that have yellow triangle and exclamation mark. right click and remove it
- disconnect your phone then reboot your pc
- install flashtool and driver, reboot pc again
- connect your phone to pc. Now, it should detect your phone.
- do flashing procedure
cmiiw
visualfighter said:
If you still can enter custom recovery, you only need flash rom and (with) suitable kernel.
If not, you need Flashtool.
- make sure you have the newest version of flashtool and driver
- connect your phone to pc.
- when computer show error about usb not recognized, go to computer management - device manager. Find something in universal serial bus controller list that have yellow triangle and exclamation mark. right click and remove it
- disconnect your phone then reboot your pc
- install flashtool and driver, reboot pc again
- connect your phone to pc. Now, it should detect your phone.
- do flashing procedure
cmiiw
Click to expand...
Click to collapse
Thanks for the answer I tried all ways but the problem is not solved .I think the only solution is JTAG box
shayanster said:
Thanks for the answer I tried all ways but the problem is not solved .I think the only solution is JTAG box
Click to expand...
Click to collapse
To use Flashtool put phone in flashmode, it will not work in recovery mode
To put phone in flashmode
Hold power + both volume keys
wait till you feel three vibrations.
Make sure you have installed Z drivers flashmode drivers & fastboot drivers(Setup fille is in driver folder of flashtool)
Keep FTF file in firmware folder of flashtool
Start flashtool
Click the thunder button
select flashmode
select the FTF file
When it tells you to connect phone
Hold volume down key and connect USB it should start flashing
androidtweaker1 said:
To use Flashtool put phone in flashmode, it will not work in recovery mode
To put phone in flashmode
Hold power + both volume keys
wait till you feel three vibrations.
Make sure you have installed Z drivers flashmode drivers & fastboot drivers(Setup fille is in driver folder of flashtool)
Keep FTF file in firmware folder of flashtool
Start flashtool
Click the thunder button
select flashmode
select the FTF file
When it tells you to connect phone
Hold volume down key and connect USB it should start flashing
Click to expand...
Click to collapse
when it is connected into flashmode the computer showing error your USB not recognized
shayanster said:
when it is connected into flashmode the computer showing error your USB not recognized
Click to expand...
Click to collapse
Is it Windows 7 or 8?