Can you tell me how can I pair the phone and a Logitech - Cordless MediaBoard Pro
im trying to pair but neither 0000 and 1234 code works.....
Im on android 2.3.7
What am i doing wrong thanks.
Found this post while trying to do the same thing
I checked the manual for the keyboard, and it reminded me that it was designed for PS3 and not running a normal bluetooth stack, so the pairing process is a little different.
Switch the keyboard off, switch it on, press reset. This makes the keyboard discoverable.
Tell your Android device to look for new devices, find the Mediaboard, try to pair.
Enter 0000 as the pairing code on your android. Then, type 0000[Enter] on the keyboard. You should now be paired.
Your phone should now list the keyboard as "Paired, but not connected" and you'll still not have a working keyboard, but you'll have made as much progress as I've made.
Let me know if you figure out how to connect!
When i try the 0000 it shows error during pairing.....
Related
Hi,
I have a BT keyboard, Think Outiside Stowaway Bluetooth.
When I pair it with my X7500, the pairing passcord is not popped up while other device like my lap top shows a pin code on the screen. Instead, a input box like a BT mouse or a BT headset shows and asking me to input the passcord, which I cannot know.
I tried to install a driver for WM5.0. In this case, the mouse did not work because my mouse is not a product of Think Outside.
I just want to use this BT keyboard together with my BT mouse.
If anyone has a simiar trouble, please help me out.
Thanks,,,,,
the passcode is 0000
Thanks but...
The passcord '0000' does not work.
Could you let me know how to pair my BT Keyborad to X7500?
What I did is as below;
1. add new..
2. select BT Keyboard
3. Passcord textbox comes up
4. type '0000' in X7500
5. No connection message comes out.
Thanks...
Treat it like a 'secure' password connection and after you put in '0000' on the Advantage, put in '0000' on the Think Outside keyboard too.
Brad Miter
You choose your own passcode (you need to use onscreen one to put the first code in) , then type it on the keyboard after that. I got one of these for Christmas and it's a great keyboard!!
Hi,
I have a strange comportment of my Diamond when I try to pair bluetooth devices whitch have pairing code different of 0000.
Everytime I try to give the pairing code of the device (1234, not changeable), the enterred code in cleared when choosing the "next" button.
(assuming then that code is not needed or is 0000).
Has anybody a solution for this problem ?
Diamond is with original firmware from HTC (the one dowmloadable on there site).
Thanks in advance for your answers
Bouhboulle.
More of the same
I have the same problem (posted earlier). My car's hands-free requires a random code provided during the pairing process, and pairing never succeeds. I understand the Diamond tries 'standard' codes - 0000, 1111, 1234, etc. is there a way to disable this?
Me too
The same for me using Diamond from Vodafone with Vodafone 3D touchflo. I can't pair with any BT device. Please help from anybody.
Thanks a lot.
I do not have this issue.
I can pair with any code on laptop. And my carkit (parrot) just pairs perfect with 1234
BUT
When entered the code, just WAIT, and don't fill it in again. I often see the 'code' field again, and want to enter. Pairing twice gives error etc. Just ignore the empty field, when paired it dissapears.
Think its a tiny bug.
Still the same...
Hi Riel.
There is no option to enter the code twice, once you press next automatically deletes the field and acts as an enter.
BUT, surprisingly, I have installed a cooked ROM and the same again... I now have my doubts about the BT application, I think is the original one from the OS and not an cooked accessory.
I hope that anybody reading this could put some light on it as is one of the strangest behaving I've seen around PDAs in many years.
Thanks for any help.
Its strange my diamond works fine with parrot kit but not with my bt kit
anyone knw why,
Here is the solution
Go Start/settings/connections/bluetooth/right down press security tab and uncheck passkey
Doesn't work, for me at least...
turboss said:
Here is the solution
Go Start/settings/connections/bluetooth/right down press security tab and uncheck passkey
Click to expand...
Click to collapse
Thanks for the answer but I have tried and doesn't work. On the screen says this is for infrared connections, or am I lost?.
Cheers.
EDIT: I got it finally but the only way is to flash the original ROM and later the one you like. Also remember that some devices does not support more than one pairing partner, this happened to me with a Nokia BT headset, I had to refresh it.
Good luck.
I can not pair my BT head set i-Tech R35 Clip to my new TD2, i get to the enter password part but they do not pair off. I have put the BT head set in to pairing mode.
Does anyone have any advise to get me paired off.
Thanx and regards
Chris
Pairing BT
there is two places you can pair your topaz with a BT headset.
1) link in comm manager over BT, not the switch part at the far right, but the bar where it says bluetooth. it'll take you to a screen where you can pair a headset.
2) in settings in the conection tab under bluetooth (or comm manager, BT and advanced), which is a multi tab that shows you the deviced paired, connected allow you to be discoverable the ports you created etc...
my point is for headset i have had problems conecting thru the advanced menu (2) but it worked thru the Comm conection, i don't even have to enter the key, it seems like it tryes 1234 0000... so i recommend going to the option 1, and there pairing your headset.
the other thing i noticed is when you pair a device, if you got the wrong key on the first atempt even if you enter the right one after it will not pair, so the solution is pressing back refresh and connect again and then enter the right key.
at least it worked for me
cheers
Timothy
Thanx for your guide, unfortunately it still will not connect. either option 1 or 2. I tried entering the pass code 0000 but it fails to connect and says the pass code was incorrect. If i try the option of no pass code it says it has connected, however the BT headset does not respond with hte usual 5 x flashes of the LED.
I still can not get connected :-(
HEllo all,
I hope someone can advise or help me.
I have a Nokia SU-8W Bluetooth Keyboard which is a very good bit of kit.
It works flawlessly (0 lag) with a Bluetooth Mouse on my N95.
I cannot however get it to PAIR WITH MY HD2
I can find the device, then try to pair, the HD2 asks me to type in 6-7 Characters on the keyboard, which it picks up no problem.
It then says press enter to complete, at which point I get an error telling me that my device is not discoverable.
I have set the device to discoverable and to no discoverable yet this doesnt help.
I have tried with 3 different Radios 2.7.50, 2.7.51 and now 2.10.50 yet still gives me same error. (also stock, Dutty and Energy Roms)
I just want to make it work so I can play System Shock 1 on Dosbox
I really suffering in my Love Hate relationship with my HD2.....
At last my FM radio gives me more than 1/2 a station, and I got Wiimote working on FPSCE so I can play games....now I want dosbox with a keyboard hehe some people never satisfied!
Any advice or experience with this device or similar would be great.
Many thanks all!
Nokia BT Keyboard pairing
Hi, I did it a couple of weeks ago, and in the first place it was also not working for me.
But I have found out, that if it asks you to press the enter on the keyboard, that it is not the real enter on the keyboard. I am not having it with me now, but I managed it to get it paired to my HD2.
I will try to see, what I have done to get it paired, but my keyboard is at home and I am abroad at the moment. Give me some days.
Once you have it paired, it will makes the connection without problems, even if you have the BT as hidden (as i have). Beside that, you have to play with the correct language settings too, before you have the correct keyboard layout.
Remember, it is possible to get it paired
Edit, solution:
Press once (!) the FN key, you will see the (FN) light will light up.
Now, press the numerical code (these are located on top of the QWERTY keys, and they are now enabled because of the FN function).
After you have completed the entering the code, press the (FN) key again, this will switch off the numerical keys and now press enter.
You should have a connection now
Perfect!!
Thank u very much!!
+ 100 rep
Works perfectly. As IT support I should have noticed!
Many thanks
Works peftectly in word etc....
If I try to use it in Dos box.....is not acknowledgeing any key except the return key
I will investigate more!!
yarod_g14 said:
Thank u very much!!
If I try to use it in Dos box.....is not acknowledgeing any key except the return key
I will investigate more!!
Click to expand...
Click to collapse
Sorry, can't help you with that, I am not using a DOS BOX on my HD2
I've got an Apple BT keyboard, and can get it to successfully pair with my Nook, but nothing else. I've tried using BlueKeyboard JP, and it sees the keyboard as well, but when I go to an input window, it says "Connecting, do not touch keyboard...", then after that goes away, its notification message says it's there but disconnected. This is really the last thing I want to get working on my NC before I'm really happy with it, but am kind of at a loss. Any suggestions? Thanks! Oh, and I'm running the latest nightly (160).
I've gotten my Apple BT Keyboard (came with my iMac) to pair, but keyboard does nothing.
(do not pair with a CM modded phone, causes the phone to bootloop unless you keep the keyboard far far away from it or disable bt on the phone or poweroff the keyboard etc.)