Is there any programme to for screen calibration? So part of the screen seems not responsive.
That is a hardware issue not a Calabration issue..
does somebody know if this "hardware issue" is present at all note's?
i found that my screen is a bit unresponsive at the top right corner. i cant draw about 2mm to the border of the screen (with the pen)!
lolcat12 said:
That is a hardware issue not a Calabration issue..
Click to expand...
Click to collapse
However when I flash a new rom the screen get responsive for a short while. After that I need to press the screen harder. On the bottom right hand corner has this problem.
helmetbox said:
However when I flash a new rom the screen get responsive for a short while. After that I need to press the screen harder. On the bottom right hand corner has this problem.
Click to expand...
Click to collapse
Did you ever solve this problem? Mine started doing it after it updated KL7 OTA.
Well guys I'd like for someone to chime in on this. I thought for sure this was a hardware issue. I'm on my second note now. My first note seemed like it was having issues with the lower right corner of the touch screen. I thought maybe it was a rom issue. I flashed clean KL7 and it seemed to suddenly be better then after a little bit it got worse. I have my second note and I flashed KL7 right away on it. Now after a little bit it seems to be getting less responsive, still better than my first, but I'm beginning to think this is a software issue. Any of you having these issues what Rom are you on? Should I try changing out this note for a third and see what happens? I may flash to some other firmwares to see too.
my top right is a bit unresponsive as well. . it works but seems a bit off. .
I used swipepad , really useful taskswitcher
It does not work when phone is connected any charger.
I've definitely noticed the phone being less responsive when on the charger, but this seems to lose responsiveness over time off charger and on battery.
I've had other phones that from time to time would act a little wonky when using them while charging.
Hey,
I've had some display problems, both with regards to calibration and also when it's charging.
I have made this video to demonstrate a problem I have of calibration. Watch how the display detects a signal at a point offset from where I press with the pen.
For me the problem I saw using the *#*#2664#*#* test is that the last 10 pixels or so on the 2 end sides of the screen don't respond.
For the pen offset is cause of the left or right handed settings, I find that holding the pen and rotating it so that my thumb presses the button of the pen instead of the indicator finger gives pretty good accurate results.
I'm definitely thinking this is at least more software related than hardware. I don't remember noticing any problems when on KJ1 or KK1. So I flashed back to KK1. It started it up and then I did a quick factory reset. This is completely stock/unrooted. Anyway bottom right corner seems to be having no problems detecting my touch now. I'll leave it on this for a few days and play around and see if it seems to lose sensitivity again. If it does I'll let you guys know, but for this to be a hardware problem I can't imagine it being this intermittent. Any of you on KL7 that mentioned this issue, are you guys completely stock KL7 or using the CF-Root Kernel? I know someone mentioned losing functionality in music player and torch and it seemed to be an issue with an alternate kernel.
trumpetboy101 said:
Hey,
I've had some display problems, both with regards to calibration and also when it's charging.
I have made this video to demonstrate a problem I have of calibration. Watch how the display detects a signal at a point offset from where I press with the pen.
Click to expand...
Click to collapse
That´s normal - pen is calibrated to use it at a certain angle - try to change the setup from right handed to left handed and you will see a different offset if you make the same test again.
The offset should be the same on each area. Only if this is not the case i would say, there is an issue with the screen.
Hey, ok so it is a deliberate software decision. Kinda sucks- I'd think I'd sooner like to have it type directly below where I write. I'm guessing it is an attempt to account for the fact that the glass has a finite thickness. Sooooo does anybody fancy writing a kernel alteration for this...?
i also find it more annoying than useful
Couple days on KK1 and what I thought was a hardware problem still seems to be fine. It's detecting much better in the bottom right corner where I was having issues on KL7.
I am having the same issue with the reduced responsiveness of the bottom right corner. I've noticed it after updating to KL7. Maybe is the driver of the screen.
Is there any way we could report this back to Samsung?
Sent from my GT-N7000 using XDA App
Hello.
I have the same problem ate bottom right side of the screen. I am ate LA4.
what should I do?
Although the problem was nearly imperceptible some days ago, while the note was connected to the charger, I've noted a very small area near the bottom right side of the screen where it was difficult to write using the stylus with SMemo. On the opposite side the loudspeaker is present; and so I've thought it might be correlated with the magnetic field of the loudspeaker. Today I've performed the *#*#2664#*#* test with and withouth the charger, but the problem is not occurred. Because of these devices are always more complex I prefer snap closures for my cases.
Related
Hi there,
I love my diamond, but I have one problem. The 'Home' side of my buttons at the bottom of my diamond seems raised higher than the 'Back' side, the 'Home' corner in particular. As a result, in the dark, I can see the white LED shining through a small 'crack'. It's not a huge problem, I just wondered if others have the same issue.
Thanks.
Same here.....doesn´t bother me a bit, though......
Anyone else? I assume this is just part of the build then. Perhaps there is something extra 'packed' under the left hand side...
I noticed the same thing almost immediately myself, but believe this may actually be a "work as designed" thing. It could simply be a difference of what is under the touchpad on one side vs the other.
In my case, I was happy to have gotten a phone with a "calibrated" G-Sensor, so I was not about to change it because of this...
Mine has a slight "crack" on the left side where the backlight is shining through but its not higher than the right side. Not bothered too much as I'm happy with my calibrated G-sensor so not gonna bother changing it.
kien said:
Mine has a slight "crack" on the left side where the backlight is shining through but its not higher than the right side. Not bothered too much as I'm happy with my calibrated G-sensor so not gonna bother changing it.
Click to expand...
Click to collapse
I am currently waiting to hear back from Orange regarding my 'slightly off' G-sensor. It's not off by loads, just slightly. They say they are in talks with HTC currently regarding a solution. They have a list of people with the problem. They said to either expect a software update (not sure what good that would do, although if they uploaded some sort of calibration tool it would be good), or a text telling me to call them to discuss the matter further. That was on Friday, and they said a response would come in 5-7 days...
hey guys,
having said that I tried a lot of methods such as the "automatic recalibration"..I really can't believe that we don't actually have a specific app for recalibrate our big touchscreen..it's so annoying when you put the S-pen on the screen and you see the pointer with 3-4 mm offset.
I'm running ICS Stunner 4.3
If my pen has an offset all I need to do is to wiggle the pen in each corner at the edge of the screen for a few seconds (like drawing small circles over eachother) and the offset is gone.
are you on stock rom? cause I'm not..and I think this is why it doesn't work for me.
I'm using Rocket Rom V23 with SpeedMod kernel 2.8.
The thing I've noticed is it depends on the app I'm using, it seems that the stock Samsung pen apps all use a small offset while the pen is way more accurate in Infinite Painter.
When my pen offsets I rotate the screen to portrait then back to landscape(or the other way around) and it usually sits bang on again.
Hi mates
Few days ago I've encountered a very annoying problem while using s pen
When I'm using s pen in whatever app (S note, iAnnotate, Adobe Reader...) I'm encountering offsets in whatever direction. Most often to the right side of the screen. S pen touches the screen, but the line appears 3mm to the right and a little down.
When I'm using hand no problem occurs!
But when I'll run Crayon physics and using s pen. No such thing as offset occurs!
WTF?
Have anyone of You guys encountered such thing? How can it be solved?
To be honest, I'm getting nervous more and more :/
I'm on:
- stock, non rooted ROM;
- system version 2.3.6, kernel 2.6.35.7;
- version: GINGERBREAD.XXLC1;
- modem version N7000XXLB2
I know this sounds obvious but did you try changing Pen settings from Left handed to Right handed / back again in the dominant hand settings? Someone reported that this seemed to rest the offset. Personally I found if I rotated to landscape and back again it seemed to be better, but never really had a problem.
Sure I did mate. Didn't help me to much :/
I've also tried to rotate to landscape and portrait - it helped, but only for a little while.
What is strange for me is that this kind of issue appears in apps and in keyboard while I'm on s pen, but never while playing in Crayon.
And I've played a lot today. And without any offsets
If also in game I would have encounter problems, then I might have start thinking that this issue is caused by damaged s pen or the screen itself.
I was also thinking for a while that it's caused by software I've installed. And I have a lot.
Now I'm using sslauncher and LWP - Galaxy Pack. Those are my two types.
But it's also rather impossible for me that some apps can influence on s pen behavior in general, but not in game?
Does anyone have issues with the touchscreen skipping every once in a while? Occasionally, there is an area on the lower half of the screen that seems to be insensitive, but if you start touching around it, it goes back to normal.
I've discussed this with some fellow Z1 owners and it appears to be a relatively common issue. There is some discussion that it may be due to overheating or a software issue.
Anyone else have this problem?
Had this once while my device overheated hard(~47-48°).
Not sure if I have to be concerned about that, because otherwise it works fine.
koopa101 said:
Does anyone have issues with the touchscreen skipping every once in a while? Occasionally, there is an area on the lower half of the screen that seems to be insensitive, but if you start touching around it, it goes back to normal.
I've discussed this with some fellow Z1 owners and it appears to be a relatively common issue. There is some discussion that it may be due to overheating or a software issue.
Anyone else have this problem?
Click to expand...
Click to collapse
Same here
Sent from my C6903 using XDA Premium 4 mobile app
At first I thought it was an issue with crappy screen protectors. The Z1 already has a anti-crack film on the screen so I thought that adding a poorly made screen protector would create too much distance from my touch to the sensor. However, I've tried replacing the screen protector and also asked other people with varying brands of screen protectors and it seems that the issue still persists.
The issue seems to occur most often on the password screen for me (which is particularly annoying).
I've had it too, lower half of screen does not register slides on login screen for a brief moment.. No overheat!
Sent from my C6903 using Tapatalk
No overheat here 2 but with the same issue.
Also the last days i think that all the screen sometimes is more insensitive than usual.I have to touch 2-3 times to do what i want.
I think that is a hardware issue.
Have it sometimes as well sadly! Can't figure out when exactly it's happening though..
I find it very annoying when I'm scrolling and at the bottom part of the screen, the scrolling becomes a click, which brings me to a place I did not intend to go to. Hope it's software, but can't imagine that.
Happens to me as well, regardless of device temperature. Based on the seemingly random nature of the issue, it should be a simple fix via software update. A similar bug persisted on the 2013 Nexus 7 devices when you laid them flat on a surface.
koopa101 said:
Does anyone have issues with the touchscreen skipping every once in a while? Occasionally, there is an area on the lower half of the screen that seems to be insensitive, but if you start touching around it, it goes back to normal.
I've discussed this with some fellow Z1 owners and it appears to be a relatively common issue. There is some discussion that it may be due to overheating or a software issue.
Anyone else have this problem?
Click to expand...
Click to collapse
Same problem here!!!
I think is a hardware issue. When you touch the alu frame the phone works fine. If the phone is on the table or in a cover the issue are immediately there.
Sorry for my bad english. Hope you understand
I noticed some small things and thought it was me but I guess this makes sense.
Could be worse, my previous Note 3 had multitouch issues and had problems register several fingers :silly:
Considering how common the issue appears to be, I find it hard to believe that this is a hardware issue.
I also don't believe it's related to overheating since it seems to happen even when I haven't used the phone at all for a long time.
It feels like a software issue to me since the issue sends to go away if you touch another section of your screen
koopa101 said:
Considering how common the issue appears to be, I find it hard to believe that this is a hardware issue.
I also don't believe it's related to overheating since it seems to happen even when I haven't used the phone at all for a long time.
It feels like a software issue to me since the issue sends to go away if you touch another section of your screen
Click to expand...
Click to collapse
When you touch the alu frame the issue is not there. Only when you use phone without touching the frame.
Must be some kind of hardware issue...
Sent from my iPad using Tapatalk HD
I am having the exact same issue. The weird thing is, is that it doesn't always fail to register my finger. I've gone a few days without it, then suddenly it's back again. Also in the Xperia Diagnostics app I could then see the phone failing to register a proper line, then 20 seconds later it's gone. Weird thing indeed.
Sent from my C6903 using XDA Premium 4 mobile app
nonamedk said:
When you touch the alu frame the issue is not there. Only when you use phone without touching the frame.
Must be some kind of hardware issue...
Sent from my iPad using Tapatalk HD
Click to expand...
Click to collapse
Is this the case? I don't think I've ever used my phone without touching the frame somehow.
koopa101 said:
Does anyone have issues with the touchscreen skipping every once in a while? Occasionally, there is an area on the lower half of the screen that seems to be insensitive, but if you start touching around it, it goes back to normal.
I've discussed this with some fellow Z1 owners and it appears to be a relatively common issue. There is some discussion that it may be due to overheating or a software issue.
Anyone else have this problem?
Click to expand...
Click to collapse
Yes, I have it as well.. First of all though, to reply to a lot of people on this thread, it happens regardless of "flat surface, touching the frame, overheating", or anything else. It seems to be completely random with me. Sometimes everything is perfect, then it goes nuts for no apparent reason whatsoever. I'm almost sure it's a software issue, and hope sony will address this issue soon!
it also happens sometimes to me.
the only thing that helps is to touch the ground of the ac power socket. it seems like the screen needs much more potential difference between the pointer and the screen itself and after a while of using it the pointer (you and your fingers) are more loaded.
thats my theory to it.
Jimmyness said:
Yes, I have it as well.. First of all though, to reply to a lot of people on this thread, it happens regardless of "flat surface, touching the frame, overheating", or anything else. It seems to be completely random with me. Sometimes everything is perfect, then it goes nuts for no apparent reason whatsoever. I'm almost sure it's a software issue, and hope sony will address this issue soon!
Click to expand...
Click to collapse
Unfortunately, unlike the rooting camera bug, it doesn't sound like Sony has even acknowledge it at all.
Exactly this.
http://www.youtube.com/watch?v=h0sqwwUoEPc
I often have to attempt inputting my password multiple times before I can finally get it right. I have since switched to PIN unlock. Really wish there was some sort of response from Sony.
I'd you're using pie then stop using it and retry the affected area. I had this issues because of the activation area causing certain keys on the keyboard to become non responsive.
Sent from my Z1.
Has anyone tryed the touchfwtool?
URL itechdestiny.com/xperia-touch-screen-solution-touchfwtools-apk-download/
My phone is on the way back from repair. They only have calibrated the screen.
Starting a new thread since I could not find any existing thread on this and it is quite surprising since this is a widespread issue and for the same reason Samsung service here in Melbourne even refused to acknowledge this is an issue! There logic seemingly being if the issue is present in the demo unit in the store as well, it is not an issue! Vodafone has also refused to honor the warranty, even though it is in the first month of my contract and they should be replacing the handset and dealing with Samsung, and have instead told me to provide them with an acknowledgement from Samsung stating it is an issue! Talk about deadlocks!
Now coming to the issue, I have found out that there are sensitivity issues when using the S-Pen on the bottom right and left corners of the screen. There are issue on the top part of the screen as well but they arent as serious. I would also request you to check the same on your device and report back if you are also facing the same.
To check, first get into diagnostics mode by dialing *#0*# and then go to the S-Pen tab.
1. As you can see in the video, the bottom right and left corners have definite and serious issues with S-Pen sensitivity. I found this out, and it is also a use case and one of the major reasons that I went for Galaxy Note 5, while taking a screen grab from the middle of the screen right until the bottom right corner. I just could not do it. As soon as the S Pen reaches near the corner, the sensitivity issue makes sure that input isn't recognized. Not only this, even when it manages to identify the touch, the tracking is random with the S-Pen having a mind of its own.
2. The second issue is while drawing on the top part of the screen with the S-Pen but this one is not as serious as the first one. You can see in the video that S-Pen loses sensitivity in one particular area of the screen. This is easily corrected though, by pressing the S-Pen harder on the screen.
This is apart from the lag and slowness issues that rear their ugly head every once in a while and in a phone which runs an Octa Core CPU with a whopping 4GB of RAM. This is my first Samsung in a long long time and it has left me disappointed again exactly like it did in the past whenever I bought a Samsung phone. To me the level of polish of the hardware on a device costing as much as this is simply not acceptable. What are your thought? Please report in this thread if you are facing the same issue as I am with the S-Pen.
https://www.youtube.com/watch?v=XN41nE1lWGI
I have multiple stand-alone S Pens and don't experience what you're describing with them or the one included with the device.
BarryH_GEG said:
I have multiple stand-alone S Pens and don't experience what you're describing with them or the one included with the device.
Click to expand...
Click to collapse
Strange because I could replicate it on all the demo devices in the store. That is their reasoning for refusing the warranty as well.
I'll say this, the included pen is more responsive on the display than pens that are pre-Note 5 so something in the pen and/or display has changed.
Does it mean mine has a problem then? I am wondering if anyone else can also confirm the same?
I can confirm the bottom left and right corner of my note 5 behave just like OP's does... but wouldn't have found out if he didn't mention it
alexcarterkarsus said:
I can confirm the bottom left and right corner of my note 5 behave just like OP's does... but wouldn't have found out if he didn't mention it
Click to expand...
Click to collapse
Thanks Alex. I found the issue because I could not take a screenshot which finished near the bottom corner of the screen. Now smart select is a headline feature of the phone and this hadrware oversight to be is just not acceptable. The Samsung service would not acknowledge it as an issue let alone do something about it. May be it is only on the first batch of phone. Who knows?
I checked my phone (SM-N9208 TW, mfg: will add later) and the bottom corners have poor tracking with the hover point flying off the screen when held above.
Overall this issue shouldn't affect the usability of the phone if you rarely use these areas since it's still possible though difficult to use the s-pen there.
Edit: I re-tested with my phone flat and s-pen vertical*. The s-pen can be used on the very bottom corners with precise movements, so I don't think will affect usability for most people most of the time.
*Having the s-pen on an angle can affect the tracking significantly as seen in your video. I think the only solution would be to modify the s-pen to track at the very tip. This would probably make the tip non-replaceable and/or more complex and expensive. If someone has time, try using the s-pen without a tip and see if/how it tracks.
Update: I tested a SM-N920W8 in store and it had the same corner issue.
I complained to Vodafone again and they decided to take the phone back. Back to trusty properly working iPhone 6s Plus 64GB. My last Samsung device no matter what the specs. I wouldn't be interested in one even if it will have a gazillion core CPU and few petabytes of RAM.
I have the same issue. Can anyone else, note 5 users confirm about this issue. (Bottom right hover issue)
I dont't face that problem
Edit: here is a screenshot
https://drive.google.com/file/d/0B5LZ1p_SFZ3faTFJNzBzZGlnbzA/view?usp=docslist_api
Mine does it a little bit.
It still passes the test so I believe it's within spec. I honestly don't see it being a warranty issue.
Sent from my SM-N920T using Tapatalk
Sometimes, it is the Cover magnet.
Sometimes, it is the Cover magnet. . Try to remove you phone from it and try the s pen in the touch area in question. It worked for me with in a leather flip cover. The same for the s note stopping error message.
same here
SM-N920C cihazımdan Tapatalk kullanılarak gönderildi
if you have magnetic casing will get such problems ....
or fake s-pen need to replace with original or better fake quality
My stylus is overly sensitive; so much that I can't write properly. All text is in continuation even when I lift the stylus off for whitespace. I even followed the article on adjusting the sensitivity of the S Pen by removing the click-button cover and adjusting the Potentiometer. However, the note 4 s pen is entierly different as it doesn't have any Potentiometer under the click button. Link to article:
http://forum.xda-developers.com/showthread.php?t=2191333
What annoys me most is that I never had this issue before I flew overseas last month. I started experiencing this issue after I came back and it has rendered my s pen useless. Has anyone found a way to adjust Potentiometer on the new S spen yet (it might be located under top cap but i'm not sure how to open it).
espionage said:
My stylus is overly sensitive; so much that I can't write properly. All text is in continuation even when I lift the stylus off for whitespace. I even followed the article on adjusting the sensitivity of the S Pen by removing the click-button cover and adjusting the Potentiometer. However, the note 4 s pen is entierly different as it doesn't have any Potentiometer under the click button. Link to article:
http://forum.xda-developers.com/showthread.php?t=2191333
What annoys me most is that I never had this issue before I flew overseas last month. I started experiencing this issue after I came back and it has rendered my s pen useless. Has anyone found a way to adjust Potentiometer on the new S spen yet (it might be located under top cap but i'm not sure how to open it).
Click to expand...
Click to collapse
I am having this same problem. Did you ever find a fix for it? Thank you!
Yes confirmation of problem
I found the same problem. If you try to draw a square in the S pen test mode you cannot draw a square in the bottom left or right corner. The square will turn into some kind of strange wiggle shape.
I live in Malaysia and went to the official Samsung head office service center and they confirmed this is a problem with all Note 5 models and the lady showed me her own personal Note 5 which had the same problem (actually worse than mine).
The service technicians said they do not know the reason for this problem. But as an electrical engineer I suspect there is some sensors in those areas which cause interference with the S Pen.
I've bought an Xperia Z3+ two months ago, recently, I've discovered a certain bright spot on its screen, it's particularly available in white and bright backgrounds, it's less noticeable in black backgrounds, and not at all noticeable in non-solid backgrounds.
I know that it's a hardware issue, but the warranty here is a joke, and I don't want to pay for a new screen for such a small issue.
But on the other hand, once I noticed it, it's all I could see in the mobile, and it removes the whole premium feel in it.
I've manually removed the back cover and there's no issue in the battery that would make it press towards the screen and cause such issue.
I was wondering if there's any manual fix for it? I know that it's a light diffusing layer problem, mostly caused by a certain pressure, but is there a way to make it normal again? A certain pressure in an opposite way, or heat, or suction from behind, etc.
Here's a picture that indicates the issue "It's more visible and annoying in real life"
I have the exact same problem at the very same position as you point. My country does not support officially the Z3+ and so the cost is really high. I searched enough on the internet and i think it is where the vibration is but i cannot confirm it. I also see it all the time because i simply know it is right there. At my case, there are other 2 spots but not seen so easy.
I only hope not to get bigger. I wish i knew what caused this so to be carefull (such as sun exposure or something else - although i am REALLY careful as a person with my mobile phones). I cannot help you and i got really dissapointed after my long search on the web so i will have to live with that. It is hardware problem as i really tried everything to find out that.
Hope someone has any solution. It is not only on our phone but to others too. I hope the post won't get lost after some days!
AntwnisGr said:
I have the exact same problem at the very same position as you point.
Click to expand...
Click to collapse
That's so weird, I thought it was caused by an anonymous fall that I wasn't aware of, the other point is barely noticeable but it's at the top left.
Also, my upper speakers started to produce mixed loud and faint sounds when i play something whike the volume is below 25%.
It's winter, and I usually text near heatrrs, which made me think that the speakers problem was caused by the heater and the screen problem was caused by a particular fall.
Since the warranty is useless I've manually disassembled the phone and there's nothing behind that spot of screen except battery, the vibrator is way below the navkeys, there's no screen on the other side of it, which actually seems to prove that our spots are similar by coincidence, because there's no pressure on the other side except for battery, and I highly doubt yours is faulty, because mine isn't.
My z3+ single sim also has the spot at the same place, but it isnt that noticable since i use auto brightness, really weird, i thought because maybe of accidental high press when the phone was in my pocket.Anyway, I'll switch to XZ premium in december, that sh*t is dope
On the top left corner i have too! So it is not a coincidence. Something is there that you couldn't see when you opened it. I only hope it doens't get worse..
I have it too not only there also in the right bottom corner and a line of 1 centimeters like 1 inch bow in the left upper corner one day was not in there and to the other plaff they appear
Sent from my E6533 using XDA-Developers Legacy app
Now that multiple people have it, I started to suspect that there's actually something.
I might open if again when I can't live with it anymore, but for now I'll try to enjoy it as it's new, and hopefully won't get worse.
I have a z3 and z4 that also have these white spots..no way to fix. look up tv lcd problems your not gonna be able to fix....it gonna keep me from buying anymore sonys till they switch to oled.
I have the same problem in the same position and it was happen after a warranty repair.... Sony didn't have noticed it....