Database Develop

Diamond wont charge with dead battery

Nightmare.
Got my Diamond today, and charged it up.
It ran out 5 minutes ago, so I plugged it into the mains charger.
It vibrates, shows HTC and then gets stuck in a constant reboot. It's like it gets a little charge, uses it, then restarts the process.
I guess the battery is so dead that even the mains charger cant give it enough boost to start charging.
Help Please

If you only got it today then id be sending it back as it seems to be a faulty unit. Perhaps someone can give you a fix but if it was me, id be demanding a new working unit...you just never know what other faults the phone might have.

Good job I didn't Hard-SPL it straight away.
Damn, Always happens to me.

Are you trying to charge it with the wallcharger or by usb to a computer.
Beacuse if you are doing it by the computer there is an option on the phone that disables charging when conected to the computer.
Good luck dude.

Definately wall charger.
I think it's f(***d
I'll go back to my Kaiser and wait for the Raphael I think.

i would first try to charge the battery device turned off!
i noticed that the led in center button does not blink in the beginning but it should charge!
after a while try a hard reset!

Tried the following:
I cant switch off the device as soon as power is applied via USB it switches on. Tried holding the power button down but nothing.
Tried entering bootloader but same reset loop.
Tried hard reset, gets to grey screen with blue text but then reset loop again.
I tried leaving the battery out for half an hour and trying again but soon as usb is in it powers up and reset loop.
I put a multimeter on the battery and it is dishing out 3.7v as expected.
I think the device is knacked, even though I was using it for most of the day.

laporte said:
i would first try to charge the battery device turned off!
i noticed that the led in center button does not blink in the beginning but it should charge!
after a while try a hard reset!
Click to expand...
Click to collapse
Usually a hard reset solves everything (hopefully)

Sergio PC said:
Usually a hard reset solves everything (hopefully)
Click to expand...
Click to collapse
Tried hard reset, gets to grey screen with blue text but then reset loop again.
Nope

leave it charging for at least 10 minutes before turning it on.

bakman said:
leave it charging for at least 10 minutes before turning it on.
Click to expand...
Click to collapse
I cant switch off the device as soon as power is applied via USB it switches on. Tried holding the power button down but nothing.

don't even touch the power button!
the device should not start if you touch nothing and just plug the powercable!?
i don not think that you press the powerbutton accidentally while plugging the cable, i hope i'm right?

Without touching the power button, I plug in the charger and the phone vibrates and starts.
From dead:
1. Plug in charger
2. I get 2 swirls of white on the round button thing
3. Phone vibrates
4. Smart mobility logo shows
5. Phone reboots
GOTO 1:

i miss the touch diamond screening with rom version etc.
normally it shows up before the htc smart mobility screen.
i don't think the battery is the badguy. seems more a fault in ipl or spl?

You're right.
I was wrong when I said smart mobility.
It comes up with TOUCHDiamond across the centre of the screen and right where the little red numbers USUALLY appear in the bottom right, it reboots before that.

To perform a hard reset
1. Pull out the stylus.
2. With the device turned on, press and hold the VOLUME DOWN and ENTER buttons, then press the RESET button with the stylus tip.
3. Release the RESET button, but continue pressing the VOLUME DOWN and ENTER buttons until you see message on the screen
4. Release the VOLUME DOWN and ENTER buttons, then press the VOLUME UP button to perform the hard reset, or press any other button to cancel the reset
save this info on your computer

Sorted!
I left the battery out overnight, and when I came to work this morning, I plugged it into the charger and it didn't automatically start up so it got a good 3/4 hour charge which then enabled me to fire it up for a full charge.

congrats! i hope for you that this problem doesn't come back!

Sounds to me like it also could have been the power button was jammed pushed in. Maybe leaving it for a while without pushing the button did the trick, allowing it to release itself.
In case that was the problem, keep an eye on the power button in case it seems to be a bit dodgy. If it is going to do it again, then you want to swap it immediately for a replacement brand new unit. After a while, if you try to swap it out, they will give you a refurbished unit, not a brand new one!
Of course it could have just been a software bug, that was cleared by letting it fully power down (as others have said).
Just make your decision quick before you end up with a refurbished model for replacement.

Just to let you all know.
Over the weekend I fully charged my Diamond, and without even making a phone call or using WiFi, Bluetooth or anything the battery lasted 1.5 hours.
It's gone back to clove now for a replacement.
I've seen a few people having this issue so I advise getting it back for replacement asap.
My diamond got very hot during normal use (without charger). Is that normal? Not the battery but the actual device.

[Q] Nook won't boot - "Battery too low to power ON"

I recently installed CM7 nightly 12 and it's stuck at this screen. I'm using the stock charger. I've tried plugging it into my computer too.. no luck. Is there anything else to try? Am I screwed?

this sounds like something that was happening to me yesterday. i finally got it to charge by making sure it was completely off. i finally realized that even though the screen was dark it wasn't off, so it never charged (i think it was just recycling the charge enough to keep it on). if you look at it in a dark enough light you can see the screen is still on (backlit).
so plug it in, i would suggest using the wall charger. this usually makes it turn on (at least mine did), once it does, hold the power button until its off, no backlight is on. hope this makes sense and helps out a little

There's many others having this problem (me, on my friends nook, one of them). Hold down the Power button for a long period of time (I heard it's 10 seconds, but someone said they had to hold it for 30) and it will do a hard reset. At that point, try to turn it on again normally. If it doesn't turn on normally, plug it in (using the uSB cable that came with it (that is very important) and into the wall with the provided adapter), wait 30 minutes, and try again. It seems that very few (I don't know if i've actually read of any) who had this problem actually had to return the nook. When it happened to me with my bro-in-laws, he just hed the power button cause he was mad and it turned on, it hasn't happened to him since

Finally started working. I tried holding the power down for awhile with no luck.. Left it charging overnight and tried holding power again and it worked!

[Q] Dead power button+stock android 2.3.4 not turning on

So, I've got hold on a nexus one.
The guy who sold me told, that it has stock android 2.3.4 on it, no root, and that the power button is dead, but beside of that it's fully operational.
So I've googled the problem, and the solution was to plug in to the charger the phone, then pull out the battery, than put it back, and after a few tries the phone will boot up.
Unfortunately it hasn't.
When I plug in the charger (in the wall or to my pc) the led on the top right side starts glowing in green, and when I pull out the battery, the led turns of, but then, every 3-5seconds the led flashes one in orange, then one in green, then again nothing for a couple of seconds until I put back the battery, then it's all green again.
So I called the guy, who told me, that it's green, because it's fully charged, okay, and that the "plug in, pull the battery" method works only till android 2.2, and that it doesn't work with android 2.3.
So, is it true?
What can I do now, beside repairing it?
Can I turn it on somehow?
Is it sure, that it's only a power button issue, or can it be a more serious damage to the phone?

In order to have the phone turn on with the battery trick you have to have it plugged in. install the battery wait till the light comes on then remove and reinstall battery. it should power up seconds later. I have a Nexus one with a broken power button and it works every single time.

Quite a clever trick for getting the nexus one up and running. How'd you figure that out? Is there a resource with a bunch of suck tricks? I definitely didn't see this on the Google help page.
Is this applicable across other devices, or only on the Nexus One/passion?

won't turn on/can't select any boot options

I have a new Motorola Atrix HD. I was using it and the screen went black. i hit the power button to unlock but nothing happened. i plugged it in but nothing happened. i took the back off to see if the battery was disconnected. I didn't know the battery was different than other phones and ripped the power cord connecting the battery to the phone when i took it out. lesson learned. Ordered a new battery and installed correctly. phone won't turn on. The green charge light blinks when i plug it into the wall and then stays on for about 20 seconds and then the phone tries to turn on but while the motorola icon is illuminated, it cuts back out and repeats the cycle. I left it plugged in for a couple hours and still the same thing. i tried holding in power and volume buttons for the boot screen. if i do that just as the phone attempts to turn on i can get the screen up and scroll the list of boot options with the power buttons but i can't select any of them and the phone cuts out after the same amount of time. Everytime. When i plug it into my laptop, the light blinks on and then stays on like with the wall, but the phone doesn't attempt to power up. Please, any help would be greatly appreciated. i have read a lot of forums where the battery was acting up because of the chargers people were using. The difference between my situation and those of the people i read about is that my boot screen cuts out and cannot be used. This all happened 2 days after my exchange period ended and because i took the back off myself, best buy won't have anything to do with me so i'm on my own and cannot afford another phone right now. Thanks in advance for your time and concern.

katlic said:
I have a new Motorola Atrix HD. I was using it and the screen went black. i hit the power button to unlock but nothing happened. i plugged it in but nothing happened. i took the back off to see if the battery was disconnected. I didn't know the battery was different than other phones and ripped the power cord connecting the battery to the phone when i took it out. lesson learned. Ordered a new battery and installed correctly. phone won't turn on. The green charge light blinks when i plug it into the wall and then stays on for about 20 seconds and then the phone tries to turn on but while the motorola icon is illuminated, it cuts back out and repeats the cycle. I left it plugged in for a couple hours and still the same thing. i tried holding in power and volume buttons for the boot screen. if i do that just as the phone attempts to turn on i can get the screen up and scroll the list of boot options with the power buttons but i can't select any of them and the phone cuts out after the same amount of time. Everytime. When i plug it into my laptop, the light blinks on and then stays on like with the wall, but the phone doesn't attempt to power up. Please, any help would be greatly appreciated. i have read a lot of forums where the battery was acting up because of the chargers people were using. The difference between my situation and those of the people i read about is that my boot screen cuts out and cannot be used. This all happened 2 days after my exchange period ended and because i took the back off myself, best buy won't have anything to do with me so i'm on my own and cannot afford another phone right now. Thanks in advance for your time and concern.
Click to expand...
Click to collapse
Is it possible that the that connection between the power cord and the phone itself is loose or damaged? I'm just guessing here as I have never opened up the back of my phone.

I would check your battery terminals then leave it to charge if it does. You could also try a factory cable. Another thing would be to try fastboot while connected to your laptop and see if it stays on, and if it does, try reflashing all partitions.
Sent from my MB886 using xda premium

XT890 doesn't start at all.

Hello. This morning I've turned off the alarm, turned on WIFI and went back to sleep. I can't tell for sure, but I think the battery was low. During the next 2 hours I checked the time several times. I don't remember accepting any OTA. Eventually I got up, tried to check the time and the phone was off. I tried to turn it on, no effect. No matter how many times and for how long I pressed and held the power button, the green LED only flashed for a split second and that's all. I plugged in the charger, and the LED stayed lit -but- there was this barely noticeable flickering. Charged it for about 30, 60, 120 minutes, didn't start plugged or unplugged. I went to work, 8 hours later (phone was unplugged) I tried to turn it on again, this time the LED doesn't even flash, but when charging there is no flickering. No combination of buttons works. Windows doesn't find the device, neither does RSD.
I've never done anything 'custom' to the phone. The last change I made was setting the alarm to turn off by shaking (yesterday, never used this option before).
Is it dead?

Try taking SD card out and holding Vol down and then Power for 20 secs, then let go of Power,

Already done that, nothing. No matter how long I charge it now, after unplugging and pressing power button the LED doesn't even flash. Could it be a battery problem (before its death, it would last for a day)? Is there any way of recovering my data without buying a new one?

Try opening and disconnect battery for a bit.

I'll do that as a last resort, on weekend maybe since I don't have the tools with me. Any other clues?

Nobody knows how to help me?
I'm going to make a factory cable. Will this alone allow me to recover the data? Or if I'll be able to flash the phone, can I recover the data afterwards?
Also, I'm not sure if I understand correctly: does the factory cable recharge the battery or not? Is there a way to recharge it when removed from the phone?

Try to use medfield unbrick script. If You have only green led it seems to be bootloader error so this script should bring Your phone to life or Your phone has broken emmc and You can start looking for a new logic board. Good luck.

I've installed the drivers, but Windows and XFSTK don't recognize my device at all. Factory cable also didn't help. I liked my phone very much. :angel:

Did You enter medfield mode using combination with camera button??

By a combination you mean holding the camera button and connecting the phone to a pc? I tried that.

Disassembe Your phone, pull out battery, push power button for a 10 sec, plug in battery, push camera button and connect USB. If it wont help You I don't see any hope for Your phone.

Well, new option to try is a new hope. I'll try that on the weekend. Could you please be more specific:
1. Pull out the battery.
2. Press the power button and wait 10 seconds.
3. Insert the battery: should I be still holding the power button at this moment?
4. Press the camera button.
5. Plug in the usb cable (factory? regular?) - should I be still holding the power and camera buttons?

Battery trick is only to discharge capacitors. Sometimes even phone is dead it can turn on in some strange mode and then You can't boot it to flash. Thats why You need to pull out battery, push power for a few sec to completely discharge motherboard and just release this button. After that You can just plug in battery and continue normal unbrick process - so hold camera button only and connect regular usb cable.
You can also try reset option instead of pulling battery out. To do that do not disassemble Your phone but just plug in regular USB, when phone starts (green led) hold power and vol- until green led goes off and then quickly start holding only camera button.
I have no more ideas.

Ok, I've tried everything. Nothing brought my phone back to life.
Thanks for all your help.