[Q] Bootloop with nAa10 on X8/E15i [SOLVED!] - XPERIA X8 Q&A, Help & Troubleshooting

Hi!
I had a problem with my smart (if you call me, it reboot, something reboot automatically). I was using GingerDX v21 and v22. I downgraded to 2.1 via PC Companion but doesn't works.
So, I decided to use MiniCM7. I followed this tuto http://forum.xda-developers.com/showthread.php?t=1068553 and the bootloader unlock tuto too http://forum.xda-developers.com/showthread.php?t=1254225
Well, I did everything correctly, I guess. I see the nAa logo when I turn on my smart and I can enter in CWM-Recovery.
I have installed the MiniCM7-2.1.8-shakira, MiniCM7-2.1.7-shakira, MiniCM7-2.1.6-X8, GingerXperiaRay_V004 and PrimeHD20 but I can't pass of boot (bootlooping).
I don't know if I did something wrong. I had instaled too E15_nAa-09_2.6.29.6-nAa-09 and E15_nAa-06b_2.6.29.6-nAa-06b (first I tried v10). I everytime wipe all data.
If I install the original kernel and rom it works normally. I don't know what I can do. I do the same process three times, wiping all, installing, etc. and nothing!
What I'm doing wrong? There are some possibilities of my smart don't support it?

read this first http://forum.xda-developers.com/showthread.php?t=1011071 to go back to 2.1...
then root, install xrecovery,unlock bootloader,flash nAa kernel you need ,and then
install MiniCM7...

try this method
1.root
2.unlock bootloader
3.flash nAa v10
4.then your phone will have CWM and flash the rom minicm7.218
5.flash google gapps gb
6.reboot and see it bootloop or not??
Sent from my E15i using xda premium

Thanks for all replies.
Well, I did the @kostas_grevena3 method, but I'll do again. Maybe I forget to apply baseband 015! :O Hum...
What I'm doing now:
1. Flashing: Flashtool + X8 Shakira E15i_2.1.1.A.0.6_generic.ftf (success!)
2. Flashing: Flashtool + X8i_2.1.1.A.0.6_Baseband_015.ftf (success!)
3. Drivers yet installed from last tries. (success!)
4. Flashing: Flashtool + E15_nAa-10_2.6.29.6-nAa-10.ftf (success!)
5. Turn on smart, CWM and wipe all (success!)
6. Flashing: CWM + MiniCM7-2.1.8-shakira.zip (success!)
7. Flashing: CWM + gapps-gb-20110828-signed.zip (success!)
8. Rebooting for first time and...
MOTHER
OF
ANDROID!
Thanks you guys!
Feeling like a hacker now haha jk jk
Thanks!

try this.
1. boot in recovery
2. Factury Reset
3. mount/storage format system and sdext if you had an ext partiton
4. flash cm7 rom
5. boot now first complete to rom
6. Reboot to Recovery
7. Now you flash gapps
will it work now?
i remeber an error with odexed roms when i flash another zip before i boot in rom.
edit: oh sorry i see it sloved haha, have fun with your new x8

david.proweb said:
Thanks for all replies.
Well, I did the @kostas_grevena3 method, but I'll do again. Maybe I forget to apply baseband 015! :O Hum...
What I'm doing now:
1. Flashing: Flashtool + X8 Shakira E15i_2.1.1.A.0.6_generic.ftf (success!)
2. Flashing: Flashtool + X8i_2.1.1.A.0.6_Baseband_015.ftf (success!)
3. Drivers yet installed from last tries. (success!)
4. Flashing: Flashtool + E15_nAa-10_2.6.29.6-nAa-10.ftf (success!)
5. Turn on smart, CWM and wipe all (success!)
6. Flashing: CWM + MiniCM7-2.1.8-shakira.zip (success!)
7. Flashing: CWM + gapps-gb-20110828-signed.zip (success!)
8. Rebooting for first time and...
MOTHER
OF
ANDROID!
Thanks you guys!
Feeling like a hacker now haha jk jk
Thanks!
Click to expand...
Click to collapse
is this working?

First of all i would like to thanks all the Developers for their Incredible work on this site. I am using this site for a long time it helped me in solving many issues. I flashed many Custom ROMS on My X8 & X10 never had big issues so there was no need to post just becuase there was already so much of information here. But from last 4 days i am messing with my X8 when i tried flashing Jelly Bean Rom. Previously i was using 2.3.7 in my x8.I cant say i am very good but i am not new to these Roms. I actually searched alot but failed so i am here for help. In order to use Jelly Bean my x8 is having Bootloop issue. I follow all the instructions from http://forum.xda-developers.com/showthread.php?t=1789713 regarding Kernel http://forum.xda-developers.com/showthread.php?t=2136211. I follow each guidelines but still Bootloop . Not only that i cant use any other custom rom now everytime bootloop. SESU repair my phone but i cant use 2.1 now after using custom roms in x8 for longtime, It feels pathetic Now i dnt want Jelly Bean in x8 anymore i ll be more than happy if i get 2.3.7 back :angel:
I tried different Roms , Kernels but everytime same result "Bootloop"
Rooting fine, Flashing Kernel fine,, Rom instalation fine. Had doubt regarding Unlocking Bootloader ( Whether its properly unlocked or not). so Flashtool says Its "unlocked" but it also said it cant be "unlocked officially". So i tried another way to with s1 tools from this link http://forum.xda-developers.com/showpost.php?p=23680742&postcount=1 and r is smaller too RUNNING S1_EROM VER "r8A029". Now i am really confuse. tired and fed up 4 days GingerXperia, JellyBread.Jelly Bean everything failed
But i want to add 1 thing which is related to BLU because i cant dial *#*#7378423#*#* service menu from my x8 is that the clue or issue. Plz members help me out. Thanks in Advance.

Please Help

Damn ..
I have tried many times with naa kernel to flash rooms, but stuck in bootlop.
After I found this tread, flashed baseband 15 (I have selected only baseband to flash), flashed again nAa kernel and then custom ROM and phone is working.
Thanks

Related

[Q] GingerDX

Hey Guys
Am kind of lost At the Gdx instruction thingies
Okay i know how 2 install it
..
So
i have the 2.1 ..
With all the required Stuff
the baseband number...etc
So is it now like always?
P.S: My bootloader is unlocked ..
So again is it like always
install ZIP From either Xrec.. Or CWM??
And about the recommendation 2 install The Linux
is it Safe???????
Completely Safe i mean???
And what are the benefits of Linux + GDX ?
..
your answers are gonna be the reason 2 either install the Rom Or not :/
So please HELP?
I did like this :
1.FULL wipe
2.flash gingerdx v017
3.flash linuxdx
And everything is good Is it safe? If you did everything all right its safe now with latest gdx with latest linuxdx i have=NO LAG AT ALL, EVEN WITH MANY APPS INSTALLED AND LOW RAM! ! i really easily recommend it to you
Sent from my X8 using XDA Premium App
If you read carefully GingerDX v014+ requires CWM for install it, for v013- versions you can install with xRecovery.
And GingerDX is safe, little bugs in some versions but with solution in almost all.
In my opinion the battery drain is the most important issue, with the Governor in ONDEMAND my battery drains just in the night 20%, that's a lot. Now, with Smartass, the battery drains just 3% over night.
I don't know about the performance with LinuxDX Kernel. I can't help you with that.
I'm sure that in the respective post you can get more information.
proadi96 said:
I did like this :
1.FULL wipe
2.flash gingerdx v017
3.flash linuxdx
Click to expand...
Click to collapse
Totally wrong order. You should:
1. copy rom to SD
2. flash kernel from PC
3. install rom from X8 recovery
4. full wipe
0 - make backup
rav3n_pl said:
Totally wrong order. You should:
1. copy rom to SD
2. flash kernel from PC
3. install rom from X8 recovery
4. full wipe
0 - make backup
Click to expand...
Click to collapse
Hehe, sory but i did that and it worked so i just post what i did maybe some1 will use it but hey i have a question , how to enter recovery? Coz when i boot my phone there is no Sony Ericsson logo , just after start up after black screen there gigngerdx logo appers so how to enter recovery?
Sent from my X8 using XDA Premium App
Guys for the love of God don't Get me confused ..
Just flash the kernel,ater that do afull wipe, and then flash the ROM in CWM-Recovery.
And if it´s not stable, flash stock ROm with stock kernel again and flash ONLY GingerDX without the Kernel.
Dude
while flashing the Linux
it stopped ..
And told me 2 tick the God damn USB debugging !!
DAMN I FORGOT 2 TICK IT BEFORE !!
And the phone now won't Go ON..
At ALL !!
it just shakes ..
Then nothin
Am trying 2 Fix it with Sony ericsson update service
But the installation is STUCK!
completely it won't Work..
..
Damn????
you should flash by flashtools .
Or the battery is low.. it happened to me once when flashing my gf's x8. It took a while for me to realise it. Lol. Just a suggestion, based from my experienced.
proadi96 said:
but hey i have a question , how to enter recovery? Coz when i boot my phone there is no Sony Ericsson logo , just after start up after black screen there gigngerdx logo appers so how to enter recovery?
Click to expand...
Click to collapse
Sira. said:
Dude
while flashing the Linux
it stopped ..
And told me 2 tick the God damn USB debugging !!
DAMN I FORGOT 2 TICK IT BEFORE !!
And the phone now won't Go ON..
Click to expand...
Click to collapse
KERNEL - this you flashing using FlashToll from PC
ROM - zip file that you installing from CWM or xRecovery
Proper order (I assume that bootloader is unlocked already):
1. Make backup of apps using TitaniumBackup then xRecovery or CWM
2. copy new ROM to SD
3. turn on USB debugging
4. disconnect USB cable
5. shut down phone
6. run FlashTool and press "flash"
7. press and hold "back" button in phone and plug in USB
8. wait for flash is done ("flash complete ... disconnect ...")
9. disconnect USB
10. turn on phone and start tapping screen to enter CWM
11. using CWM menu install custom zip
12. do full wipe
13. reboot
14. wait.... it can take up to 5 mins
15. install Titanium and restore apps
If it will not run you just flash back stock kernel, then seus for stock rom, root it, install xrecovery or cwm and restore backup.

[Q] nAa kernel v10 flash problem

hello guys im new to the forum my problem is that i followed the method to flash a kernel(1st time) and i get the nAa's screen,i also have acess to cwm,then the logo dissapears and the phone stays blanc.(the only thing i can do is pull the battery)
Question: do i have to load the custom rom,then flash the kernel,then the loaded rom?
Install rom via cwm before you must flash kernel then you must wipe cache and enjoy
Press thanks button if i help!
Sent from my E15i using XDA App
flash kernel go to cwm do full wipe wipe dalwik cache wipe cache partition instal rom and reeboot
and what i say roflmao
Sent from my E15i using XDA App
the problem is that after i flash the kernel it doesnt boot to stock rom,the screen remains blank,what should i do??
gagagio said:
the problem is that after i flash the kernel it doesnt boot to stock rom,the screen remains blank,what should i do??
Click to expand...
Click to collapse
here's a few choices
1: Read the forums
2: Sell your phone and buy a 3310
3: actually only 2 choices
and before you ask USE THE SEARCH BUTTON
Lloir said:
here's a few choices
1: Read the forums
2: Sell your phone and buy a 3310
3: actually only 2 choices
and before you ask USE THE SEARCH BUTTON
Click to expand...
Click to collapse
well i read the forums but i didnt discover the same problem as me ...so again is the stock x8 rom not supposed to work after i flash the kenrel or am i doing something wrong?(ican get to cwm).MOreover,do i have to load the custom rom file first,then flash the kernel,then flash the loaded rom?
dude, flash nAa v10. after you flash it, the kernel logo will appear followed by the battery sign.
press power button, the phone will boot and the kernel logo will appear.
you will be sent do CWM Menu.
if you have a compatible ROM for nAa kernel, do a full wipe and reboot and see if the ROM boots successfully.
if you dont have a compatible ROM, do a full wipe, install CM 2.1.8 and then reboot.
U have to unlock bootloader first before flashing kernel,
this is the step (with stock kernel and rom installed and root) :
- unlock bootloader
- flash kernel
- enter cwm
- wipe data
- install custom rom
- wipe data again
- restart system
and ur good to go
gagagio said:
hello guys im new to the forum my problem is that i followed the method to flash a kernel(1st time) and i get the nAa's screen,i also have acess to cwm,then the logo dissapears and the phone stays blanc.(the only thing i can do is pull the battery)
Question: do i have to load the custom rom,then flash the kernel,then the loaded rom?
Click to expand...
Click to collapse
You cant load stock rom with a custom kernel. Just flash GingerDx Rom and you should be fine. Flash the kernel first using the flash tool, then flash the rom using CWM and then turn on the phone
ty very much guys( especially bahmonkeys)!I should have known that
gagagio said:
ty very much guys( especially bahmonkeys)!I should have known that
Click to expand...
Click to collapse
No problem im here to help!!!
Here is a newbie guide to unlock the bootloader
http://forum.xda-developers.com/showthread.php?t=1436924&page=2
After you unlocked BL you can flash the kernel with flashtool (with the latest one)
-Don't forget to copy you're rom to SDcard!
When the nAa logo appears hit the back button and you're in cmw menu.
full wipe->instal custom rom-> reboot your phone !
first flash your kernel and then install custom rom...

[Q] Stucks after flashing or installing ROM.

I flashed the latest official firmware...
Than after all my attempts i can't install any ROM, except official 2.1.
Please, write me instructions how to install CM7 - i need help...
I have rooted 2.1 with xRecovery - what's next?
Go to xrecrovery choose instal custom zip from sd card hoose zip from sd card find your mini cm 7 install rom and factory reset/full wipe.
It depends on ROM. Some of CM7 works only on custom kernels, so You should first check if You will be able to unlock bootloader. Look behind Your battery - on the stick there should be something like xxWyy which will tell You the year and the week of Your board. If it's older than 11W26 (26th week of 2011) - U may unlock bootloader and install custom kernel (on Your own risk ;P). If not - You shouldn't do this and search for ROMs working on SE stock kernel
Bolussimo said:
It depends on ROM. Some of CM7 works only on custom kernels, so You should first check if You will be able to unlock bootloader. Look behind Your battery - on the stick there should be something like xxWyy which will tell You the year and the week of Your board. If it's older than 11W26 (26th week of 2011) - U may unlock bootloader and install custom kernel (on Your own risk ;P). If not - You shouldn't do this and search for ROMs working on SE stock kernel
Click to expand...
Click to collapse
Also, some ROM required CWM instead of Xrecovery, so read carefully before attempting anything.
Hmmmm
I unlocked bootloader long time ago(10WW48 on the sticker).
to przemek4113: Just installing from xrecovery gives me a unbooting phone.
I tried Froyo, but it doesn't boot too.
Then i'm flashing(Xrecovery doesn't give me a booting phone even if i recover all system) official 2.1.
This phone was bought with GinderDX on it. But latest versions need new kernels(flashing kernel bricks phone).
May be try Previous versions of GingerDX?
Really, i tried about seven customs...
P.S. I'm installing xrecovery ROM's from Xrecovery and CWM ROM's from CWM...
BEaStia said:
This phone was bought with GinderDX on it. But latest versions need new kernels(flashing kernel bricks phone).
Click to expand...
Click to collapse
Mind to elaborate where you read that "latest versions need new kernels"?
GingerDX runs on STOCK KERNEL, LinuxDX as well as Alfs. I fail to find the part in doixanh's post where it says something about forcing a certain kernel to be used.
Make sure you have an older x8 than 11w29, its under the battery. When the number is 11w29 or newer, you'll not get CM. Unlock your bootloader.
Download and flash FXP kernel. Install official CM with the kernel built-in CWM. I recommend to flash nAa kernel after install the CM, it's much better.
Sent from my E15i using xda premium
If you want CM7 you should go to this thread...http://forum.xda-developers.com/showthread.php?t=1362585
That's my fault - i was speaking about another ROM. Not GingerDX - but it doesn't boot too.
I followed advise about miniCM7.
Flashed kernel ->then wiped all(i disliked the message about ext4 - there's no this partition - probably that's the problem???) ->installed ROM. Nothing.
"nAa kernel" logo appears and then it reboots.
UPD:
I've installed GingerXperia(v19) via CWM.
Then -
I've flashed all kernel,fota and smth else(not all files from 2.1.1).
Then it booted...strange)
But i'll try to work with other kernels...
hi
i had rooted my w8 with super1click installed xrecovery and with it gingerxperia v22.today i installed v24b and rebooted.then installed chargemon zip.but after this my phone stuck at se logo ...its not even shutting down so no xrecovery or pc companion working...somebody pls help...
sreeramllb said:
hi
i had rooted my w8 with super1click installed xrecovery and with it gingerxperia v22.today i installed v24b and rebooted.then installed chargemon zip.but after this my phone stuck at se logo ...its not even shutting down so no xrecovery or pc companion working...somebody pls help...
Click to expand...
Click to collapse
Probably:
1)make a backup of all data
2)flash stock kernel
2.5)wipe
3)install custom
3.5)wipe
4)recover data
?
1.As my phone is not booting can't take back up but i have previous back up with me
2,how can i flash stock kernel ?is it with flash tool?
sreeramllb said:
1.As my phone is not booting can't take back up but i have previous back up with me
2,how can i flash stock kernel ?is it with flash tool?
Click to expand...
Click to collapse
Flash Tool - I've seen links on it thousand times on 4pda.ru, but not here - i suppose it to be in the branch about X10.
http://www.mediafire.com/?z7fmpiragbbdxdu - here is flasher.
http://depositfiles.com/files/c2gllgt6t - or here, with official firmware
It would be great if somebody could provide the step by step procedure of flashing my w8 to get past the se logo....
1)Download all archives above
2)Run flasher
3)Press "Flash" and choose necessary firmware
4)follow advices of software
5)reboot -> You have official 2.1
then
1)check your bootloader(http://4pda.ru/forum/dl/post/1227710/S1tool.7z) with this tool
2)unlock it if it is able for you
3)take root(superoneclick with debugging)
4)make xrecovery
5)install any xrecovery zip
or
alt 5)make CWM
alt 6)install any CWM zip
or
install kernel
then install zip
Firstly try it from xrecovery. If you have some problems - write PM to me)
I have done it and successfully flashed as per flashtool...but now even i cant boot stuck at "sony ericsson" now the animated logo works and reboots automatically...pls help
Have you done "user-wipe" in Flash Tool???
Here is from friendly branchcontains a collection of GingerDX 013-022 and some other goodies in the "Sony Ericsson" folder - i.e. Basebands, PCC, SEUS, Flashtool)
http://www.mediafire.com/?eca0sualnao4c4c
Thanks to B.Jay
Atlast with full user data wipe in flash tool I recoverd my phone...THANKS A LOT!!!
Again rooted,Xrecovery and installed GX V24b-I would like to know how to enable multi touch in it please?
How to make xperia x8 able multi touch.
i want to know what i have to do to make xperia x8 able multi touch(im using gingerxperia v23 on my x8)...can anybody help me plz..i appreciate your help...
:-D
chehady said:
i want to know what i have to do to make xperia x8 able multi touch(im using gingerxperia v23 on my x8)...can anybody help me plz..i appreciate your help...
:-D
Click to expand...
Click to collapse
Ok here is a nice way how to enable it hope it helps you
http://forum.xda-developers.com/showthread.php?t=1135965
Sent from my E15i using XDA App

What was wrong ? Mini CM9 on Xperia X8

Hi everybody,
I tried yesterday to flash my phone with the new mini CM9 + nAa 04 kernel... It did not work resulting in a soft brick.
I solved this problem by flashing back to the stock rom + kernel using flashtool. My device is now working as before.
After many unfruitful research on the forum, i'm forced to ask you what wrong did I do...
My phone was (and is) configured as follow :
Kernel : stock 2.6.2.9
Rom : Android 2.1
Base Band Version : M76XX-TSNCJOLYM-53404015
Built : 2.1.1.C.0.0
Rooted
Bootloader : unlocked
Today I installed xRecovery (which is not needed if I use the Kernel E15_nAa-ics-04_2.6.29.6-nAa-ics-04).
Is it problematic if I want to use the mini CM9 rom ?
How did I do :
I started by flashing the kernel using flashtool and with the latest version kernel E15_nAa-ics-04_2.6.29.6-nAa-ics-04.
The manipulation was successful and kernel was working well.
Then, after having backed up all my settings, apps, contacts, rom and wiped off the data factory settings, I started to flash the rom with CWM (the rom had been stored before on my SD card).
Once the installation finished, the phone reboot... and reboot .... and reboot, etc...
It was only able to display the nAa kernel screen (boot loop), but nothing more.
Finally, I flashed it back to stock version to use it again... OUff
I was a bit scared by the idea of having a hard brick but finally it was just a soft brick.
What do you think about my experience ? I know many of you think that people who do not have necessary skills to do it should not do it ^^ but I want to learn and to make my phone a bit more flexible and fast.
Thank you in advance !
Nico
P'titbateau said:
Hi everybody,
I tried yesterday to flash my phone with the new mini CM9 + nAa 04 kernel... It did not work resulting in a soft brick.
I solved this problem by flashing back to the stock rom + kernel using flashtool. My device is now working as before.
After many unfruitful research on the forum, i'm forced to ask you what wrong did I do...
My phone was (and is) configured as follow :
Kernel : stock 2.6.2.9
Rom : Android 2.1
Base Band Version : M76XX-TSNCJOLYM-53404015
Built : 2.1.1.C.0.0
Rooted
Bootloader : unlocked
Today I installed xRecovery (which is not needed if I use the Kernel E15_nAa-ics-04_2.6.29.6-nAa-ics-04).
Is it problematic if I want to use the mini CM9 rom ?
How did I do :
I started by flashing the kernel using flashtool and with the latest version kernel E15_nAa-ics-04_2.6.29.6-nAa-ics-04.
The manipulation was successful and kernel was working well.
Then, after having backed up all my settings, apps, contacts, rom and wiped off the data factory settings, I started to flash the rom with CWM (the rom had been stored before on my SD card).
Once the installation finished, the phone reboot... and reboot .... and reboot, etc...
It was only able to display the nAa kernel screen (boot loop), but nothing more.
Finally, I flashed it back to stock version to use it again... OUff
I was a bit scared by the idea of having a hard brick but finally it was just a soft brick.
What do you think about my experience ? I know many of you think that people who do not have necessary skills to do it should not do it ^^ but I want to learn and to make my phone a bit more flexible and fast.
Thank you in advance !
Nico
Click to expand...
Click to collapse
Your hardware and software seems alright to me.
Steps: Don't bother about xRecovery. From stock 2.1...
Root again
Flash nAa-ics kernel
Install MiniCM9 and Gapps from first post of MiniCM9 thread
FULL WIPE -- YOU MUST DO THIS
WIPE DALVIK-CACHE TOO
Reboot and have fun
Sent from my X8 using Tapatalk 2
Flash the latest baseband ans try again
Sent from my E15 using Tapatalk 2
Full Wipe will solve the problem.
Sent from my E15i using xda app-developers app
Hi,
Thanks for your replies.
So I don't understand what was wrong as I completely wiped the system prior to flash the Rom.
I proceeded exactly like that :
1.Wipe data factory
2.Wipe cache
3.Wipe dalvik-cache
4.Format system
5.Format cache
6.Format data
7.Rom installation
8.Flash Gapps
I think I have done all the necessary steps to make it working ...
I was maybe not enough patient after installation ?
I'm going to try again today (now I know how to recover from a soft brick ).
Thank you all again.
P'titbateau said:
Hi,
Thanks for your replies.
So I don't understand what was wrong as I completely wiped the system prior to flash the Rom.
I proceeded exactly like that :
1.Wipe data factory
2.Wipe cache
3.Wipe dalvik-cache
4.Format system
5.Format cache
6.Format data
7.Rom installation
8.Flash Gapps
I think I have done all the necessary steps to make it working ...
I was maybe not enough patient after installation ?
I'm going to try again today (now I know how to recover from a soft brick ).
Thank you all again.
Click to expand...
Click to collapse
Good job dude!
just try and try lolZ
maybe you miss something like flash or root..
libera powaemm
It works ! My phone is now booting and I see the CM9 blue droid :highfive:
Special thanks to developers who allow us to have better software !
And thank you for the support you brought me.
congratulation!
P'titbateau said:
It works ! My phone is now booting and I see the CM9 blue droid :highfive:
Special thanks to developers who allow us to have better software !
And thank you for the support you brought me.
Click to expand...
Click to collapse
well well!
enjoy it! :laugh::laugh:
having the same problem
P'titbateau said:
It works ! My phone is now booting and I see the CM9 blue droid :highfive:
Special thanks to developers who allow us to have better software !
And thank you for the support you brought me.
Click to expand...
Click to collapse
So, what step u miss? I also having the same problem. Can tell me your steps? dying for CM9 in my X8 too T-T
slyzerx said:
So, what step u miss? I also having the same problem. Can tell me your steps? dying for CM9 in my X8 too T-T
Click to expand...
Click to collapse
just do what spyder-x said dude!
:laugh::laugh:
Same problem... when i try to install it again I get an error and it says my device is 16i insted of 15i ...
Then I had to flash different rom 3 times to get it working...
Didn't wipe cashe and it worked : )
first instal minicm 3.0.4
after that install minicm 3.0.5(or any nightlie) without any wiping!.

xperia T orange jamesbond edition

Hello guys, im new here but i need your help.
Like i said i have xperia lt30p and I cant install http://forum.xda-developers.com/showthread.php?t=2040066, dont know why i did everytihing with instruction for locked bootloader and still the same. So my problem is : after installing everything im trying to turn on my xperia and its just vibrate and nothing going on... just one vibration. help me please...
igorskyxxx said:
Hello guys, im new here but i need your help.
Like i said i have xperia lt30p and I cant install http://forum.xda-developers.com/showthread.php?t=2040066, dont know why i did everytihing with instruction for locked bootloader and still the same. So my problem is : after installing everything im trying to turn on my xperia and its just vibrate and nothing going on... just one vibration. help me please...
Click to expand...
Click to collapse
sounds like a kernel issue.
Code:
Locked bootloader
1. Root with Bin4ry's method(*)
2. install CWM for locked bootloaders.(*)
3. Go to recovery, wipe cache & dalvik-cache
4. Flash ROM
5. Flash kernel .140 (if you haven't already)
6. Reboot.
7. When CWM asks "ROM may flash stock recovery on boot. Fix?", answer "No".
8. Enjoy
(*) skip these steps if you're already on a custom ROM with CWM recovery or unlocked bootlader.
Are you sure you did all these?
s
gregbradley said:
sounds like a kernel issue.
Code:
Locked bootloader
1. Root with Bin4ry's method(*)
2. install CWM for locked bootloaders.(*)
3. Go to recovery, wipe cache & dalvik-cache
4. Flash ROM
5. Flash kernel .140 (if you haven't already)
6. Reboot.
7. When CWM asks "ROM may flash stock recovery on boot. Fix?", answer "No".
8. Enjoy
(*) skip these steps if you're already on a custom ROM with CWM recovery or unlocked bootlader.
Are you sure you did all these?
Click to expand...
Click to collapse
yes and not once, i have tried 4 times...
ok, does your phone turn on at all?
If so tell me what it says in the last 4 entries in
settings/about phone.
If it doesn't do a repair using pccompanion then tell me the same thing again
after flashing I cant but always i can "reset" by update service by sony , now its
android ver. 4.1.2
bandwidth version 8960A-AAAAAANAZQ-10015031-47
kernel 3.4.0-g5b05b2-00811-g8c0b35e
[email protected]) ) #1 SMP preempt tue mar 19 12:47:46 2013
And the last line : 91.A.1.140
ok, how are you installing CMW? Which link are you following?
cwm
gregbradley said:
ok, how are you installing CMW? Which link are you following?
Click to expand...
Click to collapse
dropbox.com/s/c4ss88zgnx178ot/CWM4XperiaT_v7i_JB.zip
This one..., im just connecting xperia t with usb debugg ,and via PC click install.bat ,something wrong?
That should be fine.
Next try this.
Flash it again, but this time goto
mouts and storage and make sure you mount system first, then flash it...
EDIT:
Just a thought, after flashing the rom are you wiping system as well as dalvik and cache...if so then D'OH, don't wipe system, that deletes the rom you just installed
after flashing rom? i dont wipe anything , just before flashing
ok
gregbradley said:
That should be fine.
Next try this.
Flash it again, but this time goto
mouts and storage and make sure you mount system first, then flash it...
EDIT:
Just a thought, after flashing the rom are you wiping system as well as dalvik and cache...if so then D'OH, don't wipe system, that deletes the rom you just installed
Click to expand...
Click to collapse
I dont undestand, what do u mean goto mouts and storage and make "SURE you mount system first" ?
enter recovery
goto the section that says
mount and storage
then choose mount system
then flash the rom
will do in 30mins, will say progress here
it still nothing... just vibrating
Redownload the .zip file
Sent from my GT-P3110 using xda app-developers app
yeah,but i think its not .zip problem... I had the same problem with CM 10 ... Maybe I just cant install other roms on my xperia T from orange with blocked bot etc...
You cant install custom kernels but you should be able to install stock based roms.
Are you trying to install a kernel? If so then dont.
Repair in pccompanion, root, install cmw recovery and flash rom.
It should work, if not try a different rom that is stock based
Sent from my GT-P3110 using xda app-developers app
I'll be grateful if u can show me rom which can work on my XPERIA T , I'm not experienced enough to choose stock or not ,sorry for problems..
And if u can say, how i can get flashtool? I will try this one http://forum.xda-developers.com/showthread.php?t=2026885
I have got EMMA but its not avaible for me...
Of coyrse you cant use emma. If you read the instructions its for unlocked bootloaders.
In order to get flashtool just look in the dev section for it.
To decide if a rom is stock based, read the op of the roms thread, it will say what it is based on there.
You should be able to flash my rom if you follow the instructions properly
Sent from my GT-P3110 using xda app-developers app

Categories

Resources