Database Develop

[Q] Captivate With I9000 Firmware Stuck in Recovery Mode

There have been those that run into problems after installing the XXJP3I9000 update on the Samsung Captivate and attempt to reboot into recovery mode. The issue that they have is that since the Captivate has no physical home button to select an option like you can with the Galaxy S, you can't select an option, and therefore you can't reboot your device regularly. While I am in this same problem and have not figured out a solution, I have started this thread to post what knowledge I have about this issue so that others may help get this issue figured out. If anyone has information on how to fix this problem, please comment below. Let's fix this!
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
First of all, the key combinations that standardly would work with the original captivate firmware will not work anymore. Pressing all three buttons (Vol+, Vol - and Power) will only power cycle the phone, that is, until you let up on the buttons. Pressing Vol+ and Vol- and then plugging your phone into the computer will also do nothing. (By nothing I mean will take you back to the recovery menu)
Every key combination will only take you back to the recovery menu, so key combinations seem to be out.
If you boot into recovery mode, take out the battery and put it back in, all the while keeping the phone plugged in to the computer, the phone will enter the "POWER RESET OR UNKNOWN UPLOAD MODE", which will show your device in windows as being a Samsung USB Composite Device and a Samsung Mobile Modem (gadget serial, Windows 7) While this may be helpful, you cannot run ODIN or ADB in this mode, nor does this allow disk access. If you have Samsung Kies installed, it will detect a device, but will never complete loading it.
Other information with this method: On the phone screen, as well as showing "POWER RESET OR UNKNOWN UPLOAD DEVICE" the screen will also show the following in red:
RST_STAT =0X1
PMIC_IRQ1 =0X0
PMIC_IRQ2 =0x0
PMIC_IRQ3 =0x4
PMIC_STATUS1 =0x40
PMIC_STATUS2 =0x2c
If this helps anybody, it was a pleasure
Another method I found briefly was that after installing Kies, and rebooting the phone into recovery mode (again) my computer detected four new devices, two of them being Samsung Android devices and one being a disk drive. Potentially, without freezing or error, the drivers that are included with the Kies software will detect and allow for disk management while the phone is in recovery mode. Three of the four devices installed without error for me, but the fourth, the actual Android device, continued to say "installing device" until I unplugged the phone out of frustration. It has since not detected those four devices again, and I have yet to figure out how to do that again. The nice thing about that was that although the adb.exe reboot download command did not work, adb.exe did detect the phone. if this is true then rebooting normally or into download mode should be easy.
The last thing I noticed is that button furthest to the left on the main screen on the captivate will close the recovery menu when pressed, and leave the background behind, and then will reopen the recovery menu when pressed again. This is showing me that the four touch buttons are operable, but not configured. If it were possible to reconfigure the actions that pressing these buttons do, then it would be easy to be able to reboot the device normally.
I have compiled information to the best of my ability, and here is a question to ask, that I think will help solve the problem. Can the captivate with I9000 2.2 software run adb in recovery mode?
Comments, Questions, and Most of all, answers would be appreciated for me, as well as for other users with the same problem as I. Hopefully, this thread can be the solving point for this problem.
Many Thanks,
TouchofDestiny
The n00b who isn't a n00b at all

An Update: The reason that the combinations don't work for me or either people is because they (and I) fail to install the captivate kernel, and that is making the volume power button controls useless.

same here i put froyo from the galaxy s i9000 and i cant change the rom or get into recoverymode because buttons dont work man this sucks and 3G or Edge doesnt work.....

You're problem is a little different. If you can't get into recovery mode, than that means you aren't in recovery mode, which means you can use ADB to enter download mode and use Odin to flash your phone. I have given up looking for a solution, and have sent my phone back to AT&T for a replacement. Since I'm still in my thirty day trial period, it doesn't matter if I used different firmware or not. Hopefully others won't get into the situation I had. For me, this thread is complete.
brandon9721 said:
same here i put froyo from the galaxy s i9000 and i cant change the rom or get into recoverymode because buttons dont work man this sucks and 3G or Edge doesnt work.....
Click to expand...
Click to collapse

hi,
I solved the same problem doing this:
start odin.
take out battery. plug in USB. press both volume buttons. insert battery while pressing those buttons.
Done. download mode should appear.

yep, same boat
I am in the same position here. I downloaded the froyo leak and installed it with odin, no problem there. Upon startup into froyo, all was good, except my phone was stuck in horizontal mode until I tilted it vertical, *then* it would go horizontal. So basically I am 90 degrees off kilter. I decided to look around for another rom to try, and in the process managed to get stuck in recovery mode. Couldn't tell ya what firmware I have, just what is on the endless recovery screen that I cannot get out of!
I have no external microSD card, only the SIM card, and no way to get it recognized on my XP or win 7 system.
Really, really stuck here, guys. I do have the androidsdk installed, if there is a way to get it to reboot. As it is, adb cannot see the device, so I am looking at a truly bricked phone.
And yes, this is a US phone, which is why the power button and home button are not mapped (I assume).
I am DESPERATE for some help here!

and while I am at it...
I WAS able to get into download mode with the shovel guy originally by using the 2 volume keys+power, usb (odin up), battery in, release power.
No more. No key combo works.
Totally bricked the Samsung, which is supposed to be impossible!

pkrouse said:
I WAS able to get into download mode with the shovel guy originally by using the 2 volume keys+power, usb (odin up), battery in, release power.
No more. No key combo works.
Totally bricked the Samsung, which is supposed to be impossible!
Click to expand...
Click to collapse
when you are on the i9000 rom the only button that will get you in download mode is the vol down

That's HUGE!
You, sir, are a gentleman, scholar, and all-round smart guy! How did I miss that? I coulda SWORN I was getting into download mode with both volume keys. I've never been so happy to see a little Dalek dude with a shovel in my LIFE. 2 minutes in the one-click installer and now I'm back in business!
Thanks for helping a terrified owner out, and preventing a trip to the AT&T store.

I cannot go to download mode
I have the same problem here. Stuck in the recovery mode after upgrade the froyo and had the orientation problem. How do you go into download mode or power reset or unknown upload mode? Any button combination doesnt seem to work for me.
How do I do?
Please HELP. I am struggling here
Thanks

xaga150 said:
I have the same problem here. Stuck in the recovery mode after upgrade the froyo and had the orientation problem. How do you go into download mode or power reset or unknown upload mode? Any button combination doesnt seem to work for me.
How do I do?
Please HELP. I am struggling here
Thanks
Click to expand...
Click to collapse
the key to the i9000 rom/kernel button combo is VOL DOWN + using the USB trick. do not press vol up + down, just the down while you are plugging in the usb cable

i too am stuck in recovery mode. the only way i can get into download mode is by using both volume buttons. just holding the down button just sends me to revoery mode as well. how can i fix my phone in download mode?
nevermind, reinstalled 2.2 and it works now.

Eureka I got it...I think
I installed froyo 2.2 i9000 on my captivate and got stuck in recovery mode...power button doesnt select and when I hold down the up and down vol buttons I couldnt get the downloading icon anymore either. Then I remembered something from another post....
Home + Vol Down + Power = Downloading Icon
It worked for me....let me know if this helped....I'm officially unbricked.

Hey. I'm in the same boat. My Captivate has I9000 firmware running it and it won't run properly. I can't access the settings to enable USB debugging in order to boot in either Recovery or Download using adb and no button combination works for me. I can't use button combos to boot into either Recovery or Download mode.
Does anybody have any idea what is going on and how to fix this?

JPBetley said:
Hey. I'm in the same boat. My Captivate has I9000 firmware running it and it won't run properly. I can't access the settings to enable USB debugging in order to boot in either Recovery or Download using adb and no button combination works for me. I can't use button combos to boot into either Recovery or Download mode.
Does anybody have any idea what is going on and how to fix this?
Click to expand...
Click to collapse
JPBentley-- Since the I9000 firmware is set to use physical buttons, and the Captivate doesn't contain any, once you get into recovery mode, you cannot get out. The standard Captivate key combinations to get into download mode do not work, as do the combinations to get into download mode via the I9000 firmware. Basically, you get to a dead end. Unless there is some way to flash the phone's ROM outside of download mode, which I doubt, your best bet is to return the phone for a replacement. After haggling around with AT&T for a while, they admitted that installing the I9000 ROM doesn't invalidate your warranty, so they should take it back. They did with mine, and now I'm running the official Froyo leak. Good luck with your new phone!

SOLUTION
For all those that are having this problem, Ive struggled with it & tried EVERY possible button combination & nothing worked.
The ONLY solutions I have found is to use a usb JIG. Take out the battery, sim card & sd card, plug in the Usb JIG & put the batter back in. Give it a couple of seconds & I'tll enter recovery mode without pushing any buttons. You dont even need to push the power button, it's that simple.
Here is an image of how to make one if you are electronically inclined, personally I am not so I found a local electronic parts store & they put on together for me.
1.bp.blogspot.com/_3KjgtwnRiWM/TNTyjkZGquI/AAAAAAAABL4/7NSmqrYmkmU/s640/i900.jpg
If you want, you can also buy one online, I cant post a link becuase Im a new member but just search for "samsung usb jig" on ebay.com & youll find plenty.
shop.ebay.com/?_from=R40&_trksid=p5197.m570.l1313&_nkw=samsung+usb+jig&_sacat=See-All-Categories

yes, i think you need to build a jig or buy one online if you want to play with custom rom. you may not need it now, but you may need it just in case.
http://cgi.ebay.com/ws/eBayISAPI.dl...47234&ssPageName=STRK:MESELX:IT#ht_511wt_1139

agustinpac said:
hi,
I solved the same problem doing this:
start odin.
take out battery. plug in USB. press both volume buttons. insert battery while pressing those buttons.
Done. download mode should appear.
Click to expand...
Click to collapse
OMG you saved my life
thx so much for your post

I have the same problem, i can get into recovery mode. I can also get to download mode but Odin doesnt see my phone and neither does adb. By pulling the battery with no buttons pushed it goes straight into recovery mode. Looks like I have a brick now. If anybody has any suggestions please let me know.

drowe24 said:
I have the same problem, i can get into recovery mode. I can also get to download mode but Odin doesnt see my phone and neither does adb. By pulling the battery with no buttons pushed it goes straight into recovery mode. Looks like I have a brick now. If anybody has any suggestions please let me know.
Click to expand...
Click to collapse
That's not even close to a brick. Are you using a usb port closest to the motherboard on your pc? Is your cable good? Make or buy a jig, that will put your phone into download mode.
Sent from my blazing fast Captivate running Continuum GB ROM using Tapatalk Pro

PAYING for help!

Since i live in Brazil and here the galay s i9000 version is much different then our captivates and there is any place where i could try to fix my captivate i´ve decided to donate US$ 50,00 for who helps me fix my phone.
Here is exactly what happened:
I was already on cognition 2.3b6 but decided to flash back to stock and flash it again to 2.3b6 since i´ve never flashed back to stock and sincer i installed the firts custom room.
I installed the stock version usin odin 3 ( the files from cognition download threat ) and i didnt disabled lag-fix netheir deleted any folder or anything at all.
The installation to stock was succesful, then i used one click root installed the rom manager and selected the 2.3b6.zip
After rebooting it went to recovery screen as usual.. i selected the reinstall packages options and it reboot again, now it stuck some time on the at&t logo ( never had the voodoo voice ) ...and the rebooted again..
and here is the part where i know i was stupid
this time it entered on clockwork recovery mode then i tryed to backup and mount and it came back again to clockwork recovery mode... then i decided to wipe data and cache... then to format my sd card ( stupiedest point ! )..after i tryed to install packages again and after reboot it stayed like it is now
without the usb cable... if i turn it on it goes to at&t logo screen then it flashes on at&t logo... and then boot on recovery mode.
if i put the battery...plug the usb cable and try to turn it on.. the phone doesnt go to at&t logo.. it just stays on the charging mode.
i already tryed all download modes and none of them worked...
here is the list of things i´ve already ordered from sparkfun if i need to build that JIG thing...
1 - $10.95 - COM-09258 - Resistor Kit - 1/4W
1 - $3.95 - BOB-10031 - USB MicroB Plug Breakout Board
other info:
when i get on the at&t logo or recovery mode odin recognizes the phone as a com 4... so i cant flash it with odin...
and when i try to reboot on download mode using adb i receive an error msg " [1] segmentation fault " when i try to get the SU
any help ?

Can you still get to clockwork recovery?
If you can still get to cwm, download this http://www.ponack.net/designgears/JH7_OTA.zip and copy it to your external sd card, and try to flash it.
For download mode did you try:
1. Start odin
2. Remove battery from phone
3. Plug usb cable into phone
4. Hold down both volume buttons
5. Put battery back in while holding both volume buttons
Sent from my Captivate

not anymore...

curti.nogg said:
Can you still get to clockwork recovery?
If you can still get to cwm, download this http://www.ponack.net/designgears/JH7_OTA.zip and copy it to your external sd card, and try to flash it.
For download mode did you try:
1. Start odin
2. Remove battery from phone
3. Plug usb cable into phone
4. Hold down both volume buttons
5. Put battery back in while holding both volume buttons
Sent from my Captivate
Click to expand...
Click to collapse
is there any specific way to get on clockwork recovery ?
when i try to get on download mode like you said it just keeps charging the battery...
its strange.. when the usb is plugged the phone doesnt go enter on recovery mode netheir at at&t logo

tegots said:
is there any specific way to get on clockwork recovery ?
when i try to get on download mode like you said it just keeps charging the battery...
its strange.. when the usb is plugged the phone doesnt go enter on recovery mode netheir at at&t logo
Click to expand...
Click to collapse
If it's still on the internal sd card and you can get to recovery, choose the option "reinstall packages" it should do something and then it may kick you back to recovery 2e and then try one more time.
Sent from my Captivate

curti.nogg said:
If it's still on the internal sd card and you can get to recovery, choose the option "reinstall packages" it should do something and then it may kick you back to recovery 2e and then try one more time.
Sent from my Captivate
Click to expand...
Click to collapse
i can get on recovery 2e but when i try to reinstal packages it says that /sdcard/update.zip doesnt exists

Search for instructions on building a jig. It is a device that forces download mode, you need a spare cable our connector to cut up and some resistors. http://forum.xda-developers.com/showthread.php?t=841512
Sent from my SAMSUNG-SGH-I897

so my only hope is tat jig thing ?!
if yes i will stay a while without my phone =/

Wait so what happens if you have odin one click open, then unplug usb, pull battery, then put the battery back in and then plug usb in while holding both volume buttons. That's usually the surefire way to get download mode.
Sent from my SAMSUNG-SGH-I897 using XDA App

No.. the Battery trick should work. If your getting the battery charging while the device is turned off and the USB is plugged in that battery trick should work.
I've horked my phone harder then you have an still managed to get back into download mode.
The trick is remove the sim/sdcard and battery.
Plug in the USB
Then jam the battery back in.
Also.. if it's looping at the ATT logo you might have it up enough to do ADB commands.
See if your computer is recognizing the device. - ADB Devices - If it returns a value then you can just do:
Adb reboot download.
And Odin 1-click as normal to restore it.

KCutrer1 said:
Wait so what happens if you have odin one click open, then unplug usb, pull battery, then put the battery back in and then plug usb in while holding both volume buttons. That's usually the surefire way to get download mode.
Sent from my SAMSUNG-SGH-I897 using XDA App
Click to expand...
Click to collapse
it keeps frozen on the charging circle ( the grey circle doesnt keep moving )

I'd try pulling the battery again - it takes a few times to try and get it.
But.. I would try doing the ADB commands and see if you can get it into download that way.

avgjoegeek said:
I'd try pulling the battery again - it takes a few times to try and get it.
But.. I would try doing the ADB commands and see if you can get it into download that way.
Click to expand...
Click to collapse
when i get home i will keep trying, but not sure if its gonna work, i´ve never had that error with adb

[Q] Stuck in AT&T Screen boot loop, can't get into either recovery or download mode

[Q] Stuck in AT&T Screen boot loop, can't get into either recovery or download mode
I went back to stock (or tried to) and after Odin was done the phone just stuck in the AT&T boot loop, download mode is not working (it was working before so I know I am doing the right combination/timing) doing endless combinations of Vol-/Vol+/Power doesn't seem to get me into recovery mode-
I put my girlfriend's captivate on Continuum over the weekend so I'm sure I'm pressing the right keys to get into download mode, but I get nothing but the battery.
I do have the Android SDK in my computer but I'm never able to get past that naggy screen, so I can't do a 'adb shell reboot recovery' is a JIG my only option?
To recap, can't get into download mode and pressing volume up / volume down and power buttonuntil the AT&T screen and then release the power button doesn't get me into recovery mode.
Need help!

I've been in the exact same situation.A jig is most probably the only option.
Many people have had this problem and find that a jig is the answer.
Sent from my cappy UC'd 900mhz and UV'd running di11is rom/ Onix kernel

first try with just holding vol buttons and then inserting USB cable...hold vol buttons till its goes into download mode or the screen changes..if not then try following steps...
1. remove the usb cable, battery, sdcard, SIM.
2. wait 10 seconds, then insert the USB cable.
3. press and hold the 3 button combo while you insert the battery
4. continue to hold until phone's screen goes black twice and release power button.
5. timing is critical, it may not work the first time. Keep going until you see the COM port is connected properly.
still no Dl mode..then buy a jig or make one yourself

Right so I'm download mode now, but every time I go back to STOCK I'm re-stuck in the same loop, seems that I can't get out of it.
I got into download mode with a JIG, but still can't see my phone from my computer, so I can't run the adb shell to get it to boot in recovery mode
I'd appreciate any help you could give me!

leopic said:
Right so I'm download mode now, but every time I go back to STOCK I'm re-stuck in the same loop, seems that I can't get out of it.
I got into download mode with a JIG, but still can't see my phone from my computer, so I can't run the adb shell to get it to boot in recovery mode
I'd appreciate any help you could give me!
Click to expand...
Click to collapse
Restart your computer, use a different usb cable, a different usb port. if that doesn't work, unistall the drivers and reinstall, restart your comp and try again.

For anoyone that might find this thread, Odin 1 Click didn't work for me, so I flash back into stock using Odin (not the 1 click version, another one), here are some links that proved to be very helpful (I ended up Flashing to Serependity 6.4):
http://forum.xda-developers.com/showthread.php?t=1031749
http://www.youtube.com/watch?v=Rdn5GoRjhn0
http://forum.xda-developers.com/showpost.php?p=10056254&postcount=36
http://forum.xda-developers.com/showthread.php?t=884364
http://forum.xda-developers.com/showthread.php?t=919816
http://android-roms.info/roms/80-Serendipity
http://serendipityrom.weebly.com/download.html

I had the same problem just a few weeks ago.
The problem is once you start using 2.2 you can't use ODIN 2.1 anymore.
This is the one that worked for me I897UCJI6-OCD-REV02-Low-designgears(1)

Frawgg said:
I had the same problem just a few weeks ago.
The problem is once you start using 2.2 you can't use ODIN 2.1 anymore.
This is the one that worked for me I897UCJI6-OCD-REV02-Low-designgears(1)
Click to expand...
Click to collapse
this is actually a false statement.
i can still use odin 2.1 after flashing 2.2 roms and even stock 2.2 upgrades

Anyone thought about trying Heimdall if Odin doesn't work?

Yes, i tried using heimdall and that didn't work. I'm wondering what leopic did to fix his, if you could list the steps instead of the links that would help a lot!

stuck in att screen and battery loop
so i have tried searching for threads that match the issue i am having and some of them do and some doent so i have decided to post this. i tried flashing back to stock from a custom rom i was using. i used Odin to do this. i didn't work so i tried it again, same result. it dosent boot just sits at the captivate splash screen. i tried using a different oden tool and after that it just loops through the ATT splash screen and if i have the usb cable plugged in, it just loops the battery screen. im not even sure if it charges. i have tried everything i can find to do to get the download mode to come up and nothing, just loops. i have not tried the jig on this phone yet b/c i haven't made it to radio shack yet to pick the resistors up. is that going to be my only option?

what rom WERE you on?was it cm7 or miui?

Connection Issues? < click here for information on download and recovery mode....
information you should have had BEFORE FLASHING your phone..

i was on serinity 6.2.
i have tried all possible ways to get into d/l mode that i have found

so from the link provided
FROM A POWERED-DOWN STATE - BATTERY REMOVED
- Insert battery, then press and hold Vol+ and Vol-, then insert your USB cable..
goes into battery loop
- Press and hold Vol+/Vol-, Insert Battery, Insert USB cable
goes into battery loop
- Press and hold Vol+/Vol-, Insert USB cable, Insert Battery
goes into battery loop
- Use a 301Kohm jig between USB pins 4-5 (can be manufactured jig or homemade chain of resistors)
have not tried yet

asorendo said:
so from the link provided
FROM A POWERED-DOWN STATE - BATTERY REMOVED
- Insert battery, then press and hold Vol+ and Vol-, then insert your USB cable..
goes into battery loop
- Press and hold Vol+/Vol-, Insert Battery, Insert USB cable
goes into battery loop
- Press and hold Vol+/Vol-, Insert USB cable, Insert Battery
goes into battery loop
- Use a 301Kohm jig between USB pins 4-5 (can be manufactured jig or homemade chain of resistors)
have not tried yet
Click to expand...
Click to collapse
Sounds like a jig is in your future.

YAY. i got the resistors hook it all up and download mode loaded up. AWESOME!!!

viny2cool said:
first try with just holding vol buttons and then inserting USB cable...hold vol buttons till its goes into download mode or the screen changes..if not then try following steps...
1. remove the usb cable, battery, sdcard, SIM.
2. wait 10 seconds, then insert the USB cable.
3. press and hold the 3 button combo while you insert the battery
4. continue to hold until phone's screen goes black twice and release power button.
5. timing is critical, it may not work the first time. Keep going until you see the COM port is connected properly.
still no Dl mode..then buy a jig or make one yourself
Click to expand...
Click to collapse
You safe my Note.. Many Thanks
I thought I lost her x_x

I had this problem before
Users - I am new on this forum and I know this thread is old however I had this problem and it resolved itself. Here is how.
Background: I tried to charge my ATT Captivate using a Nokia microUSB charger that was plugged into a 120v outlet. After a few minutes of charging, the phone would no longer boot past the ATT World Phone screen. Afterwards I tried everything under sun to get a computer recognize the phone so I could reflash the ROM. Nothing worked (different computer, different USB cables, reinstalled the Samsung drivers, etc....).
Resolution of Problem: As a last ditch effort, I tried charging my phone with the same Nokia microUSB cable that appeared to cause the problem in the first placed. This time the Nokia USB cable was plugged into my computer instead of the 120v outlet. My computer had the Samsung phone drivers installed. To my amazement the phone booted up after I unplugged it from the USB cable and all is well.
I am not sure what happened but my Captivate is back with no damage. Hope this helps some poor soul who is trying desperatley to get a computer to recognize a phone that for no apparent reason will not be recognized.

Captivate not working after flashing CM10 nightly
HELP, Actually I rooted my SAMSUNG CAPTIVATE I897 and then tried to install CM10 nightly thorugh Clockwork mod recovery. And I forgot to wipe Dalvik cache. The phone got stuck in AT&T Screen for hours together, the phone was not at all responding i.e. neither to download mode or recovery mode. But yesterday the phone went into download mode .. i tried to install the stock rom for Samsung captivate. Its coming till galaxy S screen after that its switching off ... What is the possible solution. Pls Help with this as I am complete novice to this. Help will be appreciated :good:

ICSSGS Brick - Help Wanted

~ Started with Froyo 2.3.X (?), on a Rogers Phone
~ Tried to install Clockwork Mod - FAIL - 3e error.
~ Read solution - ODIN back to 2.1. (I897UCJF6-final-OCD-REV0)
~ Discover - with no warning mentioned in "guide" - that I have lost the 3-button functionality...
~ Recovery Mode / Download mode no longer accessible. Phone booting as ATT now, but fully functional.
~ Teach myself Android SDK. (N.B. adb no longer located in tools dir of SDK, installed from addt'l pkgs) - reboot requires Root?
~ Root phone with SuperOneClickv2.3.3-ShortFuse.
~ c:\android\platform-tools\adb shell
$su reboot recovery
~ Phone installs CWM no problem.
~ Buttons work on next reboot and bring up CWM. Factory Wipe, Wipe Cache, Wipe Davlik
~ CWM to install ICS_4.0.3.0(RC2.11)_Captivate_Full.zip
(ROM FIRST, fully intending to follow up with the kernel as instructed)
~ Boot Loop - Rainbow Squares flushing down a toilet. Buttons don't work again. Can not get to Download or Recovery or CWM (3 hrs now)
Whats next? please no soldering...

... OP states it will bootloop. You need to flash twice. You also should get GB bootloaders since it fixes your 3button issue. Get back in download mode. Doubt this will work but try:
Remove battery
Open Odin
connect phone to computer
Press Vol up+VolDown +insert battery
Use ODIN.
If it doesn't make/buy a jig and next time READ more before you flash.

For download mode, I always:
Start ODIN and plug USB into computer
1. pull and replace battery
2. with phone off, hold both volume buttons (if froyo based) or volume down (GB)
3. Plug USB into phone. see download mode
this ahs worked 100% fo the time.
if the battery icon pops up, then it do the other volume button....

pickupman66 said:
For download mode, I always:
Start ODIN and plug USB into computer
1. pull and replace battery
2. with phone off, hold both volume buttons (if i897 Froyo & gb based) or volume down + power if I9000 gb
3. Plug USB into phone. see download mode
this ahs worked 100% fo the time.
if the battery icon pops up, then it do the other volume button....
Click to expand...
Click to collapse
Fixed
Sent from my ICS powered Captivate

could have at least fixed the spelling too :-/
thanks though, but on item 2, I never touch the power button. just plug in the cord.

Thanks
prbassplayer said:
... OP states it will bootloop. You need to flash twice. You also should get GB bootloaders since it fixes your 3button issue. Get back in download mode. Doubt this will work but try:
Remove battery
Open Odin
connect phone to computer
Press Vol up+VolDown +insert battery
Use ODIN.
If it doesn't make/buy a jig and next time READ more before you flash.
Click to expand...
Click to collapse
Hey PR,
Thanks for the responses, I did read a lot, but did not see it mentioned anywhere that I could lose button functionality, and thus be prevented from getting back into download mode for 2nd flash.
Any ideas where I can buy a jig?
Thanks

The rom doesn't make you loose 3 button, Flashing to a very old JF6 did that. Google layman jig for a how to or google mobiletechvideos.com to buy one.

Just curious, did you try adb reboot download while the phone is booting? It should get to a point where it responds to adb commands. Hell, mine has been stuck on the ATT screen and still responds to adb. Worth a shot.
Sent from my SGH-I897 using Tapatalk

[Q] Phone not booting, warning logo

Apologies if this has been answered a hundred times but I upgraded the wife's Galaxy S to ICS but it lagged too much. The Kernel that was on it wouldnt let me flash Darky again through recovery so I tried to put stock back on via Odin and this happened.
I dont know the terminology so apologies if this is an issue with a name that I don't know, hence the picture.
Is there a way back from this?

Happened to me also when i unpluged while executing pit file.. Just if you still able to go to download mode, try flash with odin again. Worked for me. If you get any problems reply then
Sent from my GT-I9000, yeah Galaxy S one

Buy a USB jig off Amazon for a few dollars. It'll take you into Download Mode if you can't.

Before buying a JIG, try this:
1. remove battery
2. connect phone with computer via usb (without battery)
3. then press 3-button combo for download mode
4. while pressing these 3 buttons (phone is still connected to pc) put back your battery (for example using your nose )
Worked for me already a few times! If it won't work for the first time, try again and again..

Ajoslaf said:
Before buying a JIG, try this:
1. remove battery
2. connect phone with computer via usb (without battery)
3. then press 3-button combo for download mode
4. while pressing these 3 buttons (phone is still connected to pc) put back your battery (for example using your nose )
Worked for me already a few times! If it won't work for the first time, try again and again..
Click to expand...
Click to collapse
You my friend are a god damn legend! Im in DL mode