I am looking for people who have tried the p920h baseband and have had issues either with the respective lg software or using the cyanogenmod p920 build with it. I seem to get issues with the radio. It stops working and I can no longer receive/send calls or texts. I must reboot the phone. I am using the mexico bb with cm7 p920 build. It happens a lot at home where 3g signal is low and I switch between 3g and edge. This never happened with the stock froyo baseband.
Any feedback would be great.
Maybe this is why at&t is holding up our gingerbread update?
There is a video on you tube with an Aus user with the same problem, needs to reset his phone and then he gets full signal
http://www.youtube.com/watch?v=kCdQV8LpIIk
Related
I use Captivate with JH7 + SRE 1.3 + lagfix and I can't call when it is 3g but not EDGE
Calls just drop
But income calls are fine
Maybe it's because this phone's 3g is 850/1900/2100 and in Russia it is just 1900/2100?
How to fix this?
JH7 has issues...and the lagfix can cause issues with JH7. The posts ive read in development do not seem to specify what issues JH7 has.
If everything was working on JF3/JH2/JH3 I would flash back and wait for the next stable release.
I just force 2g now, I am ok without 3g and battery consuming is less
waiting for froyo official release
For quite some time now, my phone has been having some terrible 3G connectivity issues.
It just drops from HDSPA to UMTS and gives me no data for chunks of time. And every now and then, the entire 3G turns off(as if the APN has been switched).
This has been occurring with MIUI 2.2, MIUI 2.3, CM6 and CM7.
Im using 5.12.00.08 radio (latest i think). Im unsure what HBOOT I'm running, but the full baseband version is "32.50.99.32U_5.12.00.08". So i think I'm running HBOOT 32 but im not sure. With the CM and MIUI roms the problem was occurring on stock kernels and monk's.
Any ideas on what could be causing the issues? If you would like me to send logcats i can(i haven't seen anything in there to indicate any issues)...
Also i found a post:
http://forum.xda-developers.com/showthread.php?t=931728
Not sure if thats related.
Seemingly the problem started occouring after i was using alot with WiFi Tethering with Wireless Tether by Lemons and co.
I'm using Virgin Mobile AU as carrier.
Also, the problems occurs before installing ANY apps as well(and afterwards obviously).
32.50.99.32U_5.12.00.08
mine is only 32.50.00.32U... IMO just try flashing a new radio, start with 5.08 instead of 5.12 and see if that works then if you are content then leave it... else flash 5.12 after and try to root out the problem...
cheers!
The default setting in nexus one is WCDMA preferred... i.e. it connects to 3G if available.
If the signal strength of the 3G network is lower than than 2G network,
it switches to 2G rather than connecting via 3G.
However, Its a known limitation that Nexus one 3G reception is comparatively less due to physical properties of the antenna.
Hi guys, just a quick question for you Motorola Milestone users that use Vodafone's network in New Zealand.
First off, I know that Vodafone NZ does not support Milestone. Only Telecom XT supports it. However, Vodafone does support and sell Milestone 2, so I don't see why this couldn't be possible.
Anyway, I'm currently using Android v2.1 (Eclair). I flashed the New Zealand v2.1 SBF on it, and it works fine and all except it's obviously for Telecom XT, therefore I can't get my Vodafone SIM card to work properly. If I change the network from 2G to 3G, then it works. I don't get full signal bars (4 bars), but I get 3 bars most of the time which is pretty stable so it's not bad. However, if I switch to 2G (to save battery) then I get no bars at all, completely empty. It doesn't seem to be able to detect any network at all when I switch to 2G. Whereas switching to 3G the phone is able to detect all 3 networks in New Zealand (Vodafone, Telecom, 2Degree).
Now the reason why I'm on Android v2.1 is because when I was on v2.2 (Froyo), it has all sorts of problems with the WIFI. It's probably because of the kernel or something, and it seems A LOT of people have the same problem with me on v2.2 as well. If you do a quick Google search on wifi problems on Milestone then you'll understand why. A lot of people have suggested to flash back to v2.1 to fix this, and so I tried and it did indeed work for me. But since the only available SBF for v2.1 for New Zealand is for Telecom XT, now I have this new problem to deal with. It's not a big deal, I can stay on 3G. But if possible, I'd rather not because it seems v2.1 uses up battery more qiuckly, and the fact that using 3G uses more battery means I have to charge often and that's something I hate doing.
Now here's an important note. When I received my Milestone which came with v2.2 (Froyo) pre-installed, it was using Europe/UK I believe. It doesn't have problems with Vodafone's network on 2G at all, however like I mentioned it does have problems with the wifi. But the point is, the 2G network for Vodafone works fine on it.
So ya I'm just wondering, are there any Milestone users out there that flashed a different SBF, say Europe for example, and able to get the Vodafone network to work fine on 2G, while also making wifi work fine as well?
Or, are there any basebands for New Zealand that I can flash? There doesn't seem to be any from what I found.
Oh and here's where I found the SBF files in case you're wondering, here's the link for v2.1 (Eclair):
http://and-developers.com/sbf:milestone
and here's the link for v2.2 (Froyo):
http://and-developers.com/sbf:milestone221
Hi everyone, noob here so dun wanna start a new thread with my question since it is related to this matter and I was wondering if anyone can help me because I really can't figure it out anymore.
I have an International GT-i9000 purchased with Hong Kong and system specs I have running are
Gingerbread.ZSJW4 (recently flashed the official ROM from Hong Kong cuz I am anal and want to keep the same languages)
Kernal: 2.6.35.7-I9000ZSJW4-CL1147074
[email protected] #2
Bandbase version: i9000ugkg3
And I use AT&T in New York (I know, worse plan to use in dead zone capital of the US)
I had flashed the ugkg3 modem on it because the JW1 modem that was with the official ROM wasn't working out for me and I had heard this modem was the best for my area. Before it would either not pick up a signal when coming up from underground or the signal just go dead, which did not happen when my phone was on Froyo (on Froyo I did not have 850mhz enabled and it worked alright outside and sometimes in the house)
At first, the KG3 modem worked wonderfully, I was able to receive data in my house and was on 3 bars (compared to none to one before). However, I now notice that while I do have full bars, I cannot receive or send messages or phone calls (even though my brother's Note is able to do all that and it was next to my phone).
I also happens when I am outside as well.
The other day I was standing in front of the AT&T store near where I am and I still don't pick up a signal.
Or it would lose the signal and never pick it up again.
Unless if I really can't use 850mhz on my phone, which does not make sense because AT&T uses 850mhz.
I am real hesistant to try another modem, and I cannot figure out if it is a hardware issue or network issue, or is it just the wrong modem?
Can someone please share any insight?
Radio GSM / Módem:
KF1 (Perfectly Changes 2g to 3g)
use this
kzkan said:
Radio GSM / Módem:
KF1 (Perfectly Changes 2g to 3g)
use this
Click to expand...
Click to collapse
works in ATT?
kzkan said:
Radio GSM / Módem:
KF1 (Perfectly Changes 2g to 3g)
use this
Click to expand...
Click to collapse
my other question is, phone is not ICS, and I found the nexus S one...will it still work?
and can I just extract out modem.bin and flash via ODIN ?(somehow my phone won't do CMW recovery...)
Hello, I just purchased an unlocked HTC One M7 to use on Rogers. LTE works 100%, HSPA works 100%, 3G works 100% (meaning I can use the data flawlessly). HOWEVER, I cannot make or receive any phone calls if I am in GSM/HSPA/LTE mode.
When I call my phone while in LTE mode, I can see my phone switching from LTE to HSPA/3G immediately (that's supposed to happen since calls cannot be made over LTE atm) but the phone does not ring at all.
IF I put my phone in GSM/HSPA mode, then incoming/outgoing calls work flawlessly... if I switch back to LTE mode I can't make/receive phone calls anymore. I know for sure it's the LTE mode cuz I tried 4-5 times switching back and forth between GSM/HSPA/LTE to GSM/HSPA only mode and phone calls ALWAYS work under GSM/HSPA and RARELY work under GSM/HSPA/LTE (a couple times it did go through but 95% of the time it doesn't work).
I tried flashing a new modem, a new ROM and everything but it's still the same problem.
Does anyone have any suggestions? Thanks!
EDIT - Just noticed that calls stop working in 3G mode too until I restart the phone
EDIT 2: Alright, from going through *#*#4636#*#* I've isolated it down to HSPA+. Phone calls ONLY work on HSPA+ and not when it's on 3G or LTE. Any ideas?
Flash a full ruu ?
My phone does this as well. but i dont have any problems getting calls or sending calls. If using LTE it drops to 3G while on the call. Though my phone is screwed and i never get HSPA+. Really wish there were more Bell users around.
I experimented all day yesterday with several different roms, downgrading down to JB back up to KitKat, tried a few different modems but still nothing calls ONLY work on HSPA.. u think it's a defective radio or something? my phones not under warranty either is there a way to get it fixed
i think its the firmware not matching up with radio. or having the wrong radio all together. I cant get S-off so its made it a pain in my ass. Ive pretty much given up hope lol. I could take my phone back to sense 5.5 stock with a nandroid that i have and everything works normal but i like sense 6 so ive just learned to deal.
if i could get any of the latest Bell or Telus radios it may be a help.
Howie3045 said:
i think its the firmware not matching up with radio. or having the wrong radio all together. I cant get S-off so its made it a pain in my ass. Ive pretty much given up hope lol. I could take my phone back to sense 5.5 stock with a nandroid that i have and everything works normal but i like sense 6 so ive just learned to deal.
if i could get any of the latest Bell or Telus radios it may be a help.
Click to expand...
Click to collapse
With your issue, phone dropping to 3G while on call it is normal because right now there is no voice over LTE. So the phone has to drop down to the either HSPA or 3G, whichever one is available.
and yeah you might be right about not having the right modem, but I can't find a Rogers modem ANYWHERE. The only one I found was part of a RUU to get back to stock if anyone has even an oldd Rogers HTC One M7 radio, please please please post a TWRP/CWM flashable version of the modem lol