I hace a problem with the USB contact, and it is that its too sensitive and if i move it a bit it disconnect
It seems that i can move te USB connector once its plugged un
Anyone knows if this is normal? Do you think i have ti get ir repaired?
Many thanks
Sent from my GT-N7000 using xda premium
I had this happen with my old HTC Desire and I found it was the USB lead that was responsible, the little teeth that stick out either side had become stick inside the end metal casing, just ended up getting a new cable.
This was my problem though, check the cable by plugging into something else and see if it's still loose before you go buying new one straight away.
Related
Whenever I'm charging my captivate. The charger is loose and does not stay tight.
If I move the charger a little bit, it stops charging or recognize it as USB...
I'm using the standard charger that you get along with your captivate.
Are anyone of you experiencing the same problem? Is there a solution?
Sent from my phone
bluemoon1221 said:
Whenever I'm charging my captivate. The charger is loose and does not stay tight.
If I move the charger a little bit, it stops charging or recognize it as USB...
I'm using the standard charger that you get along with your captivate.
Are anyone of you experiencing the same problem? Is there a solution?
Sent from my phone
Click to expand...
Click to collapse
Same thing is happening to me, I don't k ow why.
Sent from my GT-I9000 using Tapatalk
I found this usually only happens when the door covering the usb port isn't opened all the way. Make sure yours is open all the way.
Make sure u slide the charger cover all the way open is only thing I can guess might be wrong
Make sure the sliding door is all of the way open. It tends to stick, and then the connector doesn't click in place. If the door is all of the way open then the connector will stay in place firmly.
Sent from my SAMSUNG-SGH-I897 using XDA App
Yeah that's the normal issue (the door not clicking open). Also, the stockcharger has little hook/protrusions that tends to hold it a bit better as well.
I always had my sliding thing fully opened.. the charger just doesnt seem to stay in place.. for ex. When my phone is on the ground charging, and if i pick up my phone, the charger tilts to the left which causes my phone to think its a usb..
Should i just get another charger? Any recommendation for one?
Sent from my phone
Yep, my OEM charger eventually became so loose that it would fall out unless the phone was propped up vertically. I read about crimping or adjusting the socket itself with needle nose pliers, but this didn't work for me. The only solution I found was to purchase another micro USB cable. So far my third party ones all fit fine.
Sent from my SGH-I897 using XDA Premium App
yeah likely the door or the cable
I think it's partly the Samsung adapter and MicroUSB in general. Mine's not that bad, but third party ones do seem to hold better, if not as well as some other connectors.
Its the stock adapter you get with the phone. After a while the prongs wear out. Third party chargers are excellent and a made more heavy duty and tight fitting. Thus they last longer.
Sent from my SAMSUNG-SGH-I897
I am having the same problem and I know for a fact that the door is open I think I have another USB around so I will have to give that a try.
Sent from my SAMSUNG-SGH-I897 using XDA App
Hy,
My phone has a problem after I unplug the charger it still loads.:crying:
Take that sound like they still load.
Mention that run Android 4.0.4 N7000XXLRB and took root.
Help me or advise me please as I do to get rid of it!
Thank you!
Just try to clean ur micro usb port using a toothbrush and some perfume or alcohol, some dirts may cause this,
↖(^▽^)↗ Sent from Rego Galaxy Note ↖(^▽^)↗
push the usb pins straight back inside the phone with a plastic fine tool. this will set the pins inside the usb post and phone will work fine. make sure the after-,market cover is not hindering with the charging cable when connected to the phone. I cut my cover's hole bigger so my cable can connect. it was bend slightly because the cover's opening for the charging port was not sufficient enough. My micro usb cable was connecting with an angle. when I made the cover opening bigger and used a new cable and pushed the usb pins back inside the phone, all went fine from there on.
Happened to me 2 what people told in the 2 post what helped me try it hope that fix it
Sent from my GT-N7000
Try the wiki
See if you have this problem. Unless you have macro vision, you will need a powerful magnifying glass, or loop.
http://forum.xda-developers.com/showpost.php?p=25102882&postcount=18
Resolved!
I resolved and I followed the advice of aftabbabar. Thanks!
Had this problem too
Sent from my GT-N7000 using xda premium
Any one know of a company that can fix the USB port on a HTC Raider in Canada. Rogers wants to charge me $250 to fix it.
KillerbawX said:
Any one know of a company that can fix the USB port on a HTC Raider in Canada. Rogers wants to charge me $250 to fix it.
Click to expand...
Click to collapse
You could probably buy two new Raiders for $250! Replacement might be the best bet, as you can likely find one on Kijiji for $100 or so. If you have a local cell repair joint, give them a call, and see if they offer the replacement. It might be tricky since the USB on the Raider (as other HTC phones) is actually a special type of HDMI jack that also has USB (known as MHL).
If you're adventurous, you might track down a broken Raider and attempt a part swap yourself. I've not seen the inside of the unit, so I can't say how easy or hard that would be at any skill level...
Hope you get it fixed up!
The part is on eBay you can always try to do it yourself should be a few small solder points
Sent from my HTC PH39100 using xda premium
KillerbawX said:
Any one know of a company that can fix the USB port on a HTC Raider in Canada. Rogers wants to charge me $250 to fix it.
Click to expand...
Click to collapse
A friend needed this. We ordered one off ebay ( http://www.ebay.com/itm/OEM-USB-Pow...328529?pt=PDA_Accessories&hash=item27c422a1d1 ) and although it required opening the phone up and voiding the warranty, it required no soldering. He doesn't open electronics up very often, and said it wasn't very hard to do.
i was babbling abt this in a thread in the dev forum, thot i'd best do it also here in the proper forum for it:
i changed the USB port in my Raider, was very simple. Six little screws, two different lengths so keep track of them. One screw also holds down the teeny cover under which is where the tiny connector resides that connects the port to the fone circuit board. Once the fone is back together that's where you make the final connection between port and fone.
Slip off the battery cover, undo the six screws, take off that tiny little cover. Carefully work off the entire back housing. There's no front housing, just the screen glass and the fone circuitry bundled together.
Micro-USB port and ribbon connector is fastened to the housing with two more of those little screws. Change out the port with the new one. New part may not be an exact duplicate of the old part: that's ok. Reassemble the fone. Under that hole left by the tiny cover, press home the miniscule plug that connects up the port to the fone.
Put back the tiny cover, fasten back all the screws, and you're done. Port cost me $9 USD plus shipping on ebay.
lowfatmilk said:
i was babbling abt this in a thread in the dev forum, thot i'd best do it also here in the proper forum for it:
i changed the USB port in my Raider, was very simple. Six little screws, two different lengths so keep track of them. One screw also holds down the teeny cover under which is where the tiny connector resides that connects the port to the fone circuit board. Once the fone is back together that's where you make the final connection between port and fone.
Slip off the battery cover, undo the six screws, take off that tiny little cover. Carefully work off the entire back housing. There's no front housing, just the screen glass and the fone circuitry bundled together.
Micro-USB port and ribbon connector is fastened to the housing with two more of those little screws. Change out the port with the new one. New part may not be an exact duplicate of the old part: that's ok. Reassemble the fone. Under that hole left by the tiny cover, press home the miniscule plug that connects up the port to the fone.
Put back the tiny cover, fasten back all the screws, and you're done. Port cost me $9 USD plus shipping on ebay.
Click to expand...
Click to collapse
Hey, dude, I know this thread is a little old, but can you PM me the link to where you bought your USB port? I think I need to replace my port (issues connecting to PC and charging requires wire wiggling), but I've read about certain ports not working with data transfer and only charging, and I don't want to make that kind of mistake.
projectisaac said:
Hey, dude, I know this thread is a little old, but can you PM me the link to where you bought your USB port? I think I need to replace my port (issues connecting to PC and charging requires wire wiggling), but I've read about certain ports not working with data transfer and only charging, and I don't want to make that kind of mistake.
Click to expand...
Click to collapse
Try this? Says OEM so I imagine you wont lose functionality.
http://www.globaldirectparts.com/product-p/htc747235-qs.htm
Thank you! And only $8 too
Sent from my Vivid 4G using xda app-developers app
The male pins on the bottom on my Touchpad are broken (fell while it had a charging cable in it and of course landed right on the cable/port)
I can charge with a Touchstone charger just fine, but I want to use things like AcmeInstaller v3 and AcmeUninstaller, so I have a few questions:
1) I've looked at videos of how to take it apart (it's not under warranty anymore). Does anyone have experience with this and can relate to me how hard it actually is?
2) Does anyone have or know where I can find the USB port/daughter board that goes inside? I know it can be replaced, and I can find broken Touchpads on eBay but thought I would ask here first.
3) Is there a way to use Acmeuninstaller and AcmeInstaller v3 without being plugged into the computer via USB? (I'm figuring the answer is 'no' but figured it can't hurt to ask)
Thanks in advance for any help!
Re question 1 replacing USB board , there is a step by step guide with photographs in the iFixit app available in play store or from there website.
Thanks sstar! Found the guide here, now just have to find the part or a broken Touchpad on the cheap
Yeah, its super easy to remove. Parts, not so easy to find...
Sent from my SAMSUNG-SGH-T989 using xda premium
Opening it is easy but still terrible. The clips are horrible, I ended up breaking nearly all of mine.
That's what I'm worried about. Any tips? How do you keep yours together now?
Sent from my XT901 using Tapatalk 2
Omg... just looked at that link for how to do it, and that's terrible. Lol. I use butter knifes and can still do a more sensible job of it. You can release the clips even before you pry up.
Sent from my SAMSUNG-SGH-T989 using xda premium
Badger48 said:
The male pins on the bottom on my Touchpad are broken (fell while it had a charging cable in it and of course landed right on the cable/port)
Click to expand...
Click to collapse
hahaaahaahahah mine fell like 5time on the ground on the usb port. from my bed.
and today it wont charge any more, i think he fell to many times. sucks, cause he didnt fell yesterday i think, but yeah, i guess im fuked now, he charges but so slow..... na i must say my tablet looks like he did the 2nd world war, the plastic is broken alost in every corner..
Any one a link for thr usb board?
I have another microUSB cable but it slips out sometimes, and doesn't charge the Nexus 7 unless you hold it at certain angles. If anyone can point me in the direction of getting a replacement ASUS micro USB cable like the one that comes with the Nexus 7, or even one that people have found is a snug fit with their devices,and isn't prone to falling out, please let me know. Thanks for the help.
You don't say where you are but if you can find something like this you should be fine. http://www.amazon.co.uk/LINDY-Degre...26&sr=8-3&keywords=micro+usb+lead+right+angle
Good length and the right angle plug make it less likely to catch on things.
Troute,
Do you use this with your Nexus 7? Because I've heard that some microUSB cables' pins on the connector aren't long enough to reach into the Nexus 7's and that's why the microUSB cable I'm using now is so flimsy. Do you know anything about that?
Theoretically It must work, because the OTG cable we are using is micro USB B to USB female.
I think some people must got their cable from a bad store that cause the defect you're talking about
I use whatever lead is handy and have had no problems but I avoid buying cheap chinese ones. Problems can be caused by a combination of badly made/loose plug and a loose socket