Related
PLEASE HELP: Calling all experts!!!
After installing the: [STOCK ROM] Odin3 One-Click Downloader and Drivers CAPTIVATE ONLY
My Galaxy S 19000 is stuck on the at&t boot screen.. the at&t logo just keeps flashing...
I cannot get into download mode...
PC is not recognising phone via Kies, odin or anything else...
Something tells me I have made a huge mistake somewhere along the line.. any fix???
Thank you
If no recovery/download mode working...
Only UART/JTAG, check on progress on this.
Thank you for your help...
Quite expensive options aren't these, GOOD THING I HAVE INSURANCE!!!
There must be a software way around this thou...
HELP!!!!
If your phone can't get into download mode due to it being disabled it looks like your pretty much screwed. You could phone samsung and see if they'd fix it.
Sent from my GT-I9000 using XDA App
If you can get to the AT&T logo part, I'm assuming you should still be able to get to download mode. Did your phone have dl mode before?
Thread moved to Q&A section
Yes my phone could get into dl mode b4 but now it doesn't work any more, phone just keeps on showing at&t logo and rebooting.
When I put the USB lead in the phone does not switch on at all..
thanks 2 all for assistance in this horrible mess negligence has left me in.
the USA models goes into download mode by using the volume up + volume down + power
see if that works
Thanks for your reply...
no joy... any other viable button combinations I could try? I've already tried many to no avail...
I'm no expert on the matter but don't you think that since you flashed a Captivate ROM on an I9000 that the home button wouldn't work since the Captivate doesn't share the same home button? Logically I would try looking for what the combo is for the Captivate to get into download or recovery mode. Now, I may be wrong and it may not work if the captivate uses its home button to enter the home button but it's worth a shot.
Edit: I just checked here and it says you hold both the volume up and volume down button while you press the power button. Try that.
With the device off, try holding both vol + & - then plugging in usb cable. Thats how a captivate enters download mode. If flashing the i9000 on captivate changes the button sequence it could not hurt to try.
Sent from my SAMSUNG-SGH-I897 using XDA App
@ Bell & foom....
I understand both your thought pattern and YES this was mine also...
However thus far no combinations have worked, still continually looping the at&t logo.
If I plug in the charger or USB whilst its doing this it kills the device, it wont switch on...
Knowing the different CAPTIVATE button comb. to recovery or download mode would be a big help right now.. also how the buttons would be mapped... i.e Captivate rom. on GALAXY S device?
How would one fix a captivate that was continually re-booting at operator logo start-up? Might be another way to angle this?
Thanks....
Think u are better off paying the guys at samsung or phone repair store to load the right firmware back in if u dont have the 3 btn combo...
Sent from my GT-I9000 using XDA App
try downloading that one click unroot program, plug the sgs into the computer and then force unroot, although the unroot won't work it should then allow the sgs to enter recovery mode.
Unfortunately my PC is not recognising the phone...
Plugging the USB in while the phone is switched OFF does nothing....
lugging the USB in while the phone is switched ON.. Turns it off...
Same things happen when the Charger is plugged in.. Althou the phone seems to still charge!!!
Arghhh..
Thanks for your suggestion thou.. Any more help/ ideas are welcomed...
Last resort maybe try heating up the phone like the others did to force download mode?
Sent from my GT-I9000 using XDA App
so any news on this? i too have successfully flashed the captivate rom on my unbranded i9000 the official repair shop i first took it to (mttc <Lithuania>) told me that it needs a new motherboard, and it would cost me 700LTL(270 $us)... kinda sounded like bull****, so a week ago i took it to a private repair shop, they said they had jtag, so i should be hearing from them this week, if not, i'll buy the stupid riff box myself and repair it..
no button combination worked for me, and the symptoms were exactly the same, flashing att, usb kills it etc. etc.
well, my advice would be to keep contacting different local repair shops, and asking do they have a jtag that supports the samsung galaxy s, if they do, the repair shouldn't cost more than 25$, at least thats what I've been told. good luck, and stay in touch, update on your process, cause the number of people flashing the wrong rom on the i9000 is horrifying.
it kinda sux that its so easy to brick the sgs... and its wrong for people to state that "if you have 3button combo enabled, you are safe", well thats just bull****.
No GOOD news as of yet, but I am in the process of to admitting my SGS to a official samsung service centre.. I was also thinking of sending it directly to them for repair...
???
Still been trying some other things to try and jump-start this blasted thing in the meantime but NOTHING IS WORKING!!!!
I to am thinking about purchasing this riff box or JTAG but it would be for a ONE TIME USE only... Seems like a waste of money when I can just claim a new SGS through insurance only thing is playing the WAITING GAME!!!
I Shall definitely update this thread with any progress made in the coming days...
Here I was thinking I was a lone soldier with this dilemma...
Also I agree... SGS = Too easily bricked.. and no solution?? Other than splashing out 100+ £/$... in your words truly SUXXXXXXX!!!!
Konshens said:
Also I agree... SGS = Too easily bricked.. and no solution??
Click to expand...
Click to collapse
Sorry, but ANY phone (or even any electronic component for that matter) is easily bricked if you flash firmware from a completely different device onto it.
Electroz said:
Sorry, but ANY phone (or even any electronic component for that matter) is easily bricked if you flash firmware from a completely different device onto it.
Click to expand...
Click to collapse
well, afaik, its very hard to fully brick a new htc device.
anyway, i suggest you try finding a jtag repair shop first, as samsung will take a lot of time to "repair" it, or even tell you that it needs a new motherboard..
Hi,
My phone is stuck at the galaxy S screen... I was trying to get the 3 button recovery mode to get to work following instructions on this thread
http://forum.xda-developers.com/showthread.php?t=821698&highlight=button+combo+fix
the guy suggested to go back to recovery 2e which i did following instructions from this thread...
http://forum.xda-developers.com/showpost.php?p=9433417&postcount=287
After running the adbrecovery, my phone just stays at galaxy S screen, Its not going forward!!
Please help what should I do!!! Is my phone bricked???
use adb to boot into download mode.
flash a firmware with all 3 files and 512pit, check re-partition in odin and that should work
Thanks for your reply, but how exactly do i boot into download mode from adb... my phone wont go past the galaxy s screen, adb needs an active connection with the phone, if i'm not wrong...
oh yea..
so you dont have the 3 button combo ? recovery / download mode ?
yep i dont have the combo working, thats the reason why i was trying to get it to work!! is there still a way to get it work??
not without download mode, or recovery mode, i think your gunna need a JIG
JIG?? i'm not sure what that is... Can you please give me a link or any information on this JIG...
yea, a JIG is a usb cable with a resistor attached which forces the phone into download mode. you can make them your self or buy them of ebay and places like that.
they are life saving tools for recovering from bricked devices, more so for people without 3 button combo, like yourself
http://forum.xda-developers.com/showthread.php?t=819551&page=3
http://cgi.ebay.co.uk/Fix-Download-...ltDomain_0&hash=item20b79446da#ht_2910wt_1154
Thanks i'll give it a shot!! otherwise i guess there is no other option than to take this to the service center!!!
the usb JIG will work 100% all the time. its what they use themselves at samsung service centre.
it will force you into download mode allowing you to flash what ever you want.
if you take it to samsung and they find out you had customised it they WILL charge you, or refuse to fix it.
Hey man,
If you have Kies installed, hook it up to the phone and see if it will recognize it. If so, format your internal sd card. See if it will start up past the screen next reboot.
azzledazzle said:
the usb JIG will work 100% all the time. its what they use themselves at samsung service centre.
it will force you into download mode allowing you to flash what ever you want.
if you take it to samsung and they find out you had customised it they WILL charge you, or refuse to fix it.
Click to expand...
Click to collapse
Ya thats true, however my phone only had a lag fix installed and was rooted... No custom roms or kernels!!! Since it wont go past the boot screen, i'll have to assume that they wont notice that it was rooted... Although this is a very stupid assumption but i'll take my chances if i'm unable to come up with a JIG...
electrotune1200 said:
Hey man,
If you have Kies installed, hook it up to the phone and see if it will recognize it. If so, format your internal sd card. See if it will start up past the screen next reboot.
Click to expand...
Click to collapse
Tried that doesn't work... If it was recognized by my laptop i would have got into download mode using adb... but unfortunately it doesn't work...
oh yes totally, to be honest they will probably just jig it flash it with stock and send it back. they must do this loadsa times a day.
but there is a chance you will get some c**t who will dig deep to find the cause because he knows people like to hack android devices.
the chances are slim, but its still a chance at the end of the day.
another thing, a jig will be less than £10 and will save your ass many times.
service centre can take a full month, and if you hack it again and re-brick it, your back to square 1.
so even if you do send it to samsung, its worth looking into a JIG investment
azzledazzle said:
oh yes totally, to be honest they will probably just jig it flash it with stock and send it back. they must do this loadsa times a day.
but there is a chance you will get some c**t who will dig deep to find the cause because he knows people like to hack android devices.
the chances are slim, but its still a chance at the end of the day.
another thing, a jig will be less than £10 and will save your ass many times.
service centre can take a full month, and if you hack it again and re-brick it, your back to square 1.
so even if you do send it to samsung, its worth looking into a JIG investment
Click to expand...
Click to collapse
Yep true, however i highly doubt that a service center in India will dig deep to find the issue, Service center people are really really lazy and they are much more interested in workarounds than rootcauses...
And sure thing dude, I'll try to find a ready made JIG tommorrow... I wont be able to take it to Service center until saturday, so if i can manage to find it, I probably save myself the trip and ya as you said, i'll be much more confident customizing my phone the next time... Thanks for all your help... appreciate it...
Ok, heres the deal.
My girlfriend has the same Galaxy S as i do, and i wanted to go back to stock.
Id grabbed all the needed files off her galaxy (boot.bin, cache.rfs, dbdata.rfs, factory.rfs, modem.bin, param.lfs, sbl.bin and zImage) and loaded up heimdall to flash them all back.
The flash finished successfully, the phone switched off, and i awaited a reboot.
It never came.
The phone is now in a Non- Functional state, wont turn on at all.
The battery was fully charged at the time, and ive also pulled her battery out and tried it, but still no go.
Im thinking something inside is fried.
Just thought id share my misfortune with you, just in case someone else was going to try the same thing.
If you were gonna try....think twice
So i guess its back to Optus shop on tuesday, and see what i can do about a replacement.
Cheers all.
you shouldn't use boot.bin ,Sbl.bin and param.lfs. It is not safe to play around these files, you could dump other files and flash it,without any problem,
Ok, well maybe thats what has killed it.
Ive tried all key combinations, but nothing at all.
Pretty convinced its fried.
OzzYGuY said:
Ok, well maybe thats what has killed it.
Ive tried all key combinations, but nothing at all.
Pretty convinced its fried.
Click to expand...
Click to collapse
I did the same thing on my phone and happened so, but I took it to service center and they repaired without changing the board or opening it(this is what I think because there were no trace of any physical repair), anyhow its working again. but before you may try some methods which I read in some forum as below:
Remove everything from your phone (SD card, sim, battery).
Plug your phone into your computer WITHOUT the battery, as you have already taken it out in the last step.
Press and HOLD vol. up and vol. down.
As you are HOLDING these buttons, reattach your battery.
You should be in Download Mode.
there is another method which I will try to find and inform you
Thanks for the tip....but no go.
Screen still black....
Its like its not getting power at all.
Try and force it in to download mode [vol down - home key - power button] and then reflash it with a stock rom. If that fails then you could try holding just the power button in for a minute or 2 but if that also fails then your last option is to try and either get hold of a jig or make one to try and get it in to download mode.
Using the application Odin should fix this problem. as above said, about vol up vol down, im sure it is volume down,powerbutton and homekey when connecting to a comp when odin is open. Odin is ure failsafe. correct me if i am wrong with this information!
jonnyb
sean2476 said:
Try and force it in to download mode [vol down - home key - power button] and then reflash it with a stock rom. If that fails then you could try holding just the power button in for a minute or 2 but if that also fails then your last option is to try and either get hold of a jig or make one to try and get it in to download mode.
Click to expand...
Click to collapse
Ive tried all key combinations that we know.
Ive flashed it many times before, but i think this time after the flash, something has blown, in between the battery, and the power switch, so its not getting any power.
I think the only cure is to return to samsung for repair.
Ive tried everything that ive read from various google searches for the last 8 hours or so...and no hope.
Im almost positive theres no power getting from battery to the power switch.
Phone is Dead - A warning for others.
Yes follow instructions understand what you are doing first dont make it up as you go along .
I would guess you have destroyed boot loader .
Possible fix is download mode recovery jig .
Samsung service centre possible charge .
jje
Grabbing some resistors tomorrow, will see how that goes.
JJEgan said:
I would guess you have destroyed boot loader .
Possible fix is download mode recovery jig .
Samsung service centre possible charge .
Click to expand...
Click to collapse
If the Sbl.bin id non functional, the Jig can't do anything, you must use a RiffBox or equivalent sadly.
sad story, hope never will happen to me
If its still under warranty just go to samsung service centre and tel them you tried upgrading firm ware over the kies and phone did not boot after that. Its not easy for samsung to find what you did with the phone. they will replace mobo free if warranty is valid.
Sent from my GT-I9003 using XDA App
trip007in said:
If its still under warranty just go to samsung service centre and tel them you tried upgrading firm ware over the kies and phone did not boot after that. Its not easy for samsung to find what you did with the phone. they will replace mobo free if warranty is valid.
Sent from my GT-I9003 using XDA App
Click to expand...
Click to collapse
Yeah will do.
Mrs will take the phone in to where she bought it on tuesday, and see what the process is.
Phone still under warranty so i doubt ill have any worries getting it repaired.
Bought a jig this morning for $8.00.
Knew it wouldnt get my phone goin after reading that if the secondary boot loader was not intact that it wouldnt work. As id flashed the sbl.bin i knew it was toasted, but for 8.00, having a jig handy is worth every cent anyhow.
Have my Galaxy Tab to use as a phone untill the "S" is repaired, so thats a bonus.
Although im without a phone for possibly 2 weeks or so, i dont regret flashing it.
Its a good learning curve, and one ill remember.
At least i know now, that even though heimdal has slots for the bootloaders, DONT USE THEM
Its all good, and im not discouraged in any way from flashing it again as soon as its repaired lol.
All in all its been a good lesson learned.
Ive learned about the download jig, which of was unaware of earlier.
Thanks to all those who replied with info....i do appreciate it.
Will post back results of the phone return....when i know more.
Cheers
Thats the spirirt dude. I was in the same situation as yours. Got my motherboard replaced under warranty period, they took 2 weeks but were quite helpful. I said kies update bricked my phone. They replaced it for me. All happened within 2 weeks of the phone purchase. so it was bit tenseful situation. I own I9003.
Got my Galaxy back yesterday.
Turns out the main board was fried.
They replaced the board...and am now functional again...
Its the stock DTJP3 firmware.....but not for long LOL
Think ill leave heimdalls boot options blank from now on...better still, ill use Odin instead.
OzzYGuY said:
Got my Galaxy back yesterday.
Turns out the main board was fried.
They replaced the board...and am now functional again...
Its the stock DTJP3 firmware.....but not for long LOL
Think ill leave heimdalls boot options blank from now on...better still, ill use Odin instead.
Click to expand...
Click to collapse
hey..i have the same problem..going to svc tmmr...how long did it take?
hi iv had a serious journey with my sgs i9000 here's how it goes:
i had it on 2.2 and then upgraded it officially to 2.3.3
not much else happened until i realised i wanted voodoo sound (apparently it was hyped to be awesome....its not that great) and neither is the ext4 file system 2.3.3 seems to be just as fast...dont know if it was a major problem on 2.2 but it aint really on 2.3.3
so i flashed voodoo on 2.3.3 from some website ... downloaded the app for the sound as the kernel didnt support that...
then i was using it and played around with the settings in clock work manager and i mounted and unmounted sd/card i dont think it made much difference but i thought i'd mention it ... the reason i did this is because when i tried to load a rom it wouldnt find all my sd card files beyond like the first 5 folders so i thought i'd give it a kick start....
then what happened is the phone just went off and i couldnt get it back on.... little did i know this was soft brick... i didnt know why....
i got the computer screen with the phone and exclamation mark.... i got into download mode a few times....
NOW .... i cant get it to turn on AT ALL using any combo buttons....
i think the nail in the coffin was flashing it with the "one-click odin" which was for the captivate but it said i could use it on the i9000 too.... which blatently screwed up the device....
anyway iv ordered a jig device... if this gets me into download mode ....what am i supposed to do...?
also is there anything i can do to get it into download mode now ? (bearing in mind iv done all the combo's ... some people say leave the battery out for a couple of minutes or half an hour....)
i think the bootloader is screwed up because it doesnt switch on....
even after i did a clean install of 2.3.3 with the pda phone and csc roms... it still just randomly switched off after 2/3 minutes of boot time....
what do i do now ?
samsung repair centre said they couldnt do anything and i'd have to send it back to samsung.... is it that bad?
Tried all the combos.... So you tried plugging in combo, then battery and also holding combo and then battery without cable in...
Have you read the pinned thread in general i think it is regarding, bricks?
Moving on
how did you do a clean install of 2.3.3 if you couldn't get DL mode??
Haven't read into the one click Odin so can't comment on that, but i think that was meant to be for softbricks...
anyway regarding the jig, just plug it in, and then wait a second or so, of not a minute (usually instant) and it should go into download mode. If it doesn't work again try some combos with the jig in...
If it is a hard brick i think you need to J-tag it, or yes take it to samsung in which case they may charge you for a repair, unless you say kies did it, and you didn't tell them everything you didi when you spoke to em.
Think thats everything lemme know if i missed out a question of yours or you want something better explained etc..
yeah i guess i was vague on the combo thing...
i've tried:
a) holding power, menu and volume down while sliding battery in (no usb cable in )
b) same as above with usb cable in
c)just menu and volume down buttons while i put battery in
d) both volume buttons and cable in
e)both volume buttons and battery in
.... the reason for d and e is because when i flashed it with the one click odin installer thing.. it restarted and showed a a t&t screen so i think its flashed the software with a samsung capacitive rom....so in theory i need to use those buttons ? not sure .... yet more questions....
i just hope this jig thing works ... btw do i have to pay sammy is my phone is under warranty?
how do i reflash the bootloader so it works properly? is that even the problem? do i need to do that? which pit file do i use ? some people say 512.... some say thats outdated and the new pit file is the thing to use .. ?
Talon26 said:
Tried all the combos.... So you tried plugging in combo, then battery and also holding combo and then battery without cable in...
Have you read the pinned thread in general i think it is regarding, bricks?
Moving on
how did you do a clean install of 2.3.3 if you couldn't get DL mode??
Haven't read into the one click Odin so can't comment on that, but i think that was meant to be for softbricks...
anyway regarding the jig, just plug it in, and then wait a second or so, of not a minute (usually instant) and it should go into download mode. If it doesn't work again try some combos with the jig in...
If it is a hard brick i think you need to J-tag it, or yes take it to samsung in which case they may charge you for a repair, unless you say kies did it, and you didn't tell them everything you didi when you spoke to em.
Think thats everything lemme know if i missed out a question of yours or you want something better explained etc..
Click to expand...
Click to collapse
ok now iv got it to turn on quite regularly .... but it keeps cycling (bootlooping) the at&t logo screen .... cant get into download mode or recovery mode.... just keeps boot looping.... oh and when i plug in the usb cable it just turns off.... its like i cant start it up with a usb in the phone...
update: been reading around and if anyone has this problem.... it looks like you might be hard bricked and apparently this cant be resolved via jig device..... dammit ...i'll still try and update the post... peace
So you haven't tried the jig yet?? because you haven't got it yet right
I don't think the device is bricked at all. Bricked usually means you have no response from it, so no matter what combo, actions you take you get no reaction.. However you are getting a boot although there is something going wrong as it does so...
So yes you need a new bootloader, i think every rom that you flash through odin has one, but i guess it may not, its best to search this, but i have read a few posts that say you need to click on update bootloader (i would check into this, as if this is wrong it will definitely brick your device)
My suggestion is go back to the onclick odin thing as that should do it, im sure someone has done something similar.
Yh so to sum up, i would have high hopes for a restoration (but what so i know ) and yes flashing a new bootloader with rom i reckon would do the trick. I think a stock rom will do it. Click on the stock rom link below and type in a few search terms in that thread to see if you pick up anything otherwise do a slightly wider one of the forum.
Talon26 said:
So you haven't tried the jig yet?? because you haven't got it yet right
I don't think the device is bricked at all. Bricked usually means you have no response from it, so no matter what combo, actions you take you get no reaction.. However you are getting a boot although there is something going wrong as it does so...
So yes you need a new bootloader, i think every rom that you flash through odin has one, but i guess it may not, its best to search this, but i have read a few posts that say you need to click on update bootloader (i would check into this, as if this is wrong it will definitely brick your device)
My suggestion is go back to the onclick odin thing as that should do it, im sure someone has done something similar.
Yh so to sum up, i would have high hopes for a restoration (but what so i know ) and yes flashing a new bootloader with rom i reckon would do the trick. I think a stock rom will do it. Click on the stock rom link below and type in a few search terms in that thread to see if you pick up anything otherwise do a slightly wider one of the forum.
Click to expand...
Click to collapse
jig arrived today! .... i plugged it in ..... NOTHING ..... (read on theres more to the story!!!)
so i put it in nothing happened...... i thought maybe the jig device was not working so i tried it in the i9100 (s2) .... WORKED ...!
im really stubborn so i needed to make mine work too..... i read in a review of the jig device that someone bought one and it hadnt worked .... i hadnt ruled that out
anyway all day i just kept trying to jump start it by putting in the wall charger in and out ... i usually get some reponse from that....nothing apart from a second of something like a loading circle......
anyway then i left it on charge for an hour ....maybe the battery was dead and then tried again ....
(btw i was getting no response at all at this stage, not even the at&t thing ...)
so it was pure black screening me.....
then i got home from work and thought let me exchange the battery and see what happens....
i changed the battery and put the jig device in ...... VOILA !!! download mode....
all is well so far i've flashed with 2.3.3 pda,phone and csc files and checked repartition... i haven't messed with the bootloader option
seems to be working ok....also gave it a restart too ... last time it got to this point but it didnt turn back on after a restart ....
in conclusion .... charge battery fully externally (putting the power in the phone in this state was not charging it)
then with a full battery put jig in .... if that doesnt work you phone might be seriously bricked.... bravo to whoever dreamt up the jig device
Glad to hear the great news!
Nice
Thanks for this useful info
I hope someone can help me here, I'm posting with the belief that this may be a simple enough problem (With the hope).
I tried to install a Custom Recovery on my Galaxy S using this tutorial - wiki.cyanogenmod.org/w/Install_CM_for_galaxysmtd
I managed to get to step 6, and a blue bar appeared, but then i could not do step 7.
Now i cannot boot into recovery mode, nor will the phone boot past the Samsung Galaxy S logo.
I can still get into download mode, but Odin does not detect the phone.
. I have changed cable and tried different versions of Odin..
When i turn on the phone normally it shows the Samsung Galaxy S logo, blinks, and then reboots and does the same.
When i try to enter recovery, i get the same, unless i connect it to the PC. I then get an 8 pointed star, like the loading flash circle thing - the same as a flash video loading except it does not move.
I have also removed the battery and tried to enter recovery and download mode while inserting the battery.
I have removed the SIM and battery for a few minutes.
when i try to start Zadig, with the phone connected in Download mode, i get "Gadget Serial" as the device connected. I used to get "Samsung USB Composite Device"
I have tried many different things and read over the recommended threads on this forum. I think i need a bit more pointing in the right direction.
I really hope somebody can help me. I am very worried that i may have bricked it.
Thank you.
Try this:
This feature is great for people who
a) Have a bad KIES flash
b) Stuff up their phone somehow
c) Accidentally flash something dodgy via ODIN
d) Some other random occurence
To test this feature you just need to start with your phone turned off... Best way to be sure is to remove the battery.
Then
1. Put battery back in
2. Press and hold Volume Up + Home Key
3. Continue holding those buttons and then press and hold power button.
4. When you see the logo pop up release power button ONLY
5. Keep holding two buttons from step 2 until you enter recovery mode.
I hope this helps?
Also have you tried everything on this thread:
http://forum.xda-developers.com/showthread.php?t=1134975
akash6969 said:
Try this:
This feature is great for people who
a) Have a bad KIES flash
b) Stuff up their phone somehow
c) Accidentally flash something dodgy via ODIN
d) Some other random occurence
To test this feature you just need to start with your phone turned off... Best way to be sure is to remove the battery.
Then
1. Put battery back in
2. Press and hold Volume Up + Home Key
3. Continue holding those buttons and then press and hold power button.
4. When you see the logo pop up release power button ONLY
5. Keep holding two buttons from step 2 until you enter recovery mode.
I hope this helps?
Also have you tried everything on this thread:
http://forum.xda-developers.com/showthread.php?t=1134975
Click to expand...
Click to collapse
I hadn't seen that thread, but i have gone over tons of them Thanks for reply.
I eventually got Odin to detect it and I tried this - http://forum.xda-developers.com/showthread.php?t=1544487
It came up red and said failed.
I closed odin and disconnected the phone. Now i can't even turn it on.. Nothing. I am hoping the battery died, and it's a coincidence..
No response at all to any buttons... I haven't done anything else.
If i can get it to power up again, i'll try those tips.
Tomato_Jam said:
I hadn't seen that thread, but i have gone over tons of them Thanks for reply.
I eventually got Odin to detect it and I tried this - http://forum.xda-developers.com/showthread.php?t=1544487
It came up red and said failed.
I closed odin and disconnected the phone. Now i can't even turn it on.. Nothing. I am hoping the battery died, and it's a coincidence..
No response at all to any buttons... I haven't done anything else.
If i can get it to power up again, i'll try those tips.
Click to expand...
Click to collapse
Ok, Don't worry, Charge your phone battery to 100%, leave over night. ( keep charger connected to your phone overnight)
Best to have a fully charged battery in these situations!
Keep calm, and read and prepare what you want to do next.. Don't try everything in a frantic effort to get your phone started again.
I know it's difficult, but there are lots of threads on how to rectify most problems.
I wish you Good luck!!
sorry to ask some stupid question, but can u make sure what versiom ur fone is?
is it i9000?, or i9001 or i9003? or korean anycall? as far as i know, flashing i9000 ROM to i9003 will hardbrick da device.
Sent from my GT-I9000 using xda premium
akash6969 said:
Ok, Don't worry, Charge your phone battery to 100%, leave over night. ( keep charger connected to your phone overnight)
Best to have a fully charged battery in these situations!
Keep calm, and read and prepare what you want to do next.. Don't try everything in a frantic effort to get your phone started again.
I know it's difficult, but there are lots of threads on how to rectify most problems.
I wish you Good luck!!
Click to expand...
Click to collapse
Thanks.
This is a disaster. I tried to power it on to any mode there before i saw your post.
I needed to update the phone, because an app i needed for studying was only available on Android 4+.
Now no phone..
I saw a few threads, i hope after i leave it overnight i'll be able to power it.
If not, probably a JIG?
I don't fancy making one, but if i have to, i guess i'll give it a try. I don't think i could wait a week or more for a premade one to be delivered.
Anyway, for now, i'll keep my fingers crossed.
Thanks for help/tips and reply.
I'll post back tomorrow, hopefully with some better news.
Tomato_Jam said:
Thanks.
This is a disaster. I tried to power it on to any mode there before i saw your post.
I needed to update the phone, because an app i needed for studying was only available on Android 4+.
Now no phone..
I saw a few threads, i hope after i leave it overnight i'll be able to power it.
If not, probably a JIG?
I don't fancy making one, but if i have to, i guess i'll give it a try. I don't think i could wait a week or more for a premade one to be delivered.
Anyway, for now, i'll keep my fingers crossed.
Thanks for help/tips and reply.
I'll post back tomorrow, hopefully with some better news.
Click to expand...
Click to collapse
Sorry to say, most likely you will need a USB JIg to fix the problem you have. :/
If you linked the correct page when you said you tried to do this- and if I opened the correct page, that takes you to an SII section. Those are SII firmwares, not for the S.
So as compacity said, please clarify what device you have... Whether its an I9000 (galaxysmtd is for the I9000) or an I9100 (the firmware page you linked). If you do have an I9000, then your brick comes from flashing a different device's rom onto the S, which would give this error in Odin beause its incompatible.
In this case, you'd probably need a USB Jig to come out of it.
Try what the others said and hopefully you'll be at least able to enter Download mode before resorting to a jig, but considering your situation, I have to say realistically a jig is your best bet :/
Sent from my GT-P7510 using Tapatalk HD
You need a usb jig. It will get you into download mode. Now you need to flash cf root, which will come with cwm recovery. Recovery mode should work now. If you get computer!phone, then re-flash cf root. Now you should be able to flash CyanogenMod via cwm recovery. Thank if I helped!
Sent from my GT-I9000 using cm10.1
Soryuu said:
Sorry to say, most likely you will need a USB JIg to fix the problem you have. :/
If you linked the correct page when you said you tried to do this- and if I opened the correct page, that takes you to an SII section. Those are SII firmwares, not for the S.
So as compacity said, please clarify what device you have... Whether its an I9000 (galaxysmtd is for the I9000) or an I9100 (the firmware page you linked). If you do have an I9000, then your brick comes from flashing a different device's rom onto the S, which would give this error in Odin beause its incompatible.
In this case, you'd probably need a USB Jig to come out of it.
Try what the others said and hopefully you'll be at least able to enter Download mode before resorting to a jig, but considering your situation, I have to say realistically a jig is your best bet :/
Sent from my GT-P7510 using Tapatalk HD
Click to expand...
Click to collapse
huskyT said:
You need a usb jig. It will get you into download mode. Now you need to flash cf root, which will come with cwm recovery. Recovery mode should work now. If you get computer!phone, then re-flash cf root. Now you should be able to flash CyanogenMod via cwm recovery. Thank if I helped!
Sent from my GT-I9000 using cm10.1
Click to expand...
Click to collapse
Both helped a lot, thanks.
I had to end up bringing the phone to a repair shop
Something i am not inclined to do if i can avoid it. Especially if i caused it, i would hope i could undo it. But because i need a jig, and i wouldn't have time to get one or make one before Monday, i had to bring it to someone else.
I am buying the materials for a jig, and maybe going to buy one also, for future.
@Soryuu - Yep, i linked to the page, so i must have flashed the wrong firmware.
I'm angry with myself because i read everything else carefully. I had been reading all day. I guess i was just tired and thought I had got to the final hurdle. I was careless.
@huskyT - Thanks, will know that for future reference. I have two old Android phones somewhere. One is a Galaxy Europa, and one is an LG (not sure what model). Both are borked in some way, but i could probably use them for practice. I think the Galaxy Europa is flashed badly. Not by me. (Thankfully).
Tomato_Jam said:
Both helped a lot, thanks.
I had to end up bringing the phone to a repair shop
Something i am not inclined to do if i can avoid it. Especially if i caused it, i would hope i could undo it. But because i need a jig, and i wouldn't have time to get one or make one before Monday, i had to bring it to someone else.
I am buying the materials for a jig, and maybe going to buy one also, for future.
@Soryuu - Yep, i linked to the page, so i must have flashed the wrong firmware.
I'm angry with myself because i read everything else carefully. I had been reading all day. I guess i was just tired and thought I had got to the final hurdle. I was careless.
@huskyT - Thanks, will know that for future reference. I have two old Android phones somewhere. One is a Galaxy Europa, and one is an LG (not sure what model). Both are borked in some way, but i could probably use them for practice. I think the Galaxy Europa is flashed badly. Not by me. (Thankfully).
Click to expand...
Click to collapse
Don't stress mate, we all have bad days, we all make mistakes
Sent from my GT-P7510 using Tapatalk HD
Well....
I would have been quicker if i had ordered a jig and done it myself.. (Worth mentioning, i had told guy in phone shop what happened, and about the required "jig")
I collected my phone from the shop today, after a week, and i was told "Your phone is f*****d". To which i replied, "what? are you sure, i mean, i have only flashed it with SGS2 firmware, i'm under the impression it is very hard to break/brick, if i have a jig."
He told me, "Nope, it's beyond repair, it won't work. If you want, i can use the screen and other parts, i'll buy it off you for €40"
No thanks.
So now i am on the lookout for a premade jig. Does anybody know where i can buy one?
I meant to last week, but things happened, and without a phone i was running around a bit...
I'm going to check ebay, but if somebody could recommend somebody reliable, i'd prefer that. Thanks.
I bought it from ebay, no problem...but just saw a couple of minutes ago that also on amazon germany these jigs are offered now/in the meantime....
rodman01 said:
I bought it from ebay, no problem...but just saw a couple of minutes ago that also on amazon germany these jigs are offered now/in the meantime....
Click to expand...
Click to collapse
Thanks.
I bought a jig, and it arrived today. Have phone in charger.
Do i just plug the jig in?
Or do i also do the three button press?
The screen is completely black, and nothing appears on it.
only plug the jig in, thats all... phone will start in download mode of its own. :fingers-crossed: :fingers-crossed:
rodman01 said:
only plug the jig in, thats all... phone will start in download mode of its own. :fingers-crossed: :fingers-crossed:
Click to expand...
Click to collapse
Thanks, going to leave it charging for a little longer, and try it.
If it doesn't work, would a motherboard for the Samsung Galaxy S be easy to replace? I have found one unlocked for €25.
EDIT
Found a tear down video here - http://www.youtube.com/watch?v=vxPWsLd05F4
yes thats not so difficult...only thing a bit complicated is to open the back or middle cover...but there are a few movies on youtupe where you can see how it can be opened and dismounted....btw for the first try with the jig battery has not to be that full...only if it starts in download mode and you can flash it via odin I would recommend to charge it complete.
rodman01 said:
yes thats not so difficult...only thing a bit complicated is to open the back or middle cover...but there are a few movies on youtupe where you can see how it can be opened and dismounted....btw for the first try with the jig battery has not to be that full...only if it starts in download mode and you can flash it via odin I would recommend to charge it complete.
Click to expand...
Click to collapse
Thanks again.
I am after removing it from the charger, and inserted the jig. It's in about 30 seconds now, and nothing is happening..
that sounds not good...ususaly it takes only a few seconds or perhaps a minute till it starts to download mode....sorry for no better news....
rodman01 said:
that sounds not good...ususaly it takes only a few seconds or perhaps a minute till it starts to download mode....sorry for no better news....
Click to expand...
Click to collapse
What seems to have happened, is i tried to flash it with SGS2 rom. So is it unbrickable?
I am not sure but I think that minimum the bootloader is damaged...there is one more possibility: to repair it via jtag...but for this you have to find someone, who ones one and can repair it....some of the guys don't take much money for such a repair, but with transport costs ets...perhaps it would be cheaper and faster if you take the new mainboard you mentioned.