hi gang.
I have a bone stock gn 7000 in the US on ATT.
my kernel and build is XXLA6.. baseband is XXLA4
I plan on using PC Odin to flash the German ICS.
I've already installed Kies and PC Odin recognizes my device.
I have been told to do a 'nandriod back up' first..
And been told That I need CWM first to do this nandriod backup.
Can anyone tell me "how to" get CWM on my phone?
where to get the software and how to install it.
And finally how to do the back up.
I'm green as grass and have never flashed before anything
thanks for all your help.
all replies are.welcomed and encouraged.
thanks again.
Follow this guide : http://forum.xda-developers.com/showthread.php?t=1329360 ....... and see also here : http://forum.xda-developers.com/showthread.php?t=1406137
thank you, david
I've been all over your first link a few times before.
I've seen no clear and direct link to CWM and intructions to CWM only... without root.
I don't believe that I need root or do I?
I just need to to a nandroid back up.
I believe that my rom XXLA6 is non rootable anyways..
I only need CWM only and cannot find the software and instructions.
and your other link covers the 9 inch tablet...
thanks again
A NANDROID is a master backup tool which is available through the CWM Recovery's "backup and restore" menu. It stores everything in the ROM except the kernel. It's more like this analogy: a photograph which captured the exact state of your ROM, apps and all at the moment of backup. It is recommended in case of emergency and in case you need to go back to the latest working ROM. How-To section below.
You need CWM Recovery for this one. Once you're in CWM Recovery, the process is straightforward. Look for the "backup and restore" menu, access it and you will see two options: "backup" and "restore". Select "backup" and wait until the system gathers all data and packs it as a backup located in your internal memory, inside a folder called "clockworkmod".
For restoring the process is the same. You need to do the following to ensure a proper restore and prevent issues that might pop up: Wipe your system using CWM Recovery's "wipe data/factory reset" and after that go to "advanced" and now "wipe dalvik cache". Now go to the "mounts and storage" menu and select "format /system". That was a full wipe. Now proceed to the "backup and restore" menu, select "restore" to select your backup. Remember to reflash the kernel if you had one that didn't come with the ROM (like _motley's for example). The linck of tablet is used to know what are the permissions of root end CWM recovery...
Again, David thanks for your response. You seem to be the only one willing to help..
I do believe that you are missing my point..
"I need CWM ONLY". I need the software and instructions to install CWM only.
Your links and your instructions do tell me what to do once CWM is installed..
BUT.. HOW TO get CWM in the first place??
Once CWM is on my phone.. then yes.. I can use your instructions.
BUT FIRST... I need to install CWM on the phone..
Can you tell me HOW TO get and install CWM..
We have to start at the beginning..
Where to get CWM ONLY... How to install it (CWM)?
Ive given thanks again.. please help with the first steps in this process..
I dont want to brick just trying to
INSTALL CWM
only then I can use your instructions on what to do with it..
FIRST I need CWM....
HOW to get CWM on the phone is the question.
thanks alot
hmm, maybe this thread?
[02Feb12]How to Root/Unroot Samsung Galaxy Note + CWM (simple step at end of post)
1. Get permission from Root of Gnote : no other way to get root on the notes, but the most rapid and painless way is to follow There are several ways to get the root notes, but the most rapid and painless method is to follow the method Zergrush Zergrush. Download here :. http://forum.xda-developers.com/attachment.php?attachmentid=841876&d=1325678726 Before proceeding, check to settings -> info on the proceeding, controlled settings -> info on the device -> build version of your firmware version: the device -> build version of your firmware version: the Zergrush not Zergrush not work from KL7 firmware on, but work on the firmware KL7 work on, but work on those below the KL3 included (including those below the KL3 ( here http://forum.xda-developers.com/showpost.php?p=20963707&postcount=1 list of firmware directly rootable). If a list of fimrware directly rootable). If so then you have such a such a firmware KKA go ahead, if you have such a KL7 not work; firmware KKA go ahead, if you have such a KL7 not work; premuratevi also marked by premuratevi also to mark somewhere in the firmware somewhere the firmware originally installed CSC and especially for the latter was originally assembled and inserted above the CSC for the latter enter the code from the keypad by keypad code
* 2767 * 4387264636 # * 2767 * 4387264636 #
and note the last three characters (eg ITV, XEU etc.), and note the last three characters (eg ITV, XEU etc.), will serve you if you should bring your notes to his condition will serve you if you should bring your Notes to its original condition...... Now, if you have a firmware directly rootabile and you have at this point, if you have a firmware directly rootabile and you've followed the guide linked transactions, your Gnote has obtained the operations of the guide linked below, your Gnote has obtained permission the root, skip the next section of the guide. If you do not have root, skip the next section of the guide. But if you can not use the zergrush, you can downgrade to use the zergrush, you will need to downgrade to a firmware rootabile; ....... 1.1 Flash via Odin: Downgrade a firmware rootabile 1.1 Flash with Odin: Downgrade a firmware rootable ........ Then download a firmware rootabile, choose from a list of "Directly rootable" then download this firmware rootabile, choose from a list of "Directly rootable" from this : http://forum.xda-developers.com/showpost.php?p=20963707&postcount=1 ....download odin 1.85 here : http://forum.xda-developers.com/attachment.php?attachmentid=815370&stc=1&d=1323799721 ..... guide odin here : http://forum.xda-developers.com/showthread.php?t=1424997 ..... 2. CF-ROOT: root+CWM recovery 2. CF-ROOT: root+CWM recovery : ... Here simplified Rooting and CWM recovery for Galaxy Note N7000 - Download Root package, see at end of post - There are three folder 1. Initial CFroot flasher 2. Two other folder having zImage file , you need one only
Which file do I use ? Listen closely, for I will say zis only once! Go to Settings -> About phone -> Kernel Version. Note the string present there: 2.6.35.7-N7000XXKJ4-CL641703 What matters most (KJ4) in this case, is in bold. Try to find the matching file e.g. CF-Root-SGN_XX_XEN_KJ4-v5.0-CWM4.zip)
so choose accordingly
- Place the zImage file accordingly in folder 1.initial CFroot flasher /zImage folder
- Start "already-rooted.bat" and follow the instructions If you are Rooted already OR - Start "not-rooted-yet.bat" and follow the instructions.
Note : Just below this, where you download actual flash programme, that includes initial CF root as well i have already placed zimage accordingly. .....guide here : http://forum.xda-developers.com/showthread.php?t=1329360 _
lots and lots of replies telling me where to find root and cwm...
I ONLY want CWM.. that's all NO ROOT..
CWM only.......
or.. Do I have to root before I get CWM on my Phone.
Do I need root in order to install and use CWM??
If so.. then thanks to yous for pointing me to all that stuff..
IF NOT.....
then I only need CWM.. that;s all,,,, NO root!
If you can help with me installing CWM ONLY, then cool.. thanks alot!
http://forum.xda-developers.com/attachment.php?attachmentid=1056408&d=1336826886
Flash this from Samsung recovery (Volume up + power + home). This is an extremely unstable kernel. DO NOT WIPE ANYTHING from this kernel. ONLY use this version of CWM to install a safe GB or ICS kernel first. After this, you are free to flash anything you'd like.
The simplest way to get CWM and start flashing ROMS.
Flash this kernel is stable whit recovery read here : http://forum.xda-developers.com/showthread.php?t=1443385 .... let me know...!
Related
Here are the details of my tab
Firmware Version: 2.2
Baseband Ver: I987UCJK1
Kernel Ver: 2.6.32.9 [email protected] #1
Build Number: FROYO.UCJK1
Carrier: At&t US
So I managed to root my device using Superoneclick but I'm having trouble running clockworkmod because of a package verification error. I've realized that I need to upgrade my kernel to make it work. But I'm having trouble finding the right kernel/rom. I'd prefer to flash a new rom using ODIN but I'm unable to figure out which rom to use. Can anyone suggest me a rom to choose? I'm confused by jk,jv,ja terminology
Flash the rotohammer JME version 4. Then flash chainfire cf root to get CWM. BE SURE TO USE FROYO VERSIONS NOT THE GINGERBREAD VERSION.
I believe AT&T is a GSM tab, uses a sim card, so any GSM roms will work. If its doesn't use a sim card look for the CDMA roms.
I would suggest upgrading to gingerbread as that works really well.
The best advice I could give is read any guides on updating REALLY well, go slow, doublecheck what you've done and DON'T skip steps because you read through already.
If you want to keep all your Contacts, Apps ETC... then backup with Titanium Backup before you flash as this will clear it out...
GSM ROM
Go here - http://forum.xda-developers.com/showthread.php?t=888071 it will give you an app thay allows you to check your bootloader.
You may have to go to settings>Applications>unknown sources needs a tick to install.. This allows the installation of 3rd party apps using file manager. Run the app, it will tell you if the bootloaders are locked or ask if you want to unlock... Use at your own risk...
So saying, this was the first gingerbread rom I flashed - http://forum.xda-developers.com/showthread.php?t=1073854
Instructions were - Procedure (ODIN !):
- Download and extract the firmware zip
- Download and extract the attached gt-p1000_mr_PIT.zip
- Download and extract the attached dbdata.zip
- Flash the firmware tar as PDA, repartition enabled, use the attached PIT
- After flash immediately boot into download mode again - wait for it to go to the samsung LOGO here as a whole heap of writing goes up the screen then it reboots. DO NOT TURN OFF UNTIL IT REBOOTS TO THE SAMSUNG LOGO...
- Flash dbdata.tar as PDA (NO repartition) in ODIN again.
- After flash immediately boot into recovery mode
- Wipe cache
- Wipe data / factory reset
- Wipe Dalvick cache
Then flash this in ODIN - http://forum.xda-developers.com/attachment.php?attachmentid=593112&d=1305133135
This will root your device.
I then updated to this - http://forum.xda-developers.com/showthread.php?t=1074759
Cheers...
Added this set of instructions, it has pictures, remember there will be some differences... - http://forum.xda-developers.com/attachment.php?attachmentid=596770&d=1305467639
Before you flash anything, kindly check if you have protected/locked/signed bootloaders.
Thanks for the quick replies guys. Do appreciate it. So regarding the bootloaders, what should I milk for?signed, secured??
Just a comment about the procedure above.....unless you have CWM you will not see an option for dalvick cache in the default recovery,at least for mine the last entry was for cache-no advanced features like battery wipe and dalvick......
Hello,
I am completely new to flashing roms on android devices and i am just trying to understand the basics behind the process.
- Installing custom roms
- reverting back to stock firmware after installing a rom
I read the 4th post in this thread : http://forum.xda-developers.com/showthread.php?t=991792
i kinda have some understanding about flashing roms now but i still dont fully understand it.
My device is a Samsung Galaxy S i9000.
Thanks
What exactly do you want to know?
1. Installing custom roms is pretty easy the hard part is choosing the rom and to flash a rom you need to have the cwm recovery and like be on the base you need. ex: lets say you are on a jvt rom and you want to flash a jw1 rom, well in this case you dud need to flash jw1 from odin and then flash the rom from recovery...., but if you are on a jw1 custom rom, then in that case you can just flash the rom from recovery with wipe (recommended).
2. To flash back to stock: you dud need the stock file from sammobile or from wherever you get it and you would need odin, you place your phone in download mode then you put 512pit in the pit section/ code in the pda section/ modem in the phone section/ and csc in csc. then you have to make sure that repartition is ticked and all the others. make sure that the download is not interrupted for that would brick the phone.
-to flash a kernel you dud need to put the tar file in pda and Don't check repartition and click start.
I hope this helped a little
and remember to do this at your own risk.
Sorry for the noob questions but im just trying to understand haha
1. what are jvt and jw1 roms?
2. When you say be on the base you need do you mean the base firmware required for the rom?
3. How would i know which rom i have now, JVT or Jw1?
4. Whats the thing u mentioned whipe in "you can just flash the rom from recovery with wipe (recommended).?
last.5. I already found the stock firmware i have now and ive downloaded it for later if i need to restore it. but what is the tar file you mentioned in the end?
Thanks Man. I appreciate it.
yazzy44 said:
Sorry for the noob questions but im just trying to understand haha
1. what are jvt and jw1 roms?
2. When you say be on the base you need do you mean the base firmware required for the rom?
3. How would i know which rom i have now, JVT or Jw1?
4. Whats the thing u mentioned whipe in "you can just flash the rom from recovery with wipe (recommended).?
last.5. I already found the stock firmware i have now and ive downloaded it for later if i need to restore it. but what is the tar file you mentioned in the end?
Thanks Man. I appreciate it.
Click to expand...
Click to collapse
sorry, this is not meant to be offensive but you have a lot to read. There're some good tutorials on how to flash your phone here on xda. search for it.
short answers to your questions:
1. jvt or jw1 are versions of stock samsung roms
2. I think he means if you are on a jvt rom you should only flash custom roms for jvt
3. settings>about phone
4. wipe means resetting the phone, deleting cache and dalvik-cache
no matter what u know u first should know about flashing stock roms..in case u mess something up u will need to flash the stock roms,its a good thing that u have already downloaded these..then u should know how to install kernels to root n have Clockworkmod recovery,then u will be able to flash custom roms..u should serach the net for these questions with a 'How to' at first...
Instruction for new ROM installation
There are basically 2 methods for flashing a ROM
1. CWM recovery menu mode
2. Download mode.
1. For CWM recovery mode you phone must be rooted with CWM, just put the ROM zip file in sdcard of your phone of your choice. then power off the phone. Then you may want to boot in reovery mode for this use pressing and holding 3 button combination simultaneaously as Volume UP + Home key + Power key now you should be booted in to recovery mode there just wipe data/factory reset then wipe cache from option then find and select install from sdcard -> chose file zip from sdcard and press power key to selct and start flashing. wait max 5 min and your phone will be booted with new rom of your choice.
2. Boot in to download mode by pressing and holding 3 button combination simultaneaously as Volume down + Home key + Power key now you should be booted in to download mode now connect your phone with PC and open odin in PC then select ROM file as PDA, PHONE & CSC under propoer boxes then click start - wait max 5 min and you phone will be booted in to new rom.
Thanks
dktechdev.in
Enjoy...
1st - Rooting - visit http://gopalasubramanium.blogspot.in/
2nd - Custom ROMs List - http://alchemistar.blogspot.in/2010/10/samsung-galaxy-s-custom-roms-list-1014.html
3rd - Original ROMs List - http://forum.xda-developers.com/showthread.php?t=1102881
I tried to find out how to root my GN, GT-N7000B.
But I could not find out the way.
Even I checked Kernel Version, LA2 there is no way to root.
Finally, I think my phone is a kinds of Not Directly ROM.
So, I will downgrade my ROM.
Before that, I would like ask if there is anyone who succeed to root this model.
Thanks in advance.
rapboy75 said:
I tried to find out how to root my GN, GT-N7000B.
But I could not find out the way.
Even I checked Kernel Version, LA2 there is no way to root.
Finally, I think my phone is a kinds of Not Directly ROM.
So, I will downgrade my ROM.
Before that, I would like ask if there is anyone who succeed to root this model.
Thanks in advance.
Click to expand...
Click to collapse
Check the information on this website:
http://rootgalaxynote.com/galaxy-note-root/how-to-root-galaxy-note-gt-n7000-method-2odinheimdall/
Upgraded GT-N7000B
rapboy75 said:
I tried to find out how to root my GN, GT-N7000B.
But I could not find out the way.
Even I checked Kernel Version, LA2 there is no way to root.
Finally, I think my phone is a kinds of Not Directly ROM.
So, I will downgrade my ROM.
Before that, I would like ask if there is anyone who succeed to root this model.
Thanks in advance.
Click to expand...
Click to collapse
I decide to root my phone accroding to Dr. Ketan.
I thought this phone is non directable ROM.
Check this as the below.
---------------------------------------------------------------------------------------------------------------
When No Any other method works to Root your device, use this
---------------------------------------------------------------------------------------------------------------
Note that, this will downgrade your ROM to KJ1, after that you can update it.
Download: https://rapidshare.com/files/3690281..._FACTORYFS.zip
(special thanx to schiwa for providing premium a/c to host file)
- Make sure your SGN is NOT connected to your computer
- Reboot your SGN into "download mode" (Vol Down + Home + Power)
- Start ODIN
- Click the PDA button, and select the "SGN_XX_OXA_KJ1_FACTORYFS.tar" file
- Connect the SGN to your computer
- Make sure "repartition" is NOT checked
- Click the START button
- Wait for the phone to reboot TWICE
- Done.
Now you have your device Rooted, Install Mobile Odin Pro n update your device to any new ROM with Mobile Odin
Click to expand...
Click to collapse
When I was done this instruction there are two bugs.
one is typing error "null, null" and the other is brick whenever turn off the display.
But I flashed Chrack's ICS XXLPY V4 directly.
Check this as the below.
##############################################
# Download small v4 (332MB): Chrack_XXLPY_small_xda_v4.zip
# MD5 Hash: 8DDC1C4DDEC2FAE19A6B838A15660888
##############################################
From the small Version i deleted some Apps.
The Apps can you download here:
Download lite Apps (301MB): lite apps xxlpy.zip
MD5 Hash: 4567FCD16B4BF80BBEC686BB14B4029D
Instruction
a) coming from a rooted GB-ROM:
- download Abyss Kernel 4.2 from here: http://www.mediafire.com/?c65mndvpk6ocbaa
- put zip-file on your USB-storage
- boot in Recovery
- Flash Abyss Kernel 4.2!!!
- boot back in recovery (you find this option under 'advanced')
- FullWipe
- Flash ROM
- reboot system
- ...you are done
==> there have been reported problems with a constantly rebooting system when doing installation coming from a GB-ROM as posted above! So the safe and 100% successful way is installing LPY Stock-ROM, root Stock ROM and then go on as described below under point b2). Do not ask for a tutorial on how to install and root LPY Stock ROM....it is describe enough here in Forum!
Click to expand...
Click to collapse
Now I am using my phone after installation of ICS.
There will be some bugs during installation.
But you can do it because I already succeed to root and flash ICS.
Good Luck!!
I have the gtn-7000 note. Its on 2.3.6. The kernal is LA6.
Ive read many guides but they are too confusing. Is i t possible if I can root my phone? If not, then what do I have to do? If it requires flashing etc then will it brick my phone?
Thank you.
TwilightLoz said:
I have the gtn-7000 note. Its on 2.3.6. The kernal is LA6.
Ive read many guides but they are too confusing. Is i t possible if I can root my phone? If not, then what do I have to do? If it requires flashing etc then will it brick my phone?
Thank you.
Click to expand...
Click to collapse
Go to dr ketan's thread there is a gb rom there that is already rooted when you flash it. The gb rom has no superbrick issue only ics if you factory reset or recovery data wipe or do a nandroid.
Here. http://forum.xda-developers.com/showthread.php?t=1816158
http://forum.xda-developers.com/showthread.php?t=1329360
On the third post, it tells me how to root but I am a bit confused.
Is Odin the same thing as CWM?
Will this brick/malfunction my note?
After rooting, would I have to download the LA6 kernal?
Can someone give me the link to PC Odin?
TwilightLoz said:
http://forum.xda-developers.com/showthread.php?t=1329360
On the third post, it tells me how to root but I am a bit confused.
Is Odin the same thing as CWM?
Will this brick/malfunction my note?
After rooting, would I have to download the LA6 kernal?
Can someone give me the link to PC Odin?
Click to expand...
Click to collapse
1. odin is not CWM
2. yes, there is always a chance to brick, no guarantees.
3. no
just follow this:
2. Long, No raised couter OR Exclamation mark
-Downgrade to Rootable GB ROM and Root it. OR Download This pre rooted GB ROM and flash using PC Odin
-Wipe cache, data and delvic cache from recovery
-Install Mobile Odin Pro
-Copy ICS ROM file in .tar (you want to flash) to Internal SD card (recommended, but you can have it on EXT too)
-Copy one of custom Kernel in .tar file e.g.Notecore, Speedmod, CF root kernel Or other any with same function.
-Open Mobile Odin Pro
-select open file
-Point to ROM file you have copied
-All fiels will popup and feel automatically
-select kernel and point to custom kernel file you have copied
Flash.
Done!
you need to read some more on how to use pc odin properly.
Hello everyone, I've just bought my N7000, I used to have a LG P500, then a Xperia Sola, and now my amazing GALAXY NOTE !!!!
I'm reading a lot getting the info needed to get into this device and I find particulary confusing the rooting stuff.
I have found this tutorial by dr.ketan
[24sept12]How to Root/Unroot Samsung Galaxy Note + CWM
BUT acording to this thread by dr.ketan this method is dangerous.... and he says:
Present option to root ICS ROM is
So present option for rooting is - You can select any of one.
1. Short, easy - requires to reset counter
-Download Odin (.tar) version of custom kernel like Notecore, Speedmod, CF root kernel Or other any with same function.
-Flash it using PC odin for PDA tab.
-You will get exclamation mark and raised counter, which can be reset with Triangle Away
2. Long, No raised couter OR Exclamation mark
-Downgrade to Rootable GB ROM and Root it. OR Download This pre rooted GB ROM and flash using PC Odin
-Wipe cache, data and delvic cache from recovery
-Install Mobile Odin Pro
-Copy ICS ROM file in .tar (you want to flash) to Internal SD card (recommended, but you can have it on EXT too)
-Copy one of custom Kernel in .tar file e.g.Notecore, Speedmod, CF root kernel Or other any with same function.
-Open Mobile Odin Pro
-select open file
-Point to ROM file you have copied
-All fiels will popup and feel automatically
-select kernel and point to custom kernel file you have copied
Flash.
Done!
Click to expand...
Click to collapse
Those threads had 5 months old and my question is
¿What is the updated procedure to root the Note? (SAFE)
by the way I'm running Stock ROM 4.0.4 XXLRT
:good: Thanks
I would suggest u follow the 1.A method in dr.ketan's thread
It is the easiest and safest method to root your phone
I rooted by flashing a zip file.I think there is a site named galaxynoteroot or rootgalaxynote
Anyway,try to find the site.it has video tutorials too
Sent from my GT-N7000 using xda premium
as RAj says just flash the Philz kernel for the rom build from stock recovery and you will get rooted after a reboot
What about this option? is it safe?
http://forum.xda-developers.com/showpost.php?p=35512626&postcount=1
DUDE
go to Philz stock kernel thread. download the kernel that corresponds to your phone from this thread http://forum.xda-developers.com/showthread.php?t=1901191
reboot into recovery by doing the 3 finger salute.
flash it. and then reboot.
you are rooted and on a safe kernel.
simple
chenaou said:
What about this option? is it safe?
http://forum.xda-developers.com/showpost.php?p=35512626&postcount=1
Click to expand...
Click to collapse
that is safe too but it breaks the camera. so the philz kernel one is better