Please can you tell me how to install a new kernal through odin?
most kernels here have a CWM version which you can flash without odin, I recommend that!
There is also an app called "sgs kernel flasher" which allows you to flash a kernel right within the running phone!
If you want to use odin, chose pda and no repartion and no pit...
mimicuk said:
Please can you tell me how to install a new kernal through odin?
Click to expand...
Click to collapse
Have you used Odin before ?
1. Put phone in to download mode
2. do not connect phone to usb
3. start odin, select your kernel.tar in the pda selection
4. uncheck re-partition - check auto reboot
5. connect phone to usb - odin will diplay "added" in the txt scroll
6. press start
7. Odin will do it thing & if successful will display a "success 1/failed 0" line in the txt scroll
8. phone will reboot & your good to go.
Remember you do this at your own risk
Thankyou very much
Could some one for benefit of Indian Tab Owners, write a step-by-step instructions or guide. Lot of information to digest for a new user including details of 1) rooting 2) installing recovery 3) flashing ... this information would be great useful for everyone.
My Tab details :
(Model: GT-P1000 | Code: INU | Version: P1000DDJK3/P1000ODDJJ1/P1000DDJJ1)
hey..even i have a galaxy tab indian version...just follow the guides that are avaliable here for rooting flashing etc...etc...and i had the same modem when i bought it but its since been upgraded to a newer version of the modem so i just updated the modem to the ...DXJM2 version..thought the asian modem would be better for me..if u want i'll post the modem.bin
Dare{D}evil said:
hey..even i have a galaxy tab indian version...just follow the guides that are avaliable here for rooting flashing etc...etc...and i had the same modem when i bought it but its since been upgraded to a newer version of the modem so i just updated the modem to the ...DXJM2 version..thought the asian modem would be better for me..if u want i'll post the modem.bin
Click to expand...
Click to collapse
Thank you for quick reply. I started compiling the files need to flashing. So far, I could do following. Please advice me whether I am on the right path or not.
1. Rooted my tab with Z4root. Now I got root permission.
2. Downloaded Odin3 v1.7.exe and s1_odin_20100803.pit for flashing
3. Downloaded Roto-JMI-Full-v2.zip and Roto-JMI-Upgrade-v2.zip
Now, using Odin PDA button, I want to flash Roto-JMI-Full-v2.zip ?
Few questions:
a) Is this correct way of flashing or I am missing something?
b) Does above flash install Recovery also ?
c) which files need for PHONE and CSC files ?
d) Which firmware best suitable for Indian Tab ?
Thank you in advance for clarifying above.
I really appreciated reply for my questions as it would allow me to move forward. I will ensure a good documentation at the end of the process for benefit of other users.
nchary05 said:
Thank you for quick reply. I started compiling the files need to flashing. So far, I could do following. Please advice me whether I am on the right path or not.
1. Rooted my tab with Z4root. Now I got root permission.
2. Downloaded Odin3 v1.7.exe and s1_odin_20100803.pit for flashing
3. Downloaded Roto-JMI-Full-v2.zip and Roto-JMI-Upgrade-v2.zip
Now, using Odin PDA button, I want to flash Roto-JMI-Full-v2.zip ?
Few questions:
a) Is this correct way of flashing or I am missing something?
b) Does above flash install Recovery also ?
c) which files need for PHONE and CSC files ?
MId) Which firmware best suitable for Indian Tab ?
Thank you in advance for clarifying above.
Click to expand...
Click to collapse
Install Adfree or something which requires root acess for installation. Once rooted download something like root explorer from market which allows you to backup the modem.bin file. Or me or somebody else can just upload the file here.
Read the post/link in the thread where you downloaded Roto's JMI rom.
Use the .pit file from Roto's link not the thing which you posted...same place where you got the same ROM file. If you are flashing first time/from another rom then use the Full v2 zip file. Else use Update v2 when flashing from one of Roto's rom.
Connect the tab to your pc, reboot and go into download mode...press power+vol down button while rebooting...a yellow triangle icon with an android digging will come up...to get out of download mode,just keep the power button pressed till it rebooted normally.
Once in download mode, open up Odin and check that the yellow com box option is on. Check repartition option to ensure everything is wiped and you have a fresh install from scratch.
For PIT select the pit file downloaded from roto's link
For PDA select the Full.tar file
For PHONE select the modem.bin file
For CSC leave it blank...
Once done, recheck and hit start.
PLEASE CHECK ROTO'S JMI V2 THREAD IN THE DEVELOPEMENT SECTION...it has a link to howto which is old but gives some idea of how to proceed...for pit, pda, phone follow as I suggested and things will go fine...
Sent from my GT-P1000 using XDA App
Thank you.. I will do the same let you know the status....
blackheart2925 said:
Install Adfree or something which requires root acess for installation. Once rooted download something like root explorer from market which allows you to backup the modem.bin file. Or me or somebody else can just upload the file here.
Read the post/link in the thread where you downloaded Roto's JMI rom.
Use the .pit file from Roto's link not the thing which you posted...same place where you got the same ROM file. If you are flashing first time/from another rom then use the Full v2 zip file. Else use Update v2 when flashing from one of Roto's rom.
Connect the tab to your pc, reboot and go into download mode...press power+vol down button while rebooting...a yellow triangle icon with an android digging will come up...to get out of download mode,just keep the power button pressed till it rebooted normally.
Once in download mode, open up Odin and check that the yellow com box option is on. Check repartition option to ensure everything is wiped and you have a fresh install from scratch.
For PIT select the pit file downloaded from roto's link
For PDA select the Full.tar file
For PHONE select the modem.bin file
For CSC leave it blank...
Once done, recheck and hit start.
PLEASE CHECK ROTO'S JMI V2 THREAD IN THE DEVELOPEMENT SECTION...it has a link to howto which is old but gives some idea of how to proceed...for pit, pda, phone follow as I suggested and things will go fine...
Sent from my GT-P1000 using XDA App
Click to expand...
Click to collapse
I followed the steps after flashing 'full' tar, it rebooted tab, started the normally. After that, I verified that, all applications , phone (GSM) and wifi working fine.
Now my question is do I really need to flash *second* tar file ? what is it for ?
^^No. It is only for people upgrading from previous versions! You are good to go!
Now, I want to install CWM recovery. Please some one can confirm below steps:
1. Make sure to have Samsung Kies installed, and your tab at least connected once, to be sure the drivers are correct.
2. Your Tab must be Rooted.
3. If you wish to do a backup, now is the time.
4. You will need an SD Card with enough free space for the filesystem conversion, and to put the Overcome ROM on before we start. (An empty 4gb should be plenty, as long as it is empty, or close too)
5. Download and Extract the following file to your computer: http://www.apksmash.com/corodius/galaxytab.zip (Contains "Odin3 v.1.7.exe" "Overcome_Kernel_v1.0")
Now, we will Install the Kernel and perform the EXT4 filesystem conversion.
1. Turn off your Galaxy Tab.
2. Turn your Galaxy Tab on into DOWNLOAD mode (Press Volume DOWN and Power On at the same time).
3. Open Odin3 v1.7.exe on your PC.
4. Connect your Galaxy Tab to your PC via the USB cable.
5. Make Sure the ID:COM box is highlighted yellow (meaning it sees your tab).
6. Click on the PDA button and select the Overcome_Kernel_v1.0.tar file you downloaded earlier (make sure PDA is ticked after selecting the file).
7. The only boxes ticked should be:
A. Auto Reboot
B. F. Reset Time
C. The PDA tickbox
8. Click start and wait for PASS! to show highlighted green on Odin.
9. Your Galaxy Tab will Reboot, and get stuck on the Samsung Boot Screen. This is fine.
10. Turn your Galaxy Tab off by holding the power button for about 5 seconds.
11. Turn your Galaxy Tab on into RECOVERY mode (Press Volume UP and Power On at the same time).
12. The Galaxy Tab will now perform the EXT4 conversion.
13. Sit tight, depending on how much data you have, this can take quite a long time.
14. Once finished, click reboot system now (by pressing the power button).
At this point, You have installed the Overcome Kernel with CWM included and converted the Filesystem to EXT4. It has been reported that many stock ROMs will boot and run fine now, however some may not, but it just depends on your ROM etc.
http://forum.xda-developers.com/showthread.php?p=11713685.
Would be there any problem ? or is there any easy way to install CWM Recovery.
I had bricked my tab while modding battery icon and it was not booting now. Now i want to flash with the custom rom available here. I am noob to flashing so just want to confirm the steps mentioned above applicable to the bricked tab. Can somebody guide me for bircked tab.
Please mentioned the good custom rom with Ext4 conversion at the time of install. I am using indian tab.
@OP:- Sorry for hijacking this thread but find some info here for my queries
Can you get into download mode? If yes then you should be able to flash...but I would suggest checking"I bricked my tab" threads in general or developement section...
Sent from my GT-P1000 using XDA App
nchary05 said:
Now, I want to install CWM recovery. Please some one can confirm below steps:
1. Make sure to have Samsung Kies installed, and your tab at least connected once, to be sure the drivers are correct.
2. Your Tab must be Rooted.
3. If you wish to do a backup, now is the time.
4. You will need an SD Card with enough free space for the filesystem conversion, and to put the Overcome ROM on before we start. (An empty 4gb should be plenty, as long as it is empty, or close too)
5. Download and Extract the following file to your computer: http://www.apksmash.com/corodius/galaxytab.zip (Contains "Odin3 v.1.7.exe" "Overcome_Kernel_v1.0")
Now, we will Install the Kernel and perform the EXT4 filesystem conversion.
1. Turn off your Galaxy Tab.
2. Turn your Galaxy Tab on into DOWNLOAD mode (Press Volume DOWN and Power On at the same time).
3. Open Odin3 v1.7.exe on your PC.
4. Connect your Galaxy Tab to your PC via the USB cable.
5. Make Sure the ID:COM box is highlighted yellow (meaning it sees your tab).
6. Click on the PDA button and select the Overcome_Kernel_v1.0.tar file you downloaded earlier (make sure PDA is ticked after selecting the file).
7. The only boxes ticked should be:
A. Auto Reboot
B. F. Reset Time
C. The PDA tickbox
8. Click start and wait for PASS! to show highlighted green on Odin.
9. Your Galaxy Tab will Reboot, and get stuck on the Samsung Boot Screen. This is fine.
10. Turn your Galaxy Tab off by holding the power button for about 5 seconds.
11. Turn your Galaxy Tab on into RECOVERY mode (Press Volume UP and Power On at the same time).
12. The Galaxy Tab will now perform the EXT4 conversion.
13. Sit tight, depending on how much data you have, this can take quite a long time.
14. Once finished, click reboot system now (by pressing the power button).
At this point, You have installed the Overcome Kernel with CWM included and converted the Filesystem to EXT4. It has been reported that many stock ROMs will boot and run fine now, however some may not, but it just depends on your ROM etc.
http://forum.xda-developers.com/showthread.php?p=11713685.
Would be there any problem ? or is there any easy way to install CWM Recovery.
Click to expand...
Click to collapse
I followed above steps and could able to install CWM RECOVER.
congrats dude
maddy_in65 said:
I had bricked my tab while modding battery icon and it was not booting now. Now i want to flash with the custom rom available here. I am noob to flashing so just want to confirm the steps mentioned above applicable to the bricked tab. Can somebody guide me for bircked tab.
Please mentioned the good custom rom with Ext4 conversion at the time of install. I am using indian tab.
@OP:- Sorry for hijacking this thread but find some info here for my queries
Click to expand...
Click to collapse
can you just tel me which modem.bin are u using coz i was planning to flash but stuck on decision bcoz of modem... is it jpz or jk3? or any other
A new GB version is available DDJPA
http://forum.xda-developers.com/showthread.php?t=1226674
need PDA PIT PHONE CSC files
Kindly send me the links for downloading the PDA PIT PHONE CSC files as I could find only broken links.
My samsung tab (Version: P1000DDJK3/P1000ODDJJ1/P1000DDJJ1)) is bricked and won't boot.
Than You
nchary05 said:
Could some one for benefit of Indian Tab Owners, write a step-by-step instructions or guide. Lot of information to digest for a new user including details of 1) rooting 2) installing recovery 3) flashing ... this information would be great useful for everyone.
My Tab details :
(Model: GT-P1000 | Code: INU | Version: P1000DDJK3/P1000ODDJJ1/P1000DDJJ1)
Click to expand...
Click to collapse
Hello,
It is the first time when trying to change ROM on my galaxy s. Before I start I want to be sure I take the right steps.
First of all some info about my phone:
PDA version is I9000BUJS3
PHONE: I9000BUJS1
CSC: I9000GATLJS2
I downloaded the ROM via Check Fus Downloader from samsung:
CSC: I9000GATLJP5
Phone: I9000BUJP5
PDA: I9000BUJP7
All I need to do now is to run odin and select the .tar file in the PDA field, correct?
Code:
Procedure:
1.Open ODIN. (And close Kies, if you have it open. It is important to have ODIN open BEFORE connection the phone via USB!)
2.Select the PDA/Modem/CSC/.PIT files in Odin. (For kernel flashes, only PDA is required. For FW flashes, .PIT and at least a PDA is required. Some PDAs have Modem and CSC integrated. Make sure you have the correct .PIT file. Usually 512.pit)
3.Check the "Re-Partition" checkbox. (Only do this if you have separate packages for PDA, Modem and CSC! Don't do this for single PDA flashes or kernel flashes!)
4.Turn the phone into the download mode by pressing and holding VolumeDown+Home+Power.
5.Connect your phone with your computer and wait until the drivers are installed.
6.When the drivers are installed, click Start.
7.The phone will be flashed and once it’s finished, it will boot up. (Do NOT disconnect the usb-cable, remove the battery or otherwise interrupt this process!)
8.You have successfully flashed your phone.
My phone was sim locked when I bought it ( now is unlocked, i suppose it will stay unlocked after upgrading).
Thank you!
Be carefull to flash firmware your phone need to be sim unlocked and network unlocked.Lot of people dont check this.See the post about it.
[email protected]
your phone will stay unlocked
and your instructions above are fine
should that fail - you may need a 2.3 rom with all 3 files instead of the 1 .tar file
azzledazzle said:
your phone will stay unlocked
and your instructions above are fine
should that fail - you may need a 2.3 rom with all 3 files instead of the 1 .tar file
Click to expand...
Click to collapse
How to know for sure? And if will fail it will leave my device in an unstable state?
And another question: Does the bootloader for 2.2.1 work with 2.3 ?
I think you actually need the stock FroYo bootloader to upgrade to 2.3? I may be incorrect, don't quote me. 2.3.3 has its own bootloader I believe.
Hi, I'm new to the Android community (and xda-developers), that's why I'm having trouble with rooting my Note.
What I have tried:
- Download Odin 1.85
- Download pda.tar
- Start Odin, and add the pda.tar
- Connect the Note to the comp in Download mode.
- Click start
Odin fails doing that, and there are no error codes or something.
My details:
- Baseband N7000XXLA4
- Gingerbread 3.2.6
- Kernel 3.6.35.7-N7000XLLA6-CL907341
I hope you guys can help me out!
Rom You need to download a directly rootable stock rom try kk9 flash via Odin then use the root (kk9) from chain fires post then root
If you have a jig you could just flash the root via Odin or buy Odin mobile from market
hiddepolen said:
Hi, I'm new to the Android community (and xda-developers), that's why I'm having trouble with rooting my Note.
What I have tried:
- Download Odin 1.85
- Download pda.tar
- Start Odin, and add the pda.tar
- Connect the Note to the comp in Download mode.
- Click start
Odin fails doing that, and there are no error codes or something.
My details:
- Baseband N7000XXLA4
- Gingerbread 3.2.6
- Kernel 3.6.35.7-N7000XLLA6-CL907341
I hope you guys can help me out!
Click to expand...
Click to collapse
What I have tried:
- Download Odin 1.85
- Download pda.tar (Make sure you have the downloaded the correct rom)
- Start Odin, and add the pda.tar
- Connect the Note to the comp in Download mode.
- Click start (before starting check on the top has the COM port turned yellow in odin - if not then get the drivers installed or install kies- but stop kies running in background as it may interfere with odin)
Once com port turns yellow then click start.
Hope this helps!
Hit thanks if you can!
hi senior members
I have a SGS uk phone with the following details
Model GTI9000
Firmware 2.3.
Baseband version I9000NEJV5
Kernel vERSION 2.6.35.7 I9000NEJVD-CL183009 [email protected]
BUILD GINGERBREAD.NEJVD
I WANT TO ROOT THIS PHONE
WOULD APPRECIATE IF THE SENIOR MEMBERS CAN HELP ME WITH A STEP BY STEP INSTRUCTIONS ALONG WITH DOWLOAD LINKX OF ondin ETC WITH KERNEL LINKX FOR TAR FILES ETC.
MANY THANKX
j
35 views but no reply for help
Do you only want to root it or have a newer firmware on it (4.1.2?) as well? If I were you, I'd update
Sent from my Gameboy Color
BlueFlame4 said:
Do you only want to root it or have a newer firmware on it (4.1.2?) as well? If I were you, I'd update
Sent from my Gameboy Color
Click to expand...
Click to collapse
i want to root for i want to install copilot eu
i nstalled lucky patcher but it says phone not rooted
i dont have a sd card on the phone
can anybody help
U can upgrade to GB 2.3.6. Its an Open Europe stock rom
Get in download mode (3 button combo) & flash this JVU rom with odin with pit (use 512) & repartition ticked & the 2 next to it also
- Samsung USB drivers --> http://db.tt/BujOFVxz
- Odin & pits --> http://db.tt/yHvd2Brm
- JVU rom --> http://db.tt/z0WBjcFk
Here is an example:
PDA, select CODE_I9000XXJVS_CL565837_REV03_user_low_ship.tar
Phone, select MODEM_I9000XXJVS_REV_00_CL1059471.tar )
CSC, select GT-I9000-CSC-MULTI-OXAJVS.tar
PIT, select s1_odin_20100512.pit
Click start
When pass it reboots automaticly & install.
Done installing turn off Phone & Get in download mode again
Flash this cf root with odin in Pda section
- Cf root --> http://db.tt/BOrZ3cjN
After that it reboots and a cwm icon will appear. Click on it allow & your rooted
From there u can flash a custom rom of your choice or you can stay with gb.
so if its only phone then i shall only select the phone or shall select all
so if PHONE then i shall only select phone and then
Phone, select MODEM_I9000XXJVS_REV_00_CL1059471.tar )
or shall do all for the sgs
also please explain (3 button combo)
Select all files in odin before pressing start. Pit in pit, code in pda, modem in phone, csc in csc.
Turn your phone off & get your mobile phone in download mode pressing volume down + home button + power button
A triangle will appear on your screen. Connect your phone with pc. In odin you will see that the left bar will turn yellow with the word COM in it. That means your phone is connected and ready to flash.
Then press start, wait till install is complete. See my previous post
thankx
i will try and will report to you accordingly
jayebraham said:
thankx
i will try and will report to you accordingly
Click to expand...
Click to collapse
Mate
What Donovan662 saying should work a treat.
There is a full guide here -> http://forum.xda-developers.com/showthread.php?t=1494493
I used that guide to root and upgrade my i9000 to Slim Bean (4.1.2)
have a look here -> http://youtu.be/emmjfye2Sdk
Hope it helps...