Guys right now i m using JPH in India...to avail warranty i need to get back to DDJG4 which is the official software thru kies...pls help me how to get back to DDJG4 thru ODIN and pls give in details...sorry but i m new so i dont knw the method...tnx...
justsimple1 said:
Guys right now i m using JPH in India...to avail warranty i need to get back to DDJG4 which is the official software thru kies...pls help me how to get back to DDJG4 thru ODIN and pls give in details...sorry but i m new so i dont knw the method...tnx...
Click to expand...
Click to collapse
Download stock firmware from http://www.samfirmware.webs.com/
Download ODIN and keep ur phone in download mode....
connect ur phone to PC...
use odin and take ur downloaded firmware in it and select repartition and press start over that's it.........
kingharsha said:
Download stock firmware from http://www.samfirmware.webs.com/
Download ODIN and keep ur phone in download mode....
connect ur phone to PC...
use odin and take ur downloaded firmware in it and select repartition and press start over that's it.........
Click to expand...
Click to collapse
tnx...ill try this...bt in wat file should i take the download firmware...i mean pit? pda? modem?...???
Hey justsimple1
Dost rush through things if you are using odin for the first time.
Gather as much info as you can by reading through forum and clear all the doubts
Download firmware and 512.pit file from samfirmware.com and extract
Steps (Which I follow)
start Odin (if on vista/7 right click and start as administrator)
Tick Re-Partition
select 512.pit file
Put phone in download mode (VLm Down + home + power)
Plug in the phone and wait until Odin finds it.
Click "Start"
after some time Odin will display "Reset"
Wait until Odin indicates "Pass".
Plug out your phone, remove the battery, put it back in and put phone to download mode again.
Click "Reset" button in Odin and untick "Re-Partition" box.
DO NOT select PIT file again.
if you have ony one .tar file then click PDA and select file
if three files them
Click "PDA" and select CODE file.
Click "MODEM" and select MODEM file.
Click "CSC" and select CSC file.
Plug in the phone and wait until Odin finds it.
Click "Start" button and wait until phone reboots with the new software version.
This method was originally posted by Richthofen (all credits to him), I have used it sucessfully over several flashes.
Which version of odin is bestv and is there an official site to download it from
Sent from my GT-I9000M using XDA App
Please can you tell me how to install a new kernal through odin?
most kernels here have a CWM version which you can flash without odin, I recommend that!
There is also an app called "sgs kernel flasher" which allows you to flash a kernel right within the running phone!
If you want to use odin, chose pda and no repartion and no pit...
mimicuk said:
Please can you tell me how to install a new kernal through odin?
Click to expand...
Click to collapse
Have you used Odin before ?
1. Put phone in to download mode
2. do not connect phone to usb
3. start odin, select your kernel.tar in the pda selection
4. uncheck re-partition - check auto reboot
5. connect phone to usb - odin will diplay "added" in the txt scroll
6. press start
7. Odin will do it thing & if successful will display a "success 1/failed 0" line in the txt scroll
8. phone will reboot & your good to go.
Remember you do this at your own risk
Thankyou very much
Could some one for benefit of Indian Tab Owners, write a step-by-step instructions or guide. Lot of information to digest for a new user including details of 1) rooting 2) installing recovery 3) flashing ... this information would be great useful for everyone.
My Tab details :
(Model: GT-P1000 | Code: INU | Version: P1000DDJK3/P1000ODDJJ1/P1000DDJJ1)
hey..even i have a galaxy tab indian version...just follow the guides that are avaliable here for rooting flashing etc...etc...and i had the same modem when i bought it but its since been upgraded to a newer version of the modem so i just updated the modem to the ...DXJM2 version..thought the asian modem would be better for me..if u want i'll post the modem.bin
Dare{D}evil said:
hey..even i have a galaxy tab indian version...just follow the guides that are avaliable here for rooting flashing etc...etc...and i had the same modem when i bought it but its since been upgraded to a newer version of the modem so i just updated the modem to the ...DXJM2 version..thought the asian modem would be better for me..if u want i'll post the modem.bin
Click to expand...
Click to collapse
Thank you for quick reply. I started compiling the files need to flashing. So far, I could do following. Please advice me whether I am on the right path or not.
1. Rooted my tab with Z4root. Now I got root permission.
2. Downloaded Odin3 v1.7.exe and s1_odin_20100803.pit for flashing
3. Downloaded Roto-JMI-Full-v2.zip and Roto-JMI-Upgrade-v2.zip
Now, using Odin PDA button, I want to flash Roto-JMI-Full-v2.zip ?
Few questions:
a) Is this correct way of flashing or I am missing something?
b) Does above flash install Recovery also ?
c) which files need for PHONE and CSC files ?
d) Which firmware best suitable for Indian Tab ?
Thank you in advance for clarifying above.
I really appreciated reply for my questions as it would allow me to move forward. I will ensure a good documentation at the end of the process for benefit of other users.
nchary05 said:
Thank you for quick reply. I started compiling the files need to flashing. So far, I could do following. Please advice me whether I am on the right path or not.
1. Rooted my tab with Z4root. Now I got root permission.
2. Downloaded Odin3 v1.7.exe and s1_odin_20100803.pit for flashing
3. Downloaded Roto-JMI-Full-v2.zip and Roto-JMI-Upgrade-v2.zip
Now, using Odin PDA button, I want to flash Roto-JMI-Full-v2.zip ?
Few questions:
a) Is this correct way of flashing or I am missing something?
b) Does above flash install Recovery also ?
c) which files need for PHONE and CSC files ?
MId) Which firmware best suitable for Indian Tab ?
Thank you in advance for clarifying above.
Click to expand...
Click to collapse
Install Adfree or something which requires root acess for installation. Once rooted download something like root explorer from market which allows you to backup the modem.bin file. Or me or somebody else can just upload the file here.
Read the post/link in the thread where you downloaded Roto's JMI rom.
Use the .pit file from Roto's link not the thing which you posted...same place where you got the same ROM file. If you are flashing first time/from another rom then use the Full v2 zip file. Else use Update v2 when flashing from one of Roto's rom.
Connect the tab to your pc, reboot and go into download mode...press power+vol down button while rebooting...a yellow triangle icon with an android digging will come up...to get out of download mode,just keep the power button pressed till it rebooted normally.
Once in download mode, open up Odin and check that the yellow com box option is on. Check repartition option to ensure everything is wiped and you have a fresh install from scratch.
For PIT select the pit file downloaded from roto's link
For PDA select the Full.tar file
For PHONE select the modem.bin file
For CSC leave it blank...
Once done, recheck and hit start.
PLEASE CHECK ROTO'S JMI V2 THREAD IN THE DEVELOPEMENT SECTION...it has a link to howto which is old but gives some idea of how to proceed...for pit, pda, phone follow as I suggested and things will go fine...
Sent from my GT-P1000 using XDA App
Thank you.. I will do the same let you know the status....
blackheart2925 said:
Install Adfree or something which requires root acess for installation. Once rooted download something like root explorer from market which allows you to backup the modem.bin file. Or me or somebody else can just upload the file here.
Read the post/link in the thread where you downloaded Roto's JMI rom.
Use the .pit file from Roto's link not the thing which you posted...same place where you got the same ROM file. If you are flashing first time/from another rom then use the Full v2 zip file. Else use Update v2 when flashing from one of Roto's rom.
Connect the tab to your pc, reboot and go into download mode...press power+vol down button while rebooting...a yellow triangle icon with an android digging will come up...to get out of download mode,just keep the power button pressed till it rebooted normally.
Once in download mode, open up Odin and check that the yellow com box option is on. Check repartition option to ensure everything is wiped and you have a fresh install from scratch.
For PIT select the pit file downloaded from roto's link
For PDA select the Full.tar file
For PHONE select the modem.bin file
For CSC leave it blank...
Once done, recheck and hit start.
PLEASE CHECK ROTO'S JMI V2 THREAD IN THE DEVELOPEMENT SECTION...it has a link to howto which is old but gives some idea of how to proceed...for pit, pda, phone follow as I suggested and things will go fine...
Sent from my GT-P1000 using XDA App
Click to expand...
Click to collapse
I followed the steps after flashing 'full' tar, it rebooted tab, started the normally. After that, I verified that, all applications , phone (GSM) and wifi working fine.
Now my question is do I really need to flash *second* tar file ? what is it for ?
^^No. It is only for people upgrading from previous versions! You are good to go!
Now, I want to install CWM recovery. Please some one can confirm below steps:
1. Make sure to have Samsung Kies installed, and your tab at least connected once, to be sure the drivers are correct.
2. Your Tab must be Rooted.
3. If you wish to do a backup, now is the time.
4. You will need an SD Card with enough free space for the filesystem conversion, and to put the Overcome ROM on before we start. (An empty 4gb should be plenty, as long as it is empty, or close too)
5. Download and Extract the following file to your computer: http://www.apksmash.com/corodius/galaxytab.zip (Contains "Odin3 v.1.7.exe" "Overcome_Kernel_v1.0")
Now, we will Install the Kernel and perform the EXT4 filesystem conversion.
1. Turn off your Galaxy Tab.
2. Turn your Galaxy Tab on into DOWNLOAD mode (Press Volume DOWN and Power On at the same time).
3. Open Odin3 v1.7.exe on your PC.
4. Connect your Galaxy Tab to your PC via the USB cable.
5. Make Sure the ID:COM box is highlighted yellow (meaning it sees your tab).
6. Click on the PDA button and select the Overcome_Kernel_v1.0.tar file you downloaded earlier (make sure PDA is ticked after selecting the file).
7. The only boxes ticked should be:
A. Auto Reboot
B. F. Reset Time
C. The PDA tickbox
8. Click start and wait for PASS! to show highlighted green on Odin.
9. Your Galaxy Tab will Reboot, and get stuck on the Samsung Boot Screen. This is fine.
10. Turn your Galaxy Tab off by holding the power button for about 5 seconds.
11. Turn your Galaxy Tab on into RECOVERY mode (Press Volume UP and Power On at the same time).
12. The Galaxy Tab will now perform the EXT4 conversion.
13. Sit tight, depending on how much data you have, this can take quite a long time.
14. Once finished, click reboot system now (by pressing the power button).
At this point, You have installed the Overcome Kernel with CWM included and converted the Filesystem to EXT4. It has been reported that many stock ROMs will boot and run fine now, however some may not, but it just depends on your ROM etc.
http://forum.xda-developers.com/showthread.php?p=11713685.
Would be there any problem ? or is there any easy way to install CWM Recovery.
I had bricked my tab while modding battery icon and it was not booting now. Now i want to flash with the custom rom available here. I am noob to flashing so just want to confirm the steps mentioned above applicable to the bricked tab. Can somebody guide me for bircked tab.
Please mentioned the good custom rom with Ext4 conversion at the time of install. I am using indian tab.
@OP:- Sorry for hijacking this thread but find some info here for my queries
Can you get into download mode? If yes then you should be able to flash...but I would suggest checking"I bricked my tab" threads in general or developement section...
Sent from my GT-P1000 using XDA App
nchary05 said:
Now, I want to install CWM recovery. Please some one can confirm below steps:
1. Make sure to have Samsung Kies installed, and your tab at least connected once, to be sure the drivers are correct.
2. Your Tab must be Rooted.
3. If you wish to do a backup, now is the time.
4. You will need an SD Card with enough free space for the filesystem conversion, and to put the Overcome ROM on before we start. (An empty 4gb should be plenty, as long as it is empty, or close too)
5. Download and Extract the following file to your computer: http://www.apksmash.com/corodius/galaxytab.zip (Contains "Odin3 v.1.7.exe" "Overcome_Kernel_v1.0")
Now, we will Install the Kernel and perform the EXT4 filesystem conversion.
1. Turn off your Galaxy Tab.
2. Turn your Galaxy Tab on into DOWNLOAD mode (Press Volume DOWN and Power On at the same time).
3. Open Odin3 v1.7.exe on your PC.
4. Connect your Galaxy Tab to your PC via the USB cable.
5. Make Sure the ID:COM box is highlighted yellow (meaning it sees your tab).
6. Click on the PDA button and select the Overcome_Kernel_v1.0.tar file you downloaded earlier (make sure PDA is ticked after selecting the file).
7. The only boxes ticked should be:
A. Auto Reboot
B. F. Reset Time
C. The PDA tickbox
8. Click start and wait for PASS! to show highlighted green on Odin.
9. Your Galaxy Tab will Reboot, and get stuck on the Samsung Boot Screen. This is fine.
10. Turn your Galaxy Tab off by holding the power button for about 5 seconds.
11. Turn your Galaxy Tab on into RECOVERY mode (Press Volume UP and Power On at the same time).
12. The Galaxy Tab will now perform the EXT4 conversion.
13. Sit tight, depending on how much data you have, this can take quite a long time.
14. Once finished, click reboot system now (by pressing the power button).
At this point, You have installed the Overcome Kernel with CWM included and converted the Filesystem to EXT4. It has been reported that many stock ROMs will boot and run fine now, however some may not, but it just depends on your ROM etc.
http://forum.xda-developers.com/showthread.php?p=11713685.
Would be there any problem ? or is there any easy way to install CWM Recovery.
Click to expand...
Click to collapse
I followed above steps and could able to install CWM RECOVER.
congrats dude
maddy_in65 said:
I had bricked my tab while modding battery icon and it was not booting now. Now i want to flash with the custom rom available here. I am noob to flashing so just want to confirm the steps mentioned above applicable to the bricked tab. Can somebody guide me for bircked tab.
Please mentioned the good custom rom with Ext4 conversion at the time of install. I am using indian tab.
@OP:- Sorry for hijacking this thread but find some info here for my queries
Click to expand...
Click to collapse
can you just tel me which modem.bin are u using coz i was planning to flash but stuck on decision bcoz of modem... is it jpz or jk3? or any other
A new GB version is available DDJPA
http://forum.xda-developers.com/showthread.php?t=1226674
need PDA PIT PHONE CSC files
Kindly send me the links for downloading the PDA PIT PHONE CSC files as I could find only broken links.
My samsung tab (Version: P1000DDJK3/P1000ODDJJ1/P1000DDJJ1)) is bricked and won't boot.
Than You
nchary05 said:
Could some one for benefit of Indian Tab Owners, write a step-by-step instructions or guide. Lot of information to digest for a new user including details of 1) rooting 2) installing recovery 3) flashing ... this information would be great useful for everyone.
My Tab details :
(Model: GT-P1000 | Code: INU | Version: P1000DDJK3/P1000ODDJJ1/P1000DDJJ1)
Click to expand...
Click to collapse
hi guys i urgently need help in finding the software that would upgrade my firmware from 2.3.3 to 2.3.6 or above and i cant seem to find the software to root my fone either (gingerbread)
haqqie said:
hi guys i urgently need help in finding the software that would upgrade my firmware from 2.3.3 to 2.3.6 or above and i cant seem to find the software to root my fone either (gingerbread)
Click to expand...
Click to collapse
try thisone:
http://forum.xda-developers.com/showthread.php?t=742403
and you could search for ics-roms instead of 2.3.4
my suggestion:
http://forum.xda-developers.com/showthread.php?t=1664049
Here are some links for going to 2.3.6 and rooting your phone.
How to Install Android 2.3.6 Gingerbread Value Pack on Samsung Galaxy S GT-I9000
Download CF-Root for JVU
CF-Root Installation Instructions in Post #1
Install XXJVU firmware - Here
Then Install Semaphore 2.5.0 - Thread Here - Direct Link to Semaphore 2.5.0 Here
Note that XXJVU isn't the latest 2.3.6 firmware, XXJW6 is. If you wanted to install that then the procedure is essentially the same you'll just need the XXJW6 files and CF-root or semaphore kernel for XXJW6 (i'm not sure if there is a semaphore kernel for XXJW6). But running a rooted XXJVU firmware is good enough, especially if you're gonna flash a custom rom. There aren't many differences between XXJVU and XXJW6
Here's some detailed instructions on the process;
Before you flash:
1.Backup all your important files and data
2. Download the JVU stock firmware and the (Download links provided above)
3. Make sure your phone is fully charged.
4.Disable and kill the Kies process from task manager in windows on your pc. It will interupt the flashing process.
5.This guide is strictly for Samsung Galaxy S i9000 only.
*Caution
Update your phone at your own risk. I am not, nor is anyone else, responsible for any damage of your devices arising from your usage on this tutorial or guide.
How to install JVU stock Firmware:
First, you need to flash the JVU stock firmware using odin.
After downloaded, extract the folder. The files included as followed:
CODE_I9000XXJVU_CL851880_REV03_user_low_ship.tar.md5
GT-I9000-CSC-MULTI-OXAJVU.tar.md5
MODEM_I9000XXJVU_REV_00_CL1092175.tar.md5
s1_odin_20100512.pit
Odin3
Launch the Odin3.
Put all the files into the respective fields in Odin3.
PIT: s1_odin_20100512.pit
PDA: CODE_I9000XXJVU_CL851880_REV03_user_low_ship.tar.md5
PHONE: MODEM_I9000XXJVU_REV_00_CL1092175.tar.md5
CSC: GT-I9000-CSC-MULTI-OXAJVU.tar.md5
Tick the Re-Partition
Reboot your phone into download mode (Press volume down + Home +Power Button). Yellow triangle will shown when reboot into download mode.
Connect your phone with PC via USB cable. Yellow ID:COM will shown if your device is detected.
After all the files are set, then click Start and your phone will be installed with JVU stock firmware.
After success, your phone will be reboot and JVU is installed. The setup wizard will shown up when as the phone rebooted, and make sure no boxes are ticked. If any boxes are ticked as default, please un-tick it. You can change your settings later.
Warning. Do not tick any box at first boot on set-up wizard!!! You can change the setting manually later. If the box is tick as default, please un-tick it.
How to install custom kernel (semaphore)?
Download the semaphore kernel.
Assume the Odin3 is still open, click Reset to reset all the field.
Put the downloaded ZIP files at PDA section
PDA: Semaphore_kernel_JVU_2.5.0beta.tar
Make sure the Re-partition is now un-ticked.
Reboot your phone into download mode (Press volume down + Home +Power Button). Yellow triangle will shown when reboot into download mode.
Connect your phone with PC via USB cable. Yellow ID:COM will shown if your device is detected.
After all the files are set, then click Start. It takes about 10 seconds and your phone will reboot.
Semaphore icon will be added in your phone's app menu. Go to setting and check the kernel version.
Zorigo said:
Install XXJVU firmware - Here
Then Install Semaphore 2.5.0 - Thread Here - Direct Link to Semaphore 2.5.0 Here
Note that XXJVU isn't the latest 2.3.6 firmware, XXJW6 is. If you wanted to install that then the procedure is essentially the same you'll just need the XXJW6 files and CF-root or semaphore kernel for XXJW6 (i'm not sure if there is a semaphore kernel for XXJW6). But running a rooted XXJVU firmware is good enough, especially if you're gonna flash a custom rom. There aren't many differences between XXJVU and XXJW6
Here's some detailed instructions on the process;
Before you flash:
1.Backup all your important files and data
2. Download the JVU stock firmware and the (Download links provided above)
3. Make sure your phone is fully charged.
4.Disable and kill the Kies process from task manager in windows on your pc. It will interupt the flashing process.
5.This guide is strictly for Samsung Galaxy S i9000 only.
*Caution
Update your phone at your own risk. I am not, nor is anyone else, responsible for any damage of your devices arising from your usage on this tutorial or guide.
How to install JVU stock Firmware:
First, you need to flash the JVU stock firmware using odin.
After downloaded, extract the folder. The files included as followed:
CODE_I9000XXJVU_CL851880_REV03_user_low_ship.tar.md5
GT-I9000-CSC-MULTI-OXAJVU.tar.md5
MODEM_I9000XXJVU_REV_00_CL1092175.tar.md5
s1_odin_20100512.pit
Odin3
Launch the Odin3.
Put all the files into the respective fields in Odin3.
PIT: s1_odin_20100512.pit
PDA: CODE_I9000XXJVU_CL851880_REV03_user_low_ship.tar.md5
PHONE: MODEM_I9000XXJVU_REV_00_CL1092175.tar.md5
CSC: GT-I9000-CSC-MULTI-OXAJVU.tar.md5
Tick the Re-Partition
Reboot your phone into download mode (Press volume down + Home +Power Button). Yellow triangle will shown when reboot into download mode.
Connect your phone with PC via USB cable. Yellow ID:COM will shown if your device is detected.
After all the files are set, then click Start and your phone will be installed with JVU stock firmware.
After success, your phone will be reboot and JVU is installed. The setup wizard will shown up when as the phone rebooted, and make sure no boxes are ticked. If any boxes are ticked as default, please un-tick it. You can change your settings later.
Warning. Do not tick any box at first boot on set-up wizard!!! You can change the setting manually later. If the box is tick as default, please un-tick it.
How to install custom kernel (semaphore)?
Download the semaphore kernel.
Assume the Odin3 is still open, click Reset to reset all the field.
Put the downloaded ZIP files at PDA section
PDA: Semaphore_kernel_JVU_2.5.0beta.tar
Make sure the Re-partition is now un-ticked.
Reboot your phone into download mode (Press volume down + Home +Power Button). Yellow triangle will shown when reboot into download mode.
Connect your phone with PC via USB cable. Yellow ID:COM will shown if your device is detected.
After all the files are set, then click Start. It takes about 10 seconds and your phone will reboot.
Semaphore icon will be added in your phone's app menu. Go to setting and check the kernel version.
Click to expand...
Click to collapse
Very detailed explanation, too bad the guy doesn't even say thanks.
Slim 4.2_Semaphore 1.2.5s_Cobalt Theme
vanisleryan said:
Very detailed explanation, too bad the guy doesn't even say thanks.
Slim 4.2_Semaphore 1.2.5s_Cobalt Theme
Click to expand...
Click to collapse
All too common unfortunately.....
i think its my fault i try to this method.. but i didnt see it was for 19000
heres the link : http://forum.xda-developers.com/showthread.php?t=1993937
my question is : how can fix this? my phone wont open (
by : Donovan662
Get in download mode & flash this JVT rom with odin with pit & repartition ticked & the 2 next to it also
http://db.tt/sJ2uJB3F
Here is an example:
PDA, select CODE_I9000XXJVS_CL565837_REV03_user_low_ship.tar
Phone, select MODEM_I9000XXJVS_REV_00_CL1059471.tar )
CSC, select GT-I9000-CSC-MULTI-OXAJVS.tar
PIT, select s1_odin_20100512.pit
When pass it reboots automaticly & install.
Done installing turn off Phone & Get in download mode again
Flash this cf root with odin in Pda section
http://db.tt/9jugXMKM
After that it reboots and a cwm icon will appear. Click on it allow & there is an option reboot into recovery.
From there u can flash a custom rom of your choice. Do a full wipe (data, cache, dalvik before).
It may be that you have to flash custom 2 or 3 times...
marpycoco said:
i think its my fault i try to this method.. but i didnt see it was for 19000
heres the link : http://forum.xda-developers.com/showthread.php?t=1993937
my question is : how can fix this? my phone wont open (
by : Donovan662
Get in download mode & flash this JVT rom with odin with pit & repartition ticked & the 2 next to it also
http://db.tt/sJ2uJB3F
Here is an example:
PDA, select CODE_I9000XXJVS_CL565837_REV03_user_low_ship.tar
Phone, select MODEM_I9000XXJVS_REV_00_CL1059471.tar )
CSC, select GT-I9000-CSC-MULTI-OXAJVS.tar
PIT, select s1_odin_20100512.pit
When pass it reboots automaticly & install.
Done installing turn off Phone & Get in download mode again
Flash this cf root with odin in Pda section
http://db.tt/9jugXMKM
After that it reboots and a cwm icon will appear. Click on it allow & there is an option reboot into recovery.
From there u can flash a custom rom of your choice. Do a full wipe (data, cache, dalvik before).
It may be that you have to flash custom 2 or 3 times...
Click to expand...
Click to collapse
You can't power it on? No download mode? If no download mode, then you probably hardbricked it. Try USB jig or go to service center.
ty sir for the answer i will try usb jig