Super Combo problem in my xperia x8..... - XPERIA X8 Q&A, Help & Troubleshooting

Well this is my first post here.
To be very short this is not a totally new problem. This is a combination of many problems that has made me totally helpless.
I had rooted my device using x8toolbox beta4, and installed a Gingerxperia V21 custom ROM.
After that i tried unlocking the bootloader, but flashtools continuously kept saying that my device was in MTP mode and strange enough there was no option in my phone's settings to change it.
So I went back to x8toolbox planning on installing the stock ROM back, when i saw busybox installer within.
I installed busybox 1.19.0 and then i asked x8toolbox to check the digitizer on my phone, AND THERE IT STARTED REBOOTING OVE AND OVER.
So now my phone can't connect to my pc for PCC repair or flashtools as MTP mode can't be switched off (and my phone won't turn on for the sd card to be read). And i am stuck with the Sony Ericsson Logo.
Please help me.....thanks in advance.

U have soft bricked your x8.
U can reset your x8 to original 2.1 with the help of following steps.
It's easy. Do it and rooted your phone again
forum.xda-developers.com/showthread.php?t=1570523
Officially corp via W8

Or just try Flashtool

i think your problem is flashing driver.. try to install on /flashtool/drivers/ the name of drivers is gordon gate.. but if your have a same problem after installed drivers, check your drivers on my computer/drivers.. or try for flashing on other computer..

leecorp said:
U have soft bricked your x8.
U can reset your x8 to original 2.1 with the help of following steps.
It's easy. Do it and rooted your phone again
forum.xda-developers.com/showthread.php?t=1570523
Officially corp via W8
Click to expand...
Click to collapse
Thanks for your answer..... But as I said my phone is still in MTP mode and doesn't seem to snap out of it. As i plug in my phone it turns on the green light and then starts rebooting as usual. Is it my driver 's issue? or is it just the mtp mode?? flashtool also says the same thing..:crying:

U cant keep it longer.
Open flashtool then select firmware and ok.
Wait till a screen appear.
Now connect ur phone by holiding back button.
Sent from my X8 using Tapatalk 2

bandarigoda123 said:
U cant keep it longer.
Open flashtool then select firmware and ok.
Wait till a screen appear.
Now connect ur phone by holiding back button.
Sent from my X8 using Tapatalk 2
Click to expand...
Click to collapse
But flashtools shows ERROR and flashing aborted and says that for 2011 line devices make sure your device is not in mtp mode....
Flashtools doesn't work that way....

Remember , wana unlock bootloader use stock rom to unlock. Do not use any install custom rom to unlock. Thing u have made a misstake.

kakho55 said:
Remember , wana unlock bootloader use stock rom to unlock. Do not use any install custom rom to unlock. Thing u have made a misstake.
Click to expand...
Click to collapse
So what to do now? Even if i can get my phone back can i unlock the bootloader (manufact. code: 11W33) ????
Help me plzz...

livinglegend9894 said:
So what to do now? Even if i can get my phone back can i unlock the bootloader (manufact. code: 11W33) ????
Help me plzz...
Click to expand...
Click to collapse
DONT UNLOCK!!!!!!!!!! HARD BRICK!
Sent from my E15i using xda premium

Don't try to unlock the Bootloader
If the error getting further, Re-install Windows.
It can't be, 3 weeks ago I had the same problem (MTP) .
I can't even install Apps via flashtool, so I try to connect to flashmode.
It works.
As I said try to Re-install windows.
Good Luck.

Related

I can't Connect My Bricked Phone..

Hello Xda... I Can't Connect My bricked Phone to Pc. When i put it and turn it on flash mode it tells that failed to install the device drivers. Seus , PC Companion , Flashtool Can't Recognize it. can anyone help me? Thanks In advance.
First of all how you broke it? Second before you can proceed with seus or any other tool you need to install all drivers for your phone.....
Sent from my E15 using XDA App
dsaklein said:
First of all how you broke it? Second before you can proceed with seus or any other tool you need to install all drivers for your phone.....
Sent from my E15 using XDA App
Click to expand...
Click to collapse
i installed CM7 rom from NaA the new one , without the custom kernel. i can't go to recoveries. how can i fix it ?
eu8umhc said:
i installed CM7 rom from NaA the new one , without the custom kernel. i can't go to recoveries. how can i fix it ?
Click to expand...
Click to collapse
How far does your phone boot-up?
Do you still see something on your screen?
Does the LED still light up (when connected to the charger/USB)?
If you haven't killed the boot-loader you should be able to recover the device with Flashtool ... if the boot-loader is dead I think there's no easy way to resurrect it.
Of course the unsolved question is if it would need a intact kernel as well AND if custom kernels actually support "Flash mode".
B.Jay said:
How far does your phone boot-up?
Do you still see something on your screen?
Does the LED still light up (when connected to the charger/USB)?
If you haven't killed the boot-loader you should be able to recover the device with Flashtool ... if the boot-loader is dead I think there's no easy way to resurrect it.
Of course the unsolved question is if it would need a intact kernel as well AND if custom kernels actually support "Flash mode".
Click to expand...
Click to collapse
i See The Flash Mode Green LEd yes. When I Start it, i see the SOny ericsson logo and it stucks there. i try to connecto to pc and it can't install drivers for device. how can i rescue it? tommorow i have a lesson and i need it :S and also it tells that cant recognized.
B.Jay said:
How far does your phone boot-up?
Do you still see something on your screen?
Does the LED still light up (when connected to the charger/USB)?
If you haven't killed the boot-loader you should be able to recover the device with Flashtool ... if the boot-loader is dead I think there's no easy way to resurrect it.
Of course the unsolved question is if it would need a intact kernel as well AND if custom kernels actually support "Flash mode".
Click to expand...
Click to collapse
Finally I did it! Big Thanks to you. I Installed the drivers and it recognized. big thanks
Well, that's exactly from where Vlackrs and I already recovered our phones after a bad flash ("stuck at the Sony Ericsson logo").
Start Flashtool and select "Check drivers".
If it turns out as "OK" on all three checks it seems you have the drivers installed already.
If not ... try to install Gordon's Gate (should be included with Flashtool and called "ggsetup.exe").
Follow the instructions I wrote up here to restore the device.
Note that I did NOT use Flashtool 0.5 as 0.5.0.0, 0.5.0.1 and 0.5.0.2 failed to recognize the device (and yes, I replaced the "E15.properties" with the files posted in the Flashtool thread in the Development section) - Flashtool 0.2.9.1 did the trick for us.
Edit
eu8umhc said:
Finally I did it! Big Thanks to you. I Installed the drivers and it recognized. big thanks
Click to expand...
Click to collapse
Ok - good you got the driver problem resolved ... seems I was too slow writing up my post.
B.Jay said:
Well, that's exactly from where Vlackrs and I already recovered our phones after a bad flash ("stuck at the Sony Ericsson logo").
Start Flashtool and select "Check drivers".
If it turns out as "OK" on all three checks it seems you have the drivers installed already.
If not ... try to install Gordon's Gate (should be included with Flashtool and called "ggsetup.exe").
Follow the instructions I wrote up here to restore the device.
Note that I did NOT use Flashtool 0.5 as 0.5.0.0, 0.5.0.1 and 0.5.0.2 failed to recognize the device (and yes, I replaced the "E15.properties" with the files posted in the Flashtool thread in the Development section) - Flashtool 0.2.9.1 did the trick for us.
Edit
Ok - good you got the driver problem resolved ... seems I was too slow writing up my post.
Click to expand...
Click to collapse
It's ok . the info you gave me is important. now i will read the link you gave me. Big Thanks Again..
can someone help me please...i restored a backup of gingerdx and after that i'm stuck in SE screen and led not working when connected to pc

[Q] Xperia x8 bricked

Please help i just isntalled new ROM for my xperai x8 and now when i restarted it it is stuck at SE logo and stays there.I tried to enter to xrecovery but it cant enter like i dont have xrecovery but i actually do. Now when i try to put my phoen i nflash mode it says taht my usb device isnt recognised but it was a day ago. Moreover i reinstalled windwos usb drivers and Xperia SEMC flash drivers to see if this is the problem but its not it still cant recognise it so i am stuck at SE logo , xrecovery cant run , myPC doesnt recognise the phone in flash mode.... Please help !
This method will install the original software on your X8!
If you have Sony PC Companion 2.1 on your PC, then uninstall it, and download and install Sony PC Companion 2.1, again! If not, then PC Companion might not recognize your phone. After installing do the following:
- Turn off the phone, and unplug it from the PC
- Turn on Sony PC Companion on your PC
- In PC Companion, enter the Support Zone tab
- Go to Update Phone Software
A window will pop out, saying that it cannot find your phone
- Click on Fix Phone
- Click on Continue
A window will pop out, saying that you will lose all your data
- TICK the BOX
- Click on continue
An update process will began.
Wait for it to show a window with all the SONY mobile phones
- Find your phone (X8)
- Click on the phone.
Now all you have to do is follow the on-screen instructions. It will tell you to hold the back button and plug your turned-off X8 to the PC, then it will erase everything, and download the original 2.1 ROM to your X8.
yes
WhatWhatInTheButt said:
This method will install the original software on your X8!
If you have Sony PC Companion 2.1 on your PC, then uninstall it, and download and install Sony PC Companion 2.1, again! If not, then PC Companion might not recognize your phone. After installing do the following:
- Turn off the phone, and unplug it from the PC
- Turn on Sony PC Companion on your PC
- In PC Companion, enter the Support Zone tab
- Go to Update Phone Software
A window will pop out, saying that it cannot find your phone
- Click on Fix Phone
- Click on Continue
A window will pop out, saying that you will lose all your data
- TICK the BOX
- Click on continue
An update process will began.
Wait for it to show a window with all the SONY mobile phones
- Find your phone (X8)
- Click on the phone.
Now all you have to do is follow the on-screen instructions. It will tell you to hold the back button and plug your turned-off X8 to the PC, then it will erase everything, and download the original 2.1 ROM to your X8.
Click to expand...
Click to collapse
thanks mate i will try it now
lol
It doesn't work it says that Pc companion was not able to connect to the device. I tried many things bu pc companion just cant connect my phone and windows keep saying that error that i am plugging unknown device which is a bull**** the day before it was working fine...
For all people who didnt understand iCANT ENTER IN FLASH MODE I MEAN I CAN BUT ITS NOT RECOGNISED so i cant update my software.
also
also flash tool in the console says that it cant determine what deviec i am plugging into and cant display what is busybox version or anything like i am putting an unknown device...
27/043/2012 15:43:10 - ERROR - Cannot identify your device. Found sh while expecting X10, E10, U20 or E15 (read from ro.product.model from build.prop)
Hey there, my phone isn't bricked...but I think I have too much data (possibly conflicting roms installed at the same time??) and I wish to reset my phone to its original status... I wish to re-install a ROM on it, but I want to start fresh again by removing the rooting programs or what have you..
Would following these steps put it all back to its original setting, also meaning that I could completely wipe the SD clean?
If so, would this mean I would have to re-root my X8? Not that it would be a problem but I would just like to know if it would be needed!
Thanks!
Regards,
Nev51289
yes
Nev51289 said:
Hey there, my phone isn't bricked...but I think I have too much data (possibly conflicting roms installed at the same time??) and I wish to reset my phone to its original status... I wish to re-install a ROM on it, but I want to start fresh again by removing the rooting programs or what have you..
Would following these steps put it all back to its original setting, also meaning that I could completely wipe the SD clean?
If so, would this mean I would have to re-root my X8? Not that it would be a problem but I would just like to know if it would be needed!
Thanks!
Regards,
Nev51289
Click to expand...
Click to collapse
Yes do as the guy above said...No need to root your phone
Sorry, just to clarify - you mean I wouldn't need to go through the whole rooting process again after doing a full reset/wipe what have you? Thanks by the way
lol
Nev51289 said:
Sorry, just to clarify - you mean I wouldn't need to go through the whole rooting process again after doing a full reset/wipe what have you? Thanks by the way
Click to expand...
Click to collapse
if you want to restore the stock rom (original androdi on xperia x8) with pc Comapnion than you dont need to root it again. But if you want to change it to custom rom and you have done full wipe i think you should root it again (rooting is done so taht you can change the busybox version of the phone and upload xrecovery if you have those you don't need to root)
eastman47 said:
It doesn't work it says that Pc companion was not able to connect to the device. I tried many things bu pc companion just cant connect my phone and windows keep saying that error that i am plugging unknown device which is a bull**** the day before it was working fine...
For all people who didnt understand iCANT ENTER IN FLASH MODE I MEAN I CAN BUT ITS NOT RECOGNISED so i cant update my software.
Click to expand...
Click to collapse
Why don't you download the store Rom annd use Flashtool to flash it? Then you may be able to upgrade to latest revision with PCC.
eastman47 said:
if you want to restore the stock rom (original androdi on xperia x8) with pc Comapnion than you dont need to root it again. But if you want to change it to custom rom and you have done full wipe i think you should root it again (rooting is done so taht you can change the busybox version of the phone and upload xrecovery if you have those you don't need to root)
Click to expand...
Click to collapse
Can I consequently delete Busybox? If it is a deleteable app that is!
use the update service
eastman47 said:
It doesn't work it says that Pc companion was not able to connect to the device. I tried many things bu pc companion just cant connect my phone and windows keep saying that error that i am plugging unknown device which is a bull**** the day before it was working fine...
For all people who didnt understand iCANT ENTER IN FLASH MODE I MEAN I CAN BUT ITS NOT RECOGNISED so i cant update my software.
Click to expand...
Click to collapse
Yeah, I lost you somewhere... If after taking out the battery, you CAN NOT enter xrecovery or CWM, then, you either can try THIS THREAD <--- go on, click on it!, or, you have to do what I had to do a couple of times, which is to restore your X8 to its original state, and to do that with Sony PC Companion, you first have to UNINSTALL your current PC Companion!!! THEN, restart your PC, and install a clean version of Sony PC Companion 2.1!
IT DOESN'T MATTER IF YOU HAVE THE LATEST VERSION of PC Companion, YOU STILL HAVE TO UNINSTALL IT, AND INSTALL IT AGAIN!!! IF YOU DON'T, THERE's a 99% CHANCE THAT PC COMPANION WILL NOT RECOGNIZE YOUR PHONE!!! ...I don't know why, but it's probably some marketing trick, since I once used this method 3 times in a row, then the fourth time PC Companion didn't recognize my X8. This happened on both, the old PC Companion, and the current Sony version 2.1. I tested them both on purpose, to eliminate the possibility that I damaged my X8's hardware somehow, during a high speed impact collision with the bedroom wall...
Once you reinstall Sony PC Companion 2.1, go back to my first post to your problem, and follow it step-by-step.
AND yes, if you want to install custom ROM's again, then you will have to ROOT your phone again, and UNLOCK the BOOTLOADER, etc...
BUT, if it's a soft-brick, then you might be able to redeem yourself
ViVA FIDELINO!
how about kernel?
WhatWhatInTheButt said:
This method will install the original software on your X8!
If you have Sony PC Companion 2.1 on your PC, then uninstall it, and download and install Sony PC Companion 2.1, again! If not, then PC Companion might not recognize your phone. After installing do the following:
- Turn off the phone, and unplug it from the PC
- Turn on Sony PC Companion on your PC
- In PC Companion, enter the Support Zone tab
- Go to Update Phone Software
A window will pop out, saying that it cannot find your phone
- Click on Fix Phone
- Click on Continue
A window will pop out, saying that you will lose all your data
- TICK the BOX
- Click on continue
An update process will began.
Wait for it to show a window with all the SONY mobile phones
- Find your phone (X8)
- Click on the phone.
Now all you have to do is follow the on-screen instructions. It will tell you to hold the back button and plug your turned-off X8 to the PC, then it will erase everything, and download the original 2.1 ROM to your X8.
Click to expand...
Click to collapse
>> how about kernel? for example your phone allready back to 2.1 rom and you are using custom kernel before i done this update? like kernel aA-11? is it possible to turn on phone even if im using custom kernel? please give me steps how to bring it back, because im currenty using mini cm7 / kernel aA-11, and i want to bring back my xperia x8 to original rom and kernel
Try downloading the stock rom and a diff version of flashtool. I can't remembet which version is most recommended (try searchibg xda - i read it here). install drivers in flashtool's driver folder (gordon's gate) then try again. Almost the same thing happened to me. PCC won't recognize my phone so I couldn't install the drivers.
X8 stuck at SE logo
I am facing same problem. I have been using GingerDX for long time wanted to change the ROM, however after I change the rom through Xrecovery. Phone restarted and stuck at SE logo.
I tried with SE PC companion but it gives error.
I tried Flashtool, used different ftf file but cant help.
Please help. I am unable to start phone....Please guide me...
Maybe u can also try sus (sony update service). I have experience this n done with sus.
Me n my W8:-D
Vishal9890 said:
I am facing same problem. I have been using GingerDX for long time wanted to change the ROM, however after I change the rom through Xrecovery. Phone restarted and stuck at SE logo.
I tried with SE PC companion but it gives error.
I tried Flashtool, used different ftf file but cant help.
Please help. I am unable to start phone....Please guide me...
Click to expand...
Click to collapse
The best way, if u still can't get on your phone , is take it to the SE Customer care. And don't tell a word about rooting or anything. Just ask them to repair the phone, saying that one morning, the SE logo kept on popping up.
Sent from my XPERIA W8 using xda platinum
I have YouTube video tutorial on my channel - search GaganSJ1 in YouTube and scroll down till you found
Press thanks if it helped
Sent from my E15i using XDA
eastman47 said:
Please help i just isntalled new ROM for my xperai x8 and now when i restarted it it is stuck at SE logo and stays there.I tried to enter to xrecovery but it cant enter like i dont have xrecovery but i actually do. Now when i try to put my phoen i nflash mode it says taht my usb device isnt recognised but it was a day ago. Moreover i reinstalled windwos usb drivers and Xperia SEMC flash drivers to see if this is the problem but its not it still cant recognise it so i am stuck at SE logo , xrecovery cant run , myPC doesnt recognise the phone in flash mode.... Please help !
Click to expand...
Click to collapse
check out this video http://www.youtube.com/watch?v=l7B-7tDaB5U
press thanks if it helped

Stuck into black screen X8

I think i have bricked my phone. . My phone stuck into the black screen when i power on where is only shows "sony erricson". SO i can't go to the xrecovery to recover my previous system . any one knows any solution
Heres the .ftf file of stock rom
http://forum.xda-developers.com/showthread.php?t=1101296
Flash it using flash tool..
U will get back the s.e 2.1 romed x8..
Sent by the walking walkman..
Here's guide to using flash tool...
http://forum.xda-developers.com/showthread.php?t=1755215
Sent by the walking walkman..
open pc c in computer and click update than wait till you get "rapair phone" click on it ald follow steps :good:
sidhart said:
Heres the .ftf file of stock rom
http://forum.xda-developers.com/showthread.php?t=1101296
Flash it using flash tool..
U will get back the s.e 2.1 romed x8..
Sent by the walking walkman..
Click to expand...
Click to collapse
I solved the problem right after that by using software update. Now another problem. I can't root it. When i connet it with superclickone.exe, phone start to connect and disconnect. can this tool make root?
Check these if it helps you..
http://forum.xda-developers.com/showthread.php?t=906195
Sent by the walking walkman..
Which version of superone click u are having..
It worked for me with 2.1.1.0 version..
Sent by the walking walkman..
Do you got debugging on.. And ya do you have pc companion installed...
Sent by the walking walkman..
sidhart said:
Do you got debugging on.. And ya do you have pc companion installed...
Sent by the walking walkman..
Click to expand...
Click to collapse
yeah everything is on.. But can't root
nixon1333 said:
I solved the problem right after that by using software update. Now another problem. I can't root it. When i connet it with superclickone.exe, phone start to connect and disconnect. can this tool make root?
Click to expand...
Click to collapse
U said it does not connect, have you tried connecting it normaly with p.c with debugging on letting the drivers get installed first..
1. Install the PC Companion from SE.
2. Connect Phone to PC also PC Compannion asked for, let Windows find all Drivers.
3. Switch USB-Debugging on, one or two more Drivers will be found.
4. Start SuperOneClick, click on "root". Wait ~10 Seconds to finish.
5. Reboot.
Sent by the walking walkman..
nixon1333 said:
I think i have bricked my phone. . My phone stuck into the black screen when i power on where is only shows "sony erricson". SO i can't go to the xrecovery to recover my previous system . any one knows any solution
Click to expand...
Click to collapse
okay...
if you're still confuse, downgrade your phone!
its last option
downgrade into 2.1 - download this file from files crop X8 E15i 2.1.1.C.0.0._un.ftf
root your phone by flash tool..
then install xrecovery by clicking cross icon on flashtool
OR
download this file (password=cintaindonesia) and extract in your SDcard
after that copy paste three files(busybox, chargemon, xrecovery.tar) in system\bin
and you will get xrecovery
after that
unlock bootloader using flashtool OR s1tool
Flash the latest kernel
backup
factory reset, wipe data, etc
Flash ROM
done!

x8 stucked on sony ericsson screenshot

x8 stucked on sony ericsson screenshot , trying to flash stock rom X8_E15_2.1.1.A.0.6_generic.ftf using flash tool 0.6.9.1 OS Windows 7 but flash tool showing (error - flashing abort)
Awaiting for suggestion.
Thanks
Usb cable lost conection! Its happen to me some times. Just again flash 2.1...... and hold back button to 4% then release it and dont move phone
Sent from my E15i using xda premium
Have u installed gordon gate drivers?
First connect phone then hold press back button untill green light show. Then check if windows recognized it.
Then remove battery.
Go to flash tool select the ftf u want to flash then wait until the dialog appear. Then connect phone (if u unplug before) insert battery hold press back till green light show, now it should be flash
Sent from my X8 using Tapatalk 2
supermiki said:
x8 stucked on sony ericsson screenshot , trying to flash stock rom X8_E15_2.1.1.A.0.6_generic.ftf using flash tool 0.6.9.1 OS Windows 7 but flash tool showing (error - flashing abort)
Awaiting for suggestion.
Thanks
Click to expand...
Click to collapse
sometimes its happen cz :
- drivers not installed correctly (x8 drivers and gordon)
- make sure your unlock BL process work successfully
- check all your hardware connection (cable, usb, etc)
don't forget to have > 60% battery
have you install the driver from /driver folder on the flashtool installed folder??
and dont forget to check the X8 ADB driver and fastboot / flashboot whatever LOL
just check that 2 thing and you shouldnt get any problem
Hey install the gorden gates driver provided with flastool and try again.....
Sent from my E15i using xda premium
Finally I've reflashed the rom but still after the pin code the phone does not hook any opertor and also no access to the applications menu
Reflashed with X8_E15_2.1.1.A.0.6_generic.ftf but the phone works only with no sim. E15i SI 1251-9820
supermiki said:
Reflashed with X8_E15_2.1.1.A.0.6_generic.ftf but the phone works only with no sim. E15i SI 1251-9820
Click to expand...
Click to collapse
dont forget put in your sim card to your phone while flash process dude ..
BlackRabbit1703 said:
dont forget put in your sim card to your phone while flash process dude ..
Click to expand...
Click to collapse
Flashed with sim in the phone
try flash again
this may happened sometimes

Please help to unbrick my xperia z

I am in an awkward situation.
xperia z, 4.2.2 244 rooted stock rom, bootloader locked, usb debug mode off, recovery not installed.
I accidentally corrupted build.prop and the phone bricked.
I cannot use flashtool to flash the stock rom back because usb debug mode is off.
I cannot use Sony update service Pro to force update because it said that "your phone already has the latest available software installed".
I cannot use PC Companion to repair because the software said that "Sony update engine doesn't have software available for your phone".
Please help.
wmiswm said:
I am in an awkward situation.
xperia z, 4.2.2 244 rooted stock rom, bootloader locked, usb debug mode off, recovery not installed.
I accidentally disrupted build.prop and the phone bricked.
I cannot use flashtool to flash the stock rom back because usb debug mode is off.
I cannot use Sony update service Pro to force update because it said that "your phone already has the latest available software installed".
I cannot use PC Companion to repair because the software said that "Sony update engine doesn't have software available for your phone".
Please help.
Click to expand...
Click to collapse
Use PC companion but try use repair phone not update. Wait till all phone model showing up than choose your model phone. btw, your phone must off.
than follow instruction there... wil take 1~2 hour for repair.
Hope you can solve your problem. ill take screen shoot when im home later than post here..
Sent from my C6602 using xda premium
YudiA1 said:
Use PC companion but try use repair phone not update. Wait till all phone model showing up than choose your model phone. btw, your phone must off.
than follow instruction there... wil take 1~2 hour for repair.
Hope you can solve your problem. ill take screen shoot when im home later than post here..
Sent from my C6602 using xda premium
Click to expand...
Click to collapse
Thank you very much for your reply. But I am already using the PC Companion repair option, and the response is as stated above.
flashtool is all what you need,read the instructions
http://forum.xda-developers.com/showthread.php?t=2240614
Sent from my C6603 using xda premium
Reply
wmiswm said:
I cannot use flashtool to flash the stock rom back because usb debug mode is off
Click to expand...
Click to collapse
You can use Flashtool to flash stock rom, doesn't matter if usb debug mode is on or off (only needed to install recovery or to root)
Download stock rom, install flashtool + drivers and follow screen instructions.. Good Luck! :good:
J have the same problem, yesterday j installed cyanogenmod, now xperia Z was on SONY logo and j can't flash original firmware on flashtool, j can only flash original kernel, but is still on sony logo
SUS says that hasn't new firmware for my phone.
What can j do ????
Thanks in advance
gm007 said:
flashtool is all what you need,read the instructions
http://forum.xda-developers.com/showthread.php?t=2240614
Sent from my C6603 using xda premium
Click to expand...
Click to collapse
many thanks, done.
shysparrow said:
You can use Flashtool to flash stock rom, doesn't matter if usb debug mode is on or off (only needed to install recovery or to root)
Download stock rom, install flashtool + drivers and follow screen instructions.. Good Luck! :good:
Click to expand...
Click to collapse
yes, you are right. Yesterday I check everything on the right panel and it does not work. Today I leave all option unchecked and flash properly. Many thanks anyway.
maxam73 said:
J have the same problem, yesterday j installed cyanogenmod, now xperia Z was on SONY logo and j can't flash original firmware on flashtool, j can only flash original kernel, but is still on sony logo
SUS says that hasn't new firmware for my phone.
What can j do ????
Thanks in advance
Click to expand...
Click to collapse
Just follow the flashtool instruction and re-flash the stock rom first, everything will return to unroot stated. Reroot then and try again.
wmiswm said:
Just follow the flashtool instruction and re-flash the stock rom first, everything will return to unroot stated. Reroot then and try again.
Click to expand...
Click to collapse
Maybe j have other kind of problem, j tried with flashtool but it doesn't start flashing when in flashmode, after a minute phone boots itself continuosly on sony logo.
j tried several times with different PC and different ftf file.
j hope to solve this problem, but how...
maxam73 said:
Maybe j have other kind of problem, j tried with flashtool but it doesn't start flashing when in flashmode, after a minute phone boots itself continuosly on sony logo.
j tried several times with different PC and different ftf file.
j hope to solve this problem, but how...
Click to expand...
Click to collapse
Try this way bro.. Done in many Xperia here..
Solving Bootloop phone/Flash Tool can't Detect your phone.
Your Phone Must Off!! and not connected !!
1. Open Pc Companion
2. Click update on Red ellipse (in Picture 1)
3. Start on Phone/tablet Update (in Picture 2)
4. Click Repair on Next Screen
5. in Next Screen, Read that warning Click Continue if you OK
6. Next Step click on Red Circle than Next...
7. Wait initializing Software (10~30 mnt) or depend your ISP speed
8. After initializin9 All Xperia Phone List Will Show Up.
Choose What Xperia Phone Will you repair ( I choose XZ) than Next..
9. Follow instruction On picture.
( Connect USB on your Phone while Press Vol down )
10. if not Start.. Unplug usb and try plug again ==> same no 9)
11. After start.. Waiting 1~2 Hours till done.
(Read Warning There )
Sent from my C6602 using xda premium
YudiA1 said:
Try this way bro.. Done in many Xperia here..
Solving Bootloop phone/Flash Tool can't Detect your phone.
Your Phone Must Off!! and not connected !!
1. Open Pc Companion
2. Click update on Red ellipse (in Picture 1)
3. Start on Phone/tablet Update (in Picture 2)
4. Click Repair on Next Screen
5. in Next Screen, Read that warning Click Continue if you OK
6. Next Step click on Red Circle than Next...
7. Wait initializing Software (10~30 mnt) or depend your ISP speed
8. After initializin9 All Xperia Phone List Will Show Up.
Choose What Xperia Phone Will you repair ( I choose XZ) than Next..
9. Follow instruction On picture.
( Connect USB on your Phone while Press Vol down )
10. if not Start.. Unplug usb and try plug again ==> same no 9)
11. After start.. Waiting 1~2 Hours till done.
(Read Warning There )
Sent from my C6602 using xda premium
Click to expand...
Click to collapse
Solved...j know that phones must be off, the problem was flashtool, j used other version (beta 4) on other pc running xp instead of win7 and all goes good.
Thanks to all for helping me
Doesnt work.
I cant use flashtool, period.
Are there anyother methods?
theVenerable said:
Doesnt work.
I cant use flashtool, period.
Are there anyother methods?
Click to expand...
Click to collapse
The above didn't work for me because I received error based on my type of phone.
This guide however did help: http://forum.xda-developers.com/showthread.php?t=2240614
I had to reboot windows to a settings to enable unsigned drivers. Installed Flashtool and it's drivers,
First unlocked the bootloader(BLU button, got the IMEI, used the sony form (http://unlockbootloader.sonymobile.com/instructions))
Then I downloaded the stock sony xperia z ftf image, placed it in Flashtool's firmware folder, then flashed it (flash device > flash mode).
Now my phone's working again.
HTH,
George
brick,unbrick,xperia z problem,flashtool
My OS phone in recovery mode (root) got deleted And when I turn on phone stuck on Sony logo And when it is connected to the computer showing error your USB not recognized and Flash mode for use Flashtool doesn't work and the same error shows what should i do?
shayanster said:
My OS phone in recovery mode (root) got deleted And when I turn on phone stuck on Sony logo And when it is connected to the computer showing error your USB not recognized and Flash mode for use Flashtool doesn't work and the same error shows what should i do?
Click to expand...
Click to collapse
If you still can enter custom recovery, you only need flash rom and (with) suitable kernel.
If not, you need Flashtool.
- make sure you have the newest version of flashtool and driver
- connect your phone to pc.
- when computer show error about usb not recognized, go to computer management - device manager. Find something in universal serial bus controller list that have yellow triangle and exclamation mark. right click and remove it
- disconnect your phone then reboot your pc
- install flashtool and driver, reboot pc again
- connect your phone to pc. Now, it should detect your phone.
- do flashing procedure
cmiiw
visualfighter said:
If you still can enter custom recovery, you only need flash rom and (with) suitable kernel.
If not, you need Flashtool.
- make sure you have the newest version of flashtool and driver
- connect your phone to pc.
- when computer show error about usb not recognized, go to computer management - device manager. Find something in universal serial bus controller list that have yellow triangle and exclamation mark. right click and remove it
- disconnect your phone then reboot your pc
- install flashtool and driver, reboot pc again
- connect your phone to pc. Now, it should detect your phone.
- do flashing procedure
cmiiw
Click to expand...
Click to collapse
Thanks for the answer I tried all ways but the problem is not solved .I think the only solution is JTAG box
shayanster said:
Thanks for the answer I tried all ways but the problem is not solved .I think the only solution is JTAG box
Click to expand...
Click to collapse
To use Flashtool put phone in flashmode, it will not work in recovery mode
To put phone in flashmode
Hold power + both volume keys
wait till you feel three vibrations.
Make sure you have installed Z drivers flashmode drivers & fastboot drivers(Setup fille is in driver folder of flashtool)
Keep FTF file in firmware folder of flashtool
Start flashtool
Click the thunder button
select flashmode
select the FTF file
When it tells you to connect phone
Hold volume down key and connect USB it should start flashing
androidtweaker1 said:
To use Flashtool put phone in flashmode, it will not work in recovery mode
To put phone in flashmode
Hold power + both volume keys
wait till you feel three vibrations.
Make sure you have installed Z drivers flashmode drivers & fastboot drivers(Setup fille is in driver folder of flashtool)
Keep FTF file in firmware folder of flashtool
Start flashtool
Click the thunder button
select flashmode
select the FTF file
When it tells you to connect phone
Hold volume down key and connect USB it should start flashing
Click to expand...
Click to collapse
when it is connected into flashmode the computer showing error your USB not recognized
shayanster said:
when it is connected into flashmode the computer showing error your USB not recognized
Click to expand...
Click to collapse
Is it Windows 7 or 8?

Categories

Resources