Stuck in boot - LG Optimus 2x

My LG Optimus 2X from windmobile is stuck in boot screen. I recently rooted my phone which worked perfectly fine than I installed CWM ext which messed things up, phone was hard resetting every time it started up. So I went to the market place and installed CWM and installed recovery from within the app and decided to install [ROM] MIUI v4 2.7.20 [Multilang][New base] [25/07/2012] through the CWM app. It loads up in recovery FINALLY and I installed it. After reboot its just stuck on LG boot screen I cant go into recovery mode either it just reboots and gets stuck at boot screen. is there anything that i can do to recover the phone?

how u tried this? - http://forum.xda-developers.com/showthread.php?t=1006745
i have done it a couple of times after a bad flash on my P990 and it works great.
i got the NVFlash ready, take out the battery and while pushing down Power and Vol. down button i connect the usb cable and it starts up and u can open NVFlash and let it do it's work.

thank you lets see if it works out:fingers-crossed:

puma99dk| said:
how u tried this? - http://forum.xda-developers.com/showthread.php?t=1006745
i have done it a couple of times after a bad flash on my P990 and it works great.
i got the NVFlash ready, take out the battery and while pushing down Power and Vol. down button i connect the usb cable and it starts up and u can open NVFlash and let it do it's work.
Click to expand...
Click to collapse
hey so NVFlash did work but now i am getting no signal, I went to settings> About phones > baseband: unknown. So I decided to use smart flash and flash the "LG_P990_1035_21_2011-06-22", it just wouldn't flash it loads up to 50% than i get timed out error. Is there anyway to fix this issue.
Thanks.

ali2k4 said:
hey so NVFlash did work but now i am getting no signal, I went to settings> About phones > baseband: unknown. So I decided to use smart flash and flash the "LG_P990_1035_21_2011-06-22", it just wouldn't flash it loads up to 50% than i get timed out error. Is there anyway to fix this issue.
Thanks.
Click to expand...
Click to collapse
this might be an issue with BB and RIL combination...try to install the GetRIL app from the play store and try to install a recommended RIL....reboot and check...
you can try the smartflash after trying this...
Hope this helps

The problem was that I was flashing p990 firmware on my P999. oddly enough it ran but without any baseband. long story short I used the ROM from this thread http://forum.xda-developers.com/showthread.php?p=17258229 and it worked I was in the wrong phone section the whole time. thanks every one for the help couldn't have recovered it without your help thanks :victory:

Related

Need help stuck in LG logo

Dear All,
First i installed cwm recovery from this thread http://forum.xda-developers.com/showthread.php?t=1007863
, it was success but can't do nand backup, so i use rom manager and installed cwm recovery from there and success.
after that i choice boot into cwm recovery from rom manager, phone was restart but stuck in LG logo.
i tried to take out take in the batre and do normal boot on the result is same "stuck in lg logo"
i also tried to enter to cwm recovery by press power + vol down but still same stuck in lg logo
would you please help me ?
Are you holding your fingers on both power and vol down button for long enough? It can take up to 5-6 seconds to enter the CWM
Kickasskev said:
Are you holding your fingers on both power and vol down button for long enough? It can take up to 5-6 seconds to enter the CWM
Click to expand...
Click to collapse
yes, i already tried more than 2 minutes still no enter.
also i already tried smartflash method same problem, there's no driver response
looks like hang in lg logo
Try uninstalling all lg drivers associated with the phone, restart computer then reinstalling all the smartflash drivers then retry
Sent from my LG-P990 using XDA App
Ohh no, Seems like I have the same problem
Ohh no.. Seems like I have the same problem.. The phone is stuck on the LG logo.
I installed the Cyanogen mod successfully, and everything seemed to work.
Then i started Rom manager to install Clockwork recovery. The clockwork mod was stuck the first time, don't know why!
So I restarted the phone, and tried installing the clockwork mod again, this time there were no problems.
After the clockwork mod was installed I wanted to install the Google addons, so I went to Download ROM, and pushed Google Addons. The phone asked for a restart, and during the restart I was stuck on LG logo.
I would be very very happy if anyone can help me?
Hi, i think you must use the nvflash reset-all-phone procedure.
Search google for "NVflash stock ROM release" and you'll find the procedure and the download links for APX drivers and zip with rom images and tools.
Good luck ! (I made the procedure 10 times in 3 days past bricking my phone..)
boezio said:
Hi, i think you must use the nvflash reset-all-phone procedure.
Search google for "NVflash stock ROM release" and you'll find the procedure and the download links for APX drivers and zip with rom images and tools.
Good luck ! (I made the procedure 10 times in 3 days past bricking my phone..)
Click to expand...
Click to collapse
Thank you very much, I succeeded in doing a flash through nvflash, so now my phone works great again
Do you know if you can destroy the nvflash possibly? .. just so I know if I play with the phone as much as I want, and always get it working again with nvflash if something goes wrong
Sent from my LG-P990 using XDA App

[Q] Semi-bricked / Smartflash tool not working

Hi
I'm helping out a friend, which O2X I have rooted and flashed WIUI on to (I previously owned one myself too)
For some reason the phone started to get hot after a while and used up the battery fast, until one day where he couldn't even turn it on again.
Now, he has been trying to fix it himself with NVflash, but no luck, so now its up to me and you guys.
I have used the smartflash tool and flashed the EURO OPEN stock ROM and everything went succesfull, but when the phone reboots, the LG logo appears, and it bootloops.
I tried both with battery and no battery in, but still no cigar.
Any suggestions what I should try next?
PS: If I try to turn on the phone normally, nothing happens. not even a blink from the screen, but I can get into S/W mode and APX
Try lg update tool, choose recover as option, then choose imei as entrance
SuperSkill said:
Try lg update tool, choose recover as option, then choose imei as entrance
Click to expand...
Click to collapse
EDIT: The software says the update is not compatible (dunno if translation is correct, but you get the point)
Update is aborted :/
No more suggestions on what to do?
Tried:
NVflash
Smartflash (Flashed EURO OPEN rom)
LG Update tool (recover function)
The phone still won't boot.
Smartflash is the only solution like you said that the phone can boot in s/w mode try to dig some answer in smartflash thread or search in google i know you can find some answer there
Sent from my Optimus 2X using xda premium
Assuming you have carried out the procedures correctly, looks like this device is actually defective. Probably not what you want to hear, I know, but...
Before giving up completely, you can NVFlash it again (using the original 10C NVFlash from Modaco) and post the log here. Wouldn't get my hopes up though.

[Q] LG P990 Keep Rebooting before going Splash Screen

Hi.
I have LG p990 and it is a rooted mobile and i have tried several CM builds. i was running CM7 build from one month . Today when i tried to power off and than tried to Boot in Recovery mode it didn't booted instead it turn off just shows LG logo and even didnt go to splash screen. even if i try to boot in recovery mode it still do same i tried putting out battery but all in vein . i am very desper from it Please any solution.
cheeta123 said:
Hi.
I have LG p990 and it is a rooted mobile and i have tried several CM builds. i was running CM7 build from one month . Today when i tried to power off and than tried to Boot in Recovery mode it didn't booted instead it turn off just shows LG logo and even didnt go to splash screen. even if i try to boot in recovery mode it still do same i tried putting out battery but all in vein . i am very desper from it Please any solution.
Click to expand...
Click to collapse
Download this and use SmartFlashTool to flash this. It will unbrick your phone but beware you will lose all your data.
Code:
http://forum.xda-developers.com/showthread.php?t=1715272
kalpak2021 said:
Download this and use SmartFlashTool to flash this. It will unbrick your phone but beware you will lose all your data.
Code:
http://forum.xda-developers.com/showthread.php?t=1715272
Click to expand...
Click to collapse
I downloaded the zip and SmartFlashTool, SmartFlashTool won't detect my device . I have properly installed my Mobile driver. if my mobile does't proceed more than starting screen how it will detect my mobile
It worked at last
cheeta123 said:
I downloaded the zip and SmartFlashTool, SmartFlashTool won't detect my device . I have properly installed my Mobile driver. if my mobile does't proceed more than starting screen how it will detect my mobile
Click to expand...
Click to collapse
I found that the given steps won't work with Windows 7 but with Windows XP they worked
cheeta123 said:
Hi.
I have LG p990 and it is a rooted mobile and i have tried several CM builds. i was running CM7 build from one month . Today when i tried to power off and than tried to Boot in Recovery mode it didn't booted instead it turn off just shows LG logo and even didnt go to splash screen. even if i try to boot in recovery mode it still do same i tried putting out battery but all in vein . i am very desper from it Please any solution.
Click to expand...
Click to collapse
Download the mobile driver again, and follow the instructions correctly. Like, removing the battery, press volume down while plugging in until the s/w update screen appears, etc etc. Good luck! Hope it'll boot after the flash.
Sent from my Optimus 2X
Mark
I've a similar-ish issue. I've got CWM installed and can boot into CWM ok. My problem was that I tried to install a ROM (MIUI) and the install had no errors, but when the phone was powered on it hung at the MIUI screen.
So I reverted to a backup successfully and decided to have another go (same problem). This time, after I restore to the backup (which is installed without error by CWM) I can't can't past the initial LG screen. Seems to go into reboot loop.
Any thoughts anyone? If I can get into CWM ok and have a working restore then is there something I'm doing wrong!!
thanks,
Mark

[Q] Bricked After installing CM10

Hi All,
I'm in trouble with my P990.
i was using offical cm10 nightlies for a while and i updated new official cm10 nightlies. After update phone opened and 5 minutes later screen frozen. i removed battery and put it again. But phone not opened again.
I tried NVFlash but NVflash stuck on "waiting for bootloader to initialize" message.
How can i handle this situation.?
Thank you in advance for your help.
yildirimkm said:
Hi All,
I'm in trouble with my P990.
i was using offical cm10 nightlies for a while and i updated new official cm10 nightlies. After update phone opened and 5 minutes later screen frozen. i removed battery and put it again. But phone not opened again.
I tried NVFlash but NVflash stuck on "waiting for bootloader to initialize" message.
How can i handle this situation.?
Thank you in advance for your help.
Click to expand...
Click to collapse
Maybe try to flash any rom with SmartFlash
1.Take out battery
2.replace battery
3.hold Vol- (volume down button) AND power button together until you see the recovery menu. then scroll to Cm updater file and reflash -or- clockwork mod file and flash from backup.
No way!!
When i tried Smartflash pc not found com ports. so i cant flash with this way.
also i tried (JAZZMAN's advice) power and vol- to enter CWM menu but i cant see any thing. (my phone not open)
yildirimkm said:
When i tried Smartflash pc not found com ports. so i cant flash with this way.
also i tried (JAZZMAN's advice) power and vol- to enter CWM menu but i cant see any thing. (my phone not open)
Click to expand...
Click to collapse
How phone must show bootloader or you have installed already CWM it must boot into CWM, if it doesn't show your phone to the service .
yildirimkm said:
When i tried Smartflash pc not found com ports. so i cant flash with this way.
also i tried (JAZZMAN's advice) power and vol- to enter CWM menu but i cant see any thing. (my phone not open)
Click to expand...
Click to collapse
checkfor Rusty's thread for recovery
check for Homero's thread to unbrick with a clean and stock ROM....
LG is 99.999999999% unbrickable AFAIK
Maybe this will work
http://forum.xda-developers.com/showthread.php?t=1975274
Sent from my LG-P990 using xda app-developers app
Service
Thanks for your help.
I couldnt fix my phone. I sent to service. i hope they can fix

[Q] APX doesn't show up after flashing a ROM

ok, so i was using tonyp-harsh v28e vlite ics version before deciding flashing stefan v28g via nvflash
i started nvflash as usual (removing battery + vol up and down), APX driver was recognized and the installation process went smoothly.
the problem is, after i flashed the rom, i found it a lil' bit laggy so i think it'd be better to try CM 10 to find out which one suit me better.
so i turn off my phone again, removing the battery, and pressing vol up & down simultaneously. but then, the phone doesn't respond (yes, it give a blink, but the LG logo doesn't appear and APX doesn't show up in my pc). so, now i'm stuck on v28g
i've tried searching with some queries :
https://www.google.co.id/search?hl=...HMnYrQf7koDADw&ved=0CBwQBSgA&biw=1366&bih=610
https://www.google.co.id/search?q=n...&sugexp=chrome,mod=2&sourceid=chrome&ie=UTF-8
https://www.google.co.id/search?q=l...&sugexp=chrome,mod=2&sourceid=chrome&ie=UTF-8
and such
but it didn't give me an answer
i've also tried another version of nvflash such as this one by ProgMaq and another one by rmein, but nothing works
any suggestion?
babi_perang said:
ok, so i was using tonyp-harsh v28e vlite ics version before deciding flashing stefan v28g via nvflash
i started nvflash as usual (removing battery + vol up and down), APX driver was recognized and the installation process went smoothly.
the problem is, after i flashed the rom, i found it a lil' bit laggy so i think it'd be better to try CM 10 to find out which one suit me better.
so i turn off my phone again, removing the battery, and pressing vol up & down simultaneously. but then, the phone doesn't respond (yes, it give a blink, but the LG logo doesn't appear and APX doesn't show up in my pc). so, now i'm stuck on v28g
i've tried searching with some queries :
https://www.google.co.id/search?hl=...HMnYrQf7koDADw&ved=0CBwQBSgA&biw=1366&bih=610
https://www.google.co.id/search?q=n...&sugexp=chrome,mod=2&sourceid=chrome&ie=UTF-8
https://www.google.co.id/search?q=l...&sugexp=chrome,mod=2&sourceid=chrome&ie=UTF-8
and such
but it didn't give me an answer
i've also tried another version of nvflash such as this one by ProgMaq and another one by rmein, but nothing works
any suggestion?
Click to expand...
Click to collapse
I had the same problem as you face here.
I tried everything NV-flash, smartflash, you name it, no luck. Then I did a emergency repair in the LG updater.
Start the Updater, select "emergency repair", make sure drivers are installed.
Battery out, press Volume Down and connect.
Enter IMEI and S/N and repair program starts.
I had to do it twice, before it finished. I maybe had a bad USB connection or cable, but after "S/W update" showed up in screen on second attempt, I reinserted battery and it went very smooth.
Let it boot.
And then root with NV-flash and you are back in business with normal GB partition table.
I can recommend Tonyp's CWM 6.0.1.5 touch for NV-flash, when you have finished rooting.
It took me 45 minutes, with a not too good internet connection.
PS.: I did not try this one: http://forum.xda-developers.com/showthread.php?t=1715272
but since I could not call up NV-flash, I did not want to spend even more time trying.

Categories

Resources