[Q] APX doesn't show up after flashing a ROM - LG Optimus 2x

ok, so i was using tonyp-harsh v28e vlite ics version before deciding flashing stefan v28g via nvflash
i started nvflash as usual (removing battery + vol up and down), APX driver was recognized and the installation process went smoothly.
the problem is, after i flashed the rom, i found it a lil' bit laggy so i think it'd be better to try CM 10 to find out which one suit me better.
so i turn off my phone again, removing the battery, and pressing vol up & down simultaneously. but then, the phone doesn't respond (yes, it give a blink, but the LG logo doesn't appear and APX doesn't show up in my pc). so, now i'm stuck on v28g
i've tried searching with some queries :
https://www.google.co.id/search?hl=...HMnYrQf7koDADw&ved=0CBwQBSgA&biw=1366&bih=610
https://www.google.co.id/search?q=n...&sugexp=chrome,mod=2&sourceid=chrome&ie=UTF-8
https://www.google.co.id/search?q=l...&sugexp=chrome,mod=2&sourceid=chrome&ie=UTF-8
and such
but it didn't give me an answer
i've also tried another version of nvflash such as this one by ProgMaq and another one by rmein, but nothing works
any suggestion?

babi_perang said:
ok, so i was using tonyp-harsh v28e vlite ics version before deciding flashing stefan v28g via nvflash
i started nvflash as usual (removing battery + vol up and down), APX driver was recognized and the installation process went smoothly.
the problem is, after i flashed the rom, i found it a lil' bit laggy so i think it'd be better to try CM 10 to find out which one suit me better.
so i turn off my phone again, removing the battery, and pressing vol up & down simultaneously. but then, the phone doesn't respond (yes, it give a blink, but the LG logo doesn't appear and APX doesn't show up in my pc). so, now i'm stuck on v28g
i've tried searching with some queries :
https://www.google.co.id/search?hl=...HMnYrQf7koDADw&ved=0CBwQBSgA&biw=1366&bih=610
https://www.google.co.id/search?q=n...&sugexp=chrome,mod=2&sourceid=chrome&ie=UTF-8
https://www.google.co.id/search?q=l...&sugexp=chrome,mod=2&sourceid=chrome&ie=UTF-8
and such
but it didn't give me an answer
i've also tried another version of nvflash such as this one by ProgMaq and another one by rmein, but nothing works
any suggestion?
Click to expand...
Click to collapse
I had the same problem as you face here.
I tried everything NV-flash, smartflash, you name it, no luck. Then I did a emergency repair in the LG updater.
Start the Updater, select "emergency repair", make sure drivers are installed.
Battery out, press Volume Down and connect.
Enter IMEI and S/N and repair program starts.
I had to do it twice, before it finished. I maybe had a bad USB connection or cable, but after "S/W update" showed up in screen on second attempt, I reinserted battery and it went very smooth.
Let it boot.
And then root with NV-flash and you are back in business with normal GB partition table.
I can recommend Tonyp's CWM 6.0.1.5 touch for NV-flash, when you have finished rooting.
It took me 45 minutes, with a not too good internet connection.
PS.: I did not try this one: http://forum.xda-developers.com/showthread.php?t=1715272
but since I could not call up NV-flash, I did not want to spend even more time trying.

Related

[Q] Help me pls.. I think I've really bricked my P990

Hi all kind bros and sis,
Please help me out as I think I've really bricked my less than 2 months brand new Optimus 2X..
You see.. I rooted my P990 using unlock root and chanced upon CM7 and thought of giving it a try. I installed clockworkmod and downloaded the stable release of 7.1 for Optimus 2x.. following the instruction to do a Nandroid backup and proceeded with the Mod..
Not knowing that I need to wipe everything including data.. I just selected the Dalvik cache wipe and proceed with the mod. The process went for more than 15mins and I saw some graphics (the android figure going round and round) but it just stuck there... the screen went blank and when I touched those home or back buttons.. they will lighted but nothing happens. I can't power it off also. So I manually took out the battery and put it back before powering up again. The android picture appeared again briefly for about 1 min and just hanged there. I took out the battery again and this time it was dead.. no matter what I press : vol + and power buttons together; home+Vol+ + power down; Vol- + power down.. all those do not revive the phone.
I tried taking out the external SD card and try powering up. The LG logo appeared and got stuck there.
I searched on Google and found the smartflashtool. I tried that and managed to install the NVidia boot recovery driver and stuff correct. Hold the vol+ button and power key before plugging in but the smarttool did not find the com port or communication driver whatever so I couldn't flash it back to stock.
I'm very desperate and stuck now... did I just accidentally burned the board or something? What bad luck I have
If that's the case, will I still be able to bring the phone back to LG service centre and get it repaired?
Please help me.. any kind souls out there. I really liked the phone and hoped to bring it back. else it's such a shortlived phone... really breaks my heart to see this..
Thanks in advance...
humblepie88 said:
Hi all kind bros and sis,
Please help me out as I think I've really bricked my less than 2 months brand new Optimus 2X..
You see.. I rooted my P990 using unlock root and chanced upon CM7 and thought of giving it a try. I installed clockworkmod and downloaded the stable release of 7.1 for Optimus 2x.. following the instruction to do a Nandroid backup and proceeded with the Mod..
Not knowing that I need to wipe everything including data.. I just selected the Dalvik cache wipe and proceed with the mod. The process went for more than 15mins and I saw some graphics (the android figure going round and round) but it just stuck there... the screen went blank and when I touched those home or back buttons.. they will lighted but nothing happens. I can't power it off also. So I manually took out the battery and put it back before powering up again. The android picture appeared again briefly for about 1 min and just hanged there. I took out the battery again and this time it was dead.. no matter what I press : vol + and power buttons together; home+Vol+ + power down; Vol- + power down.. all those do not revive the phone.
I tried taking out the external SD card and try powering up. The LG logo appeared and got stuck there.
I searched on Google and found the smartflashtool. I tried that and managed to install the NVidia boot recovery driver and stuff correct. Hold the vol+ button and power key before plugging in but the smarttool did not find the com port or communication driver whatever so I couldn't flash it back to stock.
I'm very desperate and stuck now... did I just accidentally burned the board or something? What bad luck I have
If that's the case, will I still be able to bring the phone back to LG service centre and get it repaired?
Please help me.. any kind souls out there. I really liked the phone and hoped to bring it back. else it's such a shortlived phone... really breaks my heart to see this..
Thanks in advance...
Click to expand...
Click to collapse
Try using SmartFlashTool, download the LG stock ROM (can be found here in XDA forum, i'll help you find the link), flash the .bin and .fls files.
humblepie88 said:
Please help me out as I think I've really bricked my less than 2 months brand new Optimus 2X..
...
"Hold the vol+ button and power key before plugging in but the smarttool did not find the com port..."
Click to expand...
Click to collapse
Turn off the phone. Hold Vol-DOWN while plugging it in. Start Smartflash and see the com-ports magically appear.
Follow trymhansen's instructions. He helped me before with my softbricked phone.
I hope you get your O2X back to life! Keep us posted
Best of luck to you!
PS. I also believe you should pull out the battery after turning off the phone in Trym's instructions. Trym correct me if I'm wrong please.
Hi All,
Thanks for your kind replies. I did follow your instruction. Take out the battery (I removed the ext SDcard as well), press and hold -vol and plug in the phone via USB. Afterwhich start up smartflash tool.. still nothing happens and no com ports are found.. The version of smartflashtool that I used is Dec 2010. Do I need to get the latest one and also the LG united drivers installed?
I also tried starting smartflash tool before the sequence.. still the same. BTW.. my OS is Win 7. Is it supported?
Really at my end's wit. Hope I can bring my phone back to life soon and I'm not really bricking it. I heard Samsung phones are not that easy to brick and can get to the recovery mode pretty easily. is it true?
Please help me.. thanks
Hi bros,
Attached are my screenshots from the device manager and smartflash tool... both seems not able to find the phone and allocate a com port. I've tried installing the latest LG mobile driver 3.6 but no help as well
Have you followed instructions as described here http://forum.xda-developers.com/showthread.php?t=1008070 ?
Also, try to attach your phone directly to computer, using usb ports from computer mainboard. I have experienced problems when attaching it via extension usb cord or attaching it to computer case ports. (I hope that you can understand what I have mean to say with usb )
Hi Memhis,
Yes.. I followed exactly the instructions from the thread and I've plugged into a USB port directly to the computer which is one of the ports in front.. not via any extension or USB hub.. still it did not detect.
I'll try to use another computer which is running Win XP and try again. I've downloaded those 3 files from that thread you recommended try using those instead.. hope it can be detected this time else I think I'll have to send to LG service for repair tomorrow.
I've been jailbreaking and modding my Iphone a lot and everytime whenever there's a near brick situation.. I'm able to fix it but not this time with an Android or LG perhaps... I hope I don't have to go to the extend of using ADB low level to push some files which I saw in one of the thread that one of the guys did that.. but I doubt I can since my windows can't even detect the phone!!
Maybe this will be my first and last LG phone if I ever get it repaired...
humblepie88 said:
Hi Memhis,
Yes.. I followed exactly the instructions from the thread and I've plugged into a USB port directly to the computer which is one of the ports in front.. not via any extension or USB hub.. still it did not detect.
I'll try to use another computer which is running Win XP and try again. I've downloaded those 3 files from that thread you recommended try using those instead.. hope it can be detected this time else I think I'll have to send to LG service for repair tomorrow.
I've been jailbreaking and modding my Iphone a lot and everytime whenever there's a near brick situation.. I'm able to fix it but not this time with an Android or LG perhaps... I hope I don't have to go to the extend of using ADB low level to push some files which I saw in one of the thread that one of the guys did that.. but I doubt I can since my windows can't even detect the phone!!
Maybe this will be my first and last LG phone if I ever get it repaired...
Click to expand...
Click to collapse
launch smartflashtool first, extract the .fls and .bin files, hold down volume at the same time plug in the usb port to your comp. you must see a s/w updating logo in your phone's screen and smartflash should detect your phone. then click start!
Sent using a phone.
Hi mrgian,
I just tried to revive my phone by using the same method on a different laptop running on Win XP.. plugged directly to a side USB port but still no luck. There's no s/w updating logo appearing on my phone and smartflashtool also failed to detect my phone. I've found another thread opened by another user and my situation is exactly the same as his :
http://forum.xda-developers.com/showthread.php?t=1161583
But lucky for him is that he's able to get it working after changing to another PC but I've tried 3 different machines and no luck so far...
I'll try to use the NVflash as a last resort and see if I've any luck with NVflash at all.. If it failed again.. I think I've no choice but to send it to the repair centre for servicing then..
humblepie88 said:
Hi mrgian,
I just tried to revive my phone by using the same method on a different laptop running on Win XP.. plugged directly to a side USB port but still no luck. There's no s/w updating logo appearing on my phone and smartflashtool also failed to detect my phone. I've found another thread opened by another user and my situation is exactly the same as his :
http://forum.xda-developers.com/showthread.php?t=1161583
But lucky for him is that he's able to get it working after changing to another PC but I've tried 3 different machines and no luck so far...
I'll try to use the NVflash as a last resort and see if I've any luck with NVflash at all.. If it failed again.. I think I've no choice but to send it to the repair centre for servicing then..
Click to expand...
Click to collapse
does the laptop have lg drivers installed?
Sent using a phone.
inflance hotota
mrgian said:
does the laptop have lg drivers installed?
Sent using a phone.
Click to expand...
Click to collapse
Yes.. I've installed the latest LG united mobile driver version 3.6. Any wrong with that version... Really don't know where / what is missing or my phone is really fried after just one mod attempt?
I've also tried NVflash and it's stuck at the "bootloader initialization" screen....
Nothing appeared on the phone... not even LG logo. Can't believe LG phones are so fragile and unmodifiable
humblepie88 said:
Yes.. I've installed the latest LG united mobile driver version 3.6. Any wrong with that version... Really don't know where / what is missing or my phone is really fried after just one mod attempt?
I've also tried NVflash and it's stuck at the "bootloader initialization" screen....
Nothing appeared on the phone... not even LG logo. Can't believe LG phones are so fragile and unmodifiable
Click to expand...
Click to collapse
can you entet CWM? Press volume down til s/w will appear.
Sent using a phone.
try to charge the battery first...power off your device and charge it...maybe leave it charging for about 1hr even if you dont see anything on the screen( i believe after plugin the charger you will see the charging logo but it will disapear after a few seconds)...after 1 hr unplug and try to check if it will boot to clockwork recovery...if yes then just do complete data wipe...also try installing the ext3 back.zip, it will help delete system files(sometimes CWR is not deleting this)...hope this help
chupi_24 said:
try to charge the battery first...power off your device and charge it...maybe leave it charging for about 1hr even if you dont see anything on the screen( i believe after plugin the charger you will see the charging logo but it will disapear after a few seconds)...after 1 hr unplug and try to check if it will boot to clockwork recovery...if yes then just do complete data wipe...also try installing the ext3 back.zip, it will help delete system files(sometimes CWR is not deleting this)...hope this help
Click to expand...
Click to collapse
you got a point there.
Sent using a phone.
humblepie88 said:
Yes.. I followed exactly the instructions from the thread and I've plugged into a USB port directly to the computer which is one of the ports in front.. not via any extension or USB hub.. still it did not detect.
Click to expand...
Click to collapse
When you say an USB port in the front do you mean an USB in the back? Because the ones in front are the case ones, the ones in the back are the good ones, i.e. the ones that are directly attached to the mobo.
LarsPT said:
When you say an USB port in the front do you mean an USB in the back? Because the ones in front are the case ones, the ones in the back are the good ones, i.e. the ones that are directly attached to the mobo.
Click to expand...
Click to collapse
I've tried the recovery via 2 diff laptops and plugging in directly to one of the side USB ports but to no avail as well.. I think I've plugged in the phone correctly but there's no reaction at all/
mrgian said:
can you entet CWM? Press volume down til s/w will appear.
Sent using a phone.
Click to expand...
Click to collapse
How to enter CWM? I can't even power up the phone and no reaction at all when plugged into USB via smartflash.. the screen remains black. It's liked the whole phone is burned or something... but strange thing is that it can detect APX and asked to install drivers... but after successfully installing the Nvidia boot recovery driver.. the com ports does not get discovered.. What is wrong?
chupi_24 said:
try to charge the battery first...power off your device and charge it...maybe leave it charging for about 1hr even if you dont see anything on the screen( i believe after plugin the charger you will see the charging logo but it will disapear after a few seconds)...after 1 hr unplug and try to check if it will boot to clockwork recovery...if yes then just do complete data wipe...also try installing the ext3 back.zip, it will help delete system files(sometimes CWR is not deleting this)...hope this help
Click to expand...
Click to collapse
I plugged in the phone with battery but there was no charge logo or whatever.. the screen remains blank.. I'll try to leave it charging and see what happens. But I've remembered there was still about 80% power when this disaster happened and I've taken out the battery since.. so the charge should have remain? Btw.. where can I get this ext3 back.zip and how to use it? thanks

Stuck in boot

My LG Optimus 2X from windmobile is stuck in boot screen. I recently rooted my phone which worked perfectly fine than I installed CWM ext which messed things up, phone was hard resetting every time it started up. So I went to the market place and installed CWM and installed recovery from within the app and decided to install [ROM] MIUI v4 2.7.20 [Multilang][New base] [25/07/2012] through the CWM app. It loads up in recovery FINALLY and I installed it. After reboot its just stuck on LG boot screen I cant go into recovery mode either it just reboots and gets stuck at boot screen. is there anything that i can do to recover the phone?
how u tried this? - http://forum.xda-developers.com/showthread.php?t=1006745
i have done it a couple of times after a bad flash on my P990 and it works great.
i got the NVFlash ready, take out the battery and while pushing down Power and Vol. down button i connect the usb cable and it starts up and u can open NVFlash and let it do it's work.
thank you lets see if it works out:fingers-crossed:
puma99dk| said:
how u tried this? - http://forum.xda-developers.com/showthread.php?t=1006745
i have done it a couple of times after a bad flash on my P990 and it works great.
i got the NVFlash ready, take out the battery and while pushing down Power and Vol. down button i connect the usb cable and it starts up and u can open NVFlash and let it do it's work.
Click to expand...
Click to collapse
hey so NVFlash did work but now i am getting no signal, I went to settings> About phones > baseband: unknown. So I decided to use smart flash and flash the "LG_P990_1035_21_2011-06-22", it just wouldn't flash it loads up to 50% than i get timed out error. Is there anyway to fix this issue.
Thanks.
ali2k4 said:
hey so NVFlash did work but now i am getting no signal, I went to settings> About phones > baseband: unknown. So I decided to use smart flash and flash the "LG_P990_1035_21_2011-06-22", it just wouldn't flash it loads up to 50% than i get timed out error. Is there anyway to fix this issue.
Thanks.
Click to expand...
Click to collapse
this might be an issue with BB and RIL combination...try to install the GetRIL app from the play store and try to install a recommended RIL....reboot and check...
you can try the smartflash after trying this...
Hope this helps
The problem was that I was flashing p990 firmware on my P999. oddly enough it ran but without any baseband. long story short I used the ROM from this thread http://forum.xda-developers.com/showthread.php?p=17258229 and it worked I was in the wrong phone section the whole time. thanks every one for the help couldn't have recovered it without your help thanks :victory:

[Q] Semi-bricked / Smartflash tool not working

Hi
I'm helping out a friend, which O2X I have rooted and flashed WIUI on to (I previously owned one myself too)
For some reason the phone started to get hot after a while and used up the battery fast, until one day where he couldn't even turn it on again.
Now, he has been trying to fix it himself with NVflash, but no luck, so now its up to me and you guys.
I have used the smartflash tool and flashed the EURO OPEN stock ROM and everything went succesfull, but when the phone reboots, the LG logo appears, and it bootloops.
I tried both with battery and no battery in, but still no cigar.
Any suggestions what I should try next?
PS: If I try to turn on the phone normally, nothing happens. not even a blink from the screen, but I can get into S/W mode and APX
Try lg update tool, choose recover as option, then choose imei as entrance
SuperSkill said:
Try lg update tool, choose recover as option, then choose imei as entrance
Click to expand...
Click to collapse
EDIT: The software says the update is not compatible (dunno if translation is correct, but you get the point)
Update is aborted :/
No more suggestions on what to do?
Tried:
NVflash
Smartflash (Flashed EURO OPEN rom)
LG Update tool (recover function)
The phone still won't boot.
Smartflash is the only solution like you said that the phone can boot in s/w mode try to dig some answer in smartflash thread or search in google i know you can find some answer there
Sent from my Optimus 2X using xda premium
Assuming you have carried out the procedures correctly, looks like this device is actually defective. Probably not what you want to hear, I know, but...
Before giving up completely, you can NVFlash it again (using the original 10C NVFlash from Modaco) and post the log here. Wouldn't get my hopes up though.

[Guide] Enter Emergency Download Mode LG Optimus L5 E615/E615F [Guide]

[Guide] Enter Emergency Download Mode LG Optimus L5 E615/E615F [Guide]
You can enter Emergency Download Mode (EDM) on LG Optimus L5 E615
by using the following key combination
Firstly, make sure your phone is switched off and remove any SIM cards
inside it. To ensure your phone is switched off, please remove the battery.
Now re-insert the battery.
Key Combination:
#1 Press and hold both the “Vol Up” and “Vol Down” buttons. (Easy way
is to press in the center of both the buttons).
#2 Next press the Power button.
#3 As soon as the screen turns on insert the USB cable to your computer.
If successful, You will a LG Home screen with a syncing sign at the center bottom of the
screen and above it will be written “Downloading in progress, please do
not disconnect or power off the phone.” (OR SIMILAR).
Purpose:
If you have tried to enable animated boot menu's which will make the
screen hang while booting up and in most severe cases make the phone
un-bootable.
How to use:
#1 Firstly, note down the IMEI of your mobile. You can do this by
removing the back cover and battery. After removing the battery you
will see IMEI1 and IMEI2. Note both of them down. Either one can be
used.
#2 Next you will need to make sure that the PC you will be using has LG
PC Suite installed, with latest USB drivers and LG Support Tool.
#3 After putting your phone in EDM you can connect it to LG Support
Tool, it will hopefully receive the required information. If it doesn't
then you can manually go to options >> recovery >> enter IMEI.
#4 Next, your phone should be discovered and the software tool will
automatically download the latest STOCK FIRMWARE for the mobile.
#5 Essentially, if all above fails, and your phone is still not discovered by
the tool, you can restart the process and this time after putting your
phone in EDM you can directly open up LG PC Suite and you can go to
Tools/Options and click support tool/phone recovery.
#6 In the above case your phone should be recognized, if it doesn't then
manually input your IMEI as mentioned earlier. And all will work out
IF I HELPED, PLEASE KINDLY SAY THANKS, IT TAKES WEEKS TO WRITE A PROPER GUIDE, BUT MINUTES TO SAY THANKS.
HAPPY HUNTING AND FLASHING​
Could you please number the steps, so that it will be easy to follow the step by step instructions. If the EDM mode is followed, what will be the Android software that gets installed on the mboile? Will it be be ICS for E615 or any ealrier version. The reason I asked because
1. I connected my phone via USB to PC (Selected the option "Connect LG SOftware")
2. Opened LG supported tool.
3. Selected "Recover phone"
4. It asked to enter the IMEI.
5 .After entering IMEI, it showed the model as E615 and when clicked "Yes", I got the below msg
"
- After upgrading the OS (eg. Android 1.6 Donut; Andorid 2.1 Eclair), user data will be erased. Therefore, please backup all the data prior to the upgrade process.
- Applications previosuly download from Android market will be earsed as well". However any data stored in SD will remain.
- After upgrading OS, user will not be able to restore to the previous version even Factory reset is performed.
Would you like to conitnue (Yes/NO)
"
I was not activating the EDM mode. Just I was tryign to familiarize with the LG Support tool. But at the same time, worried in case if we want to activate EDM, then will the Android verson be same (ICS) or the previous version?
Yes it will ask u that and u have to comply, whether it is EDM or not
with the after it starts updating my sofware it freezes at 4% ? help
My Device Not Entering to Emergency Mode
Help Please!
My device not Entering to emergency mode, so i'm not flashing my device.
My Device Trouble is Bootloop, stuck in LG Logo. please help me master
thanks this is very helpfull to noobs like me. this is always my last resort to restoring my phone whenever I softbrick my phone.
THe whole recovery function finishes but the phone still does not boot up what may be the reason?
The reason for the phone not booting up is that the System memory has been flashed. Try to enter the EDM once again and Hopefully that should work out for you. Post your feedback here.
Hello kingmak my name is evi i am from nigeria, i have an LG-E615 i would want to be friends with you and also ask for assistance in flashing a custom rom to my phone, will you help me
Sent from my LG-E615 using xda premium
OK but what if there is no button combination is possible?
XxXKINGMAKXxX said:
[Guide] Enter Emergency Download Mode LG Optimus L5 E615/E615F [Guide]
You can enter Emergency Download Mode (EDM) on LG Optimus L5 E615
by using the following key combination
Firstly, make sure your phone is switched off and remove any SIM cards
inside it. To ensure your phone is switched off, please remove the battery.
Now re-insert the battery.
Key Combination:
#1 Press and hold both the “Vol Up” and “Vol Down” buttons. (Easy way
is to press in the center of both the buttons).
#2 Next press the Power button.
#3 As soon as the screen turns on insert the USB cable to your computer.
If successful, You will a LG Home screen with a syncing sign at the center bottom of the
screen and above it will be written “Downloading in progress, please do
not disconnect or power off the phone.” (OR SIMILAR).
Purpose:
If you have tried to enable animated boot menu's which will make the
screen hang while booting up and in most severe cases make the phone
un-bootable.
How to use:
#1 Firstly, note down the IMEI of your mobile. You can do this by
removing the back cover and battery. After removing the battery you
will see IMEI1 and IMEI2. Note both of them down. Either one can be
used.
#2 Next you will need to make sure that the PC you will be using has LG
PC Suite installed, with latest USB drivers and LG Support Tool.
#3 After putting your phone in EDM you can connect it to LG Support
Tool, it will hopefully receive the required information. If it doesn't
then you can manually go to options >> recovery >> enter IMEI.
#4 Next, your phone should be discovered and the software tool will
automatically download the latest STOCK FIRMWARE for the mobile.
#5 Essentially, if all above fails, and your phone is still not discovered by
the tool, you can restart the process and this time after putting your
phone in EDM you can directly open up LG PC Suite and you can go to
Tools/Options and click support tool/phone recovery.
#6 In the above case your phone should be recognized, if it doesn't then
manually input your IMEI as mentioned earlier. And all will work out
IF I HELPED, PLEASE KINDLY SAY THANKS, IT TAKES WEEKS TO WRITE A PROPER GUIDE, BUT MINUTES TO SAY THANKS.
HAPPY HUNTING AND FLASHING​
Click to expand...
Click to collapse
Nothing happens screen doesnt do anything, pc does not recognize usb connection, no driver works. Read below,
Quote:
Originally Posted by breakercris
I've tried everything.
The phone simply doesn't connect.
USB\VID_05C6&PID_9008&REV_0000
This is what I get when I connect the phone by USB.
I just cant get into emergency, DIAG or emergency CS
KDZ the phone connects and then I get a message afterwards PHONE NOT FOUND.
everytime I install the drivers by LG support tool, it keeps giving me the option to install the driver, like I havent done it a hundred times over.
I think there should be a driver somewhere that can be installed but the only people that have this driver are LG tech's. So they can bill you after
send the phone in cause you rooted it. So the one billion dollar question is witch hero will find a way to unbrick this device. We only need a way
to get a driver to install and we are home free. Or maybe the only other option is throwing the phone for sale on internet for spare parts
HELP PLEASE HELP find a way to unbrick this phone. Believe me I flashed and bricked alot of different phones and there was a way out but in
with this phone it seems impossible!!
And there is no mode to put it in in because te volume buttons don't do crap, the home button also, the only time that the phone does show up is when windows tells me it has an unknown device that I for the love of god can't find a driver for. I tried SDK, the LG drivers, but no dice
any other options??
Easy Peasy
@breakercris
The solution to your above mentioned Problem is very very easy. Not techy at all.
Basically there might be some drivers that might be conflicting.
Try to fix things in Device Manager and post screen shots here.
Also if you are unable to get them working then try a Reformat for your PC. IMHO go for WINDOWS 7 or 8.
Lastly remove the battery of your phone.
Also make sure you have LG PC Suite Installed and LG Support Tool Installed as well.
Hold down the power and the volume buttons and insert the USB Cable into the PHONE WITHOUT THE BATTERY, and my dear friend you will be home free.
Sincerely,
XxXKINGMAKXxX
PS. If you still need some help, PM me
I appreciate in writing the steps to install firmware. It would be great if there is some info on how to avoid the online firmware download. Do you have any info on that?
XxXKINGMAKXxX said:
[Guide] Enter Emergency Download Mode LG Optimus L5 E615/E615F [Guide]
You can enter Emergency Download Mode (EDM) on LG Optimus L5 E615
.
.
.
.
IF I HELPED, PLEASE KINDLY SAY THANKS, IT TAKES WEEKS TO WRITE A PROPER GUIDE, BUT MINUTES TO SAY THANKS.
HAPPY HUNTING AND FLASHING​
Click to expand...
Click to collapse
Yes you can use kdz flasher to install it offline. You should have the ROM downloaded for this to work
Sent from my GT-I9300 using xda premium
Hi. I'll use this thread to ask something related. I've a LG L5 E610. Wanted to flash a generic brand-free rom and apparently i need to boot to emergency mode (vol up + vol down + power) except the phone can't boot to any mode except for a regular boot - phone works perfectly with a simple boot just using the power button. If i try any key combo all i get are the bottom soft keys (back and options) quickly flashing. That's it, screen stays off, nothing more happens.
Phone's new, all i did was reseting it (vol down + home + power) and rooted it following some method i found around here (worked flawlessly too). I also know vol up + home + power also used to work before this (tried it by accident before).
Any ideas? Thanks!
cant update when i try to update online every time say battrey low
my battrey lavel is 100% where is problem ?
gauravrajput said:
cant update when i try to update online every time say battrey low
my battrey lavel is 100% where is problem ?
Click to expand...
Click to collapse
Well it must be a phone issue, previously when I tried to upgrade my phone, it used to give me the error after downloading and just before installing, PHONE SOFTWARE NOT COMPATIBLE.
I just realized that the bootloader and the Software version for the region were not properly set.
About the Battery issue, well try it with a new battery, or else try to clear battery statistics. EDM should basically allow you install the Original Firmware.
Anyways, google up the Stock Rom for your phone, they are most likely available on
http://www.ninjaromeo.com/unbrick-lg-optimus-l5-using-kdz/
http://lg-phone-firmware.com/index.php?id_mod=12
ukekoe said:
Hello kingmak my name is evi i am from nigeria, i have an LG-E615 i would want to be friends with you and also ask for assistance in flashing a custom rom to my phone, will you help me
Sent from my LG-E615 using xda premium
Click to expand...
Click to collapse
There are some guide
There are a couple of guides out there that would help you install the STOCK or CUSTOM roms on your LG Mobile, the best one that has been around for quite sometime is KDZ Flasher. Give it a try and hopefully everything works fine.
Regards,
MAK
HELP!!!!!!!!
Hello Kingmak! My lg optimus. L5 is stuck on white screen I can hear the sound but the screen stays white PLEASE HELP ME OUT DUDE AS SOON AS POSSIBLE.
thanks in advance
Well i have never heard of such a problem before. Have a look at your user manual or go to LG website and download the tech manual for your phone for repairs and it will help you with the EDM mode amd you will be good to go.
Sent from my GT-I9300 using XDA Premium 4 mobile app

[Q] Have I managed to HARD-BRICK my phone?

Switched from one provider to another, got a new phone which uses micro-sim, and couldnt get the p880 to read the new sim card, so I have been using the new phone, which is greatly inferior to the p880..
With the p880 just sitting around unused, i decided i might as well try to mod it, then get a regular sim card for it and start using it again. I think i killed it instead.
Before it died on me, I formatted / wiped / factory reset and then used the LG Mobile Support tool to upgrade to whatever the newest official release was.. 4.1.2??
At this point, here is what it can do:
1) When attempting to just turn it on and USE it as normal, it turns on, gets to the animated LG logo and stays there forever.
2) Power + Vol Down = OEM LG recovery menu
3) Power + Vol Up = Some kind of Restore graphic
4) Power + Vol Up and Down (AVX) = nothing
5) Plugged into USB with battery removed and holding Vol Down = home row LEDs light up, nothing else
Windows sees the phone as a "removable disk H:" when I plug it in, but the LG recovery software does not see it, and it also does not show up in the device manager..
At this point, all that I can seem to access is the "apply update from ADB" option to do an "adb sideload" command in recovery mode.. When I send over the root tool, the phone is happy. If I attempt to send anything else over via sideload, I always get kicked out of the process when it gets to the "verifying installation package" portion. I can wipe / factory reset to my heart's content, but I can get absolutely no further than this after attempting for about six hours yesterday.
Any hope for me or do i have a dope looking paperweight? Will providing you guys either the IMEI or S/N shed any light into a path to recovery?
Thanks for your time!
You have a booting rom, the device is not even close to hard brick. Is your bootloader unlocked? If yes you can flash a custom recovery with fastboot and install any rom you want.
Sent from my OmniROM-powered LG Optimus 4X HD
@one30six
Use this thread http://forum.xda-developers.com/showthread.php?t=2069723 or
Use this thread http://forum.xda-developers.com/showthread.php?t=2179126 to recover your phone.
Read the instructions with care and act as stated.
Good Luck.
sPEADy said:
@one30six
Use this thread http://forum.xda-developers.com/showthread.php?t=2069723 or
Use this thread http://forum.xda-developers.com/showthread.php?t=2179126 to recover your phone.
Read the instructions with care and act as stated.
Good Luck.
Click to expand...
Click to collapse
thank you, speady.. it turned out to be the first solution that you suggested, which i had seen before during my scouring of these forums.. but the real basis of my problem was that i had my phone plugged into the front-facing USB port of my computer rather than the one directly connected to the motherboard (on the back).. i guess the phone wasnt getting enough juice out of the front port to boot to S/W Update mode.. i am back to stock LG software and am eventually going to mod to another ROM
THANK YOU!

Categories

Resources